English dropdown-ico

Manual Henny Penny OFE-321

14 pages 1.43 mb
Download

Go to site of 14

Summary
  • Henny Penny OFE-321 - page 1

    Model OFE-321,322 SECTION 2. MAINTENANCE 2-1. INTRODUCTION This section provides procedures for the checkout and replacement of the various parts used within the fryer. Before replacing any parts, refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. You may need to use a multim ...

  • Henny Penny OFE-321 - page 2

    Model OFE-321,322 2-4. POWER SWITCH 1. Remove electrical power supplied to fryer. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove control panel. 3. Label and remove the wires from the switch. W ith test instrument, check across the terminals ...

  • Henny Penny OFE-321 - page 3

    Model OFE-321,322 2-6. I/O POWER SUPPLY BOARD ASSEMBLY The input/output power supply board assembly distributes voltage to the various components in the fryer. The board also receives information from com ponents in the fryer. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER switch to OFF ...

  • Henny Penny OFE-321 - page 4

    Model OFE-321,322 2-7. DRAIN MICROSWITCH (Continued) 2. The following check should be made to determine if the drain microswitch is defective. a. Remove the two screws securing the microswitch to the drain rod valve bracket. b. Remove wires from the switch. c. Check for continuity across the two outside terminals of the drain switch. If the circuit ...

  • Henny Penny OFE-321 - page 5

    Model OFE-321,322 2-9. HEATING ELEMENTS Heating elements are available for 208 , 480 and 230 volts. Check data plate to determine correct voltage. C h e c k o u t : If the shortenings temperature recovery is very slow or at a slower rate than required, this may indicate defective heating element(s). An ohmmeter will quickly indicate if the elements ...

  • Henny Penny OFE-321 - page 6

    Model OFE-321,322 2-9. HEATING ELEMENTS (Continued) 3. Remove the heating element wires from the term inals by removing the nuts and washers. Label each so it can be replaced on the new element in the same position. 4. Remove the bolts from the five elem ent spreaders. The element spreaders will now pull off the elem ents. 5. Remove the brass nuts ...

  • Henny Penny OFE-321 - page 7

    Model OFE-321,322 2-9. HEATING ELEMENTS (Continued) 13. Connect the power cord to the wall receptacle or close wall circuit breaker. Heating elements should never be energized without shortening in the frypot, or damage to the elements could result. 14. Replace the shortening in the frypot. Fig. 2-2 2-7 405 ...

  • Henny Penny OFE-321 - page 8

    Model OFE-321,322 2-10. HEATING CONTACTORS Each well of an electric fryer requires two switching contactors. The first in line is the primary contactor and the second in line is the heat contactor. When open, the primary contactor does not allow power to flow to the heat contactor. When closed, the primary supplies voltage to the heat contactor. Wh ...

  • Henny Penny OFE-321 - page 9

    Model OFE-321,322 2-10. HEATING Checkout (Power Supplied) CONTACTORS (Continued) To avoid electrical shock, make connections before applying power, take reading, and remove power before removing meter leads. The following checks are performed with the wall circuit breaker closed and the main power switch in the ON position. 1. Re-apply power to uni ...

  • Henny Penny OFE-321 - page 10

    Model OFE-321,322 2-11. SPEAKER ASSEMBLY The speaker assembly emits audible signals to let the operator know when cooking and hold times are finished. 1. Remove electrical power supplied to unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remo ...

  • Henny Penny OFE-321 - page 11

    Model OFE-321,322 2-12. HIGH TEMPERATURE LIMIT CONTROL The electric units, models OFE-321/2/3/4, use the same high temperature control limits as the gas units, but the m ounting of the capillary tube is different on the electric units compared to the gas u n i t s . Checkout: Use the same procedure as in the High Limit Tem perature Control (Gas) Se ...

  • Henny Penny OFE-321 - page 12

    Model OFE-321,322 2-12. HIGH TEMPERATURE LIMIT CONTROL (Continued) Be sure capillary bulb of high limit is located behind capillary bulb of thermostat. Both capillary bulbs and bulb holders should be positioned as not to interfere with basket or when cleaning the frypot wall, or damage to capillary tube could result. 13. With excess capillary line ...

  • Henny Penny OFE-321 - page 13

    Model OFE-321,322 2-13 707 ...

  • Henny Penny OFE-321 - page 14

    Model OFE-321,322 707 2-14 ...

Manufacturer Henny Penny Category Fryer

Documents that we receive from a manufacturer of a Henny Penny OFE-321 can be divided into several groups. They are, among others:
- Henny Penny technical drawings
- OFE-321 manuals
- Henny Penny product data sheets
- information booklets
- or energy labels Henny Penny OFE-321
All of them are important, but the most important information from the point of view of use of the device are in the user manual Henny Penny OFE-321.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Henny Penny OFE-321, service manual, brief instructions and user manuals Henny Penny OFE-321. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Henny Penny OFE-321.

Similar manuals

A complete manual for the device Henny Penny OFE-321, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Henny Penny OFE-321 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Henny Penny OFE-321.

A complete Henny Penny manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Henny Penny OFE-321 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Henny Penny OFE-321, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Henny Penny OFE-321, that we can find in the current document
3. Tips how to use the basic functions of the device Henny Penny OFE-321 - which should help us in our first steps of using Henny Penny OFE-321
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Henny Penny OFE-321
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Henny Penny OFE-321 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Henny Penny OFE-321?

Use the form below

If you did not solve your problem by using a manual Henny Penny OFE-321, ask a question using the form below. If a user had a similar problem with Henny Penny OFE-321 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)