English dropdown-ico

Manual Kicker CX1200.1

28 pages 1.22 mb
Download

Go to site of 28

Summary
  • Kicker CX1200.1 - page 1

    CX MONO AMPLIFIERS CX300.1 | CX600.1 | CX1200.1 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.1 Benutzerhandbuch | Deutsch MONOVERSTÄRKER DER CX.1-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.1 CX Amplifiers 2012 CX Mono Amps Rev I.indd 1 2012 CX Mono Amps Rev I.indd 1 6/22/2012 2 ...

  • Kicker CX1200.1 - page 2

    2 CX.1-SERIES AMPLIFIERS OWNER’S MANUAL INST ALLA TION Mounting: Choose a structurally sound location to mount your KICKER amplifi er . Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er . If possible, mount the amplifi er in th ...

  • Kicker CX1200.1 - page 3

    3 Wiring: Disconnect the vehicle’ s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er . Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’ s chassis. Adding an additional ground wire of this same gauge (or larger) between the batt ...

  • Kicker CX1200.1 - page 4

    4 GND REM +12V 12V battery external fuse remote turn-on (see page 5) bare-metal chassis ground bare-metal chassis ground  18” (45cm)  24” (60cm) woofer MONO OPERA TION minimum impedance of 2 ohms Model External Fuse (sold separately) Power/Ground W ire KICKER W iring Kit CX300.1 1 x 40 Ampere 8 Gauge PK8, ZCK84 CX600.1 1 x 80 Ampere 4 Gau ...

  • Kicker CX1200.1 - page 5

    5 OPERA TION Automatic T ur n-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC Offset. • Remote T urn-On: Run 18 gauge wire from the Remote T urn-On Lead on your source unit to the terminal labeled REM between the amplifi er ’ s positive and negative power terminals. This is the preferred automatic turn-on ...

  • Kicker CX1200.1 - page 6

    6 CXRC REMOTE BASS INST ALLA TION Surface-mount the CXRC remote using the supplied screws. Connect the supplied 1/8th inch [3.5mm] patch cable to the CXRC remote and the Remote Bass jack on the amplifi er back view TROUBLESHOOTING If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incor ...

  • Kicker CX1200.1 - page 7

    7 KICKER will now provide a thr ee- year warranty with all CX-Series Amplifi er purchases paired with a qualifying KICKER Installation Kit* . This extends the standard warranty by an additional year . Amplifi er and Kit must be purchased from an Authorized KICKER Dealer . KICKER CX amplifi er success is currently at an unheard-of rate, making th ...

  • Kicker CX1200.1 - page 8

    8 Modelo: CX300.1 CX600.1 CX1200.1 Alimentación RMS @ 14.4V , 4  mono,  1% THD+N @ 14.4V , 2  mono,  1% THD+N 150W x 1 300W x 1 300W x 1 600W x 1 600W x 1 1200W x 1 Longitud | pulg. [mm] 8-1/8 [210] 8-1/8 [210] 12-1/16 [310] Especifi caciones comunes para todos los modelos: Altura | in [mm] 2-3/8 [60] Ancho | pulg. [mm] 7-3/16 [180] R ...

  • Kicker CX1200.1 - page 9

    9 soporte de doble ranura tornillos hexagonales panel de fondo del amplifi cador + + – – Cableado: Desconecte la batería del vehículo para evitar cortocircuitos. Luego, conecte un cable de conexión a tierra al amplifi cador . El cable de conexión a tierra debe ser corto, de 24 plg. (60 cm) o menos, y debe ir conectado a un punto sólido d ...

  • Kicker CX1200.1 - page 10

    10 GND REM +12V 12V batería fusible externo encendido a distancia (página 11) conexión a tierra conexión a tierra  18” (45cm)  24” (60cm) woofer Modelo Fusible Externo (no incluido) Cable de Alimentación y Conexión a T ierra Kit de cableado KICKER CX300.1 1 x 40A Calibre 8 PK8, ZCK84 CX600.1 1 x 80A Calibre 4 PK4, CK44, ZCK44 CX1200 ...

  • Kicker CX1200.1 - page 11

    11 FUNCIONAMIENTO Selección de Encendido Automático: El modelo CX le ofrece dos distintos modos de encendido automático; desvío a +12V y DC. • Encendido a Distancia: Instale cable calibre 18 desde el conductor de encendido a distancia de la unidad fuente hasta la terminal etiquetada REM entre las terminales de alimentación positiva y negativ ...

  • Kicker CX1200.1 - page 12

    12 RESOLUCIÓN DE PROBLEMAS Si su amplifi cador parece no estar funcionando, revise lo obvio primero: fusibles quemados, conexiones malas o incorrectas, posición incorrecta de los selectores de crossover y amplifi cación, etc. Su amplifi cador modelo CX de KICKER cuenta con los LED de protección (PRT) y de encendido (PWR) en el panel de alime ...

  • Kicker CX1200.1 - page 13

    13 ¿No hay salida de uno de los canales?  Revise el control de balance de la unidad fuente.  Revise las conexiones RCA (o de entrada de altavoz) y de salida de altavoz del canal. ¿Hay ruido sibilante de alternador asociado a las RPM del motor?  Vea si hay algún cable RCA (o de entrada de altavoz) dañado.  Revise el encaminamiento de ...

  • Kicker CX1200.1 - page 14

    14 Modell: CX300.1 CX600.1 CX1200.1 RMS-Leistung @ 14.4V , 4 Ω mono,  1% Gesamtklirrfaktor @ 14.4V , 2 Ω mono,  1% Gesamtklirrfaktor 150W x 1 300W x 1 300W x 1 600W x 1 600W x 1 1200W x 1 Länge | Zoll [mm] 8-1/8 [210] 8-1/8 [210] 12-1/16 [310] Spezifi kationen für alle Modelle: Höhe | Zoll [mm] 2-3/8 [60] Breite | Zoll [mm] 7-3/16 [180] ...

  • Kicker CX1200.1 - page 15

    15 Doppelt geschlitzte Halterung V erstärkerabdeckplatte Sechskantschrauben Anschluss: T rennen Sie den Anschluss der Fahrzeugbatterie, um einen Kurzschluss zu vermeiden. Schließen Sie dann das Massekabel an den V erstärker an. Verwenden Sie ein kurzes Erdungskabel (maximal 60 cm) und schließen Sie es an eine lack- oder korrosionsfreie Metallst ...

  • Kicker CX1200.1 - page 16

    16 GND REM +12V 12V MONO-BETRIEB Minimalimpedanz von 2 Ohm Modell Externe Sicherung (nicht inbegriffen) Massekabel KICKER V erkabelungssatz CX300.1 1 x 40 Ampere 8 GA PK8, ZCK84 CX600.1 1 x 80 Ampere 4 GA PK4, CK44, ZCK44 CX1200.1 1 x 150 Ampere 4 GA PK4, CK44, ZCK44 Batterie Ferneinschaltung (Seite 17) Masse Masse  18” (45cm)  24” (60cm) ...

  • Kicker CX1200.1 - page 17

    17 Automatische Einschaltung: Die CX-Serie umfasst zwei automatische Einschaltmodi: +12V und DC Offset. • Remote T urn-On (Ferneinschaltung): Verlegen Sie 18 GA-Kabel von der Ferneinschaltung an Ihrem Autoradio zum REM-T erminal zwischen den positiven und negativen Stromanschlüssen des Verstärkers. Das ist die bevorzugte automatische Einschaltu ...

  • Kicker CX1200.1 - page 18

    18 CXRC BASSPEGEL-FERNBEDIENUNG INST ALLA TION Stecken Sie das mitgelieferte 1/8 Zoll [3.5mm] Patchkabel in den CXRC- Remote-Regler und in die “Remote-Bass”-Steckerbuchse am V erstärker . Rückansicht Montieren Sie den CXRC-Remote-Regler mit den mitgelieferten Schrauben. PROBLEMBEHEBUNG Wenn der V erstärker nicht zu funktionieren scheint, sol ...

  • Kicker CX1200.1 - page 19

    19 Lichtmaschine erzeugt bei steigender Motordr ehzahl heulendes Geräusch?  Prüfen Sie, ob das RCA- oder Lautsprechereingangskabel defekt ist.  Prüfen Sie den V erlauf des RCA- oder Lautsprechereingangskabels.  Prüfen Sie, ob das Autoradio richtig geerdet ist.  Prüfen Sie die V erstärkungseinstellungen und reduzieren Sie diese ggf ...

  • Kicker CX1200.1 - page 20

    20 Modèle: CX300.1 CX600.1 CX1200.1 Alimentation RMS à 14,4V , 4  mono,  1% THD+N à 14,4V , 2  mono,  1% THD+N 150W x 1 300W x 1 300W x 1 600W x 1 600W x 1 1200W x 1 Longueur | en [mm] 8-1/8 [210] 8-1/8 [210] 12-1/16 [310] Spécifi cations communes à tous les modèles : Hauteur | en [mm] 2-3/8 [60] Largeur | en [mm] 7-3/16 [180] Co ...

  • Kicker CX1200.1 - page 21

    21 Câblage: Débranchez la batterie du véhicule pour éviter un court-circuit. Ensuite, raccordez le fi l de masse à l’amplifi cateur . Le fi l de masse doit être le plus court possible, de 60 cm (24 po) maximum. Raccordez-le à une partie métallique solide du châssis du véhicule, ne comportant ni peinture ni rouille. Il est recommandé ...

  • Kicker CX1200.1 - page 22

    22 FONCTIONNEMENT MONO impédance minimum de 2 ohms Modèle Fusible Externe (non inclus) Fil de Masse / Alimentation KICKER Kit de câblage CX300.1 1 x 40 Ampères Calibre 8 PK8, ZCK84 CX600.1 1 x 80 Ampères Calibre 4 PK4, CK44, ZCK44 CX1200.1 1 x 150 Ampères Calibre 4 PK4, CK44, ZCK44 GND REM +12V 12V Batterie Mise sous tension à distance (page ...

  • Kicker CX1200.1 - page 23

    23 UTILISA TION Sélection de Mise sous T ension Automatique : La série CX propose deux modes d’allumage automatique différents ; +12 V et décalage en continu. • Mise sous T ension à Distance : Faites passer un fi l de calibre 18 à partir du fi l de mise sous tension à distance sur votre appareil source jusqu’à la borne étiquetée R ...

  • Kicker CX1200.1 - page 24

    24 EN CAS DE DIFFICUL TÉ Si votre amplifi cateur ne marche pas, vérifi ez d’abord les possibilités évidentes comme les fusibles sautés, les branchements incorrects ou desserrés, le mauvais réglage des commandes de gain et du commutateur du fi ltre etc. Se présentent également des DEL d’alimentation (PWR) et de protection (PRT) sur l ...

  • Kicker CX1200.1 - page 25

    25 Piaulement prolongé de l’alternateur avec le régime du moteur ?  Vérifi ez l’état du câble RCA (ou d’entrée de haut-parleur)  Vérifi ez l’acheminement du câble RCA (ou d’entrée de haut-parleur)  Vérifi ez que l’appareil source est correctement mis à la masse  Vérifi ez les paramètres de gain et baissez-en ...

  • Kicker CX1200.1 - page 26

    26 ELECTRONICS LIMITED W ARRANTY When purchased from an Authorized KICKER Dealer , KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identifi ed as “Refurbished” or “B Goods”, the warranty is limited ...

  • Kicker CX1200.1 - page 27

    27 INTERNA TIONAL W ARRANTY Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! T urning up a system to a level that has audible distortion is more damaging to your ear ...

  • Kicker CX1200.1 - page 28

    ©2012 Stillwater Designs 2012 CX Mono Amps Rev I.indd 28 2012 CX Mono Amps Rev I.indd 28 6/22/2012 2:32:43 PM 6/22/2012 2:32:43 PM ...

Manufacturer Kicker Category Stereo Amplifier

Documents that we receive from a manufacturer of a Kicker CX1200.1 can be divided into several groups. They are, among others:
- Kicker technical drawings
- CX1200.1 manuals
- Kicker product data sheets
- information booklets
- or energy labels Kicker CX1200.1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kicker CX1200.1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kicker CX1200.1, service manual, brief instructions and user manuals Kicker CX1200.1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kicker CX1200.1.

Similar manuals

A complete manual for the device Kicker CX1200.1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kicker CX1200.1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kicker CX1200.1.

A complete Kicker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kicker CX1200.1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kicker CX1200.1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kicker CX1200.1, that we can find in the current document
3. Tips how to use the basic functions of the device Kicker CX1200.1 - which should help us in our first steps of using Kicker CX1200.1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kicker CX1200.1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kicker CX1200.1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kicker CX1200.1?

Use the form below

If you did not solve your problem by using a manual Kicker CX1200.1, ask a question using the form below. If a user had a similar problem with Kicker CX1200.1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)