-
Porter-Cable 352VS - page 1
BEL T SANDER Part No. 899748 - 04-21-03 ESP AÑOL: PÁGINA 15 FRANÇAISE : P AGE 31 Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ ...
-
Porter-Cable 352VS - page 2
2 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are: ● ● lead from lead-based paints ● ● crystalline silica from bricks and cement and other maso ...
-
Porter-Cable 352VS - page 3
3 2 2 . Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 3. Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to ca ...
-
Porter-Cable 352VS - page 4
4 5 . Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6 . Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. 7. Check for misalignment or binding of moving part ...
-
Porter-Cable 352VS - page 5
5 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts µ F ........................ microfarads l ........................ liters kg ........................ kilograms N/cm 2 ........................ newtons per ...
-
Porter-Cable 352VS - page 6
6 4. WORK IN ONE ROOM AT A TIME. Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths. 5. CHILDREN, PREGNANT, OR POTENTIALLY PREGNANT women and nursing mothers should not be present in the work area until the work is done and ...
-
Porter-Cable 352VS - page 7
7 If an extension cord is to be used outdoors it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use. RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS FOREWORD The Porter-Cable Variable Speed Belt Sander (Model 352VS) is designed for re ...
-
Porter-Cable 352VS - page 8
NOTE: Some sanding belts are bi-directional. These belts will not have arrows printed on them. They can be installed to run in either direction. 5. Engage the front pulley by pushing the lever (A) Fig. 1 back to its original position. TO ST ART AND STOP THE BEL T SANDER 1. Be certain that the the switch is off and the power circuit voltage is the s ...
-
Porter-Cable 352VS - page 9
9 4 . Release the trigger to stop the motor. Allow the tool to come to a COMPLETE STOP before turning it over and putting it down. A TT ACHING AND CARE OF DUST BAG Attach the dust bag to the sander by pushing the dust bag tube into the sander vacuum housing (Fig. 4). For the most efficient operation, empty the dust bag when it is approximately half ...
-
Porter-Cable 352VS - page 10
10 9 5. Work back and forth over a fairly wide area to obtain an even surface. 6. Do not let the tool tilt. The edge of the belt can make a deep cuts into the surface. 7. Do not pause in any one spot during the sanding operation. The belt will eat into the work and make the surface uneven. 8. Lift the tool from the work before turning the motor off ...
-
Porter-Cable 352VS - page 11
11 DOORS AND MILL WORK When sanding doors, cabinet frames, sash, storm windows and screens, take care to avoid working into the cross grain where one member meets another. Notice that the right edge of the belt is visible on the sander. Work carefully along the edge where the rail meets the stile. If the joint is slightly uneven, use a fine abrasiv ...
-
Porter-Cable 352VS - page 12
12 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail to start, ch ...
-
Porter-Cable 352VS - page 13
13 ACCESSORIES A complete line of accessories is available from your Porter-Cable · Delta Supplier, Porter-Cable · Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter- ...
-
Porter-Cable 352VS - page 14
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...
-
Porter-Cable 352VS - page 15
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...
Do you have a question concerning Porter-Cable 352VS?
Use the form below
If you did not solve your problem by using a manual Porter-Cable 352VS, ask a question using the form below. If a user had a similar problem with Porter-Cable 352VS it is likely that he will want to share the way to solve it.