English dropdown-ico

Manual KTI Networks KSD-103-B Series

20 pages 1.93 mb
Download

Go to site of 20

Summary
  • KTI Networks KSD-103-B Series - page 1

    Industrial 3-Port Fast Ethernet Media Converter Switches KSD-103-A series KSD-103-B series Installation Guide 1/20 DOC.081111 ...

  • KTI Networks KSD-103-B Series - page 2

    (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation m ay be reproduced in any form or by any mean s or used to make any di rective work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time ...

  • KTI Networks KSD-103-B Series - page 3

    3/20 The information contained in this docu ment is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Ru les. Operation is subject to the following two conditions: (1) This device may not cause harmful i ...

  • KTI Networks KSD-103-B Series - page 4

    4/20 Table of Contents 1. Introduction ............................................................................................................................... .5 1.1 Features ................................................................................................................. 6 1.2 Product Panels ................................ ...

  • KTI Networks KSD-103-B Series - page 5

    1. Introduction The industrial rated KSD-103 Fast Ethernet switch series supports three switching-base segment communications and benefit the following appli cations and m ake fiber deployment easier :  Copper to fiber bridging converter  Multimode fiber to single mode fiber bridging converter  Fiber cable extender  Cascaded fiber netwo ...

  • KTI Networks KSD-103-B Series - page 6

     High and wide operating Temperature  Power input interface: Industrial screw termin al block and DC power jack for external commercial power adapter as option  Screw panel and DIN rail mounting support for industrial enclosure  Industrial-rated Emission and Imm unity performance 1.1 Features  Provide 3 switching-base network segment ...

  • KTI Networks KSD-103-B Series - page 7

    KSD-103-B 1.3 Specifications Copper Ports Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 jacks Pin assignments Auto MDI/MDI-X detection Configuration Auto-negotiation Transmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network cable Cat.5 UTP up to 100 meters Fiber Ports Connectors ST, SC, VF-45, Bi-D ...

  • KTI Networks KSD-103-B Series - page 8

    8/20 Forwarding & filtering Non-blocking, full wire speed Switching technology Store and forward Maximum packet length 1536 bytes max. Flow control IEEE 802.3x pause frame base for full duplex operation Back pressure for half duplex operation Broadcast Storm Protection design DC Power Interface Interface Screw-type terminal block 1. Two pairs f ...

  • KTI Networks KSD-103-B Series - page 9

    9/20 Certificate FCC Part 15 Class B CE/EMC EMI EN50081-1 Class B EMS EN55024 CE/LVD Safety EN 60950 EN 50081-1/1992 : EN55022:1994/A1:1995/A2:1997 EN61000-3-2:2000 EN61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001 IEC 61000-4-2:1995 ESD Test IEC 61000-4-3:1995 RS Test IEC 61000-4-4:1995 EFT/BURST Test IEC 61000-4-5:1995 Surge Test IEC 61000-4-6:1996 ...

  • KTI Networks KSD-103-B Series - page 10

    10/20 2. Installation 2.1 Unpacking Check that the following components have been included:  Information CD  The device unit  DIN-rail mounting bracket If any item is found missing or damaged, please contact your local reseller for replacement. The following are available optional accessories:  Panel Mounting Bracket The bracket is used ...

  • KTI Networks KSD-103-B Series - page 11

    label. If you are not sure of the type of power source required, consult your service provider or local power company. 2.3 DIN-Rail Mounting In the product package, a DIN-rail bracket is in stalled on the d evice for mounting the de vice in a industrial DIN-rail enclosure. The steps to mount the device onto a DIN rail are: 1. Install the mounting b ...

  • KTI Networks KSD-103-B Series - page 12

    The final mechanical dimensions after installing DIN rail m ounting bracket are: 2.4 Panel Mounting The product is provided with an optiona l bracket for panel mounting. The bracket supports m ounting the device on a plane surface securely. The mounting steps are: 1. Install the mounting bracket on the device unit. Screw the bracket on the device u ...

  • KTI Networks KSD-103-B Series - page 13

    2.5 Applying Power The power specifications of the device are: Operating Voltage +7 ~ +50VDC Power Consumption 4W max. @+50VDC Using Terminal Blocks Either DC1 interface or DC2 interface can be used to receive DC power from an external power system. Or, DC2 also can be used to deliver the power re ceived on DC1 to next device in cascading way. DC1 ...

  • KTI Networks KSD-103-B Series - page 14

    If cascading the power to next device is needed, install the power wires and plug for another switch. Then, use DC2 contacts. Note: Only up to four device units can be casc aded to receive power from one main power input source. Using DC Power Jack DC Jack Connector: D 6.3mm D 2.0mm AC Power Adapters: Optional power adapters are available for purch ...

  • KTI Networks KSD-103-B Series - page 15

    Use the provided 2P terminal plug for signal wiring and plug into the PF+/- contacts. Normal PF+ and PF- contacts shorted Relay Output Indication Alarm PF+ and PF- contacts open Alarm Events:  Input power failure  Specific fiber port link down (To specify the fiber ports, use the DIP SW located on bottom.) KSD-103-A ON Enable broadcast storm ...

  • KTI Networks KSD-103-B Series - page 16

    3. Making LAN Connections 3.1 Making Copper Port (RJ-45) Connections The copper ports support the following connection types and distances: Network Cables 10BASE-T: 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm 100BASE-TX: 2-pair / 4-pair U TP Cat. 5, EIA/TIA-568B 100-ohm Link distance: Up to 100 meters Auto MDI/MDI-X Function This function allows t ...

  • KTI Networks KSD-103-B Series - page 17

    3.3 LED Indication KSD-103-A KSD-103-B LED Function State Interpretation PWR Power status ON The power is supplied to the device. OFF The power is not supplied to the device. UTPx Copper port link status ON Port link is established. (No traffic) BLINK Port link is up and there is traffic. OFF Port link is down. FXx Fiber port link status ON Port li ...

  • KTI Networks KSD-103-B Series - page 18

    4. Applications 4.1 Application in Industrial Networks The following figure illustrates an application example in an industrial network. Four devices are cascaded by fiber cables. 4.2 Copper to Fiber Bridging Media Converter Application 4.3 Bridging Multimode to Single Mode Fiber Converter Application 18/20 ...

  • KTI Networks KSD-103-B Series - page 19

    19/20 5. Appendix 5.1 Model Definition KSD-103-A Model Ext. FX Connector Cable Re f. Distance Operating Temperature -T Duplex ST MMF 2km -10 ~ 70 o C -C Duplex SC MMF 2km -10 ~ 70 o C -C1 Duplex SC MMF 2km -20 ~ 70 o C -SA2 Duplex SC SMF 20km -20 ~ 70 o C -SL2 Duplex SC SMF 20km -20 ~ 70 o C -SL3 Duplex SC SMF 30km -20 ~ 70 o C -SL4 Duplex SC SMF 4 ...

  • KTI Networks KSD-103-B Series - page 20

    20/20 5.2 Optical Specifications KSD-103-A Model Ext. FX Port Wavelength TX Power Sensitivity RX Max. Power -T FX 1310nm -19 ~ -14dBm -31dBm -14dBm -C FX 1310nm -19 ~ -14dBm -31dBm -14dBm -C1 FX 1310nm -20 ~ -14dBm -31dBm 0dBm -SA2 FX 1310nm -15 ~ -8dBm -31dBm -7dBm -SL2 FX 1310nm -15 ~ -8dBm -30dBm 0dBm -SL3 FX 1310nm -15 ~ -8dBm -34dBm 0dBm -SL4 ...

Manufacturer KTI Networks Category Switch

Documents that we receive from a manufacturer of a KTI Networks KSD-103-B Series can be divided into several groups. They are, among others:
- KTI Networks technical drawings
- KSD-103-B Series manuals
- KTI Networks product data sheets
- information booklets
- or energy labels KTI Networks KSD-103-B Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual KTI Networks KSD-103-B Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KTI Networks KSD-103-B Series, service manual, brief instructions and user manuals KTI Networks KSD-103-B Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KTI Networks KSD-103-B Series.

Similar manuals

A complete manual for the device KTI Networks KSD-103-B Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KTI Networks KSD-103-B Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KTI Networks KSD-103-B Series.

A complete KTI Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KTI Networks KSD-103-B Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KTI Networks KSD-103-B Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KTI Networks KSD-103-B Series, that we can find in the current document
3. Tips how to use the basic functions of the device KTI Networks KSD-103-B Series - which should help us in our first steps of using KTI Networks KSD-103-B Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KTI Networks KSD-103-B Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KTI Networks KSD-103-B Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KTI Networks KSD-103-B Series?

Use the form below

If you did not solve your problem by using a manual KTI Networks KSD-103-B Series, ask a question using the form below. If a user had a similar problem with KTI Networks KSD-103-B Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)