English dropdown-ico

Manual Icom IC-2800H

88 pages 0.74 mb
Download

Go to site of 88

Summary
  • Icom IC-2800H - page 1

    INSTR UCTION MANU AL This device complies with P ar t 15 of the FCC rules. Operation is sub- ject to the following tw o conditions: (1) This device may not cause harmful interference, and (2) this de vice must accept any interf erence received, including interf erence that may cause undesired operation. i2800H DU AL BAND FM TRANSCEIVER Downloaded b ...

  • Icom IC-2800H - page 2

    i FOREW ORD READ ALL INSTRUCTIONS carefully and completely bef ore using the transceiv er . SA VE THIS INSTRUCTION MANU AL — This in- struction manual contains impor tant operating instructions for the IC-2800H. EXPLICIT DEFINITIONS The e xplicit definitions belo w apply to this instruction man ual. CA UTIONS R W ARNING! NEVER connect the transc ...

  • Icom IC-2800H - page 3

    ii DO NO T operate the transceiv er near unshielded electrical blasting caps or in an e xplosive atmosphere. During mobile operation, DO NO T operate the transceiver without running the vehicle’ s engine. When transceiver po wer is ON and your v ehicle’ s engine is OFF , the vehicle’ s batter y will soon become e xhausted. A V OID using or pl ...

  • Icom IC-2800H - page 4

    1 SUPPLIED A CCESSORIES ......... 1 2 P ANEL DESCRIPTION ......... 2 – 13 ■ Controller unit ......................... 2 ■ Function display ...................... 4 ■ Basic function menu ............... 6 ■ Main unit ................................. 8 ■ HM-98 microphone ............... 10 ■ HM-97/118 microphone ........ 13 3 INST ALLA ...

  • Icom IC-2800H - page 5

    1 1 SUPPLIED A CCESSORIES The transceiv er comes with the following accessories. Qty . q DC power cab le (OPC-346) ........................................... 1 w Remote controller cable* 1 ............................................... 1 e Remote controller mounting brac ket (MB-73) ................. 1 r Main unit mounting brac ket .............. ...

  • Icom IC-2800H - page 6

    ■ Contr oller unit 2 2 P ANEL DESCRIPTION MAIN SCP SCP TS V/M H TS V/M H SCN M/C SCN M/C LO W MONI LO W MONI TOT RX TX MID-LO MID-LO SUB MAIN DUP SQL T PRIO DUP SQL T PRIO OFF M P M P 99 14 5 5.000 99 43 5 3.000 VO L VO L SQL SQL CHG/L PO WER MAIN Function display (p. 4) q w e rt y u o !0 !0 i Downloaded by Amateur Radio Directory  www.h ...

  • Icom IC-2800H - page 7

    3 2 P ANEL DESCRIPTION q VHF V OLUME CONTROL [V OL] Adjusts the VHF audio lev el. (p . 23) w VHF SQUELCH CONTR OL [SQL] ➥ Adjusts the VHF squelch lev el. (p . 23) ➥ Depending on the set mode setting, the RF attenuator is automatically activ ated when [SQL] is rotated clock- wise past the 12 o’clock position. (pgs. 23, 66) e VHF TUNING DIAL [D ...

  • Icom IC-2800H - page 8

    4 2 P ANEL DESCRIPTION ■ Function displa y q FUNCTION INDICA T ORS (pgs. 6, 7) Indicate the functions assigned to the m ulti-function s witches at left. w DTMF MEMOR Y ENCODER INDICA TOR (p. 54) Appears when the DTMF memor y encoder is in use. e LOCK INDICA T OR (p . 19) Appears when the lock function is in use . r TIME-OUT TIMER INDICA T OR (p. ...

  • Icom IC-2800H - page 9

    5 2 P ANEL DESCRIPTION o FREQUENCY READOUT Shows the operating frequency , memor y name, etc. !0 PRIORITY W A TCH INDICA T OR (p. 48) Appears when prior ity watch is in use . !1 T ONE INDICA T ORS (pgs. 26, 50, 52) “T” appears when the subaudible tone encoder is in use; “T SQL ì ” appears during pock et beep operation and “T SQL ” appe ...

  • Icom IC-2800H - page 10

    6 2 P ANEL DESCRIPTION ■ Basic function menu The multi-function s witches hav e 2 main menus. Pushing [CHG/L] toggles between the 2 multi-function s witch menus. Left-hand s witches are used f or VHF band and right-hand s witches are used for UHF band e xcept i and o . MAIN SCP MAIN SCP V/M H TS V/M H TS M/C SCN M/C SCN MONI LO W MONI LO W MID-LO ...

  • Icom IC-2800H - page 11

    7 2 P ANEL DESCRIPTION r MONIT OR/LO W PO WER MENU [MONI (LO W)] ➥ Push to toggle the monitor function ON and OFF . (p. 24) ➥ Push for 2 sec. to change the output power selection. (p. 25) • Lo w (LO), mid-lo w (MID-LO), mid-high (MID-HI) and high (HI) powers are a vailable. t MAIN B AND/MEMOR Y EDIT MENU [MAIN (EDIT)] ➥ Push to select the m ...

  • Icom IC-2800H - page 12

    8 2 P ANEL DESCRIPTION ■ Main unit q MICROPHONE CONNECT OR [MIC] Connects the supplied microphone. w CONTROLLER CONNECT OR [CONTROLLER] (p. 16) Connects the controller unit with the supplied cable . e D A T A CONNECT OR [DA T A] (p . 70) Connects a TNC (T erminal Node Controller), etc. for data communications. • See the inf or mation at right f ...

  • Icom IC-2800H - page 13

    y PO WER RECEPT ACLE [DC13.8V] (pgs. 15, 16) Accepts 13.8 V DC ±15% with the supplied DC pow er cable . • Current of 12 A or greater is required. DO NO T use a cigarette lighter sock et as a power source when operating in a v ehicle. The plug may cause voltage drops and ignition noise ma y be superimposed onto transmit or receiv e audio. u ANTEN ...

  • Icom IC-2800H - page 14

    ■ HM-98 micr ophone * q UP/DO WN SWITCHES [ Y Y ]/[ Z Z ] ➥ Push either s witch to change the operating frequency , memor y channel, set mode contents, etc. (p . 20) ➥ Push either s witch for 2 sec. to star t scanning. (p. 43) w PTT SWITCH ➥ Push and hold to transmit; release to receive. (p . 24) ➥ T oggles betw een transmitting and recei ...

  • Icom IC-2800H - page 15

    11 2 P ANEL DESCRIPTION KEY FUNCTION SECOND ARY FUNCTION (after ) FUNC O THER FUNCTIONS AFC 1 MONI T oggles betw een opening and closing the operating band’ s squelch. (p . 24) No secondar y function. After : T r ansmit the appropriate DTMF code or push [0] to [9], [A] to [D] to trans- mit the DTMF memory contents when the DTMF memor y encoder is ...

  • Icom IC-2800H - page 16

    12 2 P ANEL DESCRIPTION KEY FUNCTION SECOND ARY FUNCTION (after ) FUNC O THER FUNCTIONS MW A CLR • Clears a digit before entry . (p . 22) • Cancels the monitor , scan, prior ity watch, DTMF memor y , mute function or set mode condition. (pgs. 24, 42, 48, 54) • Writes the VFO contents into the memor y channel or call channel. (pgs. 34, 39) • ...

  • Icom IC-2800H - page 17

    13 2 P ANEL DESCRIPTION ■ HM-97/118 micr ophone q PTT SWITCH Push and hold to transmit; release to receive. (p . 24) w UP/DO WN SWITCHES [UP]/[DN] ➥ Push either s witch to change the operating frequency , memor y channel, set mode contents, etc. (p . 20) ➥ Push either s witch for 2 sec. to star t scanning. (p. 42) ➥ Activate a function prog ...

  • Icom IC-2800H - page 18

    14 3 INST ALLA TION ■ Location Select a location which can suppor t the w eight of the trans- ceiver and does not interf ere with driving in any wa y . We rec- ommend the locations shown in the diagr am below . NEVER place the transceiv er or remote controller where nor- mal operation of the v ehicle may be hindered or where it could cause bodily ...

  • Icom IC-2800H - page 19

    15 3 INST ALLA TION ■ Mounting the remote contr oller Install the nut bef ore attaching the bracket to the w all, etc. D When using an optional MB-65 The supplied remote con- troller brac ket is not nec- essar y when using the optional MB-65. ■ Battery connection NEVER connect the transceiv er directly to a 24 V battery . DO NO T use the cigare ...

  • Icom IC-2800H - page 20

    16 3 INST ALLA TION ■ DC power suppl y connection Use a 13.8 V DC power supply with more than 12 A capacity . Make sure the ground terminal of the DC power supply is grounded. • See p . 74 for fuse replacement. ■ Cable connection Connect the cable as sho wn below . DC power supply 13.8 V to an AC outlet Fuses 20 A + red + _ _ black Battery Re ...

  • Icom IC-2800H - page 21

    ■ Antenna installation D Antenna location T o obtain maxim um perf ormance from the transceiver , select a high-quality antenna and mount it in a good location. A non- radial antenna should be used when using a magnetic mount. D Antenna connector The antenna uses a PL-259 connector . 17 3 INST ALLA TION Roof-mount antenna (Drill a hole or use a m ...

  • Icom IC-2800H - page 22

    18 4 FREQUENCY SETTING ■ Preparation D T urning po wer ON/OFF Bef ore operating the transceiv er for the first time it’ s a good idea to reset the transceiv er’ s CPU . This will ensure that all transceiv er settings are at their def aults. See p. 75 for CPU resetting details. ➥ Push [PO WER] f or 2 sec. to tur n power ON or OFF . D Operat ...

  • Icom IC-2800H - page 23

    ■ Loc k functions T o pre vent accidental frequency changes and unnecessary function access, use the loc k function. The transceiver and HM-98 hav e 2 different loc k functions. D Frequency loc k This function locks the tuning dials and s witches electronically and also locks the microphone s witches. ➥ Push [CHG/L] f or 2 sec. to toggle the fr ...

  • Icom IC-2800H - page 24

    20 4 FREQUENCY SETTING ■ Using the tuning dial q Select VFO mode with the desired band’ s [V/M H ]. • Push [CHG/L] if [V/M H ] is not display ed. w Rotate desired band’ s [DIAL] to change the frequency . • The frequency changes according to the selected tuning steps . See the next page f or selecting the tuning step. D 1 MHz tuning step P ...

  • Icom IC-2800H - page 25

    ■ Setting a tuning step T uning steps can be selected f or each band. This transceiver has 8 tuning steps as f ollows: • 5 kHz • 10 kHz • 12.5 kHz • 15 kHz • 20 kHz • 25 kHz • 30 kHz • 50 kHz q Select VFO mode with the desired band’ s [V/M H ]. • Push [CHG/L] if [V/M H ] is not display ed. w Push [ (V/M H ) TS] f or 2 sec. to ...

  • Icom IC-2800H - page 26

    ■ Using the keypad The frequency can be directly set via numeral ke ys on the HM-98 microphone. q Push [BAND] to select the desired operating band. w Push [VFO] to select VFO mode, if necessary . e Push [ENT] to activate the k eypad f or digit input. r Push 6 ke ys to input a frequency . • When a digit is mistak enly input, push [ENT] to clear ...

  • Icom IC-2800H - page 27

    ■ Receiving q Push [PO WER] for 2 sec. to turn power ON. w Set the audio le vel. ➥ Push the desired band’ s [MONI] to open the squelch. • Push [CHG/L] if [MONI] is not displa yed. ➥ Rotate the desired band’ s [V OL] control to adjust the audio output le vel. ➥ Push [MONI] again to close the squelch. e Set the squelch le vel. ➥ Rotat ...

  • Icom IC-2800H - page 28

    24 5 BASIC OPERA TION ■ Monitor function This function is used to listen to weak signals without disturb - ing the squelch setting or to open the squelch manually e ven when mute functions such as the tone squelch are in use. ➥ Push the desired band’ s [MONI] to toggle the monitor func- tion ON and OFF . • While duple x is ON for repeater o ...

  • Icom IC-2800H - page 29

    25 5 BASIC OPERA TION ■ Selecting output power The transceiv er has 4 output po w er le vels to suit y our oper at- ing requirements. Low output powers during shor t-distance communications ma y reduce the possibility of interference to other stations and will reduce current consumption. ➥ Push the desired band’ s [ (MONI) LOW] f or 2 sec. on ...

  • Icom IC-2800H - page 30

    ■ Accessing a repeater When using a repeater , the transmit frequency is shifted from the receive frequency b y the offset frequency . (p. 30) It is con- venient to prog ram repeater inf ormation into memor y chan- nels. (p . 32) q Select the desired band with the desired band’ s [MAIN]. w Set the receiv e frequency (repeater output frequency). ...

  • Icom IC-2800H - page 31

    27 6 REPEA TER OPERA TION q Select the desired band with [BAND]. w Set the receive frequency (repeater output fre- quency). e Push [ u DUP–] to select –duple x; push [ i DUP+] f or +duplex. r Push [FUNC] then [ u T ONE] to tur n ON the subaudible tone encoder according to repeater requirements. • Ref er to p. 29 for tone frequency setting. ? ...

  • Icom IC-2800H - page 32

    28 6 REPEA TER OPERA TION ■ 1750 Hz tone A 1750 Hz tone is required to access most European re - peaters. The microphone has 1750 Hz tone capability . D Using the HM-98 microphone q Push [BAND] to select the desired band. w Push [FUNC]. • The mode indicator lights orange . e Push [ B T ONE-1] to transmit a 1750 Hz tone call signal f or 0.5 sec. ...

  • Icom IC-2800H - page 33

    29 6 REPEA TER OPERA TION ■ Subaudible tone (encoder function) Some repeaters require subaudible tones to be accessed. Subaudible tones are superimposed ov er your normal signal and must be set in adv ance. Each operating band and each memor y channel hav e inde- pendent settings. q Select the mode/channel y ou wish to set the subaudib le tone en ...

  • Icom IC-2800H - page 34

    30 6 REPEA TER OPERA TION ■ Offset frequency When communicating through a repeater , the transmit fre- quency is shifted from the receiv e frequency by an amount determined by the offset frequency . q Select the mode/channel you wish to set the offset fre- quency to , such as VFO mode or memor y/call channel. w Push the desired band’ s [ (MAIN) ...

  • Icom IC-2800H - page 35

    31 6 REPEA TER OPERA TION ■ A uto repeater function (U .S.A. and Korea versions onl y) The U .S.A. and K orea versions automatically activ ate the re- peater settings (duple x ON/OFF , duplex direction, tone en- coder ON/OFF) when the operating frequency f alls within or outside of the general repeater output frequency range . The offset and repe ...

  • Icom IC-2800H - page 36

    ■ General The transceiv er has 99 memor y channels and 1 call channel f or each band for stor age of often-used frequencies. D Memory/call channel contents The follo wing information can be programmed into memor y or call channels: • Operating frequency (p . 20) • Operating mode (p . 74) • 8-character memory name (p. 37) • T uning step (p ...

  • Icom IC-2800H - page 37

    33 7 MEMOR Y/CALL CHANNELS ■ Pr ogramming after selection q Select memor y mode with the desired band’ s [M/C]. • Push [CHG/L] if [M/C] is not displa yed. •“ ! ” appears when memor y mode is selected. w Set the memor y channel to be programmed with the de- sired band’ s tuning dial. e Push [V/M H ] to select VFO mode. r Set the desire ...

  • Icom IC-2800H - page 38

    34 7 MEMOR Y/CALL CHANNELS ■ Pr ogramming during selection via the micr ophone The HM-98 microphone can also be used to pro- gram memory channels. q Select the desired band with [BAND]. w Select VFO mode with [VFO]. e Set the desired frequency . • Set other data (e.g. offset frequency , duplex direction, subaudible tone frequency , etc.), if re ...

  • Icom IC-2800H - page 39

    35 7 MEMOR Y/CALL CHANNELS ■ T ransferring memory contents to another memory via the micr ophone The HM-98 microphone can also be used to trans- f er memor y channels. q Select the desired band with [BAND]. w Select memor y mode with [MR]. e Set the desired memory channel to be transf erred with [ Y ] or [ Z ]. r Push [FUNC] then [ E MW] momentar ...

  • Icom IC-2800H - page 40

    36 7 MEMOR Y/CALL CHANNELS ■ Memory clear Unwanted memory channels can be cleared (erased). Before clearing a memor y channel make sure it is no longer needed as cleared memories cannot be recalled. q Push the desired band’ s [S.MW] momentarily . • Push [CHG/L] if [S.MW] is not displa yed. • Do not hold [S .MW] for more than 0.5 sec., other ...

  • Icom IC-2800H - page 41

    37 7 MEMOR Y/CALL CHANNELS ■ Alphanumeric displa y Each memory channel and the call channel can be pro- grammed with an alphan umeric name such as a repeater name, club name , etc., f or easy recognition. Names can be a maximum of 8 characters—see the tab le at r ight f or a vailable characters. Scan edge channels and scratch pad memories CANNO ...

  • Icom IC-2800H - page 42

    38 7 MEMOR Y/CALL CHANNELS ■ Call channel 1 call channel is a v ailab le for each band to store a most-often- used frequency f or quick recall. D Selecting a call channel q Push [M/C] to select a call chan- nel. • Push [CHG/L] if [M/C] is not dis- play ed. • “C” appears when call channel is selected. w Push [V/M H ] to select VFO mode, if ...

  • Icom IC-2800H - page 43

    39 7 MEMOR Y/CALL CHANNELS D Programming a call c hannel via the microphone The HM-98 microphone can also be used to pro- gram a call channel. q Select the desired band with [BAND]. w Select VFO mode with [VFO]. e Set the desired frequency . • Set other data (e.g. offset frequency , duplex direction, subaudible tone frequency , etc.), if required ...

  • Icom IC-2800H - page 44

    40 8 SCRA TCH P AD MEMOR Y ■ What is a scratch pad memory? During VFO operation, the transceiver automatically memo - rizes operating frequency inf or mation, separate from regular memor y channels, when transmitting on a ne w frequency . There are 2 types of scratch pad memories , those f or simplex operation, L1–L5, and those f or duplex (rep ...

  • Icom IC-2800H - page 45

    41 8 SCRA TCH P AD MEMOR Y q Select the desired band with [BAND]. w Push [ (MR) CALL] f or 2 sec. to select the se- lected band’ s call channel. e Push [ Y ] one or more times to select a duplex scratch pad memory; push [ Z ] one or more times to select a simple x scratch pad memory . r Push [MR] or [VFO] to e xit the scratch pad memor y . ■ T ...

  • Icom IC-2800H - page 46

    MEMOR Y SCAN (p . 45) Repeatedly scans memory channels e xcept those set as skip channels. Used to search through often-used memories and f or bypassing normally busy channels such as re - peater frequencies. FULL/B AND SCAN (p. 43) Repeatedly scans all frequen- cies ov er the entire band. Used as the simplest scan without any preliminary set- ting ...

  • Icom IC-2800H - page 47

    43 9 SCAN OPERA TION ■ Full/pr ogrammed scan q Select VFO mode with the desired band’ s [V/M H ]. • Push [CHG/L] if [V/M H ] is not display ed. w Make sure the squelch is set to the threshold point. e Push [ (M/C) SCN] for 2 sec. to enter scan screen. • If the poc k et beep function is activated, the transceiv er automat- ically selects the ...

  • Icom IC-2800H - page 48

    ■ Selecting scan edges The scanning range can be set to all frequencies (full scan) or between two user-programmed frequencies (progr ammed scan). Scan edges can be programmed in the same manner as memor y channels. Scan edges are programmed into scan edges, 1A/1B to 3A/3B , in memor y channels. (p. 32) q Push [ (M/C) SCN] for 2 sec. to enter the ...

  • Icom IC-2800H - page 49

    45 9 SCAN OPERA TION ■ Memory scan q Select memor y mode with the desired band’ s [M/C]. • Push [CHG/L] if [M/C] is not displa yed. •“ ! ” appears when memor y mode is selected. w Make sure the squelch is set to the threshold point. e Push [ (M/C) SCN] for 2 sec. to enter the scan screen. • If the poc k et beep function is activated, ...

  • Icom IC-2800H - page 50

    46 9 SCAN OPERA TION ■ Skip channel setting Memor y channels can be set to be skipped f or memor y skip scan. In addition, memor y channels can be set to be skipped f or both memory skip scan and full/band/programmed scan (frequency skip scan). This is useful to speedup the scan in- ter v al. q Select a memor y channel you wish to set skip inf or ...

  • Icom IC-2800H - page 51

    47 10 B AND SCOPE ■ Operation The band scope function allows you to visually chec k a spec- ified frequency range. Sweep range varies ±50 kHz through ±500 kHz with setting of the s weep tuning steps. Receive audio is m uted while monitor ing the band scope. Push [SWP] to cancel s weeping and receiv e the audio . q Set the desired frequency as ...

  • Icom IC-2800H - page 52

    ■ Priority watch types Prior ity watch checks f or signals on a frequency ev er y 5 sec. while operating on a VFO frequency . The transceiver has 2 prior ity watch types to suit y our needs. The watch resumes according to the selected scan resume condition. See p. 46 for details . ■ Priority watch operation q Select VFO mode with the desired ba ...

  • Icom IC-2800H - page 53

    49 11 PRIORITY W A TCH y Push [ (MEM ) PRIO] for 2 sec. to star t the watch. • The tr ansceiver chec ks the memor y or call channel frequency ev er y 5 sec. • The watch resumes according to the selected scan resume con- dition. (p . 46) • “PRIO” and decimal point blinks while receiving a signal on a watch channel. u Push [ (MEM ) PRIO] wh ...

  • Icom IC-2800H - page 54

    50 12 SUB A UDIBLE T ONE OPERA TION ■ T one squelch operation The tone squelch opens only when receiving a signal con- taining a matching subaudible tone. Y ou can silently wait for calls from group members using the same tone. q Select the desired band with the desired band’ s [MAIN]. w Set an operating frequency . e Set the desired CTCSS tone ...

  • Icom IC-2800H - page 55

    51 12 SUBA UDIBLE T ONE OPERA TION D Setting subaudible tones f or tone squelch operation (CTCSS tones) Separate tone frequencies can be set f or tone squelch oper- ation than f or repeater operation (the same range of tones is av ailable). Like repeater tones , these are set in the edit screen. q Select the mode/channel you wish to set the CTCSS t ...

  • Icom IC-2800H - page 56

    52 12 SUBA UDIBLE T ONE OPERA TION ■ P o c ket beep operation This function uses subaudible tones f or calling and can be used as a “common pager” to inf orm you that someone has called while you w ere aw a y from the transceiv er . D W aiting for a call fr om a specific station q Select the desired band with the desired band’ s [MAIN]. w ...

  • Icom IC-2800H - page 57

    53 12 SUBA UDIBLE T ONE OPERA TION ■ T one scan The transceiv er can detect the subaudib le tone frequency in a received signal. By monitoring a signal that is being transmit- ted on a repeater input frequency , you can determine the tone frequency required to access the repeater . q Set the desired frequency or memory channel to be check ed for ...

  • Icom IC-2800H - page 58

    ■ Pr ogramming a DTMF code DTMF codes are used for autopatching, accessing repeaters, controlling other equipment, etc. The transceiver has 14 DTMF memory channels (D0–D9, DA–DD) f or storage of often-used DTMF codes of up to 16 digits. q Push [DTMF] f or 2 sec. to select the DTMF memory screen. • Push [CHG/L] if [DTMF] is not displa yed. w ...

  • Icom IC-2800H - page 59

    ■ T ransmitting a DTMF code D A utomatic transmission (DTMF memor y) The selected DTMF code is transmitted at each push of the PTT s witch when the DTMF memor y encoder is turned ON. q Push [DTMF] to turn the DTMF memor y encoder ON. • Push [CHG/L] if [DTMF] is not displa yed. • “ ” appears. w Push [DTMF] f or 2 sec. to select the DTMF me ...

  • Icom IC-2800H - page 60

    ■ DTMF speed The rate at which DTMF memories send individual DTMF characters can be set to accommodate operating needs . q Push [DTMF] f or 2 sec. to select the DTMF memory screen. • Push [CHG/L] if [DTMF] is not displa yed. w Push [TIME] one or more times to select the desired speed as shown in the tab le below . e Push [ ï ] to e xit the DTM ...

  • Icom IC-2800H - page 61

    ■ Connection Wireless remote control is av ailable when the f ollowing op- tions are used. ➧ HM-90 WIRELESS MICROPHONE ➧ EX-1759 INFRARED RECEIVER D Recommended connection ■ HM-90 wireless micr ophone The HM-90’ s inter nal battery should be charged when the mi- crophone is not being held. Charging period : 1.5 hr. with timer (or 8 hr . w ...

  • Icom IC-2800H - page 62

    58 14 WIRELESS OPERA TION ■ EX-1759 installation The EX-1759 INFRARED RECEIVER can be installed f or 2 diff er- ent pur poses depending on the HM-90 charger . This is be - cause the EX-1759 has both an infrared receiv er and a microphone connector which contains microphone charging capabilities. When using the IC-2800H main unit Attach the EX-175 ...

  • Icom IC-2800H - page 63

    ■ HM-90 switc hes q PTT SWITCH ➥ Push and hold to transmit; release to receive. ➥ T oggles betw een transmitting and receiving while the one-touch PTT function is in use. w B AND SWITCHES [BAND SELECT Y Y , Z Z ] ➥ Push to select the operating band. ➥ Activate the sub band access function after pushing [FUNC] on the HM-90 rear panel. e MO ...

  • Icom IC-2800H - page 64

    60 14 WIRELESS OPERA TION KEY FUNCTION Selects the call channel. Selects memor y mode. Selects VFO mode. Selects high output power . Selects mid-high output power . Selects low output po wer . Selects –duple x. Selects +duple x. Selects simple x. Mutes audio signals. SECOND AR Y FUNCTION (after ) No secondar y function. No secondar y function. T ...

  • Icom IC-2800H - page 65

    61 14 WIRELESS OPERA TION KEY FUNCTION Clears a digit bef ore entr y . Cancels the scan, priority watch, or DTMF memor y function. Enters set mode and adv ances the set mode selection order . Decreases the set mode selection order after entering set mode. NO TE: The IC-2800H has no voice synthesiz er function. Sets the ke ypad for numeral input. T ...

  • Icom IC-2800H - page 66

    62 14 WIRELESS OPERA TION ■ Micr ophone address The transceiv er has 8 possible microphone addresses (in- cluding OFF) to help pre vent interf erence from other HM-90 wireless microphones. Set both the microphone address and microphone dip s witch to the same value as f ollows. When the supplied microphone is connected, the trans- ceiver rejects ...

  • Icom IC-2800H - page 67

    63 15 O THER FUNCTIONS ■ Beep tones Y ou can select silent operation by turning beep tones OFF or you can select to ha ve confirmation beeps sound at the push of a s witch by turning beep tones ON. q Push [ (DISP) SET] f or 2 sec. to enter set mode. • Push [CHG/L] if [(DISP) SET] is not displa yed. w Push [ Y ] to select the ‘Operation Beep? ...

  • Icom IC-2800H - page 68

    64 15 O THER FUNCTIONS ■ A uto power -off function The transceiv er can be set to automatically tur n OFF after a specified period in which no operations are performed. 2 hours, 1 hour , 30 min. and OFF can be specified. The spec- ified period is retained even when the transceiv er is tur ned OFF by the auto po wer-off function. T o cancel the ...

  • Icom IC-2800H - page 69

    65 15 O THER FUNCTIONS ■ Squelch dela y During operation, received signal strength often fluctuates. This can result in annoying repeated opening and closing of the squelch during reception of the same signal. The trans- ceiver has a b uilt-in squelch delay function which helps pre- vent this . When both stations are oper ating from a fixed locat ...

  • Icom IC-2800H - page 70

    66 15 O THER FUNCTIONS ■ Sub band b usy beep The sub band b usy beep sounds when the sub band’ s squelch is closed to inf or m y ou that the sub band’ s squelch has been opened. q Push [ (DISP) SET] f or 2 sec. to enter set mode. • Push [CHG/L] if [(DISP) SET] is not displa yed. w Push [ Y ] or [ Z ] to select the ‘Sub Band Beep’ item. ...

  • Icom IC-2800H - page 71

    67 15 O THER FUNCTIONS ■ Memory name indication The transceiv er can display memor y names programmed in memor y or call channels. (p. 32) q Push [ (DISP) SET] f or 2 sec. to enter set mode. • Push [CHG/L] if [(DISP) SET] is not displa yed. w Push [ Y ] or [ Z ] to select the ‘Memor y Name’ item. • Left-hand tuning dial can also select th ...

  • Icom IC-2800H - page 72

    68 15 O THER FUNCTIONS ■ HM-97/118 [UP]/[DN] keys Switches on the transceiv er’s front panel can be assigned to the HM-97/118 [UP] and [DN] ke ys. The f ollowing can be as- signed: V/U MAIN : [MAIN (SCP)] V/U V/MHz : [V/M H (TS)] V/U M/C : [M/C (SCN)] V/U MONI : [MONI (LO W)] V/U EDIT : [MAIN (EDIT)] V/U TONE : [TON (DUP)] V/U MW : [S.MW (MW)] ...

  • Icom IC-2800H - page 73

    69 15 O THER FUNCTIONS ■ Displa y brightness The brightness of the LCD can be adjusted from 0% to 100% in 3 or 4% steps. Adjust brightness to suit lighting conditions and personal pref erences. q Push [DISP] to enter displa y set mode. • Push [CHG/L] if [DISP] is not displa yed. w Push [ Y ] or [ Z ] to select the ‘Bright’ item. • Left-ha ...

  • Icom IC-2800H - page 74

    70 15 O THER FUNCTIONS ■ P acket operation D Data speed F or pac k et operation, the transceiv er can be set to one of tw o data speeds: 1200 bps (def ault) or 9600 bps. q Push [ (DISP) SET] f or 2 sec. to enter set mode. • Push [CHG/L] if [(DISP) SET] is not displa yed. w Push [ Y ] or [ Z ] to select the ‘P acket BPS’ item. • Left-hand ...

  • Icom IC-2800H - page 75

    71 15 O THER FUNCTIONS D 1200 bps packet operation q Connect the transceiv er and a TNC as illustr ated below . w Set the TNC for transmit. e Set transmit dela y on the TNC to 30–50. r Adjust the TNC frequency deviation if necessary . • When using a deviation meter: Adjust the output of the TNC so that frequency deviation is in the range ± 3 t ...

  • Icom IC-2800H - page 76

    72 15 O THER FUNCTIONS D 9600 bps high speed packet operation The transceiv er supports 2 modes of 9600 bps pack et oper a- tion: G3R UH and GMSK. q Connect the transceiv er and a TNC as illustr ated below . w G3R UH mode can handle 16 kinds of modulated wav e f orms in order to maintain a communication link. e Set transmit dela y on the TNC to 30? ...

  • Icom IC-2800H - page 77

    73 15 O THER FUNCTIONS D Adjusting the transmit signal output from the TNC When setting data transmission speed to 9600 bps, the data signal coming from the TNC is applied exclusiv ely to the in- ternal limiter circuitr y to automatically maintain band width. NEVER apply data lev els from the TNC of ov er 0.6 V p-p , oth- erwise the transceiver wil ...

  • Icom IC-2800H - page 78

    74 15 O THER FUNCTIONS ■ Demonstration displa y A demonstration function is a v ailable at pow er ON. This func- tion gives y ou a quick visual introduction to the function dis- pla y indicators. q While pushing [CHG/L], push [PO WER] to tur n power ON. • The transceiv er cycles through a visual tour of the function dis- play indicators . w Pus ...

  • Icom IC-2800H - page 79

    75 15 O THER FUNCTIONS ■ P ar tial reset If you w ant to initialize the operating conditions (VFO fre- quency , VFO settings, set mode contents) without clearing the memor y contents, a partial resetting function is availab le for the transceiv er. Band conditions can be reset independently . D VHF band partial resetting ➥ While pushing the 2nd ...

  • Icom IC-2800H - page 80

    ■ Getting star ted D This cloning software is designed to perf orm data setting and cloning f or the IC-2800H DU AL BAND FM transceiver . D HELP WINDOW: Each item has a help window to describe functions and operation. ■ System requirements T o use this prog r am, the f ollowing hardware and softw are are required: • IBM PC/A T compatib le com ...

  • Icom IC-2800H - page 81

    ■ COM por t/call sign setting • Set the com por t (RS-232C por t) number properly . • Enter your call sign. NO TE: ‘Check the follo wing’ dialog box appears when the RS-232C serial por t is not set correctly . NO TE: When first using this software, read out all the transceiv er cloning data into the PC bef ore star ting editing with this ...

  • Icom IC-2800H - page 82

    t CLONING MENU [Cloning] Push to displa y cloning menu and cloning inf or mation dia- log bo x. y HELP MENU [Help] Push to displa y one point help , help contents, cloning soft- ware re vision information. u T ool bar Shor t cut ke y appears on the tool bar when clic king the tool bar function in the [View] men u. ■ Edit menu The ‘Edit Memor y ...

  • Icom IC-2800H - page 83

    ■ Common settings There are 3 setting menus a vailab le. Common : Commonly set items such as oper ation beeps, sub band m ute, sub band beep , RF attenuator , name display , T O T , auto repeater , auto pow er-off , cooling f an setting, packet data speed, squelch delay , VHF/UHF scan re- sume timer and RF output power settings . Display : Sets L ...

  • Icom IC-2800H - page 84

    80 17 TR OUBLESHOO TING PROBLEM POSSIBLE CA USE SOLUTION REF . No power comes on. • Po wer connector has a poor contact. • P olarity of the power connection is rev ersed. • Blown fuse . • Check the connector pins . • Reconnect the po wer cable observing the proper polarity . Replace the fuse, if damaged. • Check the cause , then replace ...

  • Icom IC-2800H - page 85

    HM-90 WIRELESS MICROPHONE Infrared, full remote control microphone . Wired remote control is also possible . EX-1759 INFRARED RECEIVER Used to receive control signals from the HM-90. EX-1513 INFRARED SUB RECEIVER Used with the EX-1759 to extend the controllab le area. HM-98 REMO TE CONTROL MICROPHONE Wired remote control microphone with ke y backli ...

  • Icom IC-2800H - page 86

    82 19 SPECIFICA TIONS D General • F requency cover age : (Unit: MHz) U .S.A. T r ansmit 144–148, 430–450* 1 Receive 118–174* 2 , 430–450* 1 S. America T ransmit 144–148, 430–440 Receive 118–174* 2 , 400–530* 3 Europe, Tx/Rx 144–146, 430–440 Ta i w a n Italy T ransmit 144–148, 430–440 Receive 136–174* 2 , 400–530* 3 Asi ...

  • Icom IC-2800H - page 87

    83 19 SPECIFICA TIONS D Receiver • Receive system : Double con version superhetero- dyne • Inter mediate frequencies : 1st VHF 15.65 MHz UHF 46.05 MHz 2nd 450 kHz • Sensitivity : 0.16 µV typical (at 12 dB SINAD) • Squelch sensitivity : Less than 0.13 µV (at threshold) • Selectivity : Wide More than 12 kHz/–6 dB Less than 28 kHz/–60 ...

  • Icom IC-2800H - page 88

    Count on us! 6-9-16 Kamihigashi, Hirano-ku, Osaka 547-0002 J apan A-5570H-1EX- q Printed in Japan © 1999 Icom Inc. Downloaded by Amateur Radio Directory  www.hamdirectory.info ...

Manufacturer Icom Category Marine Radio

Documents that we receive from a manufacturer of a Icom IC-2800H can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-2800H manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-2800H
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-2800H.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-2800H, service manual, brief instructions and user manuals Icom IC-2800H. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-2800H.

Similar manuals

A complete manual for the device Icom IC-2800H, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-2800H by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-2800H.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-2800H - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-2800H, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-2800H, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-2800H - which should help us in our first steps of using Icom IC-2800H
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-2800H
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-2800H in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-2800H?

Use the form below

If you did not solve your problem by using a manual Icom IC-2800H, ask a question using the form below. If a user had a similar problem with Icom IC-2800H it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)