English dropdown-ico

Manual Agilent Technologies E3630A

27 pages 0.72 mb
Download

Go to site of 27

Summary
  • Agilent Technologies E3630A - page 1

    DUA L OUTPUT POWER SUPP L Y A gi lent MO DEL E3630A OPERA TING A ND SER VICE MA NUAL FOR INSTRUMENTS WITH SERIA L NUMBERS KR85014528 A ND A BOVE For instruments with Serial Numbers above KR85014528, a change page may be included . Manual Part No. 5959-5329 I April 2000 Edition 7 ...

  • Agilent Technologies E3630A - page 2

    1-2 SA FETY SUMMARY The following general safety prec autions must be observed during all phases of oper ation, service, and repair of this instrumen t. Failure to com ply with thes e precautions or with spec ific warnings elsewhere in this manual v iolates safety standards of des ign , manufacture, and intended use of the inst rument. A gilent T e ...

  • Agilent Technologies E3630A - page 3

    1-3 T able of Contents SA FETY SUMM A RY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 GENERA L INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 INTRODUCTIO N . . . . . . . . . . . . . . ...

  • Agilent Technologies E3630A - page 4

    1-4 GENERAL INFORMATION IN TRO DU CTI ON This section contains general i nformation concerning the E3630A triple output pow er supply. Included are safety con- siderations, safety and EM C requirements, inst rument and manual ident ification, option and ac cessory inf ormation, instrument descript ion, and specifications. SAFETY CONSIDER A TI ONS T ...

  • Agilent Technologies E3630A - page 5

    1-5 mode. In this mode the voltage of the negative output can be set lower than that of the positive output. T he tracking ratio control allows the negative supply 's output to be set to any va lue between a max imum that is within ±5% of the positive supply 's output and a minimum that is less than 0.5 volts. Once a ratio is estab lishe ...

  • Agilent Technologies E3630A - page 6

    1-6 INST A LLA TION INITIA L INSPE CTION Before s hipment, this instrument w as inspected and found t o be free of mecha nical and e lectrical defects. As soon as the instrument is unpacked, inspect for any dam age that may have occurred in t ransit. Sav e all packing m aterials until the inspection is com pleted. If damage is found, a c laim shoul ...

  • Agilent Technologies E3630A - page 7

    1-7 Before applying power to the supply , check the label on the heat sink t o mak e certain that the supply's line voltage option agrees wit h the line voltage to be used . If the opti on does not correspond to your line voltage, refer to paragraph "LI NE VOL T AG E OPTION CONVERSIO N" in the service section before applying power. T ...

  • Agilent Technologies E3630A - page 8

    1-8 Figure 3. Current Limit Characteristic of the 6V Supply this region. If the line voltage is maintained in the up per end of the input voltage range, howev er , the supply pr obably w ill operate within its specifications Connecting Load Each load should be connected t o the power supp ly output terminals using separate pairs of connect ing wire ...

  • Agilent Technologies E3630A - page 9

    1-9 Figure 4. Rev ers e Cur rent L oading S olution ...

  • Agilent Technologies E3630A - page 10

    A-1 SERVICE INFORMA TION Figure A- 1. Blo ck Di agram PRINCIPLES OF OP ERA TION (Blo ck Diagr am Over view) This sect ion presents t he principles of operation of t he E3630A Triple Out put Power S upply . T hroughout this discus- sion, refer to bot h the block d iagram of Figure A-1 and the schematic diagrams at the rear of the manual. The t wo pr ...

  • Agilent Technologies E3630A - page 11

    A-2 put is enclosed by a heavy line in Figure 3 of the operating section. If the operating point reaches the diagonal current limit line, a dec rease in load r esistance moves the op erating point down the line, reducing the out put voltage and current . Current foldback is controlled by a secon d operational ampli- fier (current comparison amplifi ...

  • Agilent Technologies E3630A - page 12

    A-3 Operation V erification T ests The followin g tests assure that the power suppl y is per- formin g properl y . The y do not, however , check all the speci- fied parameters tested in the complete performance test described below . Proceed as follows: a. Perform turn-on checkout procedure g iven in pa g e 1-7. b. Perform the load re g ulation per ...

  • Agilent Technologies E3630A - page 13

    A-4 Output Current Measurement. For accurate output current measurements, a current sampling resistor should be inserted between the load and the output of the supply . T o simplify grounding problems, one end of this sampli ng resistor shoul d be connected to the same output terminal of the supply which w ill be shorted to ground. An accurate vol ...

  • Agilent Technologies E3630A - page 14

    A-5 Current Limit k. Disconnect all loads from the suppl y . l. Connect the test setup shown in Fi g ure A-5 to the +20- volt output. Substitute a short for R L and leave the load circuit switch open. m. Set the volta g e of the ± 20V supplies to 20 volts. n. Close the load switch and determine the current flow throu g h the current samplin g resi ...

  • Agilent Technologies E3630A - page 15

    A-6 Peak-to-Peak Measurement The peak-t o-peak measurem ent is particularly i mportant for applications where noise spikes could be detrimental to a sensitive load, such as logic circuitry. T o measure the ripple and noise of the peak-to-peak value on each output supply output: a. Connect the test equipment across the output of the +20V supply as s ...

  • Agilent Technologies E3630A - page 16

    A-7 St ability (Drift) Definiti on: The change in output voltage (dc to 20 Hz) for the first 8 hours following a 30-minute w arm-up period with con- stant input line voltage, constant load resistance and constant ambient tem perature. T o me asure the stability : a. Connect the test equipmen t across the output of the +20V supply as shown in Figure ...

  • Agilent Technologies E3630A - page 17

    A-8 T a ble A -3 . Ini tial T robles hooting Procedu re STE P ACTION RESPONS E NEXT A CT ION 1 Check output voltage of +20V supply . a. Normal b. Zero volts c. Output voltage low er or higher than rat ing a. Proceed to step (2) . b. Check ac line fuse (F1). If blow n, proceed to "Open F use Troubleshooting" paragraph. If not blown, check ...

  • Agilent Technologies E3630A - page 18

    A-9 Low outpu t voltage (lower t han rating) 1. Measure voltage at t he base of Q5. 2. Eliminate current limit circuit as a source of trouble by disc onnecting anode of CR1 1. 3. Measure voltage at pin 3 of U6. a. Measured voltage is less than 0 vol t. b. Measures voltage is more than 0 vol t. a. Out put voltage increas es. b. Out put voltage remai ...

  • Agilent Technologies E3630A - page 19

    A-10 T able A-7. +6 V Su pply T r oubl eshooti ng SYMPTOM STEP - A CTION RE SPONSE P ROBA BLE CA USE The +20V supply must operat e properly before tr oubleshooting the -20V supply . High output voltage (higher than rat ing) 1. Atte mpt to turn of f Q1 by shorting emitt er-to-base of Q1. 2. Measure voltage at base of Q4. a. Outpu t voltage remains h ...

  • Agilent Technologies E3630A - page 20

    A-11 A DJ USTMENT A ND CA LIBR A TION Current Limit Adjustme nt +6V S upply. T o adjust the current limit circuit in t he +6V sup- ply , proceed as follows: a. Check the setting of the current limit by performing steps (p) and (q) on page A-5. (Be sure to set the output voltage to 6 volts.) If reducing the load resistance permits the cur- rent to e ...

  • Agilent Technologies E3630A - page 21

    A-12 REPL A C EA BLE P A RT S IN TRO DU CTI ON This section contains informat ion for ordering replacement parts. T able A-12 lists parts by reference designators and pro- vides the following information: a. Reference designators. Refer to T able A-10. b. Agilent T echnologies Part Number . c. T otal quantity us ed in that as sembly. d. Description ...

  • Agilent Technologies E3630A - page 22

       REFERE NCE DESIGNATION PART NUMBER Q'T Y DESCRIPTION MFR. CODE MFR. P/N        ...

  • Agilent Technologies E3630A - page 23

      REFERE NCE DESIGNATION PART NUMBER Q'TY DESCRIPTION MFR. CODE MFR. P/N    )"*'#? ...

  • Agilent Technologies E3630A - page 24

       REFERE NCE DESIGNATION PART NUMBER Q'TY DESCRIPTION MFR. CODE MFR. P/N     &*'&? ...

  • Agilent Technologies E3630A - page 25

       REFERE NCE DESIGNATION PART NUMBER Q'TY DESCRIPTION MFR. CODE MFR. P/N ,   !!& ! ...

  • Agilent Technologies E3630A - page 26

    CERTIFICATION Agilent T ec hnologies c ertifies that this pr oduct m et its published s pecificat ions at time of sh ipmen t fro m t he fa ctor y . Agilent T ech nologies furt her cert ifies that its ca libration m easurem ents are trac eable t o the United St ate s Nat ional Ins titute of Stan- dards and T echnolo gy (form erly National Bure au of ...

  • Agilent Technologies E3630A - page 27

    DECLA RA TION O F CONFORMITY accordi ng to ISO/IEC Guid e 22 and EN 4 5014 Manufactu rer’s Name: Agilent Techno logies, In c. Manufactu rer’s Address: 3 45-15, Kasa n-dong, Kum chon-ku, Seoul 15 3-023 Korea declares, that the produc ts Product Na me: DC Power Supply Model Numbers : E3630A Product Opt ions: Al l Options conforms to the follow in ...

Manufacturer Agilent Technologies Category Power Supply

Documents that we receive from a manufacturer of a Agilent Technologies E3630A can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- E3630A manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies E3630A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies E3630A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies E3630A, service manual, brief instructions and user manuals Agilent Technologies E3630A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies E3630A.

Similar manuals

A complete manual for the device Agilent Technologies E3630A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies E3630A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies E3630A.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies E3630A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies E3630A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies E3630A, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies E3630A - which should help us in our first steps of using Agilent Technologies E3630A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies E3630A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies E3630A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies E3630A?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies E3630A, ask a question using the form below. If a user had a similar problem with Agilent Technologies E3630A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)