English dropdown-ico

Manual Makita 2030S

28 pages 1.39 mb
Download

Go to site of 28

Summary
  • Makita 2030S - page 1

    312 mm (12-9/32") MODEL 2030s Auto feed Manual feed Auto feed Manual feed No load speed (RPMI 9,000 INSTRUCTION MANUAL Cutting width Max. cutting depth Feed rateimin Imml Imml lml 3.0 (118") for stock 0 - 150 (0'' ~ 5-29132"1 wide 1 5 (1/16"1 for stock 150 ~~ 240 15-29/32" ~ 9-7/16"] wide 1.0 13/64'] for ...

  • Makita 2030S - page 2

    For Your Own Safety Read Instruction Manual Before Operating Planer-Jointer GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GUARDS IN PLACE and in working order. 3. REMOVE ADJUSTING ...

  • Makita 2030S - page 3

    16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and namepl ...

  • Makita 2030S - page 4

    VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...

  • Makita 2030S - page 5

    FOR JOINTER 1. Maintain the proper relationships of infeed and outfeed table surfaces and cutterhead blade path. 2. Do not perform jointing operations on material shorter than 140 mm (5-1/2 inches), narrower than 19 mm (3/4 inch), or less than 12.7 mm (112 inch) thick. 3. Do not perform planing operations on material shorter than 140 mm (5-1/2 inch ...

  • Makita 2030S - page 6

    Movement and transport of planer-jointer When moving the tool, hold it as shown in the figure. When transporting it by vehicle, secure with a rope or other substantial means to prevent tipping or movement. Positioning the planer-jointer Locate the tool in a well lit and level place where you can maintain good footing and balance. Bolt it to the wor ...

  • Makita 2030S - page 7

    AUTO-PLANER FUNCTIONS: Dimensional adjustment Raise the table by turning the crank handle clockwise until the indicator plate points to the scale graduation indicating the de- sired finished dimension. One full turn of the crank handle moves the table 2 mm (3/32") up or down. The scale has inch graduations on its right side and metric graduati ...

  • Makita 2030S - page 8

    Operation Determine the depth of cut as described before. Insert the workpiece flat on the table top. When cutting a long or heavy workpiece, lift up its end slightly at the start and the end of the cut to avoid goug- ing or sniping at the extreme ends of the work p i ece. 3 Two rollers are provided on top of the tool to enable quick, effotless ret ...

  • Makita 2030S - page 9

    JOINTER FUNCTIONS: Extension support table The extension support table is convenient for cutting long workpieces. Install it on the outfeed table and semi-tighten the four hex bolts. Extend the legs and hook the arms over the screw using the hook (A). Then tighten the screws securely. Adjust the table height using the knobs so that the extension su ...

  • Makita 2030S - page 10

    Adjusting the fence angle I ClamD screw (A) 7 Hex bolts (A) The fence angle can be adjusted at any angle from 0’ to 45’. Loosen the clamp screws (A) and (B) and pull the fence out slightly. Then tighten the clamp screws (A) and (B). Loosen the hex bolts (A) and (B) and tilt the fence according to your work. Then tighten the hex bolts (A) and (B ...

  • Makita 2030S - page 11

    Beveling To cut a bevel, set the fence at the required angle and run the workpiece across the blades while keeping it firmly against the fence and tables. Carefully maintain flush, steady con- tact with the fence while making the cut. REPLACING THE PLANER BLADES Dull blades can cause a rough finish, an overload of the motor and dangerous kickback o ...

  • Makita 2030S - page 12

    AUTO-PLANE R 1. Removing the blades Loosen the hex bolt which secures the chip cover and open the chip cover. Open the safety cover over the jointer and rotate the drum by turning the knob until the drum can be locked in the position whereby the blade installa- tion bolts face upward. The magnetic holder has a different shaped claw on each side. Us ...

  • Makita 2030S - page 13

    2. Installing the blades Provide a flat wood block approx. 300 mm (1 1-13/16") long and 100 mm (3-15/16") wide. Place the blade and set plate on the wood block so that the blade locating lug of the set plate rests in the groove of the blade. Adjust the set plate so that both ends of the blade protrude approx. 1 mm (3/64") beyond the ...

  • Makita 2030S - page 14

    Install the other blade as described above. Rotate the drum slowly while pressing the lock plate to make sure there is nothing abnormal. Then close the chip cover and secure using the hex bolt. CAUTION : 0 Do not tighten the blade installation bolts without the blade locating lug of the set plate correctly resting in the groove of the blade. This m ...

  • Makita 2030S - page 15

    JOINTER 1. Removing the blades CAUTION : Always close the chip cover over the auto-planer before removing the blade. Lower the infeed table fully by turning the depth adjusting knob clockwise. Loosen the hex bolt which secures the safety cover rod and lift off the safety cover. Set the fence angle at 0' and push the fence fully toward the auto ...

  • Makita 2030S - page 16

    2. Installing the blades Provide a flat wood block approx. 150 mm (5-29/32") long and 100 mm (3-1 5/16") wide. Place the blade and set plate on the wood block so that the blade locating lug of the set plate rests in the groove of the blade. Adjust the set plate so that both ends of the blade do not protrude from the ends of the set plate. ...

  • Makita 2030S - page 17

    Lock the drum in the position whereby the blade edge faces upward. Place the triangular rule flat on the outfeed table. Turn the adjusting screws until the blade edge just contacts the triangular rule. After adjusting both adjusting screws, pull the lock pin to unlock the drum. Rotate the drum by turning the knob clockwise to make sure the blade pr ...

  • Makita 2030S - page 18

    Install the other blade as described above. Re-install the safety cover in its original position and be sure that the safety cover works properly and briskly. CAUTION : Do not tighten the blade installation bolts without the blade locating lug of the set plate correctly resting in the groove of the blade. This may cause damage to the blade and pote ...

  • Makita 2030S - page 19

    REMOVING OR INSTALLING THE JOINTER CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the jointer. The jointer can be easily removed from the auto-planer. You can carry it by yourself. 1. Removing the jointer Loosen the right and left knobs. Pull the jointer toward you as shown in the figure. The join ...

  • Makita 2030S - page 20

    Loosen the clamp screws which secure I the fence. Remove the fence. Align the line on the coupling with the pointer on the frame of the jointer. Coup1 ing s Line eoin t e r Align the two shafts of the jointer with the mating holes in the auto-planer. Push the jointer toward the auto-planer until the frame of the jointer contacts that of the auto- p ...

  • Makita 2030S - page 21

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes c Remove and check the carbon brushes re- 1 gularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes shoul ...

  • Makita 2030S - page 22

    ACCESSOR I ES ATTENTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade 0 Magnetic holder 0 Key Par ...

  • Makita 2030S - page 23

    Mar-22-’94 US 312 mm (12-9/32”) Model 2030s PLANER-JOINTER 23 ...

  • Makita 2030S - page 24

    24 ...

  • Makita 2030S - page 25

    Note: The switch and other part configurations may differ from country to country. 25 ...

  • Makita 2030S - page 26

    MODEL 2030s MACHlNE 74 1 75 1 76 1 11 1 78 1 79 1 80 1 81 16 82 2 84 1 85 1 86 1 87 1 88 1 89 1 90 1 91 2 92 1 93 1 94 1 95 2 96 1 97 1 98 1 99 1 100 1 101 1 102 1 103 2 104 1 105 2 106 1 107 1 108 1 109 1 111 1 1 110 8 'v0M $& DESCRIPTION Mar.-22-'94 US $& DESCRIPTION MA( 1 2 3 4 5 6 1 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 2 ...

  • Makita 2030S - page 27

    MODEL 20305 Mar-22-'94 US MACHINE 147 1 Hex Flange Head Bolt M6x17 148 1 Leg 149 1 Foot 150 1 Base Cover 151 1 Pan Head Screw M5x16 IWith Washer) 152 4 Spring Pin 6 36 153 1 Base 154 4 Cap 20 155 1 Drum cover 158 1 Retaining Ring S 12 157 1 SpringPin4-16 158 1 Spring Pin 4-32 159 1 Rod 12-95 160 1 Torsion Spring 14 161 2 Bedplate 162 1 Adlust ...

  • Makita 2030S - page 28

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Poiicy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...

Manufacturer Makita Category Planer

Documents that we receive from a manufacturer of a Makita 2030S can be divided into several groups. They are, among others:
- Makita technical drawings
- 2030S manuals
- Makita product data sheets
- information booklets
- or energy labels Makita 2030S
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita 2030S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita 2030S, service manual, brief instructions and user manuals Makita 2030S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita 2030S.

Similar manuals

A complete manual for the device Makita 2030S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita 2030S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita 2030S.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita 2030S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita 2030S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita 2030S, that we can find in the current document
3. Tips how to use the basic functions of the device Makita 2030S - which should help us in our first steps of using Makita 2030S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita 2030S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita 2030S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita 2030S?

Use the form below

If you did not solve your problem by using a manual Makita 2030S, ask a question using the form below. If a user had a similar problem with Makita 2030S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)