English dropdown-ico

Manual Makita 3703

20 pages 0.94 mb
Download

Go to site of 20

Summary
  • Makita 3703 - page 1

    TLimmer Collet chuck capacity 114” 1/4” MODEL 3703 Overall length Net weight No load speed (RPMI 30,000 247 mm (9-23132”) 1.5 kg (3.3 lbsl INSTRUCTION MANUAL DOUBLE INSULATION ...

  • Makita 3703 - page 2

    IMPORTANT SAFETY IN STRU CTI 0 N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. a. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invi ...

  • Makita 3703 - page 3

    14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...

  • Makita 3703 - page 4

    ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. 4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Make sure ...

  • Makita 3703 - page 5

    Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Insert the bit all the way into the collet cone and tighten the collet nur securely with the two wrenches. To remove the bit, follow the installation procedure in reverse. CAUTION : 0 Do not tighten the coll ...

  • Makita 3703 - page 6

    Operation .Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed. Move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete. 0 When doing edge cutting, the workpiece surface should be on ...

  • Makita 3703 - page 7

    Straight guide (Optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Remove the chip deflector. Attach the straight guide with the clamp screw (A). Loosen the wing nut on the straight gu ...

  • Makita 3703 - page 8

    Circular work 0 Circular work may be accomplished if you assemble the straight guide and guide plate 0 Min. and max. radius of circles to be cut (distance between the center of circle and the as shown in the figure below. center of bit) are as follows : Min. : 70 mm (2-3/4") Max. : 221 mm (8-1 1/16") (Note) Circles between 172 mm (6-3/4&q ...

  • Makita 3703 - page 9

    Trimmer guide Trimming, curved cuts in veneers for fur- niture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Install the trimmer guide on the tool base with the clamp screw (A). Loosen the clamp screw (B) and adjust the distance between the bit and the trimmer guide by turning the a ...

  • Makita 3703 - page 10

    Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Remove the chip deflector. Loosen the screws and remove the base protector. Place the templet guide on the base and re- place the base protector. Then secure the base protector by tightening the screws. Secure the templ ...

  • Makita 3703 - page 11

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes I regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be ...

  • Makita 3703 - page 12

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Straight guide assembly Part No. 123008-8 0 ...

  • Makita 3703 - page 13

    Bits STRAIGHT -Single Flute HIGH SPEED STEEL PART NO. A B C D E 7332328A 1 /8 5/16 1-1/8 1 /4 1-518 STRAIGHT - 2 Flute CARBIDE TIPPED PART NO. A B C D E 733003-2A 3/16 7/16 1 -3/8 114 2 733003-4A 114 3/4 1-3/16 114 2-1/8 733003-EA 5/16 1 1-1/8 114 2-3/16 HIGH SPEED STEEL (STRAIGHT - 2 Flute) PART NO. A B C D E 7332334A 5/16 7/8 1-3/16 1 /4 2-1/8 HI ...

  • Makita 3703 - page 14

    ROUND NOSE -I+ CARBIDE TIPPED PART NO. A B C D E 733008-2A 1 I4 15/32 1-114 114 1-7lJ 7330084A 318 9/16 1-114 1 I4 2 CORE BOX 4DC HIGH SPEED STEEL PART NO. A B C D E 733238-2A 1 I4 114 1-3116 1 I4 1-112 VEE GROOVING CARBIDE TIPPED PART NO. A E C D E e 733009-2A 318 112 1-3/16 114 2 90" 14' DOVE TAIL 4DC CARBIDE TIPPED PART NO. A B C D E 7 ...

  • Makita 3703 - page 15

    PANEL PILOT HIGH SPEED STEEL PART NO. A B C D E 733236-0A 1 /4 3/4 1 1 /4 2-7/16 CORNER ROUNDING CARBIDE TIPPED - Ball Bearing Pilot 733120-OA 718 1/2 3/8 1-1/4 1-15/16 3/16 733120-2A 112 1/2 1-1/4 1/4 1 /4 REPLACEMENT BEARING - NO 733132-4A HIGH SPEED STEEL - Solid Pilot PARTNO. Ai AI 8 C D E R 733240-2A 11/16 3/16 112 1 1/4 1-3/4 1/4 733240-6A 15 ...

  • Makita 3703 - page 16

    ROMAN OGEE -ID!? CARBIDE TIPPED - Ball Bearing Pilot B D PARTNO. A1 A1 C E R 2 5/32 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO. 733132-2A FLUSH TRIMMER -Self Piloting CARBIDE TIPPED - Ball Bearing Pilot B D PARTNO. A1 A1 C E R 2 5/32 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO. 733132-2A FLUSH TRIMMER -Self Piloting SOLID ...

  • Makita 3703 - page 17

    COMBINATION FLUSH/22" BEVEL TRIMMER 2 CARBIDE TIPPED 733129-2A 518 318 1-1/4 1 /4 2-318 REPLACEMENT BEARING - NO. 733132-6A PART NO. A BI 82 C D E 733128-6A 7/16 1 /2 3/16 1-1/4 1/4 1-3/4 3 FLUTE FLUSH TRIMMER ASSEMBLY -Self Piloting 4DC SOLID CARBIDE CUTTER PART NO A B C D E 1 3 FLUTE 22" BEVEL TRIMMER ASSEMBLY -Self Piloting SOLID CARBI ...

  • Makita 3703 - page 18

    3 FLUTE 22' BEVEL REPLACEMENT CUTTER L B pj I SOLID CARBIDE I PARTNO. A B D I 733129-8A 7/8 318 114 FOR BEVEL TRIMMER ASSEMBLY NO. 733129-4A ~~ ~~ 1/4" REPLACEMENT ARBOR I PARTNO. A B C D El I 733131-2A 518 318 1-1/4 1 I4 2-318 I FOR FLUSH TRIMMER ASSEMBLY NO. 733129-2A AND NO. 733129-4A BALL BEARING PILOT I PARTNO. D1 D, 1 733132-2A 3/8 ...

  • Makita 3703 - page 19

    Mar.-26-'90 US 114" TRIMMER 19 ...

  • Makita 3703 - page 20

    MODEL 3703 Mar.-26-'90 US p.. ITEM AtD DESCRIPTION 'iiM GtD DESCRIPTION . MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 3 2 1 1 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 - Name Plate Pan Head Screw M4x40 (With Washer) Pan Head Screw M4x14 IWith Washed Strain Relief Rear Cover Cord Cord Guard Motor Rear Housing Brush Holder Ca ...

Manufacturer Makita Category Trimmer

Documents that we receive from a manufacturer of a Makita 3703 can be divided into several groups. They are, among others:
- Makita technical drawings
- 3703 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita 3703
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita 3703.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita 3703, service manual, brief instructions and user manuals Makita 3703. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita 3703.

Similar manuals

A complete manual for the device Makita 3703, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita 3703 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita 3703.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita 3703 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita 3703, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita 3703, that we can find in the current document
3. Tips how to use the basic functions of the device Makita 3703 - which should help us in our first steps of using Makita 3703
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita 3703
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita 3703 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita 3703?

Use the form below

If you did not solve your problem by using a manual Makita 3703, ask a question using the form below. If a user had a similar problem with Makita 3703 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)