English dropdown-ico

Manual Audiovox PRO-9056

19 pages 0.41 mb
Download

Go to site of 19

Summary
  • Audiovox PRO-9056 - page 1

    128-7762 1 of 19 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be selected to operate from the v ...

  • Audiovox PRO-9056 - page 2

    128-7762 2 of 19 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch 1 ...

  • Audiovox PRO-9056 - page 3

    128-7762 3 of 19 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Not Available 2nd RF S t art Chirp Not Available 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins 4th ...

  • Audiovox PRO-9056 - page 4

    128-7762 4 of 19 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output pu ...

  • Audiovox PRO-9056 - page 5

    128-7762 5 of 19 This Remote S tart System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is ...

  • Audiovox PRO-9056 - page 6

    128-7762 6 of 19 IMPORT ANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INT O THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCONNECT THE NEGA TIVE BA TTERY CABLE FROM THE VE- HICLE BA TTERY PRIOR TO MAKING ANY CONNECTIONS. WIR ...

  • Audiovox PRO-9056 - page 7

    128-7762 7 of 19 SEE NEUTRAL S T ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions and will have 0 volts ...

  • Audiovox PRO-9056 - page 8

    128-7762 8 of 19 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or ...

  • Audiovox PRO-9056 - page 9

    128-7762 9 of 19 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...

  • Audiovox PRO-9056 - page 10

    128-7762 10 of 19 the applications described below , a relay will be required. The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote S tart activation period, then vibration from the running vehicle can cause the al ...

  • Audiovox PRO-9056 - page 11

    128-7762 11 of 19 cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a single coil unit for each cylinder , it may be necessary to connect this wire to more than one cylinder for proper tach reference. See multi coil wiring detail shown later in this manual for additional information. T ac ...

  • Audiovox PRO-9056 - page 12

    128-7762 12 of 19 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows sof tware selections to control the way in which this output oper- ates, see remote start feature # 10 for setting this output. When the u ...

  • Audiovox PRO-9056 - page 13

    128-7762 13 of 19 columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylinder number which appears in any of the circles. 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8 cylinder , four coil systems, connect to any of the three co ...

  • Audiovox PRO-9056 - page 14

    128-7762 14 of 19 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. T emporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch. 4. Sitting in the vehicle, start the engine using the vehicle's ignition key . 5. S tep on the brake pedal and shift the gear selecto ...

  • Audiovox PRO-9056 - page 15

    128-7762 15 of 19 AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACT ORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the ...

  • Audiovox PRO-9056 - page 16

    128-7762 16 of 19 C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to the Remote S tart Negative Safety Shut down Wire Gray/ Black, using a 4002 series diode as shown above. NOTE: A second 4002 series diode may be required to maintain the integr ...

  • Audiovox PRO-9056 - page 17

    128-7762 17 of 19 ...

  • Audiovox PRO-9056 - page 18

    128-7762 18 of 19 THIS PAGE LEFT BLANK INTENTIONALLY ...

  • Audiovox PRO-9056 - page 19

    128-7762 19 of 19 © 2006 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7762 ...

Manufacturer Audiovox Category Automobile Accessories

Documents that we receive from a manufacturer of a Audiovox PRO-9056 can be divided into several groups. They are, among others:
- Audiovox technical drawings
- PRO-9056 manuals
- Audiovox product data sheets
- information booklets
- or energy labels Audiovox PRO-9056
All of them are important, but the most important information from the point of view of use of the device are in the user manual Audiovox PRO-9056.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Audiovox PRO-9056, service manual, brief instructions and user manuals Audiovox PRO-9056. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Audiovox PRO-9056.

Similar manuals

A complete manual for the device Audiovox PRO-9056, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Audiovox PRO-9056 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Audiovox PRO-9056.

A complete Audiovox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Audiovox PRO-9056 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Audiovox PRO-9056, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Audiovox PRO-9056, that we can find in the current document
3. Tips how to use the basic functions of the device Audiovox PRO-9056 - which should help us in our first steps of using Audiovox PRO-9056
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Audiovox PRO-9056
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Audiovox PRO-9056 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Audiovox PRO-9056?

Use the form below

If you did not solve your problem by using a manual Audiovox PRO-9056, ask a question using the form below. If a user had a similar problem with Audiovox PRO-9056 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

jose

como modificar la portada y facilitar el acceso al encender