English dropdown-ico

Manual Vax VO27

14 pages 2.6 mb
Download

Go to site of 14

Summary
  • Vax VO27 - page 1

    2 3 c f a d 1 2 3 Putting your cleaner together Remove your Rapide XL from the carton with caution. The handle is connected to the body by a cord. Note : Do not tug or pull on the cord. Line up the handle to the upper body of the machine and slide into place. Secure from the back with the two smaller screws. Phillips screwdriver required P arts che ...

  • Vax VO27 - page 2

    4 5 4 5 6 Putting your cleaner together Feed the cord through the slots on the back of the handle and push into place. P lace a nut into the recess in the back of the upper handle. While holding the nut in place insert one of the large screws through the front of the upper handle and tighten. Repeat the process with the second screw . R emove the b ...

  • Vax VO27 - page 3

    6 7 2 3 4 T ool storage S lide the tool caddy downwards until it is secured in place. Note : The tool caddy can be removed for storage on a wall. C onnect upholstery attachment to end of hose by pressing until it clicks into place. P ush upholstery attachment into the left hose clip, wrap the hose around the tool caddy starting on the back groove o ...

  • Vax VO27 - page 4

    8 5 6 Pre-treating your carpets with the pre-treatment wand and solution (model V -027PT only) R emove solution tank cap. C AUTION : Do not overfill. Y ou should leave 1-2 cm of air space. Fill the tank with pre-treatment solution. R eplace the solution tank cap. Return the solution tank to the cleaner making sure the solution tube lines up with th ...

  • Vax VO27 - page 5

    10 10 Pre-treating your carpets with the pre-treatment wand and solution (model V -027PT only) Using the wand and the trigger , apply pre-treatment solution to carpets. T urning the spray nozzle clockwise or anti-clockwise will alter the spray pattern. T o pre-treat carpets be sure that the brush switch is OFF and that the power and soap switches a ...

  • Vax VO27 - page 6

    12 13 4 5 6 How to operate your cleaner R emove solution tank cap. C AUTION : Do not overfill. Y ou should leave 1-2 cm of air space. Fill the tank with V AX AAA Carpet Cleaner . The cleaner can be stored with solution in the solution tank. It does not have to be removed after each use. However the solution tanks should be rinsed out periodically . ...

  • Vax VO27 - page 7

    14 15 1 2 3 How to operate your cleaner P lug the cord into an electrical socket. Step on the handle release pedal to put the cleaner into a cleaning position. T urn main power switch, brush switch and soap switch all to the ON position. Note : See page 10 for details on the various switch functions. 4 How to operate your cleaner T o spray cleaning ...

  • Vax VO27 - page 8

    1 2 3 H ose attachments P ut the cleaner in its upright position. T urn the brush switch and power switch to the off position. R emove the hose from its stored position on the back of the cleaner . Lift the hose attachment cover located on the top of the dirty water tank. I nsert the end of the hose into the tool opening and twist clockwise until i ...

  • Vax VO27 - page 9

    7 8 9 H ose attachments W hile depressing the blue solution spray trigger , pull the attachment in a downward motion. Release the trigger and push the attachment forward in the same path to remove dirty water and solution from upholstery . For heavily soiled areas, repeat if necessary . T o rinse, remember to turn the soap switch to the OFF positio ...

  • Vax VO27 - page 10

    1 2 3 E mptying the dirty water tank D epress the dirty water tank latch and simultaneously pull the dirty water tank nozzle tab up and away from the cleaner . R emove the dirty water tank by lifting the dirty water tank handle and pulling the tank out of the base. Note : The nozzle does not need to be completely removed to empty the dirty water ta ...

  • Vax VO27 - page 11

    7 8 E mptying the dirty water tank R eturn dirty water tank to the base of the cleaner by tipping the nozzle down into the basin and dropping it into place. L ift the front of the cleaner base off the carpeting with one hand. Line up the black tabs with the grooves of the front nozzle. Lift the front nozzle upwards towards the cleaner and press und ...

  • Vax VO27 - page 12

    4 1 B elt or brush removal and replacement 1 . Loop the belt around the rear shaft. 2. Loop the top of the belt above the small pulley and the bottom of the belt around the lower small pulley . 3. Feed the entire belt over the first large pulley . 4. Loop the belt around the front large pulley and rotate the front brushbar forward until the belt is ...

  • Vax VO27 - page 13

    T roubleshooting Problem Cleaner won’t run V acuum won’t pick up/loss of suction W ater escaping from the V acuum Cleaner attachments won’t spray Cleaner won’t dispense solution No soap dispensing Will not dispense water P ossible Cause • Power cord not firmly pushed into a mains socket. • Blown fuse or tripped circuit breaker . • Noz ...

  • Vax VO27 - page 14

    UK SERVICE & HELP - VA X CARE 0870 6061248 Mon-F ri. 9.00am to 5.00pm. An answer phone is a vailable out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate. Please make a note of the serial number and model number of your V AX before calling. There are over 400 appr ...

Manufacturer Vax Category Carpet Cleaner

Documents that we receive from a manufacturer of a Vax VO27 can be divided into several groups. They are, among others:
- Vax technical drawings
- VO27 manuals
- Vax product data sheets
- information booklets
- or energy labels Vax VO27
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vax VO27.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vax VO27, service manual, brief instructions and user manuals Vax VO27. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vax VO27.

Similar manuals

A complete manual for the device Vax VO27, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vax VO27 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vax VO27.

A complete Vax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vax VO27 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vax VO27, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vax VO27, that we can find in the current document
3. Tips how to use the basic functions of the device Vax VO27 - which should help us in our first steps of using Vax VO27
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vax VO27
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vax VO27 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vax VO27?

Use the form below

If you did not solve your problem by using a manual Vax VO27, ask a question using the form below. If a user had a similar problem with Vax VO27 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)