English dropdown-ico

Manual Troy-Bilt 12210

32 pages 1.15 mb
Download

Go to site of 32

Summary
  • Troy-Bilt 12210 - page 1

    Models 12227 – 3.75 HP TUFFY ® 12209 – 5.5 HP BRONCO TM 12210 – 6.5 HP Super BRONCO TM OWNER’S MANUAL Rear -T ine T illers • Safety • Assembly • Controls • Operation • Maintenance • Parts List $ 4.50 GARDEN WAY INCORPORATED SAFETY FIRST! Before operating this equipment, read this Owner's Manual and the separate manual supp ...

  • Troy-Bilt 12210 - page 2

    2 T able of Contents SECTION 1: SAFETY ........................................... 3 Safety Decals ............................................................. 5 Operating Symbols ..................................................... 5 SECTION 2: ASSEMBLY ....................................... 6 Attach Handlebar .................................. ...

  • Troy-Bilt 12210 - page 3

    Safety 1 3 T raining 1. Carefully read this Owner ’ s Manual, the separate Engine Owner ’ s Manual, and any other literature you may receive. Be thor- oughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the tiller. Nev ...

  • Troy-Bilt 12210 - page 4

    4 Section 1: Safety 4 . Exercise caution to avoid slipping or falling. 5 . If the unit should start to vibrate abnor- mally, stop the engine, disconnect the spark plug wire and prevent it from touching the spark plug, and check imme- diately for the cause. Vibration is gener- ally a warning of trouble. 6 . Stop the engine, disconnect the spark plug ...

  • Troy-Bilt 12210 - page 5

    Section 1: Safety 5 Decals For your safety and the safety of others, various safety and opera- tional decals are located on your unit (see Figure 1-2). Keep the decals clean and legible at all times. Contact your local ser- vice dealer or the factory for replacements if any decals are damaged or missing. Refer to the Parts List pages in this Manual ...

  • Troy-Bilt 12210 - page 6

    Assembly 2 Section 6 INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. NOTE: Various tiller models are presented in this Manual. Use only the information appropriate for your tiller model. INSPECT UNIT Inspect the unit ...

  • Troy-Bilt 12210 - page 7

    Section 2: Assembly 7 2. Remove the hairpin cotter (L, Fig. 2-3) and wheel drive pin (M) from the wheel hub (O) and wheel shaft (N). 3. Slide the wheel fully inward on the wheel shaft (N, Fig. 2-3). Reinstall the wheel drive pin (M) through the wheel shaft only (not through the wheel hub). Secure the wheel drive pin with the hairpin cotter (L), pus ...

  • Troy-Bilt 12210 - page 8

    8 Section 2: Assembly 4. Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V). 5. Thread the screw (V) into the cable adjuster (X). 6. Hook the cable spring (W, Fig. 2-6) into the V-shaped bend in the Forward Clutch Bail (Y). 7. Check for correct tension on the for- ward drive belt by taking two measure- ments of the cable spring, as ...

  • Troy-Bilt 12210 - page 9

    Section 2: Assembly 9 STEP 6: CHECK LEVEL OF TRANSMISSION GEAR OIL The transmission was filled with gear oil at the factory. However, you should check the gear oil level at this time to make cer- tain it is correct. IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmis- sion compone ...

  • Troy-Bilt 12210 - page 10

    Features and Controls 3 Section 10 INTRODUCTION This Section describes the location and function of the controls on your tiller. Refer to the following Section, Operation for detailed operating instructions. Practice using these controls, with the engine shut off, until you understand the operation of the controls and feel confi- dent with each of ...

  • Troy-Bilt 12210 - page 11

    Section 3: Features and Controls 11 FORWARD CLUTCH BAIL The Forward Clutch Bail (E, Figure 3-4) controls the engagement of forward drive to the wheels and tines. To operate the Forward Clutch Bail: 1. Put wheels in WHEEL DRIVE position (see “ WARNING ” statement above). 2. Lift and hold the clutch bail (E, Figure 3-4) against the handlebar to s ...

  • Troy-Bilt 12210 - page 12

    Operation 4 Section 12 INTRODUCTION Read this Operation Section and the sepa- rate Engine Owner ’ s Manual before you start the engine. Then, take the time to familiarize yourself with the basic opera- tion of the tiller before using it in the garden. Find an open, level area and prac- tice using the tiller controls without the tines engaging the ...

  • Troy-Bilt 12210 - page 13

    Section 4: Operation 13 Stopping the Engine and Tiller 1. To stop the wheels and tines, release the Forward Clutch Bail (all models) or the Reverse Clutch Control (Models 12209 and 12210) – whichever control is in use. 2. To stop the engine, put the ignition switch and/or the throttle control lever in the “ OFF ” or “ STOP ” position. OPE ...

  • Troy-Bilt 12210 - page 14

    14 Section 4: Operation Preparing Seedbeds Fig. 4-6 Fig. 4-7 • If the garden size will not permit lengthwise and then crosswise tilling, then overlap the first passes by one-half a tiller width, followed by successive passes at one- quarter width (see Fig. 4-8). With planning, you can allow enough room between rows to cultivate (see Fig. 4-9). Le ...

  • Troy-Bilt 12210 - page 15

    Section 4: Operation 15 TILLING TIPS & TECHNIQUES (cont.) Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutri- ents to the soil. The first place t ...

  • Troy-Bilt 12210 - page 16

    16 Section 4: Operation The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled. Follow these procedures to help avoid tangling and to clean the tines, if necessary. • To reduce tangling, set the depth regulator deep enough to ge ...

  • Troy-Bilt 12210 - page 17

    Maintenance 5 Section 17 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or prop- erty da ...

  • Troy-Bilt 12210 - page 18

    18 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. WARNING 4. The gear oil level is correct ...

  • Troy-Bilt 12210 - page 19

    Section 5: Maintenance 19 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. WARNING CHECKING AND ADJUSTING FORWARD DR ...

  • Troy-Bilt 12210 - page 20

    20 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. WARNING FORWARD CLUTCH BAIL ADJUSTMENT If ...

  • Troy-Bilt 12210 - page 21

    Section 5: Maintenance 21 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. WARNING 3. Clean around the oil dipstick ...

  • Troy-Bilt 12210 - page 22

    22 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. WARNING TROUBLESHOOTING Before performing ...

  • Troy-Bilt 12210 - page 23

    Parts List 23 Models 12209, 12210 and 12227 DRA WING NO. 1 1 9552 Hex Hd. Flange Screw, Self-Tapping, 1/4-20 x 1/2 ................................... 2 3 1917536 Decal, Hood ....................................... 1 5 1904572 Tine Hood (Incl. tine flap and Ref. 3) (A) ....................................... 1 1917594 Tine Hood (Incl. tine flap and ...

  • Troy-Bilt 12210 - page 24

    24 Parts List Models 12209, 12210 and 12227 DRA WING NO. 2 ...

  • Troy-Bilt 12210 - page 25

    Parts List 25 Models 12209, 12210 and 12227 P ARTS LIST - DRA WING NO. 2 REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 55104 Upper Handlebar (Incl. Ref. 2) (A) ....... 1 1916996 Upper Handlebar (Incl. Refs. 2 & 28) (B)(C) ........................................ 1 2 1916928 Decal, Forward Clutch Bail .................. ...

  • Troy-Bilt 12210 - page 26

    26 Parts List Models 12209, 12210 and 12227 DRA WING NO. 4 REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 9512 Retainer, Snap Ring, “ E ” Type ........... 2 2 9511 Retainer, Snap Ring .......................... 4 3 1166-1 Shim, 0.062" thick ............................. A/R 1166-2 Shim, 0.030" thick .......... ...

  • Troy-Bilt 12210 - page 27

    Parts List 27 Models 12209, 12210 and 12227 DRA WING NO. 5 1 9727 Plug, Transmission Oil Fill .................. 1 2 1186328 Hex Hd. Flange Screw, 5/16-18 x 5/8, Grade 5 .......................................... 8 5 1916641001 Front Cover, Transmission .................. 1 5A 50074 Rear Cover, Transmission ................... 1 6 50032 Gasket, Hou ...

  • Troy-Bilt 12210 - page 28

    28 Parts List Models 12209, 12210 and 12227 33 44 11 45 13 30 46 47 4 15 37 40 38 39 24 24 43 10 26 29 12 25 21 36 15, 47 30 28 24 22 17 27 32 34 34 16 18 3 8 7 7 23 31 9 20 35 3 15 24 41 42 2 5 6 7 3 3 3 3 24 14 19 41 4 17 1 Forward Clutch Cable Reverse Clutch Cable DRA WING NO. 6 ...

  • Troy-Bilt 12210 - page 29

    Parts List 29 Models 12209, 12210 and 12227 1 * Engine, Recoil Start ............................. 1 2 1917326001 Bracket, Belt Cover.............................. 1 3 1100242 Lock Washer, 5/16 (A) ........................ 8 Lock Washer, 5/16 (B) (C) ................... 9 4 1111696 Hex Hd. Screw, 5/16-24 x 1/2 (A) ....... 2 Hex Hd. Screw, 5/16-24 x ...

  • Troy-Bilt 12210 - page 30

    30 Parts List Models 12209, 12210 and 12227 DRA WING NO. 7 RIGHT SIDE LEFT SIDE Left Hand Tine Right Hand Tine Hold Tine With Blunt End Toward You NOTE: Identify Left and Right sides of tiller by standing in operator position and facing direction of forward travel. 7, 8 ...

  • Troy-Bilt 12210 - page 31

    Parts List 31 Models 12209, 12210 and 12227 1 9711 Hex Hd. Screw, 3/8-16 x 1, Grade 5 ...... 16 2 50049-01 Bolo Tine - Right Hand. Single tine used on left side of tiller. (Incl. two each Refs. 1 & 3) ....................................... 8 3 1733398 Hex Lock Nut, 3/8-16 ............................ 18 4 9555 Hex Hd. Screw, 3/8-16 x 1-3/4 ... ...

  • Troy-Bilt 12210 - page 32

    1905557 (9/00) Printed in U.S.A. © 2000 Garden Way Incorporated CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and informational bulletins. Warranty Service The war ...

Manufacturer Troy-Bilt Category Tiller

Documents that we receive from a manufacturer of a Troy-Bilt 12210 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- 12210 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt 12210
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt 12210.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt 12210, service manual, brief instructions and user manuals Troy-Bilt 12210. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt 12210.

Similar manuals

A complete manual for the device Troy-Bilt 12210, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt 12210 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt 12210.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt 12210 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt 12210, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt 12210, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt 12210 - which should help us in our first steps of using Troy-Bilt 12210
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt 12210
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt 12210 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt 12210?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt 12210, ask a question using the form below. If a user had a similar problem with Troy-Bilt 12210 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)