English dropdown-ico

Manual Husqvarna Rider 15V2s AWD

40 pages 2.96 mb
Download

Go to site of 40

Summary
  • Husqvarna Rider 15V2s AWD - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 15V2 Rider 15V2 AW D Rider 15V2s A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna Rider 15V2s AWD - page 2

    2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ................................................... 3 INTR ODUCTION Dear Customer , ..................... ...

  • Husqvarna Rider 15V2s AWD - page 3

    English – 3 Ser vice journal Pre-deliver y service 1 1a. Dry-charged battery (506788801) Fill the batter y with batter y acid and charge f or 4 hours at max. 6 amp. 1b. Wet-char ged battery (510138501) Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure (60 Kpa, 0 ...

  • Husqvarna Rider 15V2s AWD - page 4

    4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency e ven in small or confined areas. The closely grouped controls and pedal-operated h ydrostati ...

  • Husqvarna Rider 15V2s AWD - page 5

    English – 5 INTR ODUCTION Good ser vice Husqv arna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer , get the best suppor t and ser vice. For e xample, before this machine w as delivered it was inspected and adjusted b y your dealer . See the cer tificate in the Ser vice Jour nal i ...

  • Husqvarna Rider 15V2s AWD - page 6

    6 – English KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed he ...

  • Husqvarna Rider 15V2s AWD - page 7

    English – 7 KEY T O SYMBOLS Chec k the engine’ s oil lev el Check tr ansmission oil lev el Lift up the cutting unit Apply the parking brake . If the engine is cold, use the choke Release the parking brake bef ore dr iving ...

  • Husqvarna Rider 15V2s AWD - page 8

    8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are f or your saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider. • Contact your insur ance company . • Y ou should hav e fully comprehensive insurance including: third par ty , fire, damage, theft and liability G ...

  • Husqvarna Rider 15V2s AWD - page 9

    English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment. • Ne ver w ear loose fitting clothes that can catch in moving par ts. • Ne ver use the ...

  • Husqvarna Rider 15V2s AWD - page 10

    10 – English SAFETY INSTR UCTIONS • F ollow the manuf acturer’s recommendations regarding wheel weights or counterbalance weights to increase machine stability . Children • Serious accidents may occur if y ou f ail to be on your guard f or children in the vicinity of the machine. Children are often attracted to the machine and mowing. Nev e ...

  • Husqvarna Rider 15V2s AWD - page 11

    English – 11 SAFETY INSTR UCTIONS • Make sure all n uts and bolts are tightened correctly and that the equipment is in good condition. • Do not modify saf ety equipment. Check regularly to be sure it works properly . The machine must not be driven if protective plates , protectiv e cov ers, saf ety switches or other protective de vices are no ...

  • Husqvarna Rider 15V2s AWD - page 12

    12 – English WHA T IS WHA T? Location of the contr ols 1 Choke control 2 Switch f or the lights 3 Throttle control 4 Ignition lock 5 Counter 6 Cutting height adjustment le ver 7 Lifting le ver f or the cutting unit 8 Speed limiter f or rev ersing 9 Speed limiter f or driving forward 10 P arking brake 11 Lock b utton f or parking brake 12 Seat adj ...

  • Husqvarna Rider 15V2s AWD - page 13

    English – 13 PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for many y ears. This operator’ s manual describes Rider 15V2, Rider 15V2s A WD and Rider 15V2 A WD . The machines are equipped with a 15 horse power engine from Kaw asaki. The machines are equipped with ...

  • Husqvarna Rider 15V2s AWD - page 14

    14 – English PRESENT A TION Cutting unit Rider 15V2, Rider 15V2s A WD and 15V2 A WD can be equipped with two diff erent cutting units. • Combi 1030mm/41” • Combi 1120 mm/44” The Combi-unit, equipped with a BioClip-plug, finely chops the cuttings to f er tiliser . Without the BioClip-plug the unit works in the same wa y as a rear ejection ...

  • Husqvarna Rider 15V2s AWD - page 15

    English – 15 PRESENT A TION The seat can also be adjusted lengthw ays. T o adjust move the le ver under the front edge of the seat to the left, so that the seat can be mov ed f orward or bac kwards to the required position. Fuelling The engine runs on unleaded petrol with a minimum octane rating of 87 (not mix ed with oil). We recommend the use o ...

  • Husqvarna Rider 15V2s AWD - page 16

    16 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. Start the engine 1 Make sure that the clutch control is depressed. Rider 15V2 A WD has one control fo ...

  • Husqvarna Rider 15V2s AWD - page 17

    English – 17 Driving 8 Let the engine run at moderate speed or half throttle for 3- 5 minutes bef ore subjecting it to heavy load. 9 Set the required engine speed with the throttle control. Starting the engine with a weak battery If the battery is too weak to star t the engine, it should be recharged. When jump leads are used f or emergency star ...

  • Husqvarna Rider 15V2s AWD - page 18

    18 – English Driving 4 Press in the lock b utton on the lifting le ver and lo wer the cutting unit. Cutting tips • Localise and mark stones and other fixed objects to a void collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained. • The mowing result will be best with the highest permit ...

  • Husqvarna Rider 15V2s AWD - page 19

    English – 19 Maintenance Maintenance sc hedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) If the machine is used daily it should be lubricated twice a week. 2) Maintenance and replacement are required more often in d ...

  • Husqvarna Rider 15V2s AWD - page 20

    20 – English Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure. Do not direct the jet tow ards electrical components or bearings. Do not rinse hot surfaces suc ...

  • Husqvarna Rider 15V2s AWD - page 21

    English – 21 Maintenance 1 Remov e the frame plate b y loosening the screws (2) and lift the frame plate b y the rear edge. 2 Check the tension of the steering wires by squeezing them together by the arro ws as illustrated. It should be possible to push them together so that the distance between them is half as much, without using unnecessary f o ...

  • Husqvarna Rider 15V2s AWD - page 22

    22 – English Maintenance 1 Loosen the clamping screw f or the cable’ s outer casing and mov e the throttle to the full throttle position. 2 Check that the throttle wire is attached to the correct hole in the lower le ver , see diagram. 3 Pull the throttle wire casing to the f ar left and tighten the clamping screw . Chec king and adjusting the ...

  • Husqvarna Rider 15V2s AWD - page 23

    English – 23 Maintenance Alwa ys replace the paper filter every 200 hours. 7 Put the pre-filter and paper filter back into the air filter unit. 8 Put back the air filter unit b y first aligning the hooks on the bottom of the unit, then press it until the catches lock into position. Chec king the fuel pump’ s air filter Check regularly th ...

  • Husqvarna Rider 15V2s AWD - page 24

    24 – English Maintenance Chec k the safety system The machine is equipped with a saf ety system that prev ents star ting or driving under the following conditions . The engine should only be possible to start when the cutting unit is in its raised position and the h ydrostat pedals are in the neutral position. Rider 15V2 A WD , the engine can not ...

  • Husqvarna Rider 15V2s AWD - page 25

    English – 25 Maintenance Replacing the light b ulbs F or information about the bulb type , see T echnical Data. 1 Loosen the lock n ut and remov e the Allen bolt. Remove the steering wheel. 2 Unscrew the tw o screws holding the co ver on the po wer ser vo housing. One screw on each side. 3 Press in the parking lock button and lift the co v er ov ...

  • Husqvarna Rider 15V2s AWD - page 26

    26 – English Maintenance Chec king the engine’ s cooling air intake Clean the air intake g rille in the engine cover behind the driver’ s seat. Open the engine cov er . Check that the cooling intak e is free from leav es, grass and dir t. Check the air duct, located on the inside of the engine co ver , ensure it is clean and does not rub agai ...

  • Husqvarna Rider 15V2s AWD - page 27

    English – 27 Maintenance 7 Slide the unit in and inser t the pin. Make sure that the tongue (3) on the cutting unit engages correctly . 8 Fit the drive belt around the drive wheels of the cutting unit. 9 Hook up the height adjustment strut. 10 Mov e the suppor t wheels to their parking position. 11 Fit the front cov er . 12 Secure the collet spri ...

  • Husqvarna Rider 15V2s AWD - page 28

    28 – English Maintenance 5 Adjust the unit’ s ground pressure by screwing in or out the adjusting screws located behind the front wheels on both sides. The ground pressure should be between 12 and 15 kg (26.5-33 lb). Chec king the cutting unit’ s parallelism Check the cutting unit’ s parallelism as f ollows: 1 Check the air pressure in the ...

  • Husqvarna Rider 15V2s AWD - page 29

    English – 29 Maintenance Placing in the service position 1 P osition the machine on flat ground. Apply the par king brak e. Adjust the cutting unit to the lowest cutting height and lower the cutting unit. 2 Remov e the front hood by remo ving the pin. (There are complete instructions on using the ser vice position inside the front hood). 3 Remov ...

  • Husqvarna Rider 15V2s AWD - page 30

    30 – English Maintenance 8 Lift of the drive belt. Then pull out the pin. 9 Pull the frame f orwards and refit the pin. 10 Grasp the front edge of the cutting unit, pull out and raise into the ser vice position. If the cylindrical bolt, which is now holding the cutting unit is remov ed, the cutting unit can be lifted off . Restoring fr om servic ...

  • Husqvarna Rider 15V2s AWD - page 31

    English – 31 Lubrication Chec king the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again, without tightening it. Pull the dipstick out again and read the oil le vel. The o ...

  • Husqvarna Rider 15V2s AWD - page 32

    32 – English Lubrication Fill with new oil according to Chec king the engine’ s oil lev el. Star t the engine and let it idle for about 3 min utes. Now stop it and check f or signs of leakage. Fill with oil to compensate f or the oil held in the new oil filter . Chec king the transmission oil level 1 Remov e the transmission co ver . Undo the ...

  • Husqvarna Rider 15V2s AWD - page 33

    English – 33 T roub leshooting schedule Prob lem Procedure Engine does not star t There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir t in the carburettor or fuel line Star ter motor does not tur n ov er the engine Star ter motor does not tur n ov er the engine Batter y flat Bad cont ...

  • Husqvarna Rider 15V2s AWD - page 34

    34 – English Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine. Fuel stabilise ...

  • Husqvarna Rider 15V2s AWD - page 35

    English – 35 T echnical data 1) As rated b y the engine manuf acturer Dimensions Rider 15V2 Rider 15V2 A WD Rider 15V2s A WD Length without cutting unit, mm/ft 2020/6,61 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 880/2,89 880/2,89 880/2,89 Height, mm/ft 1070/3,52 1070/3,52 1070/3,52 Operating weight with cutting dec k, kg/lb 268-274/59 ...

  • Husqvarna Rider 15V2s AWD - page 36

    36 – English T echnical data EC-dec laration of conformity (Applies to Eur ope only) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 15V2, Rider 15V2 A WD and Rider 15V2s AWD from 2008’ s ser ial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subse ...

  • Husqvarna Rider 15V2s AWD - page 37

    ...

  • Husqvarna Rider 15V2s AWD - page 38

    ´®z+S!r¶6H¨ ´®z+S!r¶6H¨ ...

  • Husqvarna Rider 15V2s AWD - page 39

    ...

  • Husqvarna Rider 15V2s AWD - page 40

    ´®z+S!r¶6H¨ 2009-05-11 ´®z+S!r¶6H¨ 1151018-26 ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna Rider 15V2s AWD can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- Rider 15V2s AWD manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna Rider 15V2s AWD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna Rider 15V2s AWD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna Rider 15V2s AWD, service manual, brief instructions and user manuals Husqvarna Rider 15V2s AWD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna Rider 15V2s AWD.

Similar manuals

A complete manual for the device Husqvarna Rider 15V2s AWD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna Rider 15V2s AWD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna Rider 15V2s AWD.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna Rider 15V2s AWD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna Rider 15V2s AWD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna Rider 15V2s AWD, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna Rider 15V2s AWD - which should help us in our first steps of using Husqvarna Rider 15V2s AWD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna Rider 15V2s AWD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna Rider 15V2s AWD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna Rider 15V2s AWD?

Use the form below

If you did not solve your problem by using a manual Husqvarna Rider 15V2s AWD, ask a question using the form below. If a user had a similar problem with Husqvarna Rider 15V2s AWD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)