English dropdown-ico

Manual Emerson Process Management G13

50 pages 0.21 mb
Download

Go to site of 50

Summary
  • Emerson Process Management G13 - page 1

    www.Fisher.com D102754X012 Bettis r S ervice I nstructions f or Models G 01 through G 13 P neumatic A ctuators The following instruction manual is for the Bettis Actuator. This instruction manual was prepared by Bettis, a member of the Valve Automation Division of Emerson Process Management t . Please contact Bettis to ensure that the following ins ...

  • Emerson Process Management G13 - page 2

    Bettis Actuators G01 through G13 Instruction Manual Form 5653 February 2007 2 Emerson Process Management Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 www.Fisher.com The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy ...

  • Emerson Process Management G13 - page 3

    ...

  • Emerson Process Management G13 - page 4

    ENGLISH LANUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G13 PNEUM ATIC ACTUATORS PART NUMBER : 124840E REVISION: “B” DATE: 17 December 2001 ...

  • Emerson Process Management G13 - page 5

    Bettis P/N 124840E Revision “B” Page 1 of 46 CONTENTS SECTION 1.0 – INTRODUCTION PAGE 1.1 General Service Information ................................................................... 3 1.2 Definitions ............................................................................................... 4 1.3 General Safety Information ........... ...

  • Emerson Process Management G13 - page 6

    Bettis P/N 124840E Revision “B” Page 2 of 46 CONTENTS SECTION 5.0 - MODULE REMOVAL AND INSTALLATION 5.1 Spring Module Removal .......................................................................... 31 5.2 Spring Module Installation ....................................................................... 33 5.3 Pneumatic Power Module Removal . ...

  • Emerson Process Management G13 - page 7

    Bettis P/N 124840E Revision “B” Page 3 of 46 SECTION 1 - INTRODUCTION 1.1 GENERAL SERVICE INFORMATION 1.1.1 This servi ce procedure is offered as a guide to enable general maintenance to be performed on Bettis G01XXX, G2XXX, G3XXX, G4XXX, G5XXX, G7XXX, G8XXX, G10XXX, G13XXX Double Acting and Spring Return Series Single Power Module Pneumatic Ac ...

  • Emerson Process Management G13 - page 8

    Bettis P/N 124840E Revision “B” Page 4 of 46 1.2 DEFINITIONS WARNING: If not observed, user incurs a high risk of severe damage to actuator and/or fatal injury to personnel. CAUTION: If not observed, user may incur damage to actuator and/or injury to personnel. NOTE: Advisory and information comments provided to assist maintenance personnel to ...

  • Emerson Process Management G13 - page 9

    Bettis P/N 124840E Revision “B” Page 5 of 46 ACTUATOR MODEL BETTIS PART NUMBER ACTUATOR MODEL BETTIS PART NUMBER G01 None required G5/G7 117369 G2 123616 G8/G10 117368 G3/G4 117370 G13 122849 1.5.3 Commercial leak testing solution. 1.5.4 Non -hardening thread sealant. 1.6 LUBRICATION REQUIREMENTS NOTE: Lubricants, othe r than listed in step 1.6 ...

  • Emerson Process Management G13 - page 10

    Bettis P/N 124840E Revision “B” Page 6 of 46 2.1.3 The Pneumatic Power Module can be disassembled while still attached to the Drive Module or the Pneumatic Power Module can be removed from the Drive Module and disassembled separate to the actuator (refer to Section 5 - Module Removal And Installation). 2.1.4 To ensure correct re -assembly; that ...

  • Emerson Process Management G13 - page 11

    Bettis P/N 124840E Revision “B” Page 7 of 46 2.2.4.2.2 Refer to assembly drawing page 2 of 2 Detail "E". If not already removed unscrew and remove two socket cap screws (3 -130), with lockwasher (3 -140), from outer end cap (3 -80). 2.2.4.2.3 Remove socket cap screw (3 -130) with lockwasher (3 -140) from keeper (3 -360). 2.2.4.2.4 Rem ...

  • Emerson Process Management G13 - page 12

    Bettis P/N 124840E Revision “B” Page 8 of 46 2.2.8.1.2 Remove o -ring seals (4 -80) from the inboard end of tie bars (3 -20). 2.2.8.2.3 Remove tie bars (3 -20) by pulling the tie ba rs out and through piston (3 -30). NOTE: G4 models have flats on outboard end of tie bars (3 -20) for wrench placement. NOTE: G5 through G13 models have a female sq ...

  • Emerson Process Management G13 - page 13

    Bettis P/N 124840E Revision “B” Page 9 of 46 2.2.14 Unscrew and remove piston rod (3 -40) fro m drive module. 2.3 DRIVE MODULE DISASSEMBLY NOTE: Review Section 2 steps 2.1.1 through 2.1.5 General Disassembly before proceeding with Drive Module Disassembly. 2.3.1 If not already removed remove piston rod (3 -40) from drive module. NOTE: If the a ...

  • Emerson Process Management G13 - page 14

    Bettis P/N 124840E Revision “B” Page 10 of 46 2.3.12 Using hex cap screws (1 -110), install into holes vacated by hex cap screws (1 -120). Use these hex cap screws to jack the housing cover up for removal. Alternately rotate the hex cap screws clockwise until housing cover (1 -20) is clear of housing (1 -10). NOTE: G01, G2, G3 and G4 model hous ...

  • Emerson Process Management G13 - page 15

    Bettis P/N 124840E Revision “B” Page 11 of 46 NOTE: One spherical washer (1 -40) will be removed from guide block (1 -30) when extension rod assembly is removed. On spring return actuators also one spherical washer (9 -40) will be removed from guide block (1 -30). 2.3.25 Remove the remaining spherical washer (1 -40) from guide block (1 -30). On ...

  • Emerson Process Management G13 - page 16

    Bettis P/N 124840E Revision “B” Page 12 of 46 2.6 M3 JACKSCREW DISSASSEMBLY NOTE: The jackscrew bearing retainer (7 -110) / (5 -110), needle bearing thrust washer assembly (7 -100) / (5 -100) or retainer ring (7 -90) / (5 -90) does not require disassembly from the jackscrew assembly (7 -40) / (5-50) except for the ne ed to replace worn parts. F ...

  • Emerson Process Management G13 - page 17

    Bettis P/N 124840E Revision “B” Page 13 of 46 2.6.4.2 Unscrew and remove hex flat nut (7 -50) from M3 jackscrew assembly (7 -40). 2.6.4.3 Unscrew and remove two socket cap screws (7 -120) from M3 adapter (7 -40 ). 2.6.4.4 Remove M3 jackscrew (7 -40) from M3-SR adapter plate (7 -10). 2.6.5 M3 THRUST BEARING DISASEMBLY FROM M3 JACKSCRE W ASSEMBLY ...

  • Emerson Process Management G13 - page 18

    Bettis P/N 124840E Revision “B” Page 14 of 46 NOTE: The parts and seals used in the actuator will be assembled using lubricant as identified in section 1 step 1.6.1. 3.1.5 For Spri ng Module Installation refer to Section 5 step 5.2. 3.2 DRIVE MODULE REASSEMBLY NOTE: Review section 3.1 General Reassembly before proceeding with Drive Module Reass ...

  • Emerson Process Management G13 - page 19

    Bettis P/N 124840E Revision “B” Page 15 of 46 3.2.10 Install second spherical washer (9 -40) over threaded end of extension rod assembly (9 -50). NOTE: The spherical side of the washer will go on the extension rod assembly facing the head of the extension rod assembly. 3.2.11 Install extension rod assembly (9 -50) into guide block (1 -30) and u ...

  • Emerson Process Management G13 - page 20

    Bettis P/N 124840E Revision “B” Page 16 of 46 3.2.22 Align hole in guide block (1 -30) with the matching holes in the two yoke/guide block bushings (2 -30) and the slots in the arms of yoke (1 -70). NOTE: The yoke pin can be held in place by installing a screw into the .3 75 -16UNC tapped hole in the upper end of yoke pin (1 -80). 3.2.23 Instal ...

  • Emerson Process Management G13 - page 21

    Bettis P/N 124840E Revision “B” Page 17 of 46 NOTE: Comple te step 3.2.34 on G5, through G13 model actuators. For G01 through G4 model actuators skip step 3.2.34 and proceed to step 3.2.35. 3.2.34 On G5 through G13 models 3.2.34.1 Place lockwashers (1 -115) onto hex cap screws (1 -120). NOTE: Hex cap screw ( 1 -120) are only used as "hole& ...

  • Emerson Process Management G13 - page 22

    Bettis P/N 124840E Revision “B” Page 18 of 46 3.2.48 Adjust both stop screws (1 -180 ) back to settings recorded earlier in Section 2 at step 2.3.2. 3.2.49 Tighten both stop screw nuts (1 -190) securely. 3.3 PNEUMATIC POWER MODULE REASSEMBLY NOTES: 1. For early model G2 and G3 actuators with double nuts on the power module use section 3.4 for r ...

  • Emerson Process Management G13 - page 23

    Bettis P/N 124840E Revision “B” Page 19 of 46 3.3.8 Place lockwashers (3 -110) onto hex cap screws (3 -100). 3.3.9 Install and tighten hex cap screws (3 -100), with lockwashers, through housing (1 -10) and into inner end cap (3 -10). 3.3.11 Refer to assembly drawing page 2 of 2 Detail "D". Install o ne o -ring seal (4 -70) into the se ...

  • Emerson Process Management G13 - page 24

    Bettis P/N 124840E Revision “B” Page 20 of 46 3.3.22 Install lubricated cylinder (3 -70) over piston (3 -30) and onto inner end cap (3 -1 0). When installing the cylinder over the piston seal tilt cylinder 15 ° to 30 ° degrees to piston rod. 3.3.23 OUTER END CAP (3 -80) INSTALLATION AS FOLLO WS: G01-M3 use step 3.3.23.1, G2 -M3 and G3 -M3 use ...

  • Emerson Process Management G13 - page 25

    Bettis P/N 124840E Revision “B” Page 21 of 46 3.3.23.2.2 Install the jackscrew (3 -290) through the outboa rd side of the outer end cap (3 -80). 3.3.23.2.3 Apply a light coating of lubricant to threads of jackscrew (3 -290). 3.3.23.2.4 Screw jackscrew adapter (3 -280) onto jackscrew (3 -290). NOTE: The small round end of the M3 adapter will ins ...

  • Emerson Process Management G13 - page 26

    Bettis P/N 124840E Revision “B” Page 22 of 46 3.3.25 Install lockwashers (3 -140) onto socket cap screws (3 -130) . 3.3.26 Install and tighten socket cap screws (3 -130), with lockwashers (3 -140), into outer end cap (3 -80). NOTE: If the outer end cap (3 -80) has an ES stop screw completed steps 3.3.27 through 3.3.29. 3.3.27 If not already rem ...

  • Emerson Process Management G13 - page 27

    Bettis P/N 124840E Revision “B” Page 23 of 46 3.4.4 Install piston rod (3 -40) through inner end cap (3 -10). NOTE: The piston rod end with retainer grooves to be on the outboard side of inner end cap (3 -10). 3.4.5 Apply lubricant to two sets of rod T -seal components (4 -50) . NOTE: The T -seal is composed of one rubber seal and two split ski ...

  • Emerson Process Management G13 - page 28

    Bettis P/N 124840E Revision “B” Page 24 of 46 CAUTION: If needed, when installing the cylinder, hammer on the end of the cylinder only with a non metallic object. 3.4.17 Install lubricated cylinder (3 -70) over piston (3 -30) and onto inner end cap (3 -10). When installing the cylinder over the piston seal tilt cylinder 15 ° to 30 ° degrees t ...

  • Emerson Process Management G13 - page 29

    Bettis P/N 124840E Revision “B” Page 25 of 46 3.6 M3 JACKSCREW ASSEMBLY NOTE: 1. This section is to be completed when the M3 jackscrew has been disassembled from the blind end cap or from the SR-M3 adapter plate (7 -10). NOTE: 2. If the thru st bearing assembly has been disassembled from the M3 jackscrew stud then pre assemble the thrust bearin ...

  • Emerson Process Management G13 - page 30

    Bettis P/N 124840E Revision “B” Page 26 of 46 3.6.2.6 Install two socket cap screws (5-120) through jackscrew adapter (5-45) and tighten into blind end cap (5-10). 3.6.2.7 Lightly lubricate o -ring seal (6 -30) and install onto the outboard end of the M3 jackscrew assembly. Push the o -rin g (6 -30) down the M3 until it contacts the M3 adapter ...

  • Emerson Process Management G13 - page 31

    Bettis P/N 124840E Revision “B” Page 27 of 46 3.6.5.3.3 Apply lubricant to the remaining thrust washer an d install onto bearing retainer (5 -110) / (7 -110) and up against the needle bearing installed in step 3.6.1.3.2. 3.6.5.4 Install the pre -assembled needle bearing thrust washer assembly (5 -100) / (7 -100) into the open hole located on th ...

  • Emerson Process Management G13 - page 32

    Bettis P/N 124840E Revision “B” Page 28 of 46 3.8.3 Install ES stop screw (5-50) through ES blind end cap (5-10). 3.9 ACTUATOR TESTING 3.9.1 Leakage Test - All areas where leakage to atmosphere may occur are to b e checked, using a commercial leak testing solution. CAUTION: Pressure applied to the actuator is not to exceed the maximum operating ...

  • Emerson Process Management G13 - page 33

    Bettis P/N 124840E Revision “B” Page 29 of 46 4.1.2 Remove Pneumatic Power Module per Section 5.3. 4.1.3 Re -install the Spring Module onto the opposite en d of housing (1 -10), as it was previously located per Section 5.2. 4.1.4 Re -install the Pneumatic Power Module onto the opposite end of housing (1 -10) as it was previously located per Sec ...

  • Emerson Process Management G13 - page 34

    Bettis P/N 124840E Revision “B” Page 30 of 46 4.5.2 If new M3 outer end cap (3 -80) is not pre assembled with the M3 then assembly M3 to the outer end cap (3 -80) per Section 3.3 steps 3.3.23.1 or 3.3.23.2. 4.5.3 Install the assembled M3 outer end cap (3 -80) per Section 3.3 steps 3.3.23.2.11 or 3.3.23.3.11 and 3.3.24 through 3.3.26. 4.5.4 To i ...

  • Emerson Process Management G13 - page 35

    Bettis P/N 124840E Revision “B” Page 31 of 46 4.9.2.2 Install o -ring seal (6–30) onto outboard end of ES (7 -40) and up against outboard side of adapter plate (7 -10). 4.9.2.3 Install stop screw nut (7 -50) onto outboard end of ES (7 -40). 4.9.3 Install the assembled ES adapter plate (7 -10) onto the spring cartridge out end per Section 5.2 ...

  • Emerson Process Management G13 - page 36

    Bettis P/N 124840E Revision “B” Page 32 of 46 5.1.3 Remove the cover plate (7 -10) from spring cartridge assembly (5 -10). 5.1.4 Apply pneumatic pressure t o inner end cap (2 -40) port “A” to compress the spring enough to move the yoke off the stop screw on the spring module side of the drive module. 5.1.5 Loosen the stop screw nut (1 -190) ...

  • Emerson Process Management G13 - page 37

    Bettis P/N 124840E Revision “B” Page 33 of 46 5.2 SPRING MODULE INSTALLATION CAUTION: Due to the weight a nd size of Spring Module, heavy duty support equipment will be required when installing spring cartridge module to the actuator housing. For the approximate weight of the spring cartridge refer to Section 6. WARNING ACTUATOR MUST BE IN THE ...

  • Emerson Process Management G13 - page 38

    Bettis P/N 124840E Revision “B” Page 34 of 46 WARNING: After initial thread engagement the tension rod must be rotated clockwise the minimum number of turns listed in the following table. ACTUATOR MODEL TORQUE UNITS G01 G2 G3 G4 G5 G7 G8 G10 G13 MINIMUM NO TURNS N/A 6 10 10 10 13 14 20 25 31 WARNING: When screwing tension rod into extension rod ...

  • Emerson Process Management G13 - page 39

    Bettis P/N 124840E Revision “B” Page 35 of 46 HEX CAP SCREWS (7 -20) TORQUE TABLE TORQUE ±5 % Percent TORQUE ±5 % Percent HOUSING MODEL (FT-lb.) N-m HOUSING MODEL (FT-lb.) N-m G01 30 41 G7 135 183 G2 30 41 G8 240 325 G3 30 41 G10 285 386 G4 65 88 G13 340 461 G5 65 88 5.2.15 On M3, M3H W and ES models i nstall Monel wire (6 -130) through each ...

  • Emerson Process Management G13 - page 40

    Bettis P/N 124840E Revision “B” Page 36 of 46 5.2.15.5 Attach caution tag and twist tie the wires from the last screw head to the twisted wires of the first screw head. See following for illustration. 5.2.16 If removed install stop screw nuts (1 -190) onto stop screws (1 -180). 5.2.17 If removed install o -ring (2 -90) onto stop screws (1 -180) ...

  • Emerson Process Management G13 - page 41

    Bettis P/N 124840E Revision “B” Page 37 of 46 5.3 PNEUMATIC POWER MODULE REMOVAL CAUTION: Due to the weight and size of power module, heavy duty support equipment will be required when removing power module from the actuator housing. Refer to section 6 for Pneumatic Power Module weights. 5.3.1 Standard Outer end cap with pipe plug use step 5.3. ...

  • Emerson Process Management G13 - page 42

    Bettis P/N 124840E Revision “B” Page 38 of 46 5.4.2 Using lifting equipment move the power module up to the drive module and align piston rod (3 -40) as fo llows: 5.4.2.1 G2 through G13 models align piston rod (3 -40) with power module extension rod assembly (1-50). 5.4.2.2 G01 models align piston rod (3 -40) with the drive module guide block ( ...

  • Emerson Process Management G13 - page 43

    Bettis P/N 124840E Revision “B” Page 39 of 46 5.3.1.4.3 Remove M3 jackscrew (3 -290) with M3 adapter (3 -360) from outer end cap (3 -80). 5.5 G2 THRU G13 POWR SWIVL REMOVAL CAUTION: While step 5.5.1 is in progress be sure to maintain guide bar retention wh en moving the guide block. 5.5.1 Push the guide block to the side of housing (1 -10) that ...

  • Emerson Process Management G13 - page 44

    Bettis P/N 124840E Revision “B” Page 40 of 46 5.6.5 Install extension rod assembly (1 -50) into right of guide block (1 -30) and up against the first spherical washer (1 -40). 5.6.6 Install extension retainer nut assembly (1 -60) over extension rod assembly (1 -50) and screw into guide block (1 -30). 5.6.7 Tighten extension retainer nut assembl ...

  • Emerson Process Management G13 - page 45

    Bettis P/N 124840E Revision “B” Page 41 of 46 6.1 CONTINUED - MODULE WEIGHTS BY ITEM NUMBER AND ACTUATOR HOUSING SIZE ITEM NO. G01 WT. G2 WT. G3 WT. G4 WT G5 WT G7 WT. G8 WT. G10 WT. G13 WT. MODULE DESCRIPTION 3 Lbs. N/A N/A N/A N/A N/A N/A 1975 2205 - 40” Dia. Power Kg N/A N/A N/A N/A N/A N/A 896 1000 - Module 3 Lbs. N/A N/A N/A N/A N/A N/A ...

  • Emerson Process Management G13 - page 46

    Bettis P/N 124840E Revision “B” Page 42 of 46 6.2 G01 TOOL STYLE AND WRENCH SIZE ITEM NO. WRENCH SIZE ITEM QTY LOCATION OR DESCRIPTION RECOMMENDED TOOL STYLE 1 -110 9/16” 4 Hex Cap Screws Socket 1 -160 ½” 4 Hex Cap Screws Socket 1 -180 3/8” Sq. 2 Stop Screws Open End or Adjustable 1 -190 1 -15/16” 2 Hex Jam Nuts Open End or Adjustable ...

  • Emerson Process Management G13 - page 47

    Bettis P/N 124840E Revision “B” Page 43 of 46 6.4 G3 TOOL STYLE AND WRENCH SIZE ITEM NO. WRENCH SIZE ITEM QTY LOCATION OR DESCRIPTION RECOMMENDED TOOL STYLE 1 -110 9/16” 8 Hex Cap Screws Socket 1 -160 9/16” 4 Hex Cap Screws Socket 1 -180 1/2” Sq. 2 Stop Screws Open End or Adjustable 1 -190 1 -5/16” 2 Hex Jam Nuts Open End or Adjustable ...

  • Emerson Process Management G13 - page 48

    Bettis P/N 124840E Revision “B” Page 44 of 46 6.6 G5 TOOL STYLE AND WRENCH SIZE ITEM NO. WRENCH SIZE ITEM QTY LOCATION OR DESCRIPTION RECOMMENDED TOOL STYLE 1 -110 3/4” 8 Hex Cap Screws Socket 1 -120 3/4” 4 Hex Cap Screws Socket 1 -160 9/16” 6 Hex Cap Screws Socket 1 -180 7/8” Sq. 2 Stop Screws Open End or Adjustable 1 -190 2 -3/8” 2 ...

  • Emerson Process Management G13 - page 49

    Bettis P/N 124840E Revision “B” Page 45 of 46 6.8 G8 TOOL STYLE AND WRENCH SIZE ITEM NO. WRENCH SIZE ITEM QTY LOCATION OR DESCRIPTION RECOMMENDED TOOL STYLE 1 -110 3/4” 12 Hex Cap Screws Socket 1 -120 3/4” 4 Hex Cap Screws Socket 1 -160 9/16” 8 Hex Cap Screws Socket 1 -180 1 -1/4” 2 Stop Screws Open End or Adjustable 3 -20 3/4” Sq. 2 ...

  • Emerson Process Management G13 - page 50

    Bettis P/N 124840E Revision “B” Page 46 of 46 6.10 G13 TOOL STYLE AND WRENCH SIZE ITEM NO. WRENCH SIZE ITEM QTY LOCATION OR DESCRIPTION RECOMMENDED TOOL STYLE 1 -110 1 -1/8” 20 Hex Cap Screws Socket 1 -120 1 -1/8” 4 Hex Cap Screws Socket 1 -160 9/16” 12 Hex Cap Screws Socket 1 -180 2” Sq. 2 Stop Screws Open End or Adjustable 3 -20 3/4? ...

Manufacturer Emerson Process Management Category Automobile Parts

Documents that we receive from a manufacturer of a Emerson Process Management G13 can be divided into several groups. They are, among others:
- Emerson Process Management technical drawings
- G13 manuals
- Emerson Process Management product data sheets
- information booklets
- or energy labels Emerson Process Management G13
All of them are important, but the most important information from the point of view of use of the device are in the user manual Emerson Process Management G13.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Emerson Process Management G13, service manual, brief instructions and user manuals Emerson Process Management G13. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Emerson Process Management G13.

Similar manuals

A complete manual for the device Emerson Process Management G13, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Emerson Process Management G13 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Emerson Process Management G13.

A complete Emerson Process Management manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Emerson Process Management G13 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Emerson Process Management G13, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Emerson Process Management G13, that we can find in the current document
3. Tips how to use the basic functions of the device Emerson Process Management G13 - which should help us in our first steps of using Emerson Process Management G13
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Emerson Process Management G13
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Emerson Process Management G13 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Emerson Process Management G13?

Use the form below

If you did not solve your problem by using a manual Emerson Process Management G13, ask a question using the form below. If a user had a similar problem with Emerson Process Management G13 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)