English dropdown-ico

Manual Delta Electronics DNL Series

20 pages 0.5 mb
Download

Go to site of 20

Summary
  • Delta Electronics DNL Series - page 1

    Evaluation Procedure (DEP-002 A) The Delphi DNM and DNL Series of SMT type POL converters The DNM and DNL, 2.4~5.5V or 10~14V input, programmable output, non-isolated point of load DC/DC converters, are the latest of fering from one of the world’s largest power supply manufacturers ― Delta Electronics, Inc. The DNM and DNL product family also h ...

  • Delta Electronics DNL Series - page 2

    2 3.0 Equipment Required 3.1 A DC Power Supply 0 - 20 V @ 0 - 20A (Agilent 6574A 0 -60V/0 - 35A or equivalent). 3.2 An oscilloscope (T ektronix TDS 3034 or equivalent) 4 Channel 300 MHz, equipped with a x1 scope probe, a x10 scope probe, and two BNC cables (length less than 20 inches/500mm) 3.3 Digital m ulti-meters, one with 20A range and ideally ...

  • Delta Electronics DNL Series - page 3

    3 4.1 Connect one lead from the “+” lead of the DC source (S ee Item 3.1) to the “20A” terminal of the first multi-meter DVM1 (See Item 3.3). Then connect one lead from the “Common” of the DVM1 to the “Vin” pin of the Evaluation Board. DVM1 is used to measure the input current. 4.2 Connect one wire from the “-” lead of the DC so ...

  • Delta Electronics DNL Series - page 4

    4 6.0 T est s Performed The following tests are p erformed at room temperature (+25 ℃ ). 6.1 Input Characteristics  Input V oltage Range.  Under-V oltage Lockout.  No Load Input Current. 6.2 Output Characteristics  Line Regulation.  Load Regulation.  Output Regulation.  Output V oltage Set-point Programming  Output V oltag ...

  • Delta Electronics DNL Series - page 5

    5 5) SW2 is used to enable or disable the converter . For positive logic module, When SW2 is pose for the ON position, the converter is ON, and SW2 is pose for the OFF position, the converter is OFF . For negative logic module, When SW2 is pose for the ON position, the converter is OFF , and SW2 is pose for the OFF position, the converter is ON. 6) ...

  • Delta Electronics DNL Series - page 6

    6 8.0 T est s and Evaluation 8.1 Input Characteristics 8.1.1 Input V olt age Range and Under-V oltage Lockout The DNM04xx and DNL04xx Series of DC/DC converters will operate at full load from 2.4Vin to 5.5Vin for 5Vin (nominal) types. The DNM12xx and DNL12xx Series DC/DC converters will operate at full load from 10V in to 14V in for 12V in (nominal ...

  • Delta Electronics DNL Series - page 7

    7 8.2 Output Characteristics 8.2.1 Line Regulation Line Regulation Deviation is defined as the change in output volt age caused by varying the input voltage over a specified range while the ou tput load and temperature remain const ant. T est 1) T urn on the fan. 2) Set the output power to the desired operating point. 3) Set the switch SW2 to the c ...

  • Delta Electronics DNL Series - page 8

    8 8.2.4 Output V oltage Set-point Programming (1) Output V olt age Set-Point Ad justment by external resistor Output V oltage Set-point Programming can be carried out by using the extern al program resistor connect between TRIM pin to ground to set output volt age set-point from 0.75Vdc to 5Vdc, the location can refer to the Evaluation Board Schema ...

  • Delta Electronics DNL Series - page 9

    T able 2. Vo , s e t Rset (k Ω ) R33 Recommend Value, R//R 0.7525 Open Open 1.2 22.464 23.7k//432k 1.5 13.047 14.0k//191k 1.8 9.024 9.53k//169k 2.5 5.009 5.23k//118k 3.3 3.122 3.16k//261k 5.0 1.472 1.5k//78.7k T est 1. Put the resistor to program the desired output voltage set point by follow T able 1 and T able 2 for the standard output. 2. Set ...

  • Delta Electronics DNL Series - page 10

    For DNM12xx and DNL12xx series () 7525 . 0 0667 . 0 7 . 0 − × − = Vout Vtrim V For example, to program the output voltage of a DNL12S module to 3.3 Vdc, Vtrim is calculated as follows () 53 . 0 7525 . 0 3 . 3 0667 . 0 7 . 0 = − × − = Vtrim V T able 4. : V o,set adjustm ent range using external voltage source. Product Part Normal Output Se ...

  • Delta Electronics DNL Series - page 11

    11 8.2.6 Voltage Tracking The DNM/DNL family was designed for applications that have output voltage tracking requirements during power-up and power-down. The devices have a TRACK pin to implement three types of tracking method: sequential, ratio-metric and simultaneous. TRACK simplifies the task of supply voltage tracking in a power system by enabl ...

  • Delta Electronics DNL Series - page 12

    12 Figure 4: Sequential Power up Figure 5: Sequential Power down Ratio-Metric Implementation Ratio–metric is implemented by the selection of the resistor values of the voltage divider on the TR A CK pin. Resistors R1 and R2, in Figure 6 determine the tracking met hod that is implemented. To simplify the tracking design, set the initial value of R ...

  • Delta Electronics DNL Series - page 13

    For Ratio-Metric applications that need the outputs of PS1 and PS2 achieve the regulation set point at same time, use equation 1 to calculate R1, set △ V=Vo set,PS1 –Vo set,PS2 and △ V will b e negative. The waveforms of power up and down are showed in Figures 7 and 8. K Vref Vref V Vo R PS set 20 * ] ) [( 1 2 , − ∆ + = Ω -------------- ...

  • Delta Electronics DNL Series - page 14

    14 For example, the PS1 Vo set,PS1 =5V, the PS2 Vo set,PS2 =3.3V, R1 is calculated as follows: K K R 303 . 10 20 * 32 . 1 ] 32 . 1 ) 3 . 1 3 . 3 [( 1 = − − = Ω Figure 9. Ratio–metric tra cking Power up Figure 10. Ratio–metric tracking Power down Simultaneous Implementation Similar to the ratio-metric implementation, simultaneous tracking ...

  • Delta Electronics DNL Series - page 15

    15 For type C (DNXXX0A0XXXX C ), th e simultaneous tracking can be accomplished by putting R1 equal to 30.1K Ω through Vo PS1 to the TRACK pin of PS2. Figure 12 shows the circuit diagram of Simultaneous start-up when Vo PS2 tracks the Vo PS1 (only for type C). R1 R2 TRACK Vo PS1 PS2 Vo PS2 PS1 Vin Vin ENABLE ENABLE To Tracking circuit 20K 30.1K Fi ...

  • Delta Electronics DNL Series - page 16

    16 Notes on the use of Track function: 1. For proper voltage tracking, first, The ENABLE On/Off pin of the PS2 module is lef t unconnected (or tied to GND for negative logic modules or tied to VIN for positive logic modules), so that the modules are ON by default and second applied input voltage to the PS1 and PS2. The TRACK pin is held at ground p ...

  • Delta Electronics DNL Series - page 17

    T est 1) T urn on the fan. 2) Adjust the input voltage to the desired operating point. 3) Set the electronic or resistive load at 50% of maximum load. 4) Change channel 1 to scope probe and measure across the dynamic R . 5) Set the switch SW2 to the converter ON. 6) Set channel 2 on the oscillo scope to be AC coupled and to 50mV/Div and for 5mS/Div ...

  • Delta Electronics DNL Series - page 18

    4. Connect a scope probe from channel 1 between the on/off control pin and re ference ground (SGND) on the Evaluation Board. 5. Set channel 2 on the oscilloscope to be DC coupled and to the appropriate range for the output voltage. 6. Connect a coaxial cable from channel 2 to BNC2 on the Evaluation Board. 7. Set the T ime base to 2mS/Div 8. Set the ...

  • Delta Electronics DNL Series - page 19

    Appendix A- Evaluation Board Schematic 19 ...

  • Delta Electronics DNL Series - page 20

    Appendix B - Evaluation Board Layout (Top View) Appendix C - Evaluation Board Layout (Bottom View) CONTACT DATA: www. de l ta ww. c om USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com Europe: Telephone: France: +33 1 6485 1212 Germany: +49 89 370 62 897 UK: +44 777 195 6299 Fax: +3 ...

Manufacturer Delta Electronics Category Power Supply

Documents that we receive from a manufacturer of a Delta Electronics DNL Series can be divided into several groups. They are, among others:
- Delta Electronics technical drawings
- DNL Series manuals
- Delta Electronics product data sheets
- information booklets
- or energy labels Delta Electronics DNL Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta Electronics DNL Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta Electronics DNL Series, service manual, brief instructions and user manuals Delta Electronics DNL Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta Electronics DNL Series.

Similar manuals

A complete manual for the device Delta Electronics DNL Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta Electronics DNL Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta Electronics DNL Series.

A complete Delta Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta Electronics DNL Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta Electronics DNL Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta Electronics DNL Series, that we can find in the current document
3. Tips how to use the basic functions of the device Delta Electronics DNL Series - which should help us in our first steps of using Delta Electronics DNL Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta Electronics DNL Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta Electronics DNL Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta Electronics DNL Series?

Use the form below

If you did not solve your problem by using a manual Delta Electronics DNL Series, ask a question using the form below. If a user had a similar problem with Delta Electronics DNL Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)