Manual Dixon ZTR 5502

72 pages 0.86 mb
Download

Go to site of 72

Summary
  • Dixon ZTR 5502 - page 1

    ...

  • Dixon ZTR 5502 - page 2

    IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator's manua l carefully and become completely familiar with the controls. The information in this operat ...

  • Dixon ZTR 5502 - page 3

    Part No. 8965 September 1995 INDEX SAFETY ............................................................ Pages 1 - 6 WARRANTY POL ICY ......................................... Page 7 SPECIFICATIONS .............................................. Page 8 - 10 SEAT ADJUSTMENT ......................................... Page 11 CONTROLS .................... ...

  • Dixon ZTR 5502 - page 4

    SAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystander... TIP - OVER Page 1 ...

  • Dixon ZTR 5502 - page 5

    SAFETY SAFETY SYMBOLS: SAFETY ALERT SYMBOL - When you see this symb ol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a potentially hazardous situation which, ...

  • Dixon ZTR 5502 - page 6

    This cutting mower is capable of amputating hands and feet, and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: * Read, understand, and follow al l instructions in the manual and on the mower before starting. * Only allow responsible adults, who are familiar with the ...

  • Dixon ZTR 5502 - page 7

    SAFETY SLOPE OPERATION: Slopes are a major factor related to loss - of - control and tip - over accidents, 'which can result in severe injury or death. All slopes require extra caution. - . If you cannot back up the slope or if you feel uneasy on it, do not mow it. DO Mow across the slope with your Dixon ZTR - never up or down. Remove obstacle ...

  • Dixon ZTR 5502 - page 8

    SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing acti vity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents. • Keep children out of the mowing area and under the watchful care of another responsible adul ...

  • Dixon ZTR 5502 - page 9

    SAFETY SERVICE: • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke. Never refuel the mower indoors. Never store the mower or fuel container inside a building ...

  • Dixon ZTR 5502 - page 10

    DIXON LIMITED WARRANTY POLICY -- HYDRO - GEAR MODEL S This warranty policy applies to all HydroGear mowers or any 50" model, purchased on or after March 1,1990. WARRANTY: Dixon Warranty term is for a period of one (1) year from date of purchase or 400 hours of use, whichever occurs first. Mowers used for re sidential homeowner applications (us ...

  • Dixon ZTR 5502 - page 11

    SPECIFICATIONS Model ZTR 5422 CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for battery s ervice and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system. SEAT: Designed for operator comfort by use of high density closed cell ...

  • Dixon ZTR 5502 - page 12

    SPECIFICATIONS Model ZTR 5502 CHASSIS: 1 1 GA - rectangular tube BODY: Two piece - made of rotationa l molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system. SEAT: Ergonomically designed for operator comfort by use of high dens ...

  • Dixon ZTR 5502 - page 13

    SPECIFICATIONS Model ZTR 5601 CHASSIS: 11 GA - rectangular tube BODY: Tw o piece - made of rotational molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system. SEAT: Ergonomically designed for operator co mfort by use of high dens ...

  • Dixon ZTR 5502 - page 14

    SEAT ADJUSTMENT INSTRUCTIONS Models ZTR 5422 - ZTR 5502 - ZTR 5601 : 1. Place parking brake in ON position. (Pull brake lev er up) 2. Raise and push seat assembly and upper body rearward. 3. Loosen two front seat adjustment knobs, P/N 3978, and slide seat forward or backward to desired position. ~ 4. Re - tighten front seat adjustment knobs, P/N 39 ...

  • Dixon ZTR 5502 - page 15

    CONTROLS Page 12 ...

  • Dixon ZTR 5502 - page 16

    CONTROLS PARKING BRAKE: The parking brake used on the 5000 Series Models is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. Engage parking brake before starting engine. Do not leave engine running for extended periods of time without the parking brake engaged. Damage to the drive syste ...

  • Dixon ZTR 5502 - page 17

    TO GO FORWARD: From neutral position, gent ly push both drive levers forward. To increase speed, move levers farther forward. TO GO BACKWARD: From neutral position, gently pull both drive levers toward you. TURNING: Turning is controlled by moving one drive lever slightly forward or rearward of the other. To turn left, move left lever rearward of t ...

  • Dixon ZTR 5502 - page 18

    CONTROLS BLADE DRIVE: Located on control panel, on operator's right. To engage the mower blades, lift switch up lightly and push forward. To disengage blades, pull switch backward. Switch is clearly marked "on and off ". CIRCUIT BREAKER: Located on control panel, on operator's right. Protection of the electrical system is by (1) ...

  • Dixon ZTR 5502 - page 19

    OPERATION INSTRUCTIONS The safe and successful operation of the 5000 Series Models will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions. During initi ...

  • Dixon ZTR 5502 - page 20

    OPERATION INSTRUCTIONS PARKING BRAKE SWITCH TEST: With parking brake in the OFF position, engine should not turn over or attempt to start when the key switch is moved to the start position. BLADE DRIVE SWITCH TEST: (5000 Series) a. With elect ric blade drive switch turned ON and parking brake in the ON position, engine should not turn over or attem ...

  • Dixon ZTR 5502 - page 21

    OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Cold Engine 1 . Push choke control lever fully forward. 2. Push throttle control lever to 1/2 setting. 3. Insert ignition key and turn to "Start" position. When engine s tarts, release ignition key. Key will return to "Run" position. 4. Once engine starts to warm up, slowly move chok ...

  • Dixon ZTR 5502 - page 22

    OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Engine has been operated. 1. Move throttle control lever to 1/4 to 1/2 setting. 2. Insert ignition key and turn to "Start" position. When engine starts, release ignition key. Key will retu rn to "Run" position. 3. Move throttle control lever to wide open or maximum setting for actual ...

  • Dixon ZTR 5502 - page 23

    OPERATION INSTRUCTIONS M OWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings. In order to achieve the bes ...

  • Dixon ZTR 5502 - page 24

    OPERATI ON INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1 . Set engine speed control to the wide open or full settin g. 2. Do Not Attempt To Cut Grass When It Is Wet. Wet grass will clog both the underside of t ...

  • Dixon ZTR 5502 - page 25

    OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPING S: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide on page 41. CAUTION Be sure that deflector is properly installed on the discharge chute. 1. Set eng ...

  • Dixon ZTR 5502 - page 26

    OPERATION INSTRUCTIONS DECK ROLLERS: Purpose: The spring loaded deck rollers located at the front corners of the mower deck are designed as an aid to limit turf scalping when mowing on uneven ground. Height: Normal height settings as installed at the factory allows each roller to ride slightly above the turf. This setting should prove ideal under m ...

  • Dixon ZTR 5502 - page 27

    CARE AND MAINTENANCE - 5000 SERIES MODELS This portion of the 5000 Series Models owners manual deals with normal service items which can be performed by the owner. Please remember that if you are in doubt as to the correct service procedures to be followed, these and other service situations can be handled by a Dixon ZTR dealer who is familiar with ...

  • Dixon ZTR 5502 - page 28

    CARE AND MAINTENANCE - 5000 SERIES MODELS CUTTER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1 . Safely raise front of mower. 2. Hold or block blade from turning. CAUTION Wear heavy, thick gl oves when holding onto cutter blade, avoid the sharp edge of the blade. NOTE: Be sure blade is centered on pilot before tightenin ...

  • Dixon ZTR 5502 - page 29

    CARE AND MAINTENANCE - 5000 SERIES MODELS BELT TENSION ENGINE TO MOWER DEC K BELT: Models ZTR 5422 & ZTR 5502 P/N 61 1 1 Model ZTR 5601 P/N 6939 MOWER DECK SERPENTINE BELT: Model ZTR 5422 P/N 6109 Model ZTR 5502 P/N 1300 Model ZTR 5601 P/N 6938 Refer to illustration for adjustment procedure. NOTE: Belt defl ection or movement should be approxim ...

  • Dixon ZTR 5502 - page 30

    CARE AND MAINTENANCE - 5000 SERIES MODELS FUEL SHUT OFF VALVE: A fuel shut off valve is located at the bo ttom rear of each fuel tank. Always turn the valve to the "OFF" position when the mower is stored or not in use. LUBRICATION CHASSIS: Number of grease zerks used: (7) LOCATIONS: (1) each front wheel caster and each front wheel hub (1) ...

  • Dixon ZTR 5502 - page 31

    CARE AND MAINTENANCE - 5000 SERIES MODELS 5000 SERIES REAR WHEELS: The rear wheels of all 5000 Series models are of an "offset" center design to allow "reversed" installation for using snow chains or to gain increased stability when mowing on sloped ground. Slopes are a major f actor related to loss - of - control and tip - over ...

  • Dixon ZTR 5502 - page 32

    CARE AND MAINTENANCE - 5000 SERIES MODELS CAUTION HOT oil may cause burns. Allow engine to cool before draining oil. CHANGING THE ENG INE OIL: 1 . The "snap lock" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve. The fitting of a short piece of hose to the valve will ...

  • Dixon ZTR 5502 - page 33

    CARE AND MAINTENANCE - 5000 SERIES MODELS MOWER DECK INSTALLATION: NOTE: B rake link (P/N 5283) normally used for installation of engine to mower deck drive belt, has been placed in position during assembly of the lift frame at the factory. For shipment purposes, the brake link has been secured with a cotter pin and washer. REMOV E AND DISCARD cott ...

  • Dixon ZTR 5502 - page 34

    CARE AND MAINTENANCE - 5000 SERIES MODELS MOWER DECK LEVELING PROCEDURE: There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower d eck. The adjusters have lock nuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck. Deck should be level or pitched slightly h ...

  • Dixon ZTR 5502 - page 35

    CARE AND MAINTENANCE - 5000 SERIES MODELS Adjustment of the drive system is limited to the a ctual function of the hydrostatic transmissions as outlined below. T - BOX TO HYDROSTAT BELT ADJUSTMENT: Tighten the (2) J - bolts on the T - box mounting plate until each belt has 1/8th to 1/4th of an inch free play or movement at a mid - point between the ...

  • Dixon ZTR 5502 - page 36

    CARE AND MAINTENANCE - 5000 SERIES MODELS PARKING BRAKE CABLE ADJUSTMENT: Position parking brake lever in the off or disengaged position. This will allow the belt idler used on the engine to T - box to swing full y and apply tension to the belt. At this time, check that the cable which pulls the idler to a neutral position has approximately 1 - 1/2 ...

  • Dixon ZTR 5502 - page 37

    CARE AND MAINTENANCE - 5000 SERIES MODELS NEUTRALADJUSTMENT : Swing upper control levers out into the neutral slots. Raise upper body to the fully open position. Start engine and disengage parking brake. Caution should be used when releasing parking brake as mower may tend to creep or move prior to adjustment. If a djustment is required, loosen loc ...

  • Dixon ZTR 5502 - page 38

    CARE AND MAINTENANCE - 5000 SERIES MODELS FORWARD TRAVEL SPEED ADJUSTMENTS: Stop engine, move levers to drive position, lightly push each upper control lever forward until a resistance is felt on the lever. At this time, check that the forward leve r stops on the bottom of each lever are hitting the stop blocks. If adjustment is required, loosen th ...

  • Dixon ZTR 5502 - page 39

    CARE AND MAINTENANCE - 5000 SERIES MODELS PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Electric clutches require periodic Air Gap adjust ments to extend the life of the clutch. Listed below is both an Air Gap adjustment procedure and an Ohms test to check for a faulty coil within the clutch. No replacement parts are available to repair a faulty assembl ...

  • Dixon ZTR 5502 - page 40

    CARE AND MAINTENANCE - 5000 SERIES MODELS HYDROST ATIC TRANSMISSION OIL AND FILTER SERVICE SERVICE INTERVALS: 1. Initial oil and filter service - 50 hours. 2. Every 250 hours thereafter. OIL REQUIREMENTS: Any high quality engine oil with an API classification of SG/CD is recommended. RECOMMENDED OI L WEIGHT: Normal operation temperatures - 20 W 50 ...

  • Dixon ZTR 5502 - page 41

    CARE AND MAINTENANCE - 5000 SERIES MODELS WHEELS AND TIRES: Correct tire pressure is important for correct operation of mower. Model ZTR 5422 Front Tires 11X4X4 Air Pressure 16 - 21 Ibs. Rear Tires 18 X 9.50 X 8 Air Pressure 8 - 14 Ibs. Models ZTR 5502 & ZTR 5601 Front Tires 11X4X5 Air Pressure 16 - 21 Ibs. Rear Tires 20 X 1 0 X 8 Air Pressure ...

  • Dixon ZTR 5502 - page 42

    STANDARD SERVICE PARTS LIST MODEL ZTR 5422: BLADES: Standard: P/N 6236 Hi - Lift: P/N 8688 BELTS: Engine To Mo wer Deck: P/N 61 1 1 Serpentine Belt: P/N 6109 Engine To T - Box: P/N 1714 T - Box To Hydros: P/N 1765 Grass Blower Belt: P/N 4983 MODEL ZTR 5502: BLADES: Standard: P/N 8689 Hi - Lift: P/N 9265 BELTS: Engine To Mower Deck: P/N 61 1 1 Serpe ...

  • Dixon ZTR 5502 - page 43

    STANDARD SERVICE PARTS LIST KOHLER AIR AND OIL FILTER PART NUMBERS: Refer to engine manufacturers manual for recommendations regarding frequency of servic e required for engine oil changes and air filter maintenance. Protect your engine investment, use only original equipment filters. Model ZTR 5422: 16HP Pre - Cleaner Foam Element 45083 - 01 Cartr ...

  • Dixon ZTR 5502 - page 44

    TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any riding mower. Type and conditions of grass, cut height setting, engine RPM and ground spe ed are some of the variables that interact creating differences in cut quality. Examination of one or more of the above will generally produce a quality cut. The ...

  • Dixon ZTR 5502 - page 45

    TROUBLESHOOTING DRIVE SYSTEM: t' - SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Consult your dealer for repair Drive system will not function on either side after changing hydrostatic transmission oil and filter Incorrect oil filter installed on system Hydrostatic transmissions are "air locked", low o ...

  • Dixon ZTR 5502 - page 46

    TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consult your dealer for repair Starter will not turn engine over Dead b attery Charge battery Battery discharge Poor connections on battery Battery water low Wrong battery installed in mower Tighten or replace as ...

  • Dixon ZTR 5502 - page 47

    Page 44 ...

  • Dixon ZTR 5502 - page 48

    Page 45 ...

  • Dixon ZTR 5502 - page 49

    Page 46 ...

  • Dixon ZTR 5502 - page 50

    Page 47 ...

  • Dixon ZTR 5502 - page 51

    Page 48 ...

  • Dixon ZTR 5502 - page 52

    Page 49 ...

  • Dixon ZTR 5502 - page 53

    Page 50 ...

  • Dixon ZTR 5502 - page 54

    Page 51 ...

  • Dixon ZTR 5502 - page 55

    Page 52 ...

  • Dixon ZTR 5502 - page 56

    Page 53 ...

  • Dixon ZTR 5502 - page 57

    Page 54 ...

  • Dixon ZTR 5502 - page 58

    Page 55 ...

  • Dixon ZTR 5502 - page 59

    Page 56 ...

  • Dixon ZTR 5502 - page 60

    Page 57 ...

  • Dixon ZTR 5502 - page 61

    Page 58 ...

  • Dixon ZTR 5502 - page 62

    Page 59 ...

  • Dixon ZTR 5502 - page 63

    Page 60 ...

  • Dixon ZTR 5502 - page 64

    Page 61 ...

  • Dixon ZTR 5502 - page 65

    Page 62 ...

  • Dixon ZTR 5502 - page 66

    DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2OOO FAX 316 251 4117 OWNER INFORM ATION DATE PURCHASED MOWER MODEL NUMBER PURCHASED FROM Name Address MOWER SERIAL NUMBER DM - DATE OIL CHANGED: DATE ENGINE TUNED: ...

  • Dixon ZTR 5502 - page 67

    NOTES ...

  • Dixon ZTR 5502 - page 68

    ...

  • Dixon ZTR 5502 - page 69

    NOTES ...

  • Dixon ZTR 5502 - page 70

    ...

  • Dixon ZTR 5502 - page 71

    NOTES ...

  • Dixon ZTR 5502 - page 72

    WARNI NG: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. ® Dixon and ZTR are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. A BLOUNT C OM PAN Y AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLEKS 673370945 3162512000 FAX 316 2 ...

Manufacturer Dixon Category Lawn Mower

Documents that we receive from a manufacturer of a Dixon ZTR 5502 can be divided into several groups. They are, among others:
- Dixon technical drawings
- ZTR 5502 manuals
- Dixon product data sheets
- information booklets
- or energy labels Dixon ZTR 5502
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dixon ZTR 5502.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dixon ZTR 5502, service manual, brief instructions and user manuals Dixon ZTR 5502. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dixon ZTR 5502.

Similar manuals

A complete manual for the device Dixon ZTR 5502, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dixon ZTR 5502 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dixon ZTR 5502.

A complete Dixon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dixon ZTR 5502 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dixon ZTR 5502, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dixon ZTR 5502, that we can find in the current document
3. Tips how to use the basic functions of the device Dixon ZTR 5502 - which should help us in our first steps of using Dixon ZTR 5502
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dixon ZTR 5502
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dixon ZTR 5502 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dixon ZTR 5502?

Use the form below

If you did not solve your problem by using a manual Dixon ZTR 5502, ask a question using the form below. If a user had a similar problem with Dixon ZTR 5502 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)