English dropdown-ico

Manual Hobart 3613 & 3713

12 pages 1.24 mb
Download

Go to site of 12

Summary
  • Hobart 3613 & 3713 - page 1

    N S T R U C T I O N S I MODEL 3613 & 3713 SLICERS MODELS 3613 Manual Slicer ML-136143 3713 Automatic Slicer ML-136144 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35218 (Oct. 2007) ...

  • Hobart 3613 & 3713 - page 2

    – 2 – © HOBART CORPORATION 2007 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking . . . . . . . . ...

  • Hobart 3613 & 3713 - page 3

    – 3 – Installation, Operation, and Care of MODEL 3613 & 3713 SLICERS SA VE THESE INSTRUCTIONS GENERAL The model 3613 and 3713 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service. The slicer features the Hobart CleanCut TM 13" diameter contoured stainless steel knife. The slicer is furnishe ...

  • Hobart 3613 & 3713 - page 4

    – 4 – PRODUCT TRAY The P RODUCT T RAY (Fig. 1) must be installed on the slicer. To install the P RODUCT T RAY on the slicer, lower the bottom of the S UPPORT A RM onto the C ARRIAGE H INGE P INS (Fig. 3). Tilt the P RODUCT T RAY toward the G AUGE P LATE . Press the K NOB on the S UPPORT A RM and rotate it in either direction until the K NOB is ...

  • Hobart 3613 & 3713 - page 5

    – 5 – SHARPENER ROD & PIN SHARPENER MOUNT SLOT Fig. 4 ELECTRICAL This machine is provided with a three-prong grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician . CLEAN BEFORE USING The 3613 or 3713 slicer must be thoroughly cleaned ...

  • Hobart 3613 & 3713 - page 6

    – 6 – Fig. 9 Fig. 8 Fig. 7 P ARK PIN IN MEA T GRIP SLOT PRODUCT TRA Y MEA T GRIP SLIDE ROD MEA T GRIP ARM TOP KNIFE COVER LA TCH KNOB PRODUCT TRA Y MEA T GRIP INDEX KNOB PRODUCT TRA Y HANDLE MEA T GRIP SLOT GAUGE PLA TE MEA T GRIP SLIDE ROD P ARK PIN CARRIAGE SLOT CONTROLS SIDE P ANEL OPERA TION Rotating knife. Use meat grip. Unplug machine pow ...

  • Hobart 3613 & 3713 - page 7

    – 7 – SLICING — MODEL 3713 • Close the G AUGE P LATE by turning the I NDEX K NOB fully clockwise (Fig. 7). • Pull the P RODUCT T RAY (Fig. 7) all the way toward you until it reaches its stop (this is the home position). • Raise the M EAT G RIP to the top of the P RODUCT T RAY , and rest the P ARK P IN on the M EAT G RIP S LOT . • Plac ...

  • Hobart 3613 & 3713 - page 8

    – 8 – CLEANING This machine must be thoroughly cleaned and sanitized at least as often as required by local regulation or after being idle for an extended period of time. The slicer knife is very sharp. Exercise extreme caution when working near the knife. Unplug the machine power cord and turn the index knob fully clockwise to close the gauge ...

  • Hobart 3613 & 3713 - page 9

    – 9 – Clean completely around the R ING G UARD by working a moistened, folded paper towel between the R ING G UARD and the K NIFE (Fig. 15). Wash, rinse and sanitize both sides of the K NIFE by wiping outward from the center. Never clean any part of the slicer with steel pads. Carefully reassemble the plastic R ING G UARD C OVER by putting it i ...

  • Hobart 3613 & 3713 - page 10

    – 10 – Using the Knife Removal Tool Accessory Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before cleaning the slicer. To Remove the Knife . . . • Remove the T OP K NIFE C OVER and the plastic R ING G UARD C OVER (Figs. 13, 14). Remove the plastic cover from the K NIFE N UT . Orient the Knife ...

  • Hobart 3613 & 3713 - page 11

    – 11 – To Reinstall the Knife . . . • Orient the R IDGE on the K NIFE H UB so it points to the P IN on the R ING G UARD at the 1 o'clock position (Fig. 24). • Place the K NIFE and T OOL so the P IN on the K NIFE R EMOVAL T OOL is at the 11 o'clock position (Fig. 23). The S LOTS on the K NIFE R EMOVAL T OOL fit around the three P I ...

  • Hobart 3613 & 3713 - page 12

    – 12 – FORM 35218 (Oct. 2007) MAINTENANCE Unplug the machine power cord and turn the index knob fully clockwise t o close the gauge plate before doing any maintenance on the slicer. KNIFE SHARPENING The CleanCut TM K NIFE will provide long service in normal food retail or commercial kitchen use. Sharpen only when necessary; prolonged or too fre ...

Manufacturer Hobart Category Kitchen Utensil

Documents that we receive from a manufacturer of a Hobart 3613 & 3713 can be divided into several groups. They are, among others:
- Hobart technical drawings
- 3613 & 3713 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart 3613 & 3713
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart 3613 & 3713.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart 3613 & 3713, service manual, brief instructions and user manuals Hobart 3613 & 3713. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart 3613 & 3713.

Similar manuals

A complete manual for the device Hobart 3613 & 3713, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart 3613 & 3713 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart 3613 & 3713.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart 3613 & 3713 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart 3613 & 3713, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart 3613 & 3713, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart 3613 & 3713 - which should help us in our first steps of using Hobart 3613 & 3713
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart 3613 & 3713
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart 3613 & 3713 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart 3613 & 3713?

Use the form below

If you did not solve your problem by using a manual Hobart 3613 & 3713, ask a question using the form below. If a user had a similar problem with Hobart 3613 & 3713 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)