-
Harbor Freight Tools 95630 - page 1
COMPRESSOR AND AIR BRUSH KIT Model 95630 SET UP AND OPERA TING INSTRUCTIONS Visit our website at: http://www .harborfreight.com Read and understand tool labels and manual. Failure to follow warnings could result in DEA TH or SERIOUS INJUR Y . SA VE THIS MANUAL. Copyright © 2010 by Harbor Freight T ools ® . All rights reserved. No portion of this ...
-
Harbor Freight Tools 95630 - page 2
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 95630 SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if prod ...
-
Harbor Freight Tools 95630 - page 3
Page 3 For technical questions, please call 1‑800‑444‑3353. SKU 95630 General a. T o reduce the risks of electric shock, re, and injury to persons, read all the instructions before using the tool. W ork area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, re, and injur ...
-
Harbor Freight Tools 95630 - page 4
Page 4 For technical questions, please call 1‑800‑444‑3353. SKU 95630 e. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. f. Always wear eye protection. Wear ANSI-approved safety goggles with side shields. g. Always wear hearing protecti ...
-
Harbor Freight Tools 95630 - page 5
Page 5 For technical questions, please call 1‑800‑444‑3353. SKU 95630 SPECIFIC SAFETY S 1. Maintain labels and nameplates on the tool. These carry important information. If unreadable or missing, contact Harbor Freight T ools for a replacement. 2. DANGER! This Air Compressor is NOT equipped and should not be used “as is” to supply breathi ...
-
Harbor Freight Tools 95630 - page 6
Page 6 For technical questions, please call 1‑800‑444‑3353. SKU 95630 ground fault interrupt (GFCI) system is also a good precaution. This inexpensive device is a good safety measure because it prevents a sustained electrical shock. • Properly maintain and inspect all tools before use to avoid electrical shock 16. Never leave the tool unatt ...
-
Harbor Freight Tools 95630 - page 7
Page 7 For technical questions, please call 1‑800‑444‑3353. SKU 95630 If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user , reducing the risk of electric shock. (See 3‑Prong Plug and Outlet.) 2. The grounding prong in the plug is connected through the gr ...
-
Harbor Freight Tools 95630 - page 8
Page 8 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ V olts Alternating Current A Amperes n 0 xxxx/min. No Load Revolutions per Minute (RPM) W ARNING marking concerning Risk of Eye Injury . Wear ANSI-approved safety goggles with side ...
-
Harbor Freight Tools 95630 - page 9
Page 9 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Assembly Read the ENTIRE IMPORT ANT SAFETY INFORMA TION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are fou ...
-
Harbor Freight Tools 95630 - page 10
Page 10 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Lever (10A)) and the uid will atomize. Continue to move the Finger Lever (10A) to achieve the air volume you need for your spray technique. 7. Continue to adjust the spray volume by using the Finger Lever (10A), moving it front to back. When you have the correct spray v ...
-
Harbor Freight Tools 95630 - page 11
Page 1 1 For technical questions, please call 1‑800‑444‑3353. SKU 95630 clean and wipe down Airbrush and all that were used during operation. 3. AFTER EVER Y 500 HOURS OF REGULAR USE , replace Compression Ring and Inlet and Outlet V alves. Please note: This work should only be done by a qualied service technician. Problem Possible Causes L ...
-
Harbor Freight Tools 95630 - page 12
Page 12 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Compressor Parts List and Assembly Diagram Part Description Qty 1 Screw 8 2 Rear cover 1 4 Rear Body 1 5 Screw 4 6 Stationary Motor 1 7 Bearing 2 8 Rotary Motor 1 9 Front Body 1 10 Counterweight 1 11 Manometer 1 12 Bearing 1 13 Retainer Ring 1 14 Compression Ring 1 17 Cyli ...
-
Harbor Freight Tools 95630 - page 13
Page 13 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Air Brush Parts List and Assembly Diagram Part Description Qty 1A Protective Cap 1 2A Air Cap 1 3A Nozzle 1 4A Air Cap Body 1 5A O-Ring 1 6A Packing 1 7A Packing Nut 1 8A Air Brush Housing 1 9A Needle Adjustment Screw 1 10A Finger Lever 1 11 A Rocker 1 12A Needle Adjusting ...
-
Harbor Freight Tools 95630 - page 14
Page 14 For technical questions, please call 1‑800‑444‑3353. SKU 95630 Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purch ...
Do you have a question concerning Harbor Freight Tools 95630?
Use the form below
If you did not solve your problem by using a manual Harbor Freight Tools 95630, ask a question using the form below. If a user had a similar problem with Harbor Freight Tools 95630 it is likely that he will want to share the way to solve it.