English dropdown-ico

Manual Stovax 8627 MA

28 pages 0.51 mb
Download

Go to site of 28

Summary
  • Stovax 8627 MA - page 1

    Riva Nemos Balanced Flue Convector Fire With upgradeable control valve Instructions for Use, Installation and Servicing For use in GB, IE (Great Britain and Eire) IMPORTANT Do not attempt to burn rubbish in this appliance. This appliance must only be operated with the glass door secured firmly in position. The front casing of this appliance will be ...

  • Stovax 8627 MA - page 2

    2 CONTENTS COVERING THE FOLLOWING MODELS 8627 MA P8627 MA 8627 BS P8627 BS PAGE APPLIANCE COMMISSIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Requirements 9 Installation 12 Commissioning 18 SERVICING INSTRUCTIONS 19 Servicing Requirements 19 Fault Finding 19 How to replace parts 21 Basic spare p ...

  • Stovax 8627 MA - page 3

    3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test N/A 3. Spillage test N/A GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full 4. Gas rate m 3 /h 5. Does ventilation meet appliance requirements N/A 6 ...

  • Stovax 8627 MA - page 4

    4 USER INSTRUCTIONS 1. GENERAL 1.1 A competent person must carry out installation and servicing. 1.2 In all correspondence, please quote the appliance type and serial number, which can be found on the databadge located on a plate under the control valve. 1.3 Ensure that curtains are not positioned above the appliance and there is at least 300mm bet ...

  • Stovax 8627 MA - page 5

    5 USER INSTRUCTIONS 5. CLEANING THE NEMOS ENSURE THE APPLIANCE IS COLD BEFORE PROCEEDING. 5.1 The outside casing of the Nemos should be cleaned using a damp cloth. If you have a stainless steel door version, it should be cleaned using a stainless steel cleaner. 5.2 To clean the burner system, firstly depress the front door centrally on the RH side ...

  • Stovax 8627 MA - page 6

    7 AR1197 6.6 Place log F resting on the rear tray and leaning forward to locate in the recess in log E. See diagram 8. AR1198 8 6.7 Place log G at the front of the fire between logs D and E. DO NOT PLACE THIS LOG ON THE BURNER. IT IS ONLY TO FILL THE GAP BETWEEN LOGS D AND E. The charred effect should face the rear of the fire. See diagram 9. AR119 ...

  • Stovax 8627 MA - page 7

    7 USER INSTRUCTIONS 10 AR1120 6.9 Ensure that the fibreglass seal on the back of the glass frame is intact then hook the location tabs over the hooks on the top of the firebox. Replace the nine screws working from the top down. Tighten the screws evenly. DO NOT OVER TIGHTEN. See diagram 2, section 5 "Cleaning the Nemos" NEVER OPERATE THE ...

  • Stovax 8627 MA - page 8

    8 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION COVERING THE FOLLOWING MODELS: 8627 MA P8627 MA 8627 BS P8627 BS PACKING CHECKLIST Qty Description 1 Nemos stove assembly 1 Ceramic back panel * 1 Ceramic LH side panel * 1 Ceramic RH side panel * 1 Log set (7 logs) 1 Bag of Granules 1 Decorative Cast Collar 1 Fixing kit containing: 1 Instruction ...

  • Stovax 8627 MA - page 9

    9 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1. FLUE AND CHIMNEY REQUIREMENTS NOTE: This appliance can only be installed in conjunction with the flue supplied. 1.1 The flue must be sited in accordance with all local and national regulations and current rules in force. 1.2 Any terminal which is less than 2 metres above any access (level ground, bal ...

  • Stovax 8627 MA - page 10

    10 1C AR1673 2.1 TOP FLUE UP & OUT KIT (8534/8534AN) Vertical from the top of the appliance then horizontally out. (See diagram 1A). The basic kit comprises: 1 x 200mm vertical length 1 x 500mm terminal length (cut to length on site) 1 x 90 degree elbow 1 x wall plate 1 x 70mm restrictor 1 x 60mm restrictor fixing screws The kit may be used on ...

  • Stovax 8627 MA - page 11

    11 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 4. VENTILATION 5. APPLIANCE LOCATION 4.1 This appliance requires no additional ventilation. 5.1 It is not necessary to site the appliance on a non- combustible floor. However, for practical reasons, the floor should be flat and solid to allow the appliance to be levelled and secured in place. 5.2 This ...

  • Stovax 8627 MA - page 12

    12 IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO RELIGHT THE APPLIANCE. 3. INSTALLATION OF THE APPLIANCE NOTE: THERE IS AN OPTIONAL CONVECTION FAN KIT AVAILABLE CODE No. 8576. THIS CAN BE FITTED EITHER DURING OR AFTER INSTALLATION, BUT PROVISION FOR A POWER SUPPLY MUST BE MADE PRIOR TO INSTALLATION OF THE ...

  • Stovax 8627 MA - page 13

    3.3 Remove the lower front panel by gripping the top tag and pulling gently upwards and out. Locate the two bolts securing the appliance to the crate base and remove. See diagram 3. AR1290/1 3 3.4 Gently remove the appliance from the crate and place into its intended position. Locate the two securing holes in the base subframe (those previously use ...

  • Stovax 8627 MA - page 14

    3.9 Before any flue pipe is attached to the appliance, unwrap the decorative cast iron collar and locate over the outer flue spigot ensuring that the location lug locates in the notch at the rear of the hole. See diagram 7. 7 AR1293 3.10 When installing the horizontal terminal, decide on the terminal position and measure the height from the top of ...

  • Stovax 8627 MA - page 15

    3.16 It is now necessary to connect the gas supply to the appliance. The gas supply may enter through the floor directly under the appliance or through the knockout panel in the rear RH corner of the outer casing. In both instances, a preformed pipe is ready fitted and connection should be made to the compression fitting on the end of this pipe. Se ...

  • Stovax 8627 MA - page 16

    16 4. ARRANGEMENT OF FUEL BED COMPONENTS ADVICE ON HANDLING AND DISPOSAL OF FIRE CERAMICS The fuel effect and side panels in this appliance are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application. Protective clothing is not required when handling these articles, but we recommend you follow normal hygiene ...

  • Stovax 8627 MA - page 17

    17 INSTALLATION INSTRUCTIONS INSTALLATION AR1198 8 4.7 Place log G at the front of the fire between logs D and E. DO NOT PLACE THIS LOG ON THE BURNER. IT IS ONLY TO FILL THE GAP BETWEEN LOGS D AND E. The charred effect should face the rear of the fire. See diagram 9. AR1199 9 4.8 With the granules fill the front compartment around the logs evenly. ...

  • Stovax 8627 MA - page 18

    18 6. LIGHTING THE NEMOS 6.1 Locate the control valve on the appliance. There are two control knobs on the valve, the right hand knob controls the pilot ignition and the left hand knob controls the main burner. 6.2 If your appliance has already been upgraded to battery remote control, please refer to the instructions provided with the upgrade to op ...

  • Stovax 8627 MA - page 19

    19 SERVICING INSTRUCTIO NS SERVICING / FAULT FINDING CHARTS IGNITION FUNCTIONAL CHECK 1 PILOT WILL NOT LIGHT Ensure there is no debris around the pilot assembly, (e.g. soot, etc.) which could short the spark, clean the area. Operate the valve. Is there a spark? Consult User Instructions and retry. Check alignment of pilot burner head, change the ig ...

  • Stovax 8627 MA - page 20

    20 SERVICING INSTRUCTIO NS FAULT FINDING CHARTS PILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USE Ensure there is no debris around the pilot assembly, (e.g. soot etc.) Check for fluff in the pilot aeration hole. See diagram 5 in Replacing Parts, section 2.3. Problem is with the pipe work or fittings which lead to the fire. Correct and retry. Is therm ...

  • Stovax 8627 MA - page 21

    21 2.3 Remove the ceramic logs and the embers. 2.4 Carefully slide the ceramic sides forward and store safely. See diagram 3. 3 AR0759 2.5 Remove the screws from the log support. The feed pipe nut is now visible between the burner and the angled base of the firebox. See diagram 4, arrow A. AR0818 4 2.6 Undo the feed pipe nut and the four screws hol ...

  • Stovax 8627 MA - page 22

    22 3. PILOT UNIT The pilot assembly consists of four components, which can be individually changed, these are: 1) Pilot burner bracket. 2) Pilot injector 3) E l e c t r od e 4) Thermocouple. 3.1 Open the front door of the appliance and turn off the gas supply at the isolating device. Remove the glass frame and logs. 3.2 Remove the two screws securi ...

  • Stovax 8627 MA - page 23

    23 d) Remove the external feed pipe from the brass fitting. See diagram 8 arrow B. e) Remove the 2 screws fixing the valve bracket to the base of the appliance. f) Gently slide the gas valve and bracket forward and disconnect the thermocouple from the rear of the gas valve. See diagram 9, arrow A. 9 AR0824 g) Push the thermocouple down through the ...

  • Stovax 8627 MA - page 24

    24 6.3 Remove the two screws retaining the valve bracket. See diagram 12. 12 AR0822 6.4 Remove the ignition lead as described in section 4. 6.5 The valve should now be able to be eased forward so the pipes and thermocouple can be removed from the rear of the valve. 6.6 Undo the two screws retaining the valve to the bracket. 6.7 Replace in reverse o ...

  • Stovax 8627 MA - page 25

    12. SHORT SPARES LIST COMPONENT NG LPG PILOT INJECTOR PI0026 PI0015 MAIN INJECTOR IN0029 IN0051 AERATION PLATE NATURAL GAS G20 GZ2025 BURNER UNIT GZ3964 AERATION PLATE LPG G30 G31 GZ3865 GZ2003 BURNER UNIT GZ3965 GAS VALVE* GC0088 THERMOCOUPLE PI0063 MAG UNIT GC0092 IGN LEAD GC0090 SPARK ELECTRODE PI0053 REAR CERAMIC PANEL CE0388 L/H CERAMIC PANEL ...

  • Stovax 8627 MA - page 26

    26 SERVICE RECORDS 1ST SERVICE 2ND SERVICE Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: ................................. Next Service due: ............................... N e x t S e r v i c e d u e : ............................... Signed: ....................................... S i g n e d : . ...

  • Stovax 8627 MA - page 27

    27 ...

  • Stovax 8627 MA - page 28

    Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group ...

Manufacturer Stovax Category Indoor Fireplace

Documents that we receive from a manufacturer of a Stovax 8627 MA can be divided into several groups. They are, among others:
- Stovax technical drawings
- 8627 MA manuals
- Stovax product data sheets
- information booklets
- or energy labels Stovax 8627 MA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stovax 8627 MA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stovax 8627 MA, service manual, brief instructions and user manuals Stovax 8627 MA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stovax 8627 MA.

Similar manuals

A complete manual for the device Stovax 8627 MA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stovax 8627 MA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stovax 8627 MA.

A complete Stovax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stovax 8627 MA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stovax 8627 MA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stovax 8627 MA, that we can find in the current document
3. Tips how to use the basic functions of the device Stovax 8627 MA - which should help us in our first steps of using Stovax 8627 MA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stovax 8627 MA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stovax 8627 MA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stovax 8627 MA?

Use the form below

If you did not solve your problem by using a manual Stovax 8627 MA, ask a question using the form below. If a user had a similar problem with Stovax 8627 MA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)