English dropdown-ico

Manual Poulan 435555

40 pages 2.95 mb
Download

Go to site of 40

Summary
  • Poulan 435555 - page 1

    OWNER'S MANUAL MODEL NUMBER: PP291E30 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 435555 Rev 3 08.09.10 TH Printed in U.S.A. ...

  • Poulan 435555 - page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...

  • Poulan 435555 - page 3

    3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u - fac tured to give best possible dependability and per for - mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the prope ...

  • Poulan 435555 - page 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (3) RET AINER SPRINGS (169675) (1) WASHER 3/8 (19131316) (1) L OCKNUT 3/8 (73800600) SAFTEY IGNITION KEY(S) (422663) (1) MUL TI- WRENCH (180684) (1) L OCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) L OCKNUT 1/4-20 (191730) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING (184505) (1) PO ...

  • Poulan 435555 - page 5

    5 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory with the ex cep tion of t ...

  • Poulan 435555 - page 6

    6 AS SEMBL Y / PRE-OPERA TION INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower . 1. Remove plastic tie securring rod to lower handle. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. S ...

  • Poulan 435555 - page 7

    7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotator head over chute bracket. If ...

  • Poulan 435555 - page 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...

  • Poulan 435555 - page 9

    9 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power - pro pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di- rec tion t ...

  • Poulan 435555 - page 10

    10 TO CONTROL SNOW DISCHARGE (See Fig. 13) WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup. If the discharge chute or au ger become clogged, shu ...

  • Poulan 435555 - page 11

    11 OPERA TION TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . USING THE CLEAN-OUT TOOL (See Fig. 15) In certain snow conditions, the disc ...

  • Poulan 435555 - page 12

    12 BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 19) The engine on your snow thrower has been shipped from the factory already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level ...

  • Poulan 435555 - page 13

    13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure you ...

  • Poulan 435555 - page 14

    14 SAE 5W -30 Motor Oil See “ENGINE” in Maintenance section General Purpose Grease GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad j ...

  • Poulan 435555 - page 15

    15 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower ...

  • Poulan 435555 - page 16

    16 SERVICE AND ADJUSTMENTS BEL T COVER SCREWS FRAME FIG. 21 TO REMOVE BEL T COVER (See Fig. 21) 1. Remove the two (2) screws securing belt cover to frame. 2. Remove belt cover . • Replace belt cover by installing cover and screws and tighten securely . WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure ...

  • Poulan 435555 - page 17

    17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou ...

  • Poulan 435555 - page 18

    18 SERVICE AND ADJUSTMENTS ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service center/department. ENGINE SPEED Never tamper with the engine ...

  • Poulan 435555 - page 19

    19 STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. Allow the ...

  • Poulan 435555 - page 20

    20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit ...

  • Poulan 435555 - page 21

    21 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 2 3 (5x) 4 ...

  • Poulan 435555 - page 22

    22 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 10 11 11 11 1 ...

  • Poulan 435555 - page 23

    23 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO ...

  • Poulan 435555 - page 24

    24 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO ...

  • Poulan 435555 - page 25

    25 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO ...

  • Poulan 435555 - page 26

    26 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . ...

  • Poulan 435555 - page 27

    27 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . ...

  • Poulan 435555 - page 28

    28 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P AR ...

  • Poulan 435555 - page 29

    29 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 2 3 3 4 4 3 3 01.08.004-B 4 4 KEY P AR ...

  • Poulan 435555 - page 30

    30 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 11 1 ...

  • Poulan 435555 - page 31

    31 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 10 10 ...

  • Poulan 435555 - page 32

    32 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 9 9 11 11 11 1 2 3 21 5 6 12 13 14 15 20 1 ...

  • Poulan 435555 - page 33

    33 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART ...

  • Poulan 435555 - page 34

    34 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 1a 1b 1b 4 ...

  • Poulan 435555 - page 35

    35 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . ...

  • Poulan 435555 - page 36

    36 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . ...

  • Poulan 435555 - page 37

    37 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) WHEELS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 1 2 01-06 ...

  • Poulan 435555 - page 38

    38 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KE ...

  • Poulan 435555 - page 39

    39 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003001) DECALS 1 181037 DECAL, DANGER 2 181042 DECAL, DA ...

  • Poulan 435555 - page 40

    LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser , we will repair or replace, at our option, without charge for parts or labor incurred in repla ...

Manufacturer Poulan Category Snow Blower

Documents that we receive from a manufacturer of a Poulan 435555 can be divided into several groups. They are, among others:
- Poulan technical drawings
- 435555 manuals
- Poulan product data sheets
- information booklets
- or energy labels Poulan 435555
All of them are important, but the most important information from the point of view of use of the device are in the user manual Poulan 435555.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Poulan 435555, service manual, brief instructions and user manuals Poulan 435555. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Poulan 435555.

Similar manuals

A complete manual for the device Poulan 435555, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Poulan 435555 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Poulan 435555.

A complete Poulan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Poulan 435555 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Poulan 435555, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Poulan 435555, that we can find in the current document
3. Tips how to use the basic functions of the device Poulan 435555 - which should help us in our first steps of using Poulan 435555
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Poulan 435555
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Poulan 435555 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Poulan 435555?

Use the form below

If you did not solve your problem by using a manual Poulan 435555, ask a question using the form below. If a user had a similar problem with Poulan 435555 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)