English dropdown-ico

Manual Actron 9040

12 pages 0.64 mb
Download

Go to site of 12

Summary
  • Actron 9040 - page 1

    Retrieves Global (Generic) OBD II diagnostic codes and displays their definitions on Foreign and Domestic OBD II compliant vehicles 9040 Global OBD II Code Scanner ® Content s Safety Precautions ................................................................................... 2 About OBD II ....................................................... ...

  • Actron 9040 - page 2

    2 OBD II stands for On-Board Diagnostics version II. OBD II is a system that the Society of Automotive Engineers (SAE) developed to standardize automotive electronic diagnosis to minimize vehicle pollution and to allow you to use the same tool to test any make and model without special adapters. The SAE established guidelines that provide:  a un ...

  • Actron 9040 - page 3

    3 Diagnostic T r ouble Code(s) (DTC) Diagnostic Trouble Codes (DTCs) consist of a five-digit alphanumeric code in the for- mat shown below . When the On-Board Computer recognizes and identifies a problem in the computer-monitored systems, a DTC for that fault is stored in memory . These codes are intended to help you determine the root cause of a p ...

  • Actron 9040 - page 4

    4 Control and Indicators The scan tool is designed to be as intuitive as possible. All menu and lists operate the same way .  ENTER Key - selects displayed items and moves cursor in the Code Lookup function.  YES/UP Arrow Key - responds yes to prompts, scrolls up and changes numbers in Code Lookup.  NO/DOWN Arrow Key - responds no to promp ...

  • Actron 9040 - page 5

    5 Using the Code Scanner ® Turn the ignition key to the KOEO or KOER. Select Read Codes and press ENTER . If there are no codes stored in vehicle memory , a System Pass message displays. If codes have been stored in vehicle memory , then the num- ber of codes and type display (i.e. = 1 of 3 ; ). Press the DOWN arrow to view the codes. The de ...

  • Actron 9040 - page 6

    6 Using the Code Scanner ® Select I/M Monitors and press the ENTER key . Each I/M monitor and its status display per screen. Use the arrow keys to view them. When done, press the BACK key .  A status of Ready means that the required driving conditions for that monitor have been meet and it passed.  A status of Not Ready means tha ...

  • Actron 9040 - page 7

    7  Inspect all vacuum hoses for: * Correct routing. Refer to vehicle service manual, or V ehicle Emission Control Information (VECI) decal located in the engine compartment. * Pinches and kinks. * S plits, cut s or breaks  Inspect wiring for: * Contact with sharp edges (a common problem). * Contact with hot surfaces, such as exhaust  Inspe ...

  • Actron 9040 - page 8

    8 V ehicle Service Information V ehicle service manuals containing additional diagnostic information are available at most auto parts stores or the local library . If unable to locate them at those locations, write the below listed publishers for availability and pricing. Please be sure to specify the make, model and year of vehicle. Chilton Book C ...

  • Actron 9040 - page 9

    9 Gl obal P arameter li st All parameter identification data (PID) listed was verified on actual vehicles to guaran- tee accuracy . Definitions used to describe all PIDs were obtained from reliable sources and are accurate at time of printing. It is possible that some newer vehicles may contain data different from that listed in Appendix A. Always ...

  • Actron 9040 - page 10

    10 CALC LOAD (0 - 100%) Calulated LOAD Value indicates load on engine. C A T TEMPxy (-40°C - 6513.5°C) or (-40 - 9999.9F) Cataly st T emperature Bank shall display catalyst substrate temperature for bank catalyst, if used by control module strategy for on board diagnostics monitoring, bank, sensor catalyst or tempera- ture sensor. CLR DST (0km-65 ...

  • Actron 9040 - page 11

    11 4. OPEN2: The PCM is operating in Open Loop control strategy due to detected system fault. Certain actuator or sensor faults will cause module to use an open loop strategy . 5. CLSD1: Closed Loop control is current storage being used by module, but a fault with at least one O2 sensor has been detected. The control system may be using single O2 f ...

  • Actron 9040 - page 12

    ©2004 SPX Actron. All Rights Reserved. Printed in USA 0002-002-2356 REL TPS (0 - 100%) Relative Throttle Position is relative throttle position at normal position. SECOND AI R (AI R_ST AT : UPS, DNS or OFF) Commanded Secondary Air St atus is on newer vehicles and actuators to control pollution control. UPS - UP STREAM module is demanding that seco ...

Manufacturer Actron Category Scanner

Documents that we receive from a manufacturer of a Actron 9040 can be divided into several groups. They are, among others:
- Actron technical drawings
- 9040 manuals
- Actron product data sheets
- information booklets
- or energy labels Actron 9040
All of them are important, but the most important information from the point of view of use of the device are in the user manual Actron 9040.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Actron 9040, service manual, brief instructions and user manuals Actron 9040. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Actron 9040.

Similar manuals

A complete manual for the device Actron 9040, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Actron 9040 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Actron 9040.

A complete Actron manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Actron 9040 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Actron 9040, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Actron 9040, that we can find in the current document
3. Tips how to use the basic functions of the device Actron 9040 - which should help us in our first steps of using Actron 9040
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Actron 9040
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Actron 9040 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Actron 9040?

Use the form below

If you did not solve your problem by using a manual Actron 9040, ask a question using the form below. If a user had a similar problem with Actron 9040 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)