English dropdown-ico

Manual Graco Inc. 309273

16 pages 0.68 mb
Download

Go to site of 16

Summary
  • Graco Inc. 309273 - page 1

    Ultra Max t Electric Airless Sprayers Operating Instructions The intent of these instructions is to provide the new painter with a quick and easy reference to become familiar with airless sprayers. This does not replace the Instruction Manual supplied with this sprayer . Read and understand the instructions and warnings in that manual. Important No ...

  • Graco Inc. 309273 - page 2

    2 309273 PRESSURE RELIEF – Do this when cleaning, repairing or shuting down sprayer WASTE RESÍDUOS À JETER DESECHO 1. T urn pressure to lowest setting. T urn power OFF . Unplug sprayer . 2. T rigger gun to relieve pressure. 3. Put drain tube in pail . T urn prime valve down. W ARNING Fire and explosion hazard: Solv ent and pa i nt f um es c an ...

  • Graco Inc. 309273 - page 3

    3 309273 Power Switch Pressure Control Component Identification Suction T ube Filter Prime V alve Prime/drain position Paint position Spray Gun T rigger Safety Put trigger safety ON when not spraying. T ake trigger safety OFF before triggering gun. Digital Display (Not available on all models) 15/20A Switch AutoClean V alve (Not available on all mo ...

  • Graco Inc. 309273 - page 4

    4 309273 1. Connect Graco airless hose to sprayer . T ighten securely . 2. Connect other end of hose to gun. Setup 3. T ighten securely . 4. Remove tip guard. ...

  • Graco Inc. 309273 - page 5

    5 309273 5. Check inlet strainer for clogs and debris. 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray . Approximate Fill Level ...

  • Graco Inc. 309273 - page 6

    6 309273 P AINT FLUSH 7. T urn power OFF . 8. Plug power supply cord into a properly grounded electrical outlet. 9. T urn prime valve down. 10. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. Do 1 . – 5 . of Startup to flush out storage oil shipped ...

  • Graco Inc. 309273 - page 7

    7 309273 FLUSH Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , do Pressure Relief . T ighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. Startup 15 SEC 1. T urn prime valve down. T urn pressure control to lowest pressu ...

  • Graco Inc. 309273 - page 8

    8 309273 FLUSH P AINT General Surfaces T ip Recommendations Chart Wood Interi or C ab- inets , Paneling Interior Walls or Ceilings Dry wall, Plaster Ov er Hang Su rfaces Materi als Filter Mesh 6–8 8–10 10–12 12–14 Orific e Size (in. ) Fan Widt h ( in.) at 12 in . Masonr y Bl ock, Stu cco, Co ncre te Wood Ex terior Shingle, Siding, Shiplap O ...

  • Graco Inc. 309273 - page 9

    9 309273 SwitchTip and Guard Assembly 1. Insert SwitchT ip. Insert seat and OneSeal. 2. Screw assembly onto gun. Hand tighten. SwitchT ip OneSeal seat Press SMARTCONTROL button to cycle through PRESSURE – GAL/L TR – TIMER displays D PRESSURE : Fluid pressure at the sprayer D GAL/L TR : Accumulated total of gallons/liters sprayed D TIMER : Durat ...

  • Graco Inc. 309273 - page 10

    10 309273 Spray T est Pattern heavy edges Clearing Tip Clogs 1. T rigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular , 10–12 in. (25–30 cm) from surface. Spray back and forth. Use strokes overlapped by 50%. Start ...

  • Graco Inc. 309273 - page 11

    11 309273 Cleanup P AINT 1. T urn power OFF . 2. T urn pressure to lowest setting. T rigger gun to relieve pressure. 3. T urn prime valve down. 4. Remove filter assembly and assemble gun without filter . Perform AutoClean procedure (Manual 309278) or follow conventional flushing/cleaning procedure that follows: ti2874a Contractor Contractor II ...

  • Graco Inc. 309273 - page 12

    12 309273 5. Remove guard and SwitchT ip. 6. Clean filter , guard and SwitchT ip in flushing fluid. P AINT FLUSH 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint. 8. If sprayer has a filter , unscrew bowl, remove filter . Assemble without filter . Clean filter . ...

  • Graco Inc. 309273 - page 13

    13 309273 P AINT FLUSH 9. T urn power ON. 10. T urn prime valve hori- zontal. 1 1. Hold gun against paint pail. T ake trigger safety OFF . T rigger gun until flushing fluid appears. 12. Move gun to flushing pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and put trigger safety ON. 13. T urn prime valve down and ...

  • Graco Inc. 309273 - page 14

    14 309273 P AINT FLUSH FLUSH 14. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. T urn power OFF . 15. Make sure plastic center tube is tightened securely . Install filter bowl and filter . Hand tighten filter bowl. Install filter assembly into gun. Hand tighten gun handle. 16. Wipe sprayer , hose and gun ...

  • Graco Inc. 309273 - page 15

    15 309273 T rouble Shooting TYPE OF PROBLEM WHA T TO CHECK If check is OK, go to next check WHA T TO D O When check is not OK refer to this column D Sprayer does not respond 1. Check if error code is displayed, page 9. 1. Refer to your repair manual. D Sprayer will not prime or takes too long to prime 1 . Air in paint pump 1. Open prime valve to pu ...

  • Graco Inc. 309273 - page 16

    16 309273 Daily: Inspect, clean and replace as needed D Manifold filter , gun filter and inlet stainer D W et cup for leakage, tighten if needed D TSL level D Gun trigger safety D T ip wear , replace if necessary D Electric cord and plug W eekly: D Check tightness of wet cup. D Inspect all high pressure paint hoses. Annually: D Schedule maintenance ...

Manufacturer Graco Inc. Category Paint Sprayer

Documents that we receive from a manufacturer of a Graco Inc. 309273 can be divided into several groups. They are, among others:
- Graco Inc. technical drawings
- 309273 manuals
- Graco Inc. product data sheets
- information booklets
- or energy labels Graco Inc. 309273
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco Inc. 309273.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco Inc. 309273, service manual, brief instructions and user manuals Graco Inc. 309273. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco Inc. 309273.

Similar manuals

A complete manual for the device Graco Inc. 309273, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco Inc. 309273 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco Inc. 309273.

A complete Graco Inc. manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco Inc. 309273 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco Inc. 309273, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco Inc. 309273, that we can find in the current document
3. Tips how to use the basic functions of the device Graco Inc. 309273 - which should help us in our first steps of using Graco Inc. 309273
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco Inc. 309273
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco Inc. 309273 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco Inc. 309273?

Use the form below

If you did not solve your problem by using a manual Graco Inc. 309273, ask a question using the form below. If a user had a similar problem with Graco Inc. 309273 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)