English dropdown-ico

Manual Snapper 1695169

14 pages 0.82 mb
Download

Go to site of 14

Summary
  • Snapper 1695169 - page 1

    A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 1695169 Clean Sweep Triple Catcher 1733866 Rev. 04 Rev. Date 12/2006 TP 100-4405-04-AT-SMAN Clean Sweep T riple Catc her ...

  • Snapper 1695169 - page 2

    THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT) ...

  • Snapper 1695169 - page 3

    1 Normal Remov al & Installation Collector Installation ......................................10 Collector Remov al .........................................11 NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. Safety Rules & Inf ormation General W arnings ........................... ...

  • Snapper 1695169 - page 4

    2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u ...

  • Snapper 1695169 - page 5

    Bef ore Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...

  • Snapper 1695169 - page 6

    Initial Installation 4 Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). W ARNING Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Figure 3. Hitch Installa ...

  • Snapper 1695169 - page 7

    5 T ube Component Assembly Baffle Installation 1. Determine which baffle to use. See Figure 4 Chart. 2. Lift side discharge chute (H, Figure 4). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4. Tighten carriage bolts (A) and nuts (E) on baffle (F). 5. Tighten carriage bolt (B) and nut (E) on baffle (F). 6. Positio ...

  • Snapper 1695169 - page 8

    6 Component Installation Figure 6. Lower Chute to Boot Installation A. Pin, Latch B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Strap, Rubber G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, Thin, 5/16-18 x 1 D B C F A G G H I J E ...

  • Snapper 1695169 - page 9

    Install Upright Support & Bag Support Bracket 7 Figure 8. Install Upright Support A. Hitch B. Upright Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16 A INSTALL UPRIGHT SUPPORT TO HITCH 1. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and lock- nuts (D) as shown. B INSTALL BAG AND COVER SUPP ...

  • Snapper 1695169 - page 10

    Cover and Bag Installation 8 Figure 10. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots D INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 10) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown. INSTALL COLLE ...

  • Snapper 1695169 - page 11

    9 T ube Installation C D E A B Figure 12. Install Lower Tube A. Lower Chute Rod B. Mounting Plate C. Rubber Strap D. Discharge Deflector E. Locknut LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 12). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole clos- est to knob in str ...

  • Snapper 1695169 - page 12

    Normal Removal & Installation 10 A. Hitch Support Assembly J. Deflector B. Cover K. Nut & Capscrew C. Pin L. Mounting plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R. Ridge Cutout E Q D B Normal Remo val & Installation Collecto ...

  • Snapper 1695169 - page 13

    Normal Removal 11 Collector Remov al 1. Unhook strap (P, Figure 15) from pin (O). Slide mid- dle tube (H) into upper tube (G) and remove middle tube (H). Remove upper tube (G) from cover (B). 2. Lift up cover (B) remove and empty bags (E). 3. Unhook strap (I) from locknut and capscrew (K). Remove lower chute (N) from mounting plate (L). See that th ...

  • Snapper 1695169 - page 14

    Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Simplicity Mfg. ...

Manufacturer Snapper Category Lawn Mower Accessory

Documents that we receive from a manufacturer of a Snapper 1695169 can be divided into several groups. They are, among others:
- Snapper technical drawings
- 1695169 manuals
- Snapper product data sheets
- information booklets
- or energy labels Snapper 1695169
All of them are important, but the most important information from the point of view of use of the device are in the user manual Snapper 1695169.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Snapper 1695169, service manual, brief instructions and user manuals Snapper 1695169. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Snapper 1695169.

Similar manuals

A complete manual for the device Snapper 1695169, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Snapper 1695169 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Snapper 1695169.

A complete Snapper manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Snapper 1695169 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Snapper 1695169, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Snapper 1695169, that we can find in the current document
3. Tips how to use the basic functions of the device Snapper 1695169 - which should help us in our first steps of using Snapper 1695169
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Snapper 1695169
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Snapper 1695169 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Snapper 1695169?

Use the form below

If you did not solve your problem by using a manual Snapper 1695169, ask a question using the form below. If a user had a similar problem with Snapper 1695169 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)