English dropdown-ico

Manual Newland EM1300

136 pages Not applicable
Download

Go to site of 136

Summary
  • Newland EM1300 - page 1

    NLS-EM1300 1D Barcode Scanning Engine Integration Guide V ersion 1.0 ...

  • Newland EM1300 - page 2

    nlscan.com Page 2 V ersion Description Date Pre-release Initial release 26-08-2009 V ersion 1.0 Support as from EM1300 fi rmware V ersion 1.13.7 and higher . 20-05-2010 Revisions ...

  • Newland EM1300 - page 3

    Disclaimer © 1999-2008 by Newland Auto-ID T ech. Co., Ltd, All rights reserved. No part of this publication may be reproduced, transmitted, or used in any form or by any means, electrical or mechanical, without prior written permission from Newland Auto-ID. The material in this manual is subject to change without notice. All software, including ? ...

  • Newland EM1300 - page 4

    nlscan.com Page I 请更换节标题 T able of Contents Content About this guide Introduction ................................................................................................................................................. 1 Chapter Description ........................................................................................ ...

  • Newland EM1300 - page 5

    nlscan.com Page II T able of Contents EM1300 Development T ools Introduction ................................................................................................................................................ 19 EM1300 Evaluation Kit, EVK3000&1300 ..................................................................................... ...

  • Newland EM1300 - page 6

    nlscan.com Page III T able of Contents Disable or Enable User Pre fi x ............................................................................................................. 48 Program User Pre fi x ........................................................................................................................... 48 AIM Pre fi x . ...

  • Newland EM1300 - page 7

    nlscan.com Page IV T able of Contents ISBN .......................................................................................................................................................... 67 Load Factory Default .......................................................................................................................... 67 En ...

  • Newland EM1300 - page 8

    nlscan.com Page V T able of Contents Matrix 25 Code ID .............................................................................................................................. 86 Check Digit ........................................................................................................................................ 87 Select Messag ...

  • Newland EM1300 - page 9

    nlscan.com Page VI T able of Contents MSI-Plessey .............................................................................................................................................. 11 2 Load Factory Default ......................................................................................................................... 11 2 Enab ...

  • Newland EM1300 - page 10

    nlscan.com Page 1 About this guide Introduction This NLS-EM1300 ( “ EM1300 ” ) Scan Engine Integration Guide provides general instructions for OEM integration. Chapter Description About EM1300: The chapter of About EM1300 gives a brief description of the EM1300. It covers the general, overall speci fi cations of the EM1300. Mechanical Interfac ...

  • Newland EM1300 - page 11

    nlscan.com Page 2 About this guide Newland Auto-ID Support Center If you have a problem with your equipment, contact the Newland Support Center in your region. Before call- ing, have the model number , serial number , and several of your barcodes at hand. Call the support Center from a phone near the scanning equipment so that the service person ca ...

  • Newland EM1300 - page 12

    nlscan.com Page 3 About EM1300 Introduction EM1300 is an embedded barcode reading engine. Its gray scale CCD image capturer and the Newland patented UIMG, a Computerized Image Recognition System, ensure the fast scanning and decoding accuracy on different barcode media such as paper , plastic card, and metal surface. It can be easily integrated int ...

  • Newland EM1300 - page 13

    nlscan.com Page 4 About EM1300 Get Familiar W ith EM1300 Unpacking Remove EM1300 and accessories from the package. Check for missing parts and inspect for damage. EM1300 is packed in anti-static bag. Please handle accordingly . Outline of EM1300 The outline of EM1300 is shown in Figure 1. The topside has the electrical control components, including ...

  • Newland EM1300 - page 14

    nlscan.com Page 5 About EM1300 EM1300 Decode Zone 42 ° 90mm Code 39(5mil) 195mm 0 100 200 300 400 500 50mm Code 39(10mil) 325mm 60mm EAN-13(10mil) 265mm 65mm EAN-13(15mil) 350mm 30mm Code 128(10mil) 285mm ...

  • Newland EM1300 - page 15

    nlscan.com Page 6 About EM1300 EM1300 Overall Speci fi cations Performance Interface TTL232 Image Sensor CCD Resoluing 2500 Scan Rate up to 300 scans/sec Decode Rate 200 decodes/sec (default) Symbologies Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar , Interleaved 2 of 5, ISBN/ISSN, Code 93, etc. Precision ≥ 5mil (Condition:PCS=0.9, testi ...

  • Newland EM1300 - page 16

    nlscan.com Page 7 Introduction Mechanical Interface This section describes theMechanical Interface. ...

  • Newland EM1300 - page 17

    nlscan.com Page 8 Mechanical Interface Dimensions of EM1300 Unit EM1300 Front V iew Following fi gures show the dimensions of EM1300. The fi gure 2 is EM1300 Front V iew . EM1300 Front V iew Figure 2. EM1300 Left Side V iew The Figure 3 is EM1300 Left Side V iew . EM1300 Left Side V iew Figure 3. EM1300 Bottom V iew The fi gure 4 EM1300 Bottom V ...

  • Newland EM1300 - page 18

    nlscan.com Page 9 Mechanical Interface Interface Interface Socket EM1300 uses a 12-pins fl ex cable socket to interface with external device (Host), such as EVK3000&1300, the EM1300 Evaluation Kit. Figure 5 below shows the socket. For reference purpose, the EM1300 Evaluation Kit uses a connector to connect the fl ex cable. Interface Socket Fi ...

  • Newland EM1300 - page 19

    nlscan.com Page 10 Mechanical Interface Interface Pin T ype I/O* Description PIN 1 Flash Download I Operation Mode Control: Flash Download Mode – Level Low when engine is » powered on; Normal Mode – otherwise. » If useres don ’ t need the function, it can be not connected(N/C). Pin 2 VCC P DC 3.3 ± 0.3V Pin 3 Ground GND Ground Pin 4 TXD O ...

  • Newland EM1300 - page 20

    nlscan.com Page 1 1 Mechanical Interface Interface Schematic of Interface Socket Unit ： mm 0 5 . 11 6 . 0 2 . 5 6 8 . 4 3 8 . 5. 5 2 . 0 ...

  • Newland EM1300 - page 21

    nlscan.com Page 12 Mechanical Interface Interface Interface Flexible Cable Speci fi cations The interface fl exible cable is designed by Newland Auto-ID. 03 . 05 . 55 . Unit ： mm ...

  • Newland EM1300 - page 22

    nlscan.com Page 13 Mechanical Interface Housing Design Considerations Housing Structure The housing for the Engine should make sure that no pressure should be put on the Engine. There should have suf fi cient space for the fl exible cable and stress release of the cable should also be considered. Scan W indow A scan window is needed to protect ca ...

  • Newland EM1300 - page 23

    nlscan.com Page 14 Electrical Interface Introduction This section describes the electrical speci fi cations of the interface signals. ...

  • Newland EM1300 - page 24

    nlscan.com Page 15 Electrical Interface Interface Signal levels The table below lists the interface input and output level voltage ranges Signal T ype V oltage Level V oltage Range Input High 2.4V - 3.6V Low -0.3V - 0.6V Output High 2.9V - 3.3V Low 0V - 0.4V ...

  • Newland EM1300 - page 25

    nlscan.com Page 16 Electrical Interface Input signals When the T rigger line is pull low for 10 ms, the Engine starts a read. The Engine keeps reading until a successful reading, a timeout or the line is high. After a successful reading, the line must go high in order to make another read. Here is a schematic from the evaluation board, EVK3000& ...

  • Newland EM1300 - page 26

    nlscan.com Page 17 Electrical Interface Output Signals Here are the descriptions of the output signals, such as Beeper , LED and inter-character timeout. They can be used to detect the status of the scanning, message uploading and the state of the Engine. LED Output When the Engine completes the initialization, the LED line is high. The LED line go ...

  • Newland EM1300 - page 27

    nlscan.com Page 18 Electrical Interface Output Signals A Sample Schematic of LED Circuit Here is the LED circuit used in the evaluation board, EVK3000&1300. R1 3 1K R1 4 100 K DGN D D5 GL ED R1 7 10 R DL ED DV 3. 3V Q4 2N 390 6 A Sample Schematic of Beeper Circuit Here is a beeper circuit used in the evaluation board, EVK3000&1300. DG ND BU ...

  • Newland EM1300 - page 28

    nlscan.com Page 19 EM1300 Development T ools Introduction Sections below list some EM1300 development tools. A brief introduction to each tool is included. ...

  • Newland EM1300 - page 29

    nlscan.com Page 20 EM1300 Development T ools EM1300 Evaluation Kit, EVK3000&1300 Here is a brief introduction to the EM1300 Evaluation Kit, EVK3000&1300. The layout of the EVK3000&1300 circuit board is shown in fi gure below . The board contains beeper , LED and trigger button. A USB connector and an alternative RS232 is for communicat ...

  • Newland EM1300 - page 30

    nlscan.com Page 21 Introduction There are 2 ways to program (con fi gure) the Engine, Code Programming and Command Programming. Code Programming The Engine reads a set of specially encoded barcodes to program options and features. In the following sections, we will explain the options and features available and provide the barcodes to program them ...

  • Newland EM1300 - page 31

    nlscan.com Page 22 General Programming General Programming T ools Code Programming ON Code Programming OFF Programming Notation Th i s is th e n ot at i on t o d is a bl e t he C o de P r og ra m mi ng . Th e re a r e 3 p ar ts of a no ta t io n: The barcode for Code Programming 1 、 The name of the options or features, such as Disable Code Progra ...

  • Newland EM1300 - page 32

    nlscan.com Page 23 General Programming General Programming T ools Code Programming ON Code Programming OFF Code Programming Re a d th e “ Co d e Pr o gr am m in g O N ” b a rc od e t o a ct iv a te “ C od e P ro gr a m- mi n g ” f u nc ti o n. M o re t h an o n e Co d e Pr o gr am m in g b ar co d es c a n be re ad to co n fi gu r e th e E ...

  • Newland EM1300 - page 33

    nlscan.com Page 24 General Programming Command Programming Commands under RS232 connection mean using 0x20-0x7D （ the displayable characters ） to express all commands information. Con fi guration State 1 、 The engine should be in con fi guration state when programming functions under RS232 connection. In the state, the engine would only acc ...

  • Newland EM1300 - page 34

    nlscan.com Page 25 General Programming Command Programming 3 、 F lo w C ha rt Non-Con fi guration State Con fi guration State Host sends “ $$$$ ” and receives “ @@@@ ” 5 seconds timeout ， receives “ ^^^^ ” Host sends “ %%%% ” and receives “ ^^^^ ” Host sends commands ， such as “ #XXXX ; ” Executing Commands Receives ...

  • Newland EM1300 - page 35

    nlscan.com Page 26 General Programming General Programming T ools Code Programming ON Code Programming OFF Default Factory Default Read “ Load All Factory Default ” to reset all parameters to factory default. Applicable conditions: Us e r op t io ns pr og r am mi n g wr o ng c o nf ig u ra ti o n le a ds t o r ea d in g m al - » fu n ct io n F ...

  • Newland EM1300 - page 36

    nlscan.com Page 27 General Programming General Programming T ools Code Programming ON Code Programming OFF W orking Mode Shut Down 1 【 Pro CMD ： 99900100 】 Deep Sleep 2 【 Pro CMD ： 99900101 】 Sleep 3 【 Pro CMD ： 99900102 】 T est Mode 4 【 Pro CMD ： 99900103 】 Restart 【 Pro CMD ： 99900104 】 Note: The 1 、 engine couldn? ...

  • Newland EM1300 - page 37

    nlscan.com Page 28 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Hand-held Mode Factory Default, scan engine will begin to scan when triggered. And when it scans successfully or the trigger is released, the engine will stop scanning. Hand-held Mode 【 Pro CMD ： 999001 10 】 Reading a barcod ...

  • Newland EM1300 - page 38

    nlscan.com Page 29 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Auto Mode First program the engine, then trigger it, the engine will start to scan. After a scan, the engine will not stop but start a new one automatically until another trigger. By default, the engine will not repeat reading a s ...

  • Newland EM1300 - page 39

    nlscan.com Page 30 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Interval Mode After programming, the engine will start interval scan without trigger . The interval between two scans is fi xed whether the scan is successful or not. The value of interval could be programmed by user and the defa ...

  • Newland EM1300 - page 40

    nlscan.com Page 31 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Sensor Mode After programming, the engine will start to sense the environment without trigger . After a scan, it will stop and keep sensing to wait another illumination changing. In sensor mode, a trigger also can start a scan. Th ...

  • Newland EM1300 - page 41

    nlscan.com Page 32 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Continuous Mode 【 Pro CMD ： 999001 14 】 Continuous Mode After programming, the engine will be in continuous mode without trigger . After a successful scan ， the engine will be in waiting state until another scan, then wait ...

  • Newland EM1300 - page 42

    nlscan.com Page 33 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Delayed Sensor Mode After programming, the engine will start to sense the environment without trigger . There will be a delay before a scan. After a scan, it will stop and keep sensing to wait another illumination changing. In del ...

  • Newland EM1300 - page 43

    nlscan.com Page 34 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Command T riggered Mode After programming, when HR100 receives trigger sweep command from terminal （ e.g. PC ） , then the device is begun working. PS: If the scan is completed then should be returned a value and automatic shut ...

  • Newland EM1300 - page 44

    nlscan.com Page 35 General Programming General Programming T ools Code Programming ON Code Programming OFF Security Level Security Level 1 【 Pro CMD ： 99900120 】 Security Level 2 【 Pro CMD ： 99900121 】 Security Level 3 【 Pro CMD ： 99900122 】 Security Level 4 【 Pro CMD ： 99900123 】 The higher the value of Security Level is, t ...

  • Newland EM1300 - page 45

    nlscan.com Page 36 General Programming General Programming T ools Code Programming ON Code Programming OFF Beeper No Beeper Output 【 Pro CMD ： 99900130 】 High Frequency & Loud V olume 【 Pro CMD ： 99900131 】 High Frequency & Medium V olume 【 Pro CMD ： 99900132 】 High Frequency & Low V olume 【 Pro CMD ： 99900133 】 ...

  • Newland EM1300 - page 46

    nlscan.com Page 37 General Programming General Programming T ools Code Programming ON Code Programming OFF Others Start/Stop Analog Trigger Start Analog T rigger 【 Pro CMD ： 99900035 】 StopAnalog T rigger 【 Pro CMD ： 99900036 】 Start/Stop T emporary Mute Start T emporary Mute 【 Pro CMD ： 99900040 】 Stop T emporary Mute 【 Pro CMD ...

  • Newland EM1300 - page 47

    nlscan.com Page 38 Query Command Introduction After reading interrelated programming barcodes, the engine will feed information needed back to the Host to achieve the purpose of query . Query Product Information 【 Pro CMD ： 99900300 】 Query Hardware V ersion 【 Pro CMD ： 99900301 】 Query Product ID 【 Pro CMD ： 99900302 】 Query Manu ...

  • Newland EM1300 - page 48

    nlscan.com Page 39 Communication Programming Introduction Under TTL232 connection the engine and the Host use the same communication parameters: baud rate, parity check, data bits select and stop bits select. ...

  • Newland EM1300 - page 49

    nlscan.com Page 40 Serial Port Programming Communication Setup Under TTL232 connection, the engine and the Host should set communication baud rate to the same to keep normal communication. Baud rate is the bits transmitted per second (8 bits per bytes). The engine and the Host must communicate at the same baud rate. The reader supports baud rate as ...

  • Newland EM1300 - page 50

    nlscan.com Page 41 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Check ** No Check 【 Pro CMD ： 99902120 】 Odd Check 【 Pro CMD ： 99902121 】 Even Check 【 Pro CMD ： 99902122 】 ...

  • Newland EM1300 - page 51

    nlscan.com Page 42 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Stop Bit ** 1 Stop Bit 【 Pro CMD ： 99902131 】 2 Stop Bit 【 Pro CMD ： 99902133 】 ...

  • Newland EM1300 - page 52

    nlscan.com Page 43 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Flow Control ** No Flow Control 【 Pro CMD ： 99902140 】 ...

  • Newland EM1300 - page 53

    nlscan.com Page 44 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Data Bit ** 8 Data Bit 【 Pro CMD ： 99902150 】 8 Data Bit, No Check, 1 Stop Bit 【 Pro CMD ： 99902160 】 8 Data Bit, Even Check, 1 Stop Bit 【 Pro CMD ： 99902161 】 8 Data Bit, Odd Check, 1 Stop ...

  • Newland EM1300 - page 54

    nlscan.com Page 45 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming 7 Data Bit 【 Pro CMD ： 99902151 】 7 Data Bit, Even Check, 1 Stop Bit 【 Pro CMD ： 99902166 】 7 Data Bit, Odd Check, 1 Stop Bit 【 Pro CMD ： 99902167 】 7 Data Bit, Even Check, 2 Stop Bit 【 P ...

  • Newland EM1300 - page 55

    nlscan.com Page 46 Data Format Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters. However , in reality , they do not and should not have enough information we need, such as barcode type, date and time of scan, delimiter , and so on ...

  • Newland EM1300 - page 56

    nlscan.com Page 47 Data Format Data Format T ools Code Programming ON Code Programming OFF Pr e fi x S eq ue n ce s CodeID+User Pre fi x+AIMID 【 Pro CMD ： 99904010 】 User Pre fi x+CodeID+AIMID 【 Pro CMD ： 9990401 1 】 ...

  • Newland EM1300 - page 57

    nlscan.com Page 48 Data Format Data Format T ools Code Programming ON Code Programming OFF User Pre fi x User Pre fi x is added before barcode message. For example, if the user pre fi x is “ AB ” and the barcode message is “ 123 ” , the Host receives “ AB123 ” . Program User Pre fi x En a bl e “ P ro g r am Us e r P re f ix ” . ...

  • Newland EM1300 - page 58

    nlscan.com Page 49 Data Format Data Format T ools Code Programming ON Code Programming OFF AIM Pre fi x AIM (Automatic Identi fi cation Manufactures) de fi nes AIM pre fi x for many standard barcode formats. The engine will add the identi fi er before the barcodes. And this identi fi er is the AIM Pre fi x. And please see Appendix to fi nd ...

  • Newland EM1300 - page 59

    nlscan.com Page 50 Data Format Data Format T ools Code Programming ON Code Programming OFF Code ID Pre fi x Besides AIM pre fi x, Code ID pre fi x can be used to denote barcode format and can be customized. The Code ID pre fi x MUST be one (1) or two(2) visible English letters, capital or small, only . No Code ID Pre fi x 【 Pro CMD ： 99904 ...

  • Newland EM1300 - page 60

    nlscan.com Page 51 Data Format Data Format T ools Code Programming ON Code Programming OFF Program “ AGE ” as user suf fi x (The hex of “ AGE ” are0x41/0x47/0x45): 1. Read “ Code Programming ON ” 2. Read “ Program User Suf fi x ” 3. Read “ 4,1,4,7,4,5 ” in order 4. Read “ Save Programming ” 5. Read “ Code Programming OFF ...

  • Newland EM1300 - page 61

    nlscan.com Page 52 Data Format Data Format T ools Code Programming ON Code Programming OFF T erminal Program a W indows OS general line feed and carrage returen as terminal 1. Read “ Code Programming ON ” 2. Read “ Program T erminal ” 3. Read “ Set T erminal as 0x0D,0x0A and Enable Sending ” 4. Read “ Save ” 5. Read “ Code Program ...

  • Newland EM1300 - page 62

    nlscan.com Page 53 Introduction Each type of barcode has its unique attribute. W ith the programming code, the engine will adjust to the changes of these attributes. Disabling reading of the symbols which do not apply will improve reading performance. Symbols ...

  • Newland EM1300 - page 63

    nlscan.com Page 54 Symbols T ools Code Programming ON Code Programming OFF Code 128 Lo a d Fa c to ry De fa u lt Load Code 128 Factory Default 【 Pro CMD ： 99910000 】 Enable/Disable Code 128 Enable Code 128 【 Pro CMD ： 99910002 】 Disable Code 128 【 Pro CMD ： 99910001 】 When the engine can not read Code 128, please read “ Enable C ...

  • Newland EM1300 - page 64

    nlscan.com Page 55 Symbols T ools Code Programming ON Code Programming OFF Code 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths. If Max Message Length is equal to Min Message Length, the engine will only sup- port bar ...

  • Newland EM1300 - page 65

    nlscan.com Page 56 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 Lo a d Fa c to ry De fa u lt Load UCC/EAN-128 Factory Default 【 P r o CM D ： 99910100 】 Enable/Disable UCC/EAN-128 When the engine can not read UCC/EAN-128, please read “ Enable UCC/EAN-128 ” and try again. Enable UCC/EAN-128 【 Pro CMD ： 99910102 ? ...

  • Newland EM1300 - page 66

    nlscan.com Page 57 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths. If Max Message Length is equal to Min Message Length, the engine will only sup- port ...

  • Newland EM1300 - page 67

    nlscan.com Page 58 Symbols T ools Code Programming ON Code Programming OFF AIM 128 Load Factory Default Load AIM 128 Factory Default 【 P r o CM D ： 99910200 】 Enable/Disable AIM 128 When the engine can not read AIM 128, please read “ Enable AIM 128 ” and try again. Enable AIM 128 【 Pro CMD ： 99910202 】 Disable AIM 128 【 Pro CMD ? ...

  • Newland EM1300 - page 68

    nlscan.com Page 59 Symbols T ools Code Programming ON Code Programming OFF AIM 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths. If Max Message Length is equal to Min Message Length, the engine will only sup- port barc ...

  • Newland EM1300 - page 69

    nlscan.com Page 60 Symbols T ools Code Programming ON Code Programming OFF EAN-8 Load Factory Default Load EAN-8 Factory Default 【 Pro CMD ： 99910400 】 Enable/Disable EAN-8 Enable EAN-8 【 P r o CM D ： 9991402 】 Disable EAN-8 【 P r o CM D ： 99910401 】 EAN-8 Code ID Code ID Setting 【 Pro CMD ： 99910416 】 Example of setting EAN ...

  • Newland EM1300 - page 70

    nlscan.com Page 61 Symbols T ools Code Programming ON Code Programming OFF EAN-8 2 D ig it s A dd en d a Co d e 2 D ig it s A dd en d a Co d e is the one to the right of an ordinary code. Disable 2 Digits Addenda Code 【 Pro CMD ： 99910405 】 Enable 2 Digits Addenda Code 【 P r o CM D ： 99910406 】 Only Read W ith 2 digits Addenda Code 【 ...

  • Newland EM1300 - page 71

    nlscan.com Page 62 Symbols T ools Code Programming ON Code Programming OFF EAN-8 EA N -8 e x pa nd to E A N- 13 “ Do Not Expand to EAN-13 “ — keep original type and digits, do not expand. “ Expand to EAN-13 by Adding Leading 0s “ — expand to EAN-13 but keep code type. “ Expand Message and Convert to EAN-13 “ — expand code digits a ...

  • Newland EM1300 - page 72

    nlscan.com Page 63 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Lo a d Fa c to ry De fa u lt Load EAN-13 Factory Default 【 Pro CMD ： 99910500 】 Di s ab le / En ab l e EA N -1 3 Enable EAN-13 【 Pro CMD ： 99910502 】 Disable EAN-13 【 P ro CM D ： 99910501 】 When the engine can not read EAN-13, please read “ Enable ...

  • Newland EM1300 - page 73

    nlscan.com Page 64 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Ch e ck D i gi t T ransmit Check 【 Pro CMD ： 99910504 】 Do Not T ransmit Check 【 Pro CMD ： 99910503 】 EA N -1 3 is fi xed 13 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the ...

  • Newland EM1300 - page 74

    nlscan.com Page 65 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code. 2 Digits Addenda Code is the one to the right of an ordinary code. Disable 5 Digits Addenda Code 【 P r o CM D ： 99910510 】 Enable 5 Digits Addenda Code 【 P ...

  • Newland EM1300 - page 75

    nlscan.com Page 66 Symbols T ools Code Programming ON Code Programming OFF ISSN Load Factory Default Load ISSN Factory Default 【 Pro CMD ： 99910600 】 Enable/Disable ISSN Enable ISSN 【 P r o CM D ： 99910602 】 Disable ISSN 【 P r o CM D ： 99910601 】 ISSN Code ID Code ID Setting 【 Pro CMD ： 99910603 】 Example of setting ISSN Cod ...

  • Newland EM1300 - page 76

    nlscan.com Page 67 Symbols T ools Code Programming ON Code Programming OFF ISBN Load Factory Default Load ISBN Factory Default 【 Pro CMD ： 99910700 】 Enable/Disable ISBN Enable ISBN 【 P r o CM D ： 99910702 】 Disable ISBN 【 P r o CM D ： 99910701 】 When the engine can not read ISBN, please read “ Enable ISBN ” and try again. ...

  • Newland EM1300 - page 77

    nlscan.com Page 68 Symbols T ools Code Programming ON Code Programming OFF ISBN ISBN Code ID Code ID Setting 【 Pro CMD ： 99910705 】 Example of setting ISBN Code ID to “ p ” (0x70) 1. Read Enable Code Programming barcode. 2. Read ISSN Code ID Setting barcode. 3. Read Following Barcodes: “ 7 ” , and “ 0 ” 4. Read Save barcode 5. Rea ...

  • Newland EM1300 - page 78

    nlscan.com Page 69 Symbols T ools Code Programming ON Code Programming OFF UPC-E Lo a d Fa c to ry De fa u lt Load UPC-E Factory Default 【 P r o CM D ： 99911000 】 Di s ab le / En ab l e UP C -E Enable UPC-E 【 P r o CM D ： 99911002 】 Disable UPC-E 【 P r o CM D ： 99911001 】 When the engine can not read UPC-E, please read “ Enable ...

  • Newland EM1300 - page 79

    nlscan.com Page 70 Symbols T ools Code Programming ON Code Programming OFF UPC-E Check Digit UP C -E is fi xed 8 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 8 digits are right. T ransmit Check 【 Pro CMD ： 9991 1004 】 Do Not T ransmit Check 【 Pro CMD ...

  • Newland EM1300 - page 80

    nlscan.com Page 71 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD ： 9991 1010 】 Enable 5 Digits Addenda Code 【 Pro CMD ： 9991 1011 】 Only Read W ith 5 digits Addenda Code 【 Pro CMD ： 9991 1012 】 5 Digits Addenda Code is the one to the righ ...

  • Newland EM1300 - page 81

    nlscan.com Page 72 Symbols T ools Code Programming ON Code Programming OFF UPC-E Tra ns m it D e fa ul t “ 0 ” The fi rst byte of UPC-E is default to “ 0 ” . UP C -E E x pa nd to U P C- A Do Not Expand 【 Pro CMD ： 9991 1015 】 Expand to UPC-A 【 Pro CMD ： 9991 1016 】 Expand Message and Convert to UPC-A 【 Pro CMD ： 9991 1017 ? ...

  • Newland EM1300 - page 82

    nlscan.com Page 73 Symbols T ools Code Programming ON Code Programming OFF UPC-A Load Factory Default Load UPC-A Factory Default 【 P r o CM D ： 99911 100 】 Disable/Enable UPC-A When the engine can not read UPC-A, please read “ Enable UPC-A ” and try again. Enable UPC-A 【 Pro CMD ： 9991 1102 】 Disable UPC-A 【 Pro CMD ： 9991 1101 ...

  • Newland EM1300 - page 83

    nlscan.com Page 74 Symbols T ools Code Programming ON Code Programming OFF UPC-A Check Digit UPC-A is fi xed 13 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 13 digits are right. T ransmit Check 【 Pro CMD ： 9991 1104 】 Do Not T ransmit Check 【 Pro CMD ...

  • Newland EM1300 - page 84

    nlscan.com Page 75 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD ： 9991 11 10 】 Enable 5 Digits Addenda Code 【 Pro CMD ： 9991 11 1 1 】 Only Read W ith 5 digits Addenda Code 【 Pro CMD ： 9991 11 12 】 5 Digits Addenda Code is the one to the ...

  • Newland EM1300 - page 85

    nlscan.com Page 76 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Load Factory Default Load Interleaved 2 of 5 Factory Default 【 Pro CMD ： 9991 1200 】 Disable/Enable Interleaved 2 of 5 When the engine can not read Interleaved 2 of 5, please read “ Enable Interleaved 2 of 5 ” and try again Enable Interleaved 2 o ...

  • Newland EM1300 - page 86

    nlscan.com Page 77 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Check Digit Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages. If included, it could be the last digit. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and transmit » ...

  • Newland EM1300 - page 87

    nlscan.com Page 78 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Interleaved 2 of 5. The engine will send an error beep, if the decoded data length does not match the valid length. Interleaved 2 of 5 Message Length is de fi ned by “ Min. Message Length ” and “ ...

  • Newland EM1300 - page 88

    nlscan.com Page 79 Symbols T ools Code Programming ON Code Programming OFF ITF-6 ITF-6 is a fi xed length 6 bytes Interleaved 2 of 5 barcode with check digit. Wh e n e na b le d , I T F- 6 p r ec e de s 6 - by t e I nt e rl e av e d 2 o f 5 b ar c od e . Load ITF-6 Factory Default 【 Pro CMD ： 9991 1300 】 Disable ITF-6 User Selection 【 P r ...

  • Newland EM1300 - page 89

    nlscan.com Page 80 Symbols T ools Code Programming ON Code Programming OFF ITF-14 ITF-14 is a fi xed length of 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. Wh e n e na b le d , I T F- 1 4 p re c ed e s 1 4- b yt e I n te r le a ve d 2 o f 5 b a rc o de . Load ITF-14 Factory Default 【 Pro CMD ： 9991 ...

  • Newland EM1300 - page 90

    nlscan.com Page 81 Symbols T ools Code Programming ON Code Programming OFF Deutshe14 Load Factory Default Load Deutshe14 Factory Default Deutshe14 Factory Default Factory Default 【 Pro CMD ： 9991 1500 】 Disable/Enable Deutshe14 When the engine can not read Deutshe14, please read “ Enable Deutshe14 ” and try again If Deutsche 14 and ITF-14 ...

  • Newland EM1300 - page 91

    nlscan.com Page 82 Symbols T ools Code Programming ON Code Programming OFF Deutshe12 Load Factory Default Load Deutshe12 Factory Default Deutshe12 Factory Default Factory Default 【 Pro CMD ： 9991 1600 】 Disable/Enable Deutshe12 When the engine can not read Deutshe12, please read “ Enable Deutshe12 ” and try again. If Deutsche 12 and ITF-1 ...

  • Newland EM1300 - page 92

    nlscan.com Page 83 Symbols T ools Code Programming ON Code Programming OFF COOP25 （ Japanese Matrix 25 ） Load Factory Default Load COOP25 Factory Default 【 P r o CM D ： 99911700 】 Enable/ Disable COOP25 When the engine can not read COOP25, please read “ Enable COOP25 ” and try again. Enable COOP25 【 Pro CMD ： 9991 1702 】 Disable ...

  • Newland EM1300 - page 93

    nlscan.com Page 84 Symbols T ools Code Programming ON Code Programming OFF COOP25 （ Japanese Matrix 25 ） Check Digit COOP25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and transmit ? ...

  • Newland EM1300 - page 94

    nlscan.com Page 85 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of COOP25. The engine will send an error beep, if the decoded data length does not match the valid length. COOP25 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length ” ...

  • Newland EM1300 - page 95

    nlscan.com Page 86 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Lo a d Fa c to ry De fa u lt Load Matrix 25 Factory Default 【 P r o C MD ： 99912000 】 Enable/ Disable Matrix 25 When the engine can not read Matrix 25, please read “ Enable Matrix 25 ” and try again. Enable Matrix 25 【 Pro CMD ： 9 ...

  • Newland EM1300 - page 96

    nlscan.com Page 87 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Check Digit Matrix 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and trans- » ...

  • Newland EM1300 - page 97

    nlscan.com Page 88 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Matrix 25. The engine will send an error beep, if the decoded data length does not match the valid length. Matrix 25 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Lengt ...

  • Newland EM1300 - page 98

    nlscan.com Page 89 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Load Factory Default Load Industrial 25 Factory Default 【 P r o CM D ： 99912100 】 Enable/ Disable Industrial 25 When the engine can not read Industrial 25, please read “ Enable Industrial 25 ” and try again. Enable Industrial 25 【 Pro CMD ： 999121 ...

  • Newland EM1300 - page 99

    nlscan.com Page 90 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Check Digit Industrial 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and trans- » mit all bytes ...

  • Newland EM1300 - page 100

    nlscan.com Page 91 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Industrial 25. The engine will send an error beep, if the decoded data length does not match the valid length. Industrial 25 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Messa ...

  • Newland EM1300 - page 101

    nlscan.com Page 92 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Load Factory Default Load Standard 25 Factory Default 【 P r o CM D ： 99912200 】 Enable/ Disable Standard 25 When the engine can not read Standard 25, please read “ Enable Standard 25 ” and try again. Enable Standard 25 【 Pro CMD ： 99912202 】 Disab ...

  • Newland EM1300 - page 102

    nlscan.com Page 93 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Check Digit Standard 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and trans- » mit all bytes inc ...

  • Newland EM1300 - page 103

    nlscan.com Page 94 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Standard 25. The engine will send an error beep, if the decoded data length does not match the valid length. Standard 25 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message L ...

  • Newland EM1300 - page 104

    nlscan.com Page 95 Symbols T ools Code Programming ON Code Programming OFF Code 39 Load Factory Default Load Code 39 Factory Default 【 P r o CM D ： 99912400 】 Enable/Disable Code 39 When the engine can not read Code 39, please read “ Enable Code 39 ” and try again Enable Code 39 【 Pro CMD ： 99912402 】 Disable Code 39 【 Pro CMD ： ...

  • Newland EM1300 - page 105

    nlscan.com Page 96 Symbols T ools Code Programming ON Code Programming OFF Code 39 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep. E.g. ： Reading a 4-byte (include check byte) Code 39 with the Min Message Length being 4 bytes and “ Chec ...

  • Newland EM1300 - page 106

    nlscan.com Page 97 Symbols T ools Code Programming ON Code Programming OFF Code 39 T ransmit Start & Stop Character Code 39 has one "*" before and another after digits as Start & Stop Character . T ransmission of “ * ” can be selected. T ransmit Both “ * ” 【 Pro CMD ： 99912407 】 T ransmit Neither “ * ” 【 Pro CM ...

  • Newland EM1300 - page 107

    nlscan.com Page 98 Symbols T ools Code Programming ON Code Programming OFF Code 39 Select Message Length Code 39 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Code 39. The engine will send an error beep, if the decoded data length does not match the val ...

  • Newland EM1300 - page 108

    nlscan.com Page 99 Symbols T ools Code Programming ON Code Programming OFF Codabar Load Factory Default Load Codabar Factory Default 【 Pro CMD ： 99912500 】 Enable/Disable Codabar When the engine can not read Codabar , please read “ Enable Codabar ” and try again. Enable Codabar 【 Pro CMD ： 99912502 】 Disable Codabar 【 Pro CMD ： ...

  • Newland EM1300 - page 109

    nlscan.com Page 100 Symbols T ools Code Programming ON Code Programming OFF Codabar When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep. E.g. ： Reading a 4-byte (include check byte) Codabar with the Min Message Length being 4 bytes and “ Che ...

  • Newland EM1300 - page 110

    nlscan.com Page 101 Symbols T ools Code Programming ON Code Programming OFF Codabar T ransmit Start & Stop Character Do Not T ransmit Both Start & Stop Character 【 Pro CMD ： 99912506 】 Use ABCD/ABCD As Start & Stop Character 【 Pro CMD ： 99912510 】 Use abcd/abcd As Start & Stop Character 【 Pro CMD ： 99912512 】 T ran ...

  • Newland EM1300 - page 111

    nlscan.com Page 102 Symbols T ools Code Programming ON Code Programming OFF Codabar Select Message Length Codabar Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Codabar . The engine will send an error beep, if the decoded data length does not match the v ...

  • Newland EM1300 - page 112

    nlscan.com Page 103 Symbols T ools Code Programming ON Code Programming OFF Code 93 Load Factory Default Load Code 93 Factory Default 【 P r o CM D ： 99912600 】 Enable /Disable Code 93 When the engine can not read Code 93, please read “ Enable Code 93 ” and try again. Enable Code 93 【 Pro CMD ： 99912602 】 Disable Code 93 【 Pro CMD ...

  • Newland EM1300 - page 113

    nlscan.com Page 104 Symbols T ools Code Programming ON Code Programming OFF Code 93 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep. E.g. ： Reading a 4-byte (include check byte) Code 93 with the Min Message Length being 4 bytes and “ Che ...

  • Newland EM1300 - page 114

    nlscan.com Page 105 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 93. The engine will send an error beep, if the decoded data length does not match the valid length. Code 93 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length . ...

  • Newland EM1300 - page 115

    nlscan.com Page 106 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Load Factory Default Load Code 1 1 Factory Default 【 P r o CM D ： 99912700 】 Enable/ Disable Code 1 1 When the engine can not read Code 1 1, please read “ Enable Code 1 1 ” and try again. Enable Code 1 1 【 Pro CMD ： 99912702 】 Disable Code 1 1 【 P ...

  • Newland EM1300 - page 116

    nlscan.com Page 107 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Check Digit Code 1 1 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and trans- » mit all by ...

  • Newland EM1300 - page 117

    nlscan.com Page 108 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 1 1. The engine will send an error beep, if the decoded data length does not match the valid length. Code 1 1 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length ...

  • Newland EM1300 - page 118

    nlscan.com Page 109 Symbols T ools Code Programming ON Code Programming OFF Plessey Load Factory Default Load Plessey Factory Default 【 P r o CM D ： 99913000 】 Enable/ Disable Plessey When the engine can not read Plessey , please read “ Enable Plessey ” and try again. Enable Plessey 【 Pro CMD ： 99913002 】 Disable Plessey 【 Pro CMD ...

  • Newland EM1300 - page 119

    nlscan.com Page 1 10 Symbols T ools Code Programming ON Code Programming OFF Plessey Check Digit Plessey may include Check Digits (not compulsory) following its barcode messages. If included, they are the last two digit. They veri fi e the barcode message. “ NO Check, T ransmit All ” means to read without check and transmit » all bytes includ ...

  • Newland EM1300 - page 120

    nlscan.com Page 1 11 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Plessey . The engine will send an error beep, if the decoded data length does not match the valid length. Plessey Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length ...

  • Newland EM1300 - page 121

    nlscan.com Page 1 12 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Load Factory Default Load MSI-Plessey Factory Default 【 P r o CM D ： 99913100 】 Enable/ Disable MSI-Plessey When the engine can not read MSI-Plessey , please read “ Enable MSI-Plessey ” and try again. Enable MSI-Plessey 【 Pro CMD ： 99913102 】 Di ...

  • Newland EM1300 - page 122

    nlscan.com Page 1 13 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Check Digit MSI-Plessey may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It veri fi es the barcode message. “ NO Check, T ransmit All ” means to read without check and trans- » mit ...

  • Newland EM1300 - page 123

    nlscan.com Page 1 14 Symbols T ools Code Programming ON Code Programming OFF Select Message Length MSI-Plessey Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length ” .It is used to program the valid reading length of MSI-Plessey . The engine will send an error beep, if the decoded data length does not match the ...

  • Newland EM1300 - page 124

    nlscan.com Page 1 15 Symbols T ools Code Programming ON Code Programming OFF GS1 Databar Load Factory Default Load GS1 Databar Factory Default 【 P r o CM D ： 99913200 】 Enable/ Disable GS1 Databar When the engine can not read GS1 Databar , please read “ Enable GS1 Databar ” and try again. Enable GS1 Databar 【 Pro CMD ： 99913202 】 Di ...

  • Newland EM1300 - page 125

    nlscan.com Page 1 16 Appendix Factory Default List Parameters Factory Default Remark General Programming Code Programming On Send Pro Code V alue Off W orking Mode Hand-held Mode Reading a Barcode T ime Length 3s Range ： 0-15s ， 0 is in fi nite time. Interval Length 1s Range ： 0-7.5s Sensitivity High Sensitivity En a bl ed in S e ns or Mo de ...

  • Newland EM1300 - page 126

    nlscan.com Page 1 17 Appendix Factory Default List Parameters Factory Default Remark Symbol Code 128 Enable On Max Message Length 255 Min Message Length 1 UCC/EAN-128 Enable On Max Message Length 255 Min Message Length 1 AIM 128 Enable Off Min Message Length 1 EAN-8 Enable On Send Check Digit On Enable 2 Digits Addenda Code Off Enable 5 Digits Adde ...

  • Newland EM1300 - page 127

    nlscan.com Page 1 18 Appendix Factory Default List ISSN Enable Off ISBN Enable Off Use 10 Digits Off UPC-E Enable On Send Check Digit On Enable 2 Digits Addenda Code Off Enable 5 Digits Addenda Code Off Only Read W ith 2 digits Addenda Code Off Only Read W ith 5 digits Addenda Code Off Expand to UPC-A Off Expand and Change T ype to UPC-A Off Send D ...

  • Newland EM1300 - page 128

    nlscan.com Page 1 19 Appendix Factory Default List Deutsche 14 Enable Off Send Check Digit On Deutsche 12 Enable Off Send Check Digit On COOP 25(Japanese Matrix 25) Enable Off Check Off Send Check Digit Off Max Message Length 255 Min Message Length 6 No less than 4 Matrix 25(European Matrix 25) Enable On Check Off Send Check Digit Off Max Message L ...

  • Newland EM1300 - page 129

    nlscan.com Page 120 Appendix Factory Default List Support Full ASCII On Max Message Length 255 Min Message Length 4 No less than 4 (including St a rt & St o p Ch a ra ct e r) Codabar Enable On Check Off Se n d Ch e ck D i gi t Of f Se n d St a rt & St op Ch ar a ct er On AB C D/ AB C D as St ar t & S t op C h ar ac t er On Ch o os e 1 I ...

  • Newland EM1300 - page 130

    nlscan.com Page 121 Appendix Factory Default List Max Message Length 255 Min Message Length 4 No less than 1 MSI-Plessey Enable Off Send Check Digit Off No Check On 1 D ig it , MOD10 Check Off 2 D ig it s , MOD10/MOD10 Check Off 2 D ig it s , MOD10/MOD1 1 Check Off Max Message Length 255 Min Message Length 4 No less than 1 GS1 Databar Enable On Max ...

  • Newland EM1300 - page 131

    nlscan.com Page 122 Appendix AIM ID List Symbol AIM ID Possible AIM ID Modi fi ers(m) Code 128 ]C 0 UCC/EAN-128 ]C 1 AIM 128 ]C 2 IS B T 1 2 8 ]C 4 EAN-8 ]E 4 EAN-13 ]E 0 EAN-13 with Addon ]E 3 ISSN ]X 0 ISBN ]X 0 UPC-E ]E 0 UPC-E with Addon ]E 3 UPC-A ]E 0 UPC-A with Addon ]E 3 Interleaved 2 of 5 ]I m 0, 1 ,3 ITF-6 ]I m 1, 3 ITF-14 ]I m 1, 3 Deut ...

  • Newland EM1300 - page 132

    nlscan.com Page 123 Appendix Code ID List Symbol Code ID Code 128 j UCC/EAN-128 u AIM 128 f IS B T 1 2 8 t EAN-8 g EAN-13 d ISSN n ISBN B UPC-E h UPC-A c Interleaved 2 of 5 e ITF-6 r ITF-14 q Deutsche 14 w Deutsche 12 l COOP 25 （ Japanese Matrix 25 ） o Matrix 25(European Matrix 25) v Industrial 25 i Standard 25 s Code 39 b Codabar a Code 93 y C ...

  • Newland EM1300 - page 133

    nlscan.com Page 124 Appendix Appendix T ools Code Programming ON Code Programming OFF Digit Code It is must to read save after reading digit code. 0 【 Pro CMD ：99900000】 1 【 Pro CMD ：99900001】 2 【 Pro CMD ：99900002】 3 【 Pro CMD ：99900003】 4 【 Pro CMD ：99900004】 5 【 Pro CMD ：99900005】 6 【 Pro CMD ：99900006】 ...

  • Newland EM1300 - page 134

    nlscan.com Page 125 Appendix Digit Code 8 【 Pro CMD ：99900010】 9 【 Pro CMD ：99900011】 A 【 Pro CMD ：99900012】 B 【 Pro CMD ：99900013】 C 【 Pro CMD ：99900014】 D 【 Pro CMD ：99900015】 E 【 Pro CMD ：99900016】 F 【 Pro CMD ：99900017】 T ools Code Programming ON Code Programming OFF ...

  • Newland EM1300 - page 135

    nlscan.com Page 126 Appendix Appendix T ools Code Programming ON Code Programming OFF Save and Abort In order to save the received data “ Save ” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.. Eg, after a program code is received then ‘ 1 2 ...

  • Newland EM1300 - page 136

    nlscan.com Page 127 Revisions V ersion Data Source Description Date Approved Pre-release version 20090826 ...

Manufacturer Newland Category Barcode readers

Documents that we receive from a manufacturer of a Newland EM1300 can be divided into several groups. They are, among others:
- Newland technical drawings
- EM1300 manuals
- Newland product data sheets
- information booklets
- or energy labels Newland EM1300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Newland EM1300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Newland EM1300, service manual, brief instructions and user manuals Newland EM1300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Newland EM1300.

Similar manuals

A complete manual for the device Newland EM1300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Newland EM1300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Newland EM1300.

A complete Newland manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Newland EM1300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Newland EM1300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Newland EM1300, that we can find in the current document
3. Tips how to use the basic functions of the device Newland EM1300 - which should help us in our first steps of using Newland EM1300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Newland EM1300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Newland EM1300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Newland EM1300?

Use the form below

If you did not solve your problem by using a manual Newland EM1300, ask a question using the form below. If a user had a similar problem with Newland EM1300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)