English dropdown-ico

Manual Edimax PS-1206MF

61 pages 4.65 mb
Download

Go to site of 61

Summary
  • Edimax PS-1206MF - page 1

    ...

  • Edimax PS-1206MF - page 2

    Copyright © by Edimax T echnology Co, L TD. all rights reserved. N o part of this publi cation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior writ ...

  • Edimax PS-1206MF - page 3

    Federal Communication Commission Interference S t atement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can ra ...

  • Edimax PS-1206MF - page 4

    Federal Communication Commissi on (FCC) Radiation Exposure Statement This equipment complies with FCC r adiation exposure set forth for an uncontrolled environment. In order to avoi d the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. T ...

  • Edimax PS-1206MF - page 5

    RSS-210 Compliance S t atement The term “IC:” before the ce rtification/registration num ber only signifies that Industry Canada technical specifications we re met. Operation is subject to the following two conditions: (1) this devic e may not cause interference, and (2) this device must accept any interference, including interference that may ...

  • Edimax PS-1206MF - page 6

    R&TTE Compliance S t atement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN P ARLIAM ENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and repl aces in the directive ...

  • Edimax PS-1206MF - page 7

    Regulatory Approvals for AC Adapter Input: AC 100-240 V , 50-60 Hz Output: DC 5V , 1.0A Power Consumption: 300mW Safety S tandards: UL/CUL 60950-1 EMC: FCC part 15 subp art B Class B ...

  • Edimax PS-1206MF - page 8

    Safety Information For your safety , be sure to read and fo llow all warning notices and instructions. • Do not continue operating if you noti ce smoke or unusual odors or sounds. Continued operation may result in electr ic shock or fire. Immediately turn off power and remove the power adapt er from the outlet, then cont act EPSON. • Do not dis ...

  • Edimax PS-1206MF - page 9

    • Make sure to connect the c ables to the correct ports . • Place connecting cables carefully so that no one will step on them or stumble over them. • A void locations that are subject to rapid changes in heat or humidity , shocks or vibrations, or dust. • Do not expose the device to dampness, dust or corrosive liquids. • Discontinue use ...

  • Edimax PS-1206MF - page 10

    Content s 1. Introduction ...................................................................... 1 2. MFP Server Modes .......................................................... 2 3. Using Y our All-in-one in MAC ........................................... 4 3.1 Printing ............................................................................. ...

  • Edimax PS-1206MF - page 11

    6.5.1 Load Defaul t ...................................................................... 46 6.5.2 Upgrade Firmw are ............................................................. 47 7. T roubleshooting ............................................................. 48 ...

  • Edimax PS-1206MF - page 12

    1 1. Introduction This MFP Server allows your all-in-one printer to become a shared device on the network. Unlike many MFP Servers, it can communicate with your all-in-one printer as if it was connected directly to your computer . This allows all users to share print, scan, card reader and fax (if available) over the network. Y ou can also monitor ...

  • Edimax PS-1206MF - page 13

    2 2. MFP Server Modes This MFP Server support s two modes : All-in-one MFP Server Mode and MFP Server Mode. Users can choose one of these modes to share all-in-one or printer functions through the MFP Server . All-in-one MFP Server Mode: The MFP Server can communicate with an all-in-one printer as if it was connected directly to your computer . Thi ...

  • Edimax PS-1206MF - page 14

    3 MFP Server Mode: The MFP Server also support s LPR, IP P and RA W printing protocols, which enable users to share the print functi on from an all-in-one printer . The supported Operating Systems are Windows 98SE/Me/NT/2000/XP/2003/Vista and MAC. For detailed instructions, pl ease refer to the following chapters. Chapter 7: LPR Printing Chapter 8: ...

  • Edimax PS-1206MF - page 15

    4 3. Using Your All-in-one in MAC After you have followed the inst all wizard to finish the all-in-one printer and MFP Server inst allation and manually add your all-in-one into printer list, you are able to start sharing print, scan, card reader , or fax functions. T o print, scan or read the memory card through MFP Server , please follow the step ...

  • Edimax PS-1206MF - page 16

    5 Tip: If you have finished using the all-in-one printer , please click “Disconnect” to release it. Other users can’t use the all-in-one printer until it is released. ...

  • Edimax PS-1206MF - page 17

    6 3.1 Printing After you manually add the all-in-one prin ter to “Printers and Faxes” in MAC. Y ou can select the printer for printi ng a document through MFP Server by following the steps below . Be sure to conne ct the all-in-one you want to use on the list of MFP manager first. Tip: If you have sent a print job to it while the all-in-one pri ...

  • Edimax PS-1206MF - page 18

    7 3.2 Scanning The all-in-one printer provides a scan utilit y for users. Y ou can scan pictures or documents through the utility . In MAC, you can also scan from the MAC scanning utility or use third party scanni ng utilities such as Photoshop, Photoimpact, Paint Shop Pro, etc. Be su re to connect the all-in-one you want to use on the list of MFP ...

  • Edimax PS-1206MF - page 19

    8 MAC Scanning Utility ...

  • Edimax PS-1206MF - page 20

    9 3.3 Reading Memory Cards Y ou can read the files from a memory ca rd through the MFP Server . Be sure to connect the all-in-one you want to use on the list of MFP manager first. ...

  • Edimax PS-1206MF - page 21

    10 4. MFP Manager in MAC 4.1 MFP Server List The “MFP Manager” can automatically find the MFP Server in the network and show it in the MFP Server List. You c an select an all-in-one printer and click “Connect” to use the printer as if you had directly connected the printer to your computer through a USB c able. The MFP manager also displays ...

  • Edimax PS-1206MF - page 22

    11 MFP Server List MFP Server List The “MFP Server List ” will list all the MFP Servers within the network. You can find information about the MFP Server including “MFP Server Name”, “MAC ID”, “IP Address” and the device that is connected to the MFP Server. MFP Server/MFP Information When you are clicking on the “MFP Server” in ...

  • Edimax PS-1206MF - page 23

    12 MFP Server List MFP Server/MFP Information Computer Name – It display the computer name of the user who is connecting to the all-in-one printer. Contact Information – When the current user has set his “Contact Information”, you can see it here. You can contact the current user to disconnect the all-in-one printer. Refresh Refresh the “ ...

  • Edimax PS-1206MF - page 24

    13 4.2 Option Settings 4.2.1 General Setting General Setting Run MFP Manager when MAC starts Execute the “MFP Manager” when MAC starts every time. By default, it is enabled. Minimized when start MFP Manager Minimize the “MFP Manager” to an icon in the system tray when you star t the “MFP Manager”. By default, it is enabled. Refresh stat ...

  • Edimax PS-1206MF - page 25

    14 4.2.2 Search for MFP Server If MFP Server is not in the same network as your computer , you can enter the IP Address of the MFP Server to do re mote search. The MFP Server in the “Remote MFP Server List” will be added to the “MFP Server List” for you to configure. Note: If the remote MFP Server you have searched is behind a NA T Router , ...

  • Edimax PS-1206MF - page 26

    15 5. Server Configuration in MAC 5.1 Introduction This chapter introduces the MFP Server ’s system configuration utility in MAC environment. This utility provides the most complete management and configuration functions on the MFP Serv er side. This utility only provides configuration functions for MFP Server itself; it does not include configur ...

  • Edimax PS-1206MF - page 27

    16 5.2 Search for All A vailable MFP Server T o run the “Server Manager” configur ation utility , click the “Search” button . Th e configuration utility will delay for seve ral seconds because the utility is using the system’s available network protocols to search for all MFP Servers on the network. All available MFP Servers will be liste ...

  • Edimax PS-1206MF - page 28

    17 5.3 S t atus of MFP Server ...

  • Edimax PS-1206MF - page 29

    18 Click the “S tatus” button on the tool bar . The status of the currently selected MFP Server will be shown on the right side of the window , go to ‘’System’’, ‘’Printer ’’, ‘’TCP/IP’ ’ and ‘’Wireless’’ for detail status. The information about the MFP Server includes Device Name, MF P Server Name, Model T ype, ...

  • Edimax PS-1206MF - page 30

    19 5.4 General Setting Double click the “General” button on t he tool bar . The setup items of the current selected MFP Server will be show n on the right side of the window . A screen will pop up to verify “User Name” and “Password” of the MFP Server . The default values are: User Name: admin, Password: 1234 . ...

  • Edimax PS-1206MF - page 31

    20 Tip: When you click save, a ‘’what to do’ ’ message will pop up, please click “Reboot” to restart the MFP Server to le t the settings take ef fect, or click ‘’cancel’ ’ to save the setting and go to further settings. Y ou can configure the “Server Name”, “User Name” and “Password” here. Server Name , the name of t ...

  • Edimax PS-1206MF - page 32

    21 5.5 TCP/IP Configuration Double click the “TCP/IP” button. The TC P/IP configuration window will pop up. Y ou can configure the MFP Server to aut omatically get an IP address from a DHCP server or manually specify a st atic IP . IP Address Assignment: If you need the MFP Server to automatically get an IP from a DHCP server , select “Auto I ...

  • Edimax PS-1206MF - page 33

    22 5.6 System Configuration Double click the “System” button. The System configurati on window will pop up. In the System configuration page, y ou can upgrade the firmware, reset to factory default, reboot the system or set the force release port for this MFP Server . Firmware Upgrade : Y ou can use this “Firmware Upgrade” tool to update to ...

  • Edimax PS-1206MF - page 34

    23 5.7 Wireless Configuration Wireless Configuration Doubl e-click the “Wireless” button. Enter user name and password then the wireless configur ation window will popup. The default username and password are ‘’admin’ ’ and ‘’ 1234’’, and you are into the step s of ‘’Infrastructure Mode”. Function: Y ou can select “Auto? ...

  • Edimax PS-1206MF - page 35

    24 wireless connection. Enable – Enable wireless functi on only; the MFP Server’s wireless LAN will be enabled and Ethernet will be disabled. Disable – Disable the wireless function, the MFP Server ’ s wireless LAN will be disabled and Ether net will be enabled. Infrastructure: Y ou have to let the MFP server associate with an access point. ...

  • Edimax PS-1206MF - page 36

    25 This MFP server support s WEP , WP A-PSK and WP A2-PSK security mode. If you want to use WEP encryption to prot ect your wireless network, you have to select “WEP’’. The wir eless security setting should match other wireless devices in the same network. WEP Security Mode: When you choose the encryption to ‘’WEP’ ’ a key format mess ...

  • Edimax PS-1206MF - page 37

    26 (p.s. this picture is temporary we will post the formal one later) Y ou can select to enter “10 or 26 charac ters” for “Hexadecimal” or “5 or 13 characters’ ’ for ‘’ASCII” format encryption key . Longer key length can provide stronger security but worse communication performance. Network Key –Simplifies the WEP encryptio n ...

  • Edimax PS-1206MF - page 38

    27 WP A-PSK/WP A2-PSK Security Mode: “WP A-PSK’’ and ‘’WP A2-PSK” can automatic ally transfer keys to TKIP or AES by random. Network Key – Enter 8 to 63 digits to be the key for authentication within the network. TKIP(WP A-PSK & WP A2-PSK) – TKIP (T emporal Key Integrity Protocol) changes the temporal key every 10,000 pa ckets. ...

  • Edimax PS-1206MF - page 39

    28 AES(WP A2-PSK) – AES has been developed to ensure the highe st degree of security and authenticity for digital in formation and it is the most advanced solution defined by IEEE 802.1 1i for security in a wireless network. When you finish configuring wireless secu rity , click “Save” and a ‘’What to do’’ message pop out. Please clic ...

  • Edimax PS-1206MF - page 40

    29 6. Web Management 6.1 Introduction The MFP Server can be configured and managed on the W eb. Through the Local Area Network, or even the Inte rnet, the administrator can easily configure and manage MFP Server’s vari ous main functions in a browser . Simply enter the MFP Server ’s IP address into your browser ’s address field to manage a MF ...

  • Edimax PS-1206MF - page 41

    30 6.2 Login Y ou may use any Web Browser to review t he status or configure the settings of the MFP Server . After entering the IP addr ess of the MFP Server , a login page displays. Y ou have to enter the correct “User Name” and “Password” before going to the Web Management p ages. Note: Default User Name is “admin”, default password ...

  • Edimax PS-1206MF - page 42

    31 6.3 Device S t atus 6.3.1 System Status System Information includes “Device Na me”, “MFP Server Name”, “Model T ype”, “Firmware V ersion”, “MAC Addre ss”, “Wireless Configuration”, and the protocols enabled status, etc. ...

  • Edimax PS-1206MF - page 43

    32 6.3.2 Printer Status This page list s information and status of the all-in-one printer or printer connected to the MFP Server port. The status of the all-in-one printer or printer includes “Connected”, ”Ready”, “Of f Line” or “Paper Out”. Connected: a user has clicked the “Connect” button in the “MFP Manager” utility . Th ...

  • Edimax PS-1206MF - page 44

    33 6.3.3 TCP/IP Status This page list s all TCP/IP settings of the MFP Server including “IP Address”, “Subnet Mask” and “Gateway”. It also can tell whether the DHCP server is “On” or “Off”. ...

  • Edimax PS-1206MF - page 45

    34 6.4 Setup Wizard Note: Y ou can configure the MFP Server from the Setup Wizard. T o let the changes take ef fect, you have to click “Save Settings” in the menu on the lef t side to reboot the MFP Server. 6.4.1 System 6.4.1.1 Admin Password Y ou can change the MFP Server name and port name from here. MFP Server Name : the name of the MFP Serv ...

  • Edimax PS-1206MF - page 46

    35 Y ou can change the MFP Server name and p assword from here. MFP Server Name : the name of the MFP Server . Y ou can use this name to identify the MFP Server when you are s earching for if using by the “Server Manager” utilities. Password: enter the password you want to change for the MFP Server . The password can be up to 7-6 digit s in al ...

  • Edimax PS-1206MF - page 47

    36 6.4.1.2 Advanced Settings Some advanced feature of the MFP Server can be set here. TCP/IP Printing (LPR/IPP/RA W) : The MFP Server supports TCP/IP network protocol and LPR/IPP/RA W printing prot ocols. By default these protocols are enabled. ...

  • Edimax PS-1206MF - page 48

    37 6.4.2 Wireless If you want to use the MFP Server th rough a wireless LAN, please set up the MFP Server through E thernet first and make sure your wireless LAN setting is correct. After setting the wireless LAN, unplug the Ethernet cable and restart the MFP Server . Then you can st art to use the MFP Server through the wireless LAN. If the wirele ...

  • Edimax PS-1206MF - page 49

    38 wireless LAN mode. The MFP Server default is in “Auto” mode. ESSID is the unique name identified by in a wireless LAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure that the ESSID of all stations and access points in the same WLAN network are the same. Channel Number is the channel number of your wireles ...

  • Edimax PS-1206MF - page 50

    39 6.4.2.1 Site Survey Y ou can use this “Site Survey” function to search for available access points in your location. In the list is the inform ation for all available access points or wireless stations, including SSID, BSSI D, Channel, T ype, Encryption and Signal S trength. Y ou can select one wireless device in the list for this MFP Server ...

  • Edimax PS-1206MF - page 51

    40 6.4.2.2 Encryption This MFP Server support s WEP and WP A- PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WP A-PSK, y ou have to select “WP A-PSK” (for an infrastructure network or “WP A-None” (enables WP A security for an ad hoc network). The wirele ...

  • Edimax PS-1206MF - page 52

    41 Default Key – Select one of the four keys to encrypt your dat a. Only the key you select in the “Default key” will take ef fect. Key 1 – Key 4 – The WEP keys are used to encry pt dat a transmitted within the wireless network. Fill the text box by following the rules below . 64-bit WEP: input 10-digit Hex values (i n the "A-F" ...

  • Edimax PS-1206MF - page 53

    42 WP A-PSK Mode: “WP A-PSK” requires users to select the advanced encryption methods, (i.e. TKIP or AES) and enter a set of keys. TKIP – TKIP (T emporal Key Integrity Protoc ol) changes the temporal key every 10,000 packet s. This insures much gr eater security than the st andard WEP security . AES – AES has been developed to ensure the hi ...

  • Edimax PS-1206MF - page 54

    43 WP A2-PSK Mode Security Mode: TKIP – TKIP (T emporal Key Integrity Protoc ol) changes the temporal key every 10,000 packet s. This insures much gr eater security than the st andard WEP security . Pre-shared Key Format – Select the type of pre-s hared key , you can select Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 ...

  • Edimax PS-1206MF - page 55

    44 6.4.3 TCP/IP Y ou can configure the MFP Server to automatically get an IP address from DHCP server or manually specify a st atic IP . If you need the MFP Server to automatic ally get an IP address from a DHCP server , select “Enable Obtain TCP/IP Settings Automatically (Use DHCP/ BOOTP)”. Y ou also can select “Disable Use the following TCP ...

  • Edimax PS-1206MF - page 56

    45 6.4.4 Save Settings After configuring the MFP Server , you have to click “Save Settings” to save the settings and restart the system. ...

  • Edimax PS-1206MF - page 57

    46 6.5 System T ools 6.5.1 Load Default Y ou can use this page to restore t he factory default settings. All of your previous setting will be cleared. ...

  • Edimax PS-1206MF - page 58

    47 6.5.2 Upgrade Firmware Y ou can upgrade new firmware for this MFP Server in this page. Click “Browse” to select the new firmware, and then click “OK”. The firmware will be updated in several minutes. Be aware that if you have started upgr ading firmware, you hav e to follow all the upgrading steps or the MFP Server can’ t return to nor ...

  • Edimax PS-1206MF - page 59

    48 7. Troubleshooting 1. The MFP Server is not found even after searching with the “MFP Manager”.  Check if the power adapter and the network cable are connected to the MFP Server properly .  Check if the LAN and Ready LEDs are turned on.  Check if the IP Address of the MF P Server is in the some network segment as your computer . - If ...

  • Edimax PS-1206MF - page 60

    49 4. I can’t use the all-in-one printer to sc an, print, use the card reader , or fax a file even I have followed the instructions in the manual.  Attach the all-in-one printer to a PC directly and make sure it is operating correctly . 5. My computer has installed a firewall, and the MFP Server can’t work normally .  Some firewalls, for ...

  • Edimax PS-1206MF - page 61

    50 ...

Manufacturer Edimax Category Server

Documents that we receive from a manufacturer of a Edimax PS-1206MF can be divided into several groups. They are, among others:
- Edimax technical drawings
- PS-1206MF manuals
- Edimax product data sheets
- information booklets
- or energy labels Edimax PS-1206MF
All of them are important, but the most important information from the point of view of use of the device are in the user manual Edimax PS-1206MF.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Edimax PS-1206MF, service manual, brief instructions and user manuals Edimax PS-1206MF. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Edimax PS-1206MF.

Similar manuals

A complete manual for the device Edimax PS-1206MF, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Edimax PS-1206MF by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Edimax PS-1206MF.

A complete Edimax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Edimax PS-1206MF - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Edimax PS-1206MF, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Edimax PS-1206MF, that we can find in the current document
3. Tips how to use the basic functions of the device Edimax PS-1206MF - which should help us in our first steps of using Edimax PS-1206MF
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Edimax PS-1206MF
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Edimax PS-1206MF in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Edimax PS-1206MF?

Use the form below

If you did not solve your problem by using a manual Edimax PS-1206MF, ask a question using the form below. If a user had a similar problem with Edimax PS-1206MF it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)