English dropdown-ico

Manual Vermont Casting 7PDVS

24 pages 3.31 mb
Download

Go to site of 24

Summary
  • Vermont Casting 7PDVS - page 1

    DV Power V ent System Model 7PDVS DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE V APOURS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. FOR YOUR SAFETY WHA T T O DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Extinguish all flames. • Imme ...

  • Vermont Casting 7PDVS - page 2

    D V Pow er V e nt S ystem 2 10003262 General Information .................................................................................................... 3 Power System Parts and Description ......................................................................... 4 Clearance to Combustibles ..................................................... ...

  • Vermont Casting 7PDVS - page 3

    3 D V Pow er V e nt S ystem 10003262 • This DV Power V ent System was designed to be used only on units with electronic ignition (EN or EP). • This DV Power V ent System was certified by CSA to be used only with CFM Corporation Direct V ent models, as listed in this manual. • This DV Power V ent System can be used with any CFM Corporation si ...

  • Vermont Casting 7PDVS - page 4

    D V Pow er V e nt S ystem 4 10003262 1. DV POWER VENT box assembled with a 6FT power cord. 2. T wo deflectors to be added to the side wall vent termination. 3. Assorted restrictor orifice plates to be used according to the instructions for specific models. 4. Installation and Operating Instruction Manual. DV Power V ent System Parts and Descript ...

  • Vermont Casting 7PDVS - page 5

    5 D V Pow er V e nt S ystem 10003262 • The DV Power V ent System box needs a minimum 1” clearance all around the box. The DV Power V ent System box already has a 1” stand-off on all sides. • Pipes from the fireplace to the DV Power V ent System box and from the box to the vent termination need: • Clearance to combustible materials of 1? ...

  • Vermont Casting 7PDVS - page 6

    D V Pow er V e nt S ystem 6 10003262 Models Input (BTU/h) Restrictor Orifice Size 33BDVT or 33BDVR 15,000 23/32” 36BDVT or 36BDVR 18,000 29/32” DVR33 20,000 31/32” 39BDVT or 39BDVR 22,000 31/32” 43BDVT or 43BDVR 25,000 1” DVRT36 25,000 1” DV360 30,000 1 ¹⁄₃₂ ” DVRT39 30,000 1 ¹⁄₃₂ ” DVRT43 33,000 1 ¹⁄₁₆ ” 360 ...

  • Vermont Casting 7PDVS - page 7

    7 D V Pow er V e nt S ystem 10003262 1-Changing the Restrictor Orifice Plate: Before installation of the power vent box (RECOMMENDED): A. From the inlet side, remove the two 3/8” nuts holding the orifice plate. B. Remove the orifice plate. C. Install the correct restrictor orifice plate according to the chart above. D. Place back the two nuts ...

  • Vermont Casting 7PDVS - page 8

    D V Pow er V e nt S ystem 8 10003262 Install pipes and elbows according to the lay-out from the unit to the Power V ent System Box and from it to the vent termination. Follow the vent installation accord- ing to the fireplace manual recommendations. 2-Install the V ent Pipes and the DV Power V ent System Box: Remember that the blower shaft MUST AL ...

  • Vermont Casting 7PDVS - page 9

    9 D V Pow er V e nt S ystem 10003262 L 6 L 7 L 5 L 2 L 4 L 3 L 1 In the above example there are: 4 times 90 degrees elbows = 360 degrees 2 times 45 degrees elbows = 90 degrees T otal elbow degrees = 450 degrees Installation is OK A - Maximum 40FT of straight pipe. B - Minimum 10FT of straight pipe for units up to 33,000BTU/h, Minimum 15FT of straig ...

  • Vermont Casting 7PDVS - page 10

    D V Pow er V e nt S ystem 10 10003262 V enting Down: A - Maximum 40 FT of straight pipe. B- Minimum 10FT of straight pipe for units up to 33,000BTU/h, Minimum 15 FT of straight pipe for units from 33,000BTU/h to 40,000BTU/h. C -Maximum 6 FT of straight pipe. D -Maximum 12 FT down. A = L 1 +L 2 +L 3 +L 4 +L 5 +L 6 B = L 1 +L 2 +L 3 +L 4 C = L 5 +L 6 ...

  • Vermont Casting 7PDVS - page 11

    1 1 D V Pow er V e nt S ystem 10003262 3- DV Power V ent System Setup: 3.1 - Checking the Pressure Switch Position: The pressure switch diaphragm must be in a vertical plane. The pressure switch hose connections should NEVER point up. The BEST position is pointing down, but can be pointed to the sides. Depending on the final location of the DV Pow ...

  • Vermont Casting 7PDVS - page 12

    D V Pow er V e nt S ystem 12 10003262 3.3 - Adding Deflectors to the Side W all V ent T ermination: 1. Open the plastic bag and check all components. (One T op Deflector , one Bottom Deflector , four self-tapping screws) 2. Install the bottom deflector using two screws provided with the kit. Refer to Figure A. 3. Open the top screen and install ...

  • Vermont Casting 7PDVS - page 13

    13 D V Pow er V e nt S ystem 10003262 COM NO NC BLUE YELLOW WHITE RTN HOT BLACK BLACK 90fl FEMALE 1/4" QC TERMINAL YELLOW BLACK 24 V AC RET WHITE GREEN BLACK BLACK 120 V AC HOT GREEN OR ON/OFF SWITCH TO WALL THERMOST A T BUSHING 40V A TRANSFORMER 90fl FEMALE BLUE 24 V AC HOT NOV A SIT 822 V AL VE LO HI BLACK 9 SP ARK 5 6 GREEN 4 2 3 ORANGE 2 ...

  • Vermont Casting 7PDVS - page 14

    D V Pow er V e nt S ystem 14 10003262 COM NO NC BLUE YELLOW WHITE RTN HOT BLACK WHITE GREEN OR ON/OFF SWITCH TO WALL THERMOST A T BUSHING WIRE SPEC.: FIELD SUPPLIED MINIMUM INSULA TION 2/64" 18 AWS SOLID, LOW VOL T AGE & INST ALLED WIRES Power V ent Kit LED J2 120V ac Hot 120V ac Rtn Fan Rtn Fan Hot Key Flame Sense Chasis / Burner Ground 1 ...

  • Vermont Casting 7PDVS - page 15

    15 D V Pow er V e nt S ystem 10003262 T urn the switch ON/OFF or the wall thermostat, to the ON position. Blower will start immediately and will purge the unit and the vent system for 45 seconds. At that point, the pilot will light and the main burner(s) will follow . When the switch ON/OFF or the wall thermostat, is turned to OFF , the main burner ...

  • Vermont Casting 7PDVS - page 16

    D V Pow er V e nt S ystem 16 10003262 If there is a need to change the restrictor plate orifice on the DV Power V ent System box, follow the steps below: A. T urn the power OFF to fireplace and power vent. B. Remove the blower ’s cover (two parts): • Remove the hose attached to the blower casing. • Remove two screws. Refer to Figure A. • ...

  • Vermont Casting 7PDVS - page 17

    17 D V Pow er V e nt S ystem 10003262 Screws Figure A Figure B Figure C Figure D Figure E Figure F ...

  • Vermont Casting 7PDVS - page 18

    D V Pow er V e nt S ystem 18 10003262 T roubleshooting the Power V ent System Power vent motor is working? Does the Pilot Spark? Pilot Burner Lights? ON/OFF switch or wall thermostat “ON”? Is there 120V power to the fireplace and power vent? Are all wiring connections tight? (T urn off Power before checking) Is there 24V at the power vent circ ...

  • Vermont Casting 7PDVS - page 19

    19 D V Pow er V e nt S ystem 10003262 T roubleshooting the Power V ent System Power vent motor is working? Does the Pilot Spark? Pilot Burner Lights? ON/OFF switch or wall thermostat “ON”? Is there 120V power to the fireplace and power vent? Are all wiring connections tight? (T urn off Power before checking) Is the LED light on the ignition co ...

  • Vermont Casting 7PDVS - page 20

    D V Pow er V e nt S ystem 20 10003262 1 2 3 5 4 6 7 14 1 1 15 16 9 10 8 Ref. Description 7PDVS 1. Hose High T emperature 10003405 2. Shield Heat Blower Right Assy 10003673 3. Shield Heat Blower Left Assy 10003672 4. Blower 10003214 5. Gasket Blower 10003066 6. Gasket Blower Plate 10002280 7. Pressure Switch 10003213 8. Circuit Board 10003230 9. Cov ...

  • Vermont Casting 7PDVS - page 21

    21 D V Pow er V e nt S ystem 10003262 7PDVS DV Power V ent System (continued) Ref. Description 7PDVS 20. Plate Restriction Orifice Size 31/32” 10003261 21. Plate Restriction Orifice Size 1” 10003277 22. Plate Restriction Orifice Size 1 ¹⁄₃₂ ” 10003328 23. Plate Restriction Orifice Size 1 ¹⁄₁₆ ” 10003329 24. Plate Restricti ...

  • Vermont Casting 7PDVS - page 22

    D V Pow er V e nt S ystem 22 10003262 ...

  • Vermont Casting 7PDVS - page 23

    23 D V Pow er V e nt S ystem 10003262 ...

  • Vermont Casting 7PDVS - page 24

    2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Manufacturer Vermont Casting Category Indoor Fireplace

Documents that we receive from a manufacturer of a Vermont Casting 7PDVS can be divided into several groups. They are, among others:
- Vermont Casting technical drawings
- 7PDVS manuals
- Vermont Casting product data sheets
- information booklets
- or energy labels Vermont Casting 7PDVS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Casting 7PDVS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Casting 7PDVS, service manual, brief instructions and user manuals Vermont Casting 7PDVS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Casting 7PDVS.

Similar manuals

A complete manual for the device Vermont Casting 7PDVS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Casting 7PDVS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Casting 7PDVS.

A complete Vermont Casting manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Casting 7PDVS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Casting 7PDVS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Casting 7PDVS, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Casting 7PDVS - which should help us in our first steps of using Vermont Casting 7PDVS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Casting 7PDVS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Casting 7PDVS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Casting 7PDVS?

Use the form below

If you did not solve your problem by using a manual Vermont Casting 7PDVS, ask a question using the form below. If a user had a similar problem with Vermont Casting 7PDVS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)