English dropdown-ico

Manual EMI Volts/HZ/pH

28 pages 5.46 mb
Download

Go to site of 28

Summary
  • EMI Volts/HZ/pH - page 1

    S1C/S1H Single-Zone & S2C Dual-Zone SiDe DiSCHarge DuCtleSS Split SyStem ConDenSing unitS P/N# 240005897 Rev . B [05/08] Straight Cool/hea t pump S1C/S1h Nominal Circuit Capacities S1C/S1H: 9,000, 12,000, 18,000, 24,000 Btuh and S1C 30-36 Btuh Cooling onl y S2C Nominal Circuit Capacities: 9,000-12,000 Btuh Enviromaster International LLC 5780 Su ...

  • EMI Volts/HZ/pH - page 2

    www .enviromaster.com Side Discharge Condensers 2 inSt alla tion, opera tion anD maintenanCe manUal S1C/S1H Single-Zone & S2C DUal-Zone ConDenSing UnitS Shipping Damage MUST be Reported to the Carrier IMMEDIA TEL Y!!! Examine the exterior . Remove cover and examine compressor and piping for signs of damage. This manual is intended as an aid to ...

  • EMI Volts/HZ/pH - page 3

    www .enviromaster.com Side Discharge Condensers 3 proDUCt DeSCription The AmericaSeries S1C/H and S2C condensing units are, air-cooled, vertically arranged side discharge, high efciency units designed specically to meet or ex - ceed a 13 SEER rating. The S1C 9,000-36,000 Btuh and S1H 9, 000- 24, 000 Bt uh ca pac ity co nde ns ing u nit wil l ...

  • EMI Volts/HZ/pH - page 4

    www .enviromaster.com Side Discharge Condensers 4 itemS For ConSiDera tion • Locate the unit as close to the indoor section as possible. ( S ee T ubing Specications chart on pape 7.) • If the unit is used for low ambient cool - ing down to 32°F , this option must be specied to prevent system damage. • A void high trafc areas and pre ...

  • EMI Volts/HZ/pH - page 5

    www .enviromaster.com Side Discharge Condensers 5 inSt alla tion inStrUCtionS Unit moUnting inStrUCtionS Continued 5. Insert lag bolts through the holes in the bottom of the unit and tighten to secure. 6. Insert lag bolts through the holes in the feet on the back of the unit and tighten to secure. 7. Replace the front panel, do not tighten the side ...

  • EMI Volts/HZ/pH - page 6

    www .enviromaster.com Side Discharge Condensers 6 inSt alla tion inStrUCtionS c. Slide the side panel out to access the high/low electrical connections and wire diagram. Note: Remove the plastic edge guards from the holes and replace with a water- tight strain relief tting (High V) and a split grommet tting ( l ow V) 5. Power should be run to ...

  • EMI Volts/HZ/pH - page 7

    www .enviromaster.com Side Discharge Condensers 7 inSt alla tion inStrUCtionS 10. T o replace side panel slide the slotted holes of the panel onto the loosened screws of the front panel so that the edge of th e front pa nel cove rs th e edge of the side panel. eleCtriCal Wiring Continued 1 1. Fasten all remaining loose screws. reFrigerant piping Th ...

  • EMI Volts/HZ/pH - page 8

    www .enviromaster.com Side Discharge Condensers 8 Condenser Evaporator Figure 1 Condenser Evaporator 30' 15' p-trap inSt alla tion • A P-trap is recommended when the suc - tion riser is equal to or greater than 20 feet in height . • When the condenser is installed above the evaporator , the P-trap will help the return of oil back to t ...

  • EMI Volts/HZ/pH - page 9

    www .enviromaster.com Side Discharge Condensers 9 inSt alla tion inStrUCtionS reFrigerant piping Continued 2. Protect the valves by wrapping with a wet rag "heat sink" before brazing. 3. We recommend the use of a shield (can be made from some scrap metal) to protect the paint. 4. Braze tubing into ttings. 1. Clean the ends of tubing an ...

  • EMI Volts/HZ/pH - page 10

    www .enviromaster.com Side Discharge Condensers 10 inSt alla tion inStrUCtionS 9. Refer to Charts on page 12 to “ne tune” the refrigerant charge to meet your conditions. reFrigerant proCeSSing Complete piping ConneCtionS import ant noteS: 1. T o nd the charge adjustment and system charge for any evaporator and tubing length: Line Adjustme ...

  • EMI Volts/HZ/pH - page 11

    www .enviromaster.com Side Discharge Condensers 11 The units are delivered precharged with refrigerant for the condenser coil and the evaporator . Charging of the eld installed piping is required. Refer to the refrigerant charge table for the proper amount to be added for the applications interconect piping. Unit service valves are solid brass, ...

  • EMI Volts/HZ/pH - page 12

    www .enviromaster.com Side Discharge Condensers 12 Single Zone opera tion CHartS ...

  • EMI Volts/HZ/pH - page 13

    www .enviromaster.com Side Discharge Condensers 13 Single Zone opera tion CHartS ...

  • EMI Volts/HZ/pH - page 14

    www .enviromaster.com Side Discharge Condensers 14 Single Zone opera tion CHartS ...

  • EMI Volts/HZ/pH - page 15

    www .enviromaster.com Side Discharge Condensers 15 Single Zone opera tion CHartS ...

  • EMI Volts/HZ/pH - page 16

    www .enviromaster.com Side Discharge Condensers 16 Single Zone Hea t pUmp opera tion CHartS ...

  • EMI Volts/HZ/pH - page 17

    www .enviromaster.com Side Discharge Condensers 17 Single Zone Hea t pUmp opera tion CHartS ...

  • EMI Volts/HZ/pH - page 18

    www .enviromaster.com Side Discharge Condensers 18 DUal Zone opera tion CHartS ...

  • EMI Volts/HZ/pH - page 19

    www .enviromaster.com Side Discharge Condensers 19 opera tion anD maintenanCe The S1C/H and S2C outdoor sections are the compressor bearing units of the system. It operates at the command of the indoor section or room thermostat. Therefore, the system operation will be described in the manual pertaining to the indoor section. EMI units are designed ...

  • EMI Volts/HZ/pH - page 20

    www .enviromaster.com Side Discharge Condensers 20 Single-Zone anD DUal-Zone SeqUenCe oF opera tion Note: For remote wall mounted ther - mostat operation be sure to select EMI p/n 240004180 or a suitable 24 v , two sage heating, heat pump thermostat. Condenser operation: The transform - er locate d in the indo or unit pro vides 24V , low- v olt con ...

  • EMI Volts/HZ/pH - page 21

    www .enviromaster.com Side Discharge Condensers 21 DFT TST R and DF2 DeFroSt Control boarD teSting DeFroSt opera tion USing teSt pinS Single-Zone anD DUal-Zone SeqUenCe oF opera tion W arning! B ef or e re mo vi ng t he ac ce ss pa ne ls to the unit make sure that all power is dis - c on ne ct ed fr om th e un it . F ai lu re t o d o s o could resu ...

  • EMI Volts/HZ/pH - page 22

    www .enviromaster.com Side Discharge Condensers 22 moUnting DimenSionS model Size a b C D S1C/S1H 9, S1C/S1H 2 4 ⅝” 14 11 / 16 ” 3” 12 7 / 16 ” S1C/S1H 8, S1C/S1H 2 4 ⅝” 22 11 / 16 ” 3” 12 7 / 16 ” S1C 3, S1C 6 7” 23 15 / 16 ” 3” 12 7 / 16 ” Easy access interconnects on back of unit 1/2” Diameter Lag Holes a a b D C So ...

  • EMI Volts/HZ/pH - page 23

    www .enviromaster.com Side Discharge Condensers 23 NOtE: All EMI products are subject to ongoing development. Design and specications may change without notice. CAC WLC/WLH * Important - This system has been designed and manufactured to meet ENERGY ST AR criteria for energy efciency . However, proper refrigerant charge and proper air ow ar ...

  • EMI Volts/HZ/pH - page 24

    www .enviromaster.com Side Discharge Condensers 24 S1C/S1H Single Zone S1H eleCtriCal SpeCiFiCa tionS model # V olts/HZ/pH Fan motor Compressor t otal ampS min V olt m.C.a. HaCr brKr ampS Hp rla lra S1H9A 1 15/60/1 1.4 0.125 6.6 39.2 8.0 104 9.7 15 S1H2A 1 15/60/1 1.4 0.125 8.6 48.3 10.0 104 12.2 20 S1H9D 208/230/60/1 0.8 0.125 3.4 23.0 4.2 197 5.1 ...

  • EMI Volts/HZ/pH - page 25

    www .enviromaster.com Side Discharge Condensers 25 WLC CAC S2C Cooling SYStemS WitH S2C SiDe DiSCHarge Cassette Condenser btuh Seer SHr eer ref. CAC12 + CAC12 S2C99 18,000 13.0 .81 1 1.7 R22 CAC12 + CAC12 S2C22 23,000 13.0 .74 1 1.8 R22 CAC12 + CAC12 S2C92 21,000 13.0 .77 1 1.8 R22 Cooling SYStemS WitH S2C SiDe DiSCHarge W all Unit (s) C o n d e n ...

  • EMI Volts/HZ/pH - page 26

    www .enviromaster.com Side Discharge Condensers 26 The T est Unit Performance Data sheet below is provided for use by a qualied service professional in the event that there is a problem with the unit. In order for our T echnical Service Department to better serve you, please complete and have this information ready when calling. Make sure to inc ...

  • EMI Volts/HZ/pH - page 27

    www .enviromaster.com Side Discharge Condensers 27 emi’S proDUCt line inDoor UnitS oUtDoor UnitS S1C & S1H Single Zone Side Discharge S2C &S2H Dual Zone Side Discharge WLC/WLH High Wall Air Handler CAC/CAH Cassette Air Handler UNC/UNH Universal Floor or Ceiling Air Handler T2C, T3C, T4C and T2H, T3H, T4H; 2, 3 and 4 Zone T op Discharge ...

  • EMI Volts/HZ/pH - page 28

    Phone: 1-800-228-9364 Fax: 1-800-232-9364 5780 Success Drive, Rome, NY 13440 ...

Manufacturer EMI Category Ventilation Hood

Documents that we receive from a manufacturer of a EMI Volts/HZ/pH can be divided into several groups. They are, among others:
- EMI technical drawings
- Volts/HZ/pH manuals
- EMI product data sheets
- information booklets
- or energy labels EMI Volts/HZ/pH
All of them are important, but the most important information from the point of view of use of the device are in the user manual EMI Volts/HZ/pH.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EMI Volts/HZ/pH, service manual, brief instructions and user manuals EMI Volts/HZ/pH. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EMI Volts/HZ/pH.

Similar manuals

A complete manual for the device EMI Volts/HZ/pH, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EMI Volts/HZ/pH by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EMI Volts/HZ/pH.

A complete EMI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EMI Volts/HZ/pH - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EMI Volts/HZ/pH, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EMI Volts/HZ/pH, that we can find in the current document
3. Tips how to use the basic functions of the device EMI Volts/HZ/pH - which should help us in our first steps of using EMI Volts/HZ/pH
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EMI Volts/HZ/pH
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EMI Volts/HZ/pH in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EMI Volts/HZ/pH?

Use the form below

If you did not solve your problem by using a manual EMI Volts/HZ/pH, ask a question using the form below. If a user had a similar problem with EMI Volts/HZ/pH it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)