English dropdown-ico

Manual Lindy 25010

63 pages 0.67 mb
Download

Go to site of 63

Summary
  • Lindy 25010 - page 1

    © LINDY ELECTRONICS LIMITED & LIND Y -ELEK TRONI K GMBH - FIRST EDITION (A pril 2005) GIGA Smart Switch 24 + 2 U s e r M a n u a l English LINDY No. 25010 www .lindy .com ...

  • Lindy 25010 - page 2

    ...

  • Lindy 25010 - page 3

    2 T ABLE OF CONTENTS 1 Introductio n ................................................................................................................................. 4 1.1 S tart to Manage This Sw itch ...................................................................................... 6 1.2 Configuration Functions for the Sw itch .............. ...

  • Lindy 25010 - page 4

    2.1 1 System Setup .............................................................................................................. 46 2.1 1.1 Firmwar e Update .............................................................................................. 47 2.1 1.1.1 Firmwar e Update V ia TFTP ......................................................... ...

  • Lindy 25010 - page 5

    1 Intr oduction The 24/2Giga web smart switch is a high performan ce web-smart layer 2 switch that provides users with 24 switched 10/100/1000Mbps Ethernet por ts and 2 shared mini-GBIC ports with auto-detection function. The management function can be accessed via out of band RS-232 term inal port connection and also via in-band IP access from any ...

  • Lindy 25010 - page 6

    Main Featur es  Broadcom ® chipset  Non-blocking, full-line spee d, store-and-forward operation  Supports normal Ethernet frames and jum bo frames from 64 bytes to 9216 bytes  Auto-negotiation and auto-MDIX on all 10/100/1000M copper ports  24 x 10/100/1000 RJ-45 ports with copper por ts, 2 are shared with mini-GBIC  Auto-detecti ...

  • Lindy 25010 - page 7

    1.1 S tart to Manage This Switch Plug-in the power source to power -u p the switch. After the s witch is powered-on and in a ready state (both the LED indicators POWER and DIAG are lit), you can use any in-band Ethernet port to remotely manage it through a web browser . Alternatively use an RS -232 cable to plug-in the console port (on the rear pan ...

  • Lindy 25010 - page 8

    1.2 Configuration Functions for the Switch After the login is successf ully va lidated, the switch’ s home page – System page will show up. The left part on the page provides the function menus (shown as below) to activate to the individual configuration page. The function menus contain two parts: Switch for setting up the switch functions and ...

  • Lindy 25010 - page 9

    2 Configurations 2.1 Port S tatus This page provides the current link stat us for all ports. Y ou can select the Port S tatus menu to activate this page and to ref res h the current port status. This page provides the following information:  Port – to specify a port on the switch  Link S tatus – to show the port link status: Up / Down  ...

  • Lindy 25010 - page 10

    2.2 Port Configuration If you need to do the port configuration, ju st select the desired port by clicking the Port num ber in the Port S tatus page. Then the Port Configuration page (shown as belo w) for the selected port will be opened: The following parameters will be pr ovided and configured in the Port Configuration page:  Port – the sele ...

  • Lindy 25010 - page 11

     Speed / Duplex – to setup the link speed and duplex mode in force mode The options for this function can be selected only when the Auto Negotiation is Disabled (in force mode ) for copper media . There are 4 options for this parameter: ¾ 100Mbps Full – to set the speed 100Mbps in full duplex mode ¾ 100Mbps Half – to set the speed 100Mbp ...

  • Lindy 25010 - page 12

    2.3 About the Copper/Fibr e Media Auto-Detection This switch provides an option to use either copper or fibre m edi a for the first two combo ports - Port1 and Port2 . This means that you can setup the link by using either copper m edia to plug-in to the copper port or use fibre media to plug-in th e mini-GBIC port. This switch will automatically d ...

  • Lindy 25010 - page 13

    2.4 Port S tatistics The Port S tatistics function lets you see the TX/RX packets th rough each port. The Clear Counters button will clear all packet c ounters to 0. The Refresh button will get port statistics again. Y ou can check each ports statistics m ore precisely . Just click the Port number to see the detailed information. 12 ...

  • Lindy 25010 - page 14

    The table shown below has the de scription for each column. UnicastPkts Number of good unicast packets tran sm itted. MulticastPkts Number of good multicast packets transm itted. BroadcastPkts Number of good broadcast packets transmitted. Single Collision Number of packets in which the tr ansmission experienced one collision Multi Collisions Number ...

  • Lindy 25010 - page 15

    2.5 Port-Based VLAN The port-based VLAN divides the ports into dif fer ent V irtual LAN domain groups. After setting the port-based VLAN, the dif ferent VLAN groups can’ t access each other . The VLAN initial setting page is shown as below: Y ou need to click the Enable/Disable link text to enable /disable the port-based VLAN. When port-based VLA ...

  • Lindy 25010 - page 16

    2.5.1 Add Port-Based VLAN Gr oups T o add a port-based VLAN group, select the Cr eate New VLAN in the VLAN NO dropdown of t he Port-Based VLAN page shown as below: After selecting the Cr eate New VLAN , the page will be changed like this: In the above page, VLAN NO will auto setup. Users just need to set VLAN Port Members. After the settings are co ...

  • Lindy 25010 - page 17

    Below is the example page when the user se ts Port1-12 to the VLAN Group2 after clicking the Create button. Now there is a VLAN group No.2 created with the member Port1-12. While the group No.2 is created, all the members in group No.1 are removed to operate the VLAN function. 16 ...

  • Lindy 25010 - page 18

    2.5.2 Delete Port-Based VLAN Gr oups T o delete a port-based VLAN group, just select a desired group (e.g. No.2) to be removed and click the Remove This VLAN button. Pressing the Remove This VLAN button results in the following: Now all ports are set to the members in VLAN group No.1. 17 ...

  • Lindy 25010 - page 19

    2.5.3 Edit Port-Based VLAN Gr oups T o edit the current port-based VLAN group, first select the group (e.g. group No. 3) you want to edit (to add Port7 & Port8 as members) and c lick the Apply button to activate the setting. The following figure shows the configura tion for the selected group (e.g. No.3). 18 ...

  • Lindy 25010 - page 20

    2.6 802.1Q VLAN IEEE 802.1q (tag-based) VLAN can add or strip the 802.1q tag depending on the requirem ents of the individual transmitting p ort. Click the 802.1Q VLAN menu to activate the fo llowing pages to do the configurations. VLAN ID 1 is the default 802.1Q VLAN. VLAN ID 1 cannot be deleted. However , the VLAN ID 1 group member can be changed ...

  • Lindy 25010 - page 21

    2.6.1 Enable/Disable VLAN In the 802.1Q VLAN page you can enable/disable the ta g-based VLAN function by clicking (Enable) or (Disable) besides the page header: ¾ Enable – to activate the tag-based VLAN f unction (port-based VLAN function will automatically be disabled). ¾ Disable – to de-activate the ta g-based VLAN function, even though the ...

  • Lindy 25010 - page 22

    2.6.2 802.1Q VLAN Port Configuration Click the Port number to enter the port c onfiguration page for 802.1q VLAN. The following figure shows the 802.1Q VLAN Port Configuration page by port. (e.g. Port10) Y ou can set the individu al port for configur ing the 802.1q settings in the following fields: ¾ PVID – enter a valid VLAN ID(1-4094), and PVI ...

  • Lindy 25010 - page 23

    2.6.3 802.1Q VLAN Config The following figure is the page to add/delete/e dit the 802.1q VLAN entry . Each VLAN entry has 3 parameters, VID, T ag Members and UnT ag Members to be assigned. After selecting Create New VLAN the figure shown as below will be displayed: ¾ VID – a unique VLAN ID. The range is from 1 to 4094 ¾ T ag Members & UnT a ...

  • Lindy 25010 - page 24

    Here is an example of how to configure th e 802.1q VLAN. There are f our existing 802.1q VLAN entries as shown below . Y ou can delete the 802.1q VLAN e ntry . Click a radio button on the Select column to select the entry to be deleted (e.g. VID = 200), then click the Remove This VLAN button to do the deletion. After the action mentioned above, the ...

  • Lindy 25010 - page 25

    If you would like to edit the parameters of an 802.1q VLAN, just select a VID to be changed (e.g. VID =300) then click the Apply button to do the modi fications: Port 17 and Port18 are selected to be the tag members of this group. Finally , click the Apply bu tton to do the changes. 24 ...

  • Lindy 25010 - page 26

    2.7 T runk This 24G web smart switch supports MAC-based tr unking, which allows more than one port to be grouped together as a single link co nnection between two switch devices. This is also useful for switch-to-server and switch-to-router applicatio ns. The 24G web smart switch allows four trunk groups that can accommodate up to eight trunk me mb ...

  • Lindy 25010 - page 27

    Because a trunk port can be aggregated by the member ports with the same configurations in most functions for each other , there ar e some rules to limit the configurations of the trunking . The following section will list the re lated rules for this function. 26 ...

  • Lindy 25010 - page 28

    2.7.1 T runking Rules The following rules will limit the conf igurations for port trunking:  The attributes of all trunk member ports in Port Configuration, Mirro r , Rate Control, 802.1Q VLAN and Port-Based VLAN functions must be the sam e.  All trunk member ports can not be a capture port or monitored port in Mirror function.  If Port1/P ...

  • Lindy 25010 - page 29

     When the enabled trunk group is set to disable d, all trunk member ports will be released to ordinary ports and their functi ons can be configured indivi dually . At that moment, their configuration attributes will be re tained to the la st settings while they were mem ber ports of the trunk group. The following 3 figures show how the port conf ...

  • Lindy 25010 - page 30

    2.7.2 Get/Refr esh the Latest T runk Settings Click the T runk menu on the web page, the latest trunk settings on the switch will be displayed. This is also the page to configure the trunk function. 29 ...

  • Lindy 25010 - page 31

    2.7.3 Enable T runk ¾ St e p 1 : Choose the Distribution Criterion. ¾ St e p 2 : Choose the member port(s) up to 8 ports f or each trunk group. ¾ St e p 3 : Click the Apply button to enable trunk settings. 30 ...

  • Lindy 25010 - page 32

    2.7.4 Modify T runk Settings ¾ St e p 1 : Choose the Distribution Criterion. ¾ St e p 2 : Choose the member port(s) up to 8 ports f or each trunk group. ¾ St e p 3 : Click the Apply button to modify trunk settings. 31 ...

  • Lindy 25010 - page 33

    2.7.5 Disable T runk ¾ St e p 1 : Click the Not T runking . ¾ St e p 2 : Click the Apply button to disable trunk. 32 ...

  • Lindy 25010 - page 34

    2.8 Port Mirr oring Port mirroring allows ingress and/or egress traf fic to be monitored by a single port. The single port is mirror capture port. The 24G web smar t switch can be configured to mirror the ingress and/or egress traf fic of another port. Port monitoring is inde pendent of L2 switching. Th e networking manager can monitor all traf fic ...

  • Lindy 25010 - page 35

    2.8.1 Get/Refr esh the Latest Mirr or Settings Click the Mirr or menu on the web page. The mirror settings on the switch will be displayed. This is also the page to configure the port mirroring function. The following parameters ar e required to be set:  Mirroring Options – There are four options for each port: ¾ Disable Mirror – to disable ...

  • Lindy 25010 - page 36

    2.8.2 Enable Mirr or ¾ St e p 1 : Choose Mirror option to be Mirr or All Frames . ¾ St e p 2 : Choose the Monitor ed Port to be Port16. ¾ St e p 3 : Choose the Captur e Port to be Port8. ¾ St e p 4 : Click the Apply button to enable mirroring settings. 35 ...

  • Lindy 25010 - page 37

    2.8.3 Modify Mirr or Settings ¾ St e p 1 : Change Mirror option to be Mirr or Outgoing Frames . ¾ St e p 2 : Change the Monitor ed Port to be Port3 ¾ St e p 3 : Change the Captur e Port to be Port22. ¾ St e p 4 : Click the Apply button to modify mirroring settings. 36 ...

  • Lindy 25010 - page 38

    2.8.4 Disable Mirr or ¾ St e p 1 : Choose Mirror option to be Disable Mirr or . ¾ St e p 2 : Click the Apply button to disable mirroring. 37 ...

  • Lindy 25010 - page 39

    2.9 QOS (Quality of Service) The 24G web smart switch provides up to four in ternal transmit queues per port to support four dif ferent traf fic priorities. The high-priority traffic experiences less delay in th e switch than that of lower priority traf fic under congested conditions. The 24G web smart switch provides three types of QOS. It can ass ...

  • Lindy 25010 - page 40

    2.9.1 Get/Refr esh the Latest QOS Settings Click the QOS menu on the web page. The QOS settings on the switch will be displayed. This is also the page to configure QOS. The following parameters are provided to be set:  Scheduling Method ¾ S trict Priority – to set this switch to transmit pa ckets with S trict Priority algorithm ¾ W eighted R ...

  • Lindy 25010 - page 41

    2.9.2 Enable QOS ¾ St e p 1 : Choose the Scheduling Method (ex: W eighted Round Robin). ¾ St e p 2 : Set Priority/Queue m ap (ex: Priority1, 2, 3 and 4 belong to Queue0, Priority4 and 5 belong to Queue1, Priority6 belong to Queue2, Priority7 belong to Queue4). ¾ St e p 3 : If Scheduling Method is W eighted Round R obin, assign a weight for every ...

  • Lindy 25010 - page 42

    2.9.3 Modify QOS Settings ¾ St e p 1 : Change the Scheduling Method to be S t rict Priority . ¾ St e p 2 : Change the Priority/Queue m ap (ex: Prirotiy0 belong to Queue3, Priority1, 2 and 3 belong to Queue2, Priority4, 5 and 6 belong to Queue1, and Priority7 belongs to Queue0). ¾ St e p 3 : Click the Apply button to modify QOS settings. 41 ...

  • Lindy 25010 - page 43

    2.10 Rate and S torm Contr ol T o provide more efficient system perform ance, the 24G web smart switch provides rate and storm control to limit the per -port traffic rate and to globally suppress the storm from unknown or broadcast frames received by the sy stem. 2.10.1 Rate Contr ol This system supports per - port rate control. When the incom ing ...

  • Lindy 25010 - page 44

    Select port number to setup the per -port rate control value. In the page of ingress rate limit, shown in the following figure (e.g. for Port2), select one (e .g. 8Mbps) of 14 dif ferent ra tes to lim it the rate or select “No Limit” to un-limit the rate f or this port. After clicking the Apply button to activate the setting, the previous page ...

  • Lindy 25010 - page 45

    2.10.2 St o r m C o n t r o l In the Rate Limit and S torm Contr o l page, the hyperlink (e.g. Disabled ) on the row with St o r m Control field shows the current setting of this function. This function will globally affect all ports in the system. Just click this hyperl ink to configure the setting. In the S torm Control page, there are 2 fields t ...

  • Lindy 25010 - page 46

     S torm Control Rate – this field provides 13 dif ferent control rates from 1fps (frames per second) to 15,000fps. This dropdown will be disabled while the S torm Contr ol T ype is disabled. After selecting the storm control t ype and rate, click the Apply button to activa te the settings for this function. The figure shown as below is an exam ...

  • Lindy 25010 - page 47

    2.11 System Setup The System Setup page provides the management inform ati on of the switch. This page, shown as below , can be activated by clicking the System Setup menu under the System section. The following parameters can be configured / displayed:  Model Name – the model nam e of this switch (read-only)  Chip V ersion – the switch c ...

  • Lindy 25010 - page 48

    2.11.1 Firmwar e Update The 24G web smart switch provides the facility to update firmware for new features, customized requests and system fault recovery . The page, sh own as below , can be activated by clicking the Update link on the System Setup page. This system supports both BOOTP/TFTP and pur e TFTP to update the firmware. The TFTP server IP ...

  • Lindy 25010 - page 49

    2.11.1.1 Firmware Update V ia TFTP Before proceeding with the firmware update, it is required to co rrectly prepare the TFTP server and the firmware file which will be uploaded to th e switch. (P lease refer to th e vendor’ s instruction guide for setting up the TFTP server you would like to use). When the TFTP server and the firmware file are r ...

  • Lindy 25010 - page 50

    2.11.1.2 Firmware Update V ia BOOTP/TFTP Before proceeding with the firmware update, it is required to co rrectly prepare the BOOTP / TFTP server and the firmwar e file which will be uploaded to th e switch. (Please refer to the vendor’ s instruction guide for setting up the TF TP server you would like to use). When the BOOTP/TFTP server and the ...

  • Lindy 25010 - page 51

    2.11.2 DHCP Client The IP address of the 24G web s mart switch ca n be statically assigned by manual entry or dynamically assigned by a DHCP server . 2.11.2.1 Assign a fixed IP address Change DHCP Client to be disabled. Enter a fixe d IP address, Subnet mask and Gateway , and then click the Apply button. 2.11.2.2 Assign an IP address by DHCP server ...

  • Lindy 25010 - page 52

    2.11.3 ARL Aging The 24G web smart switch supports aging timer for MA C address entry in the address table. If ARL aging is enabled and aging time is 300 seconds, ev ery MAC address entry learned from every front port will stay in the address table for 300 seconds . After 300 seconds, the switch will rem ove this MAC entry . Click ARL Aging to modi ...

  • Lindy 25010 - page 53

    2.12 User Management User management is used for m aintaining the us ername and password for login validation to access the switch. This switch provides one login account for configurat ion management. Just click the User Management menu to activate the User Management page as shown below:  New Username – to set the username string (max. 10 ch ...

  • Lindy 25010 - page 54

    2.13 Reset System This switch can be rebooted or reset to de fault configurations through the web page. Click Reboot System menu to reboot the system. Click Reset System menu to rese t the system back to factory settings. ¾ Reboot System – Just reboot the system. All configuration settings will be retained to the latest changes before the reboot ...

  • Lindy 25010 - page 55

    2.14 Command Line Interface (CLI) In addition to the web management, the 24G web smart switch also provides a serial interface (RS-232) as a console port on the rear panel to manage the switch for system setup, user management, reset system and firmware update s through the command line interface (CLI). W e recommend you use W indows Hyper T ermina ...

  • Lindy 25010 - page 56

     Help Menu Press “H”, “h” or “?” to show all management commands in the console.  Get System Information Press “IG” or “ig” to show m odel name and firmware version.  Get Current Network Settings Press “NG” or “ng” to show DHCP client status, system IP address, network mask, gateway and MAC address. 55 ...

  • Lindy 25010 - page 57

     Configur e Network Press “NS” or “ns” to co nfigure system network. If the user wants to assign this system an IP address by DHCP server , enter “Y” or “y” to start DHCP progress. . If the user wants to assign this system a fi xed IP address manually , please enter “N” or “n” to abort DHCP progress.  User Management T ...

  • Lindy 25010 - page 58

     Enable/Disable 802.1Q VLAN T ype “VE” or “ve” to enable or disable the 802.1Q VLAN function.  Get 802.1Q VLAN Enable Setting T ype “VF” or “vf” to show if 802.1Q VLAN function is enab led or disabled.  Set PVID T ype “VV” or “vv” to set per-port PVID in 802.1Q VLAN function. The PVID of admin port (port 25) in 802. ...

  • Lindy 25010 - page 59

     Upgrade Firmwar e V ia TFTP or BOO TP/TFTP T ype “UF” or “uf” to start the firm ware upgrade progress via TFTP server . Choose “ 1 ” to update firmware via TFTP . Enter the TFTP server IP address and firmware filename. Choose “ 2 ” to update the firmware via BOOTP/TFTP . Once the 24G web smart switch has rebooted, th e firmware ...

  • Lindy 25010 - page 60

     Reboot System After W rite Default T ype “RD” or “rd” to reset th e system to factory settings.  Logout T ype “LO” or “lo” to logout of the system. 59 ...

  • Lindy 25010 - page 61

    3 Specifications  Standards Compliance IEEE 802.3 10BaseT Ethernet IEEE 802.3u 100BaseTX Fast Ethernet IEEE 802.3ab 1000Base Gigabit Ethernet IEEE 802.3x flow control for half and full duplex IEEE 802.1q Tag-based VLAN  Interfaces 24 x 1000BaseTX RJ-45 connector ports, 2 mini-GBIC ports 1 RS-232 terminal port  Buffer Memory 512MB for packe ...

  • Lindy 25010 - page 62

     Power Input: 100-240VAC, 50/60Hz Power consumption: 40 Watts m ax.  Dimensions 440mm (W) × 184mm (D) × 44mm (H)  Weight 2.3 Kg  Electromagnetic Emissions: Class A FCC, CE, VCCI, C-Tick  Safety CB 61 ...

  • Lindy 25010 - page 63

    CE Conformity This equipment has been tested and found to co mply with the relevant European Community Directive 93/68/EEC for Electromagnetic Compa tibility for Information T echnology Equipment. FCC W a rning This equipment has been tested and found to comp ly with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. The ...

Manufacturer Lindy Category Switch

Documents that we receive from a manufacturer of a Lindy 25010 can be divided into several groups. They are, among others:
- Lindy technical drawings
- 25010 manuals
- Lindy product data sheets
- information booklets
- or energy labels Lindy 25010
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lindy 25010.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lindy 25010, service manual, brief instructions and user manuals Lindy 25010. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lindy 25010.

Similar manuals

A complete manual for the device Lindy 25010, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lindy 25010 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lindy 25010.

A complete Lindy manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lindy 25010 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lindy 25010, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lindy 25010, that we can find in the current document
3. Tips how to use the basic functions of the device Lindy 25010 - which should help us in our first steps of using Lindy 25010
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lindy 25010
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lindy 25010 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lindy 25010?

Use the form below

If you did not solve your problem by using a manual Lindy 25010, ask a question using the form below. If a user had a similar problem with Lindy 25010 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)