English dropdown-ico

Manual American Standard MONOBLOCK BIDET 2064.011

6 pages 2.97 mb
Download

Go to site of 6

Summary
  • American Standard MONOBLOCK BIDET 2064.011 - page 1

    M968851 Rev .1.3 Cer tified to comply with ANSI A112.18.1 Installation Instructions MONOBLOCK BIDET with Speed Connect™ Drain Adjustable W rench Screwdriver Channel Locks Recommended tools T ubing Cutter 1 INST ALL FAUCET T urn off hot and cold water supplies before beginning. CAUTION 2064.011 1 SERIN ™ 1 2 5 6 4 4 GROOVE (FAUCET BASE) MOUNTIN ...

  • American Standard MONOBLOCK BIDET 2064.011 - page 2

    M968851 Rev .1.3 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 3 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B ...

  • American Standard MONOBLOCK BIDET 2064.011 - page 3

    M968851 Rev .1.3 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. CHECK OPERATION OF POP-UP 8 MAKE WA TER SUPPL Y AND WASTE CONNECTIONS 9 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) a ...

  • American Standard MONOBLOCK BIDET 2064.011 - page 4

    1 2 4 5 6 2.5mm HEX KEY REMOVE INSTALL 3 7 8 M968851 Rev .1.3 10 TEST INST ALLED FITTING With HANDLE (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Remove AERA TOR (3) . Operate HANDLE (1) to flush water lines thoroughly . Replace AERA TOR (3) . CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill Bidet ...

  • American Standard MONOBLOCK BIDET 2064.011 - page 5

    M968851 Rev .1.3 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriv ...

  • American Standard MONOBLOCK BIDET 2064.011 - page 6

    M968851 Rev .1.3 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard log ...

Manufacturer American Standard Category Plumbing Product

Documents that we receive from a manufacturer of a American Standard MONOBLOCK BIDET 2064.011 can be divided into several groups. They are, among others:
- American Standard technical drawings
- MONOBLOCK BIDET 2064.011 manuals
- American Standard product data sheets
- information booklets
- or energy labels American Standard MONOBLOCK BIDET 2064.011
All of them are important, but the most important information from the point of view of use of the device are in the user manual American Standard MONOBLOCK BIDET 2064.011.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals American Standard MONOBLOCK BIDET 2064.011, service manual, brief instructions and user manuals American Standard MONOBLOCK BIDET 2064.011. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product American Standard MONOBLOCK BIDET 2064.011.

Similar manuals

A complete manual for the device American Standard MONOBLOCK BIDET 2064.011, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use American Standard MONOBLOCK BIDET 2064.011 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of American Standard MONOBLOCK BIDET 2064.011.

A complete American Standard manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual American Standard MONOBLOCK BIDET 2064.011 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the American Standard MONOBLOCK BIDET 2064.011, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the American Standard MONOBLOCK BIDET 2064.011, that we can find in the current document
3. Tips how to use the basic functions of the device American Standard MONOBLOCK BIDET 2064.011 - which should help us in our first steps of using American Standard MONOBLOCK BIDET 2064.011
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with American Standard MONOBLOCK BIDET 2064.011
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of American Standard MONOBLOCK BIDET 2064.011 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning American Standard MONOBLOCK BIDET 2064.011?

Use the form below

If you did not solve your problem by using a manual American Standard MONOBLOCK BIDET 2064.011, ask a question using the form below. If a user had a similar problem with American Standard MONOBLOCK BIDET 2064.011 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)