English dropdown-ico

Manual Dell 9.8(0.0)

1905 pages 32.47 mb
Download

Go to site of 1905

Summary
  • Dell 9.8(0.0) - page 1

    Dell Networking Command-Line Reference Guide for the Z9500 Switch 9.8(0.0) ...

  • Dell 9.8(0.0) - page 2

    Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 201 ...

  • Dell 9.8(0.0) - page 3

    Contents 1 About this Guide................................................................................................. 45 Objectives ............................................................................................................................................ 45 Audience .......................................................... ...

  • Dell 9.8(0.0) - page 4

    cam-acl ............................................................................................................................................... 92 cam-acl (Configuration) ..................................................................................................................... 94 cam-audit linecard ............................... ...

  • Dell 9.8(0.0) - page 5

    show debugging ................................................................................................................................ 145 show environment ............................................................................................................................ 146 show inventory ......................................... ...

  • Dell 9.8(0.0) - page 6

    dot1x server-timeout ........................................................................................................................ 206 dot1x supplicant-timeout ................................................................................................................. 207 dot1x tx-period ............................................. ...

  • Dell 9.8(0.0) - page 7

    show cam-acl-vlan ..................................................................................................................... 268 show cam-usage ........................................................................................................................ 270 show running config acl-vlan-group ................................... ...

  • Dell 9.8(0.0) - page 8

    set as-path ................................................................................................................................... 319 set automatic-tag ....................................................................................................................... 320 set comm-list delete ....................................... ...

  • Dell 9.8(0.0) - page 9

    show bfd neighbors .......................................................................................................................... 356 vrrp bfd .............................................................................................................................................. 358 8 Border Gateway Protocol....................... ...

  • Dell 9.8(0.0) - page 10

    debug ip bgp notifications .......................................................................................................... 399 debug ip bgp soft-reconfiguration ............................................................................................ 400 debug ip bgp updates ............................................................ ...

  • Dell 9.8(0.0) - page 11

    redistribute ................................................................................................................................... 441 redistribute ospf .......................................................................................................................... 443 router bgp ............................................. ...

  • Dell 9.8(0.0) - page 12

    show ip extcommunity-list ......................................................................................................... 502 show running-config extcommunity-list .................................................................................. 502 IPv6 BGP Commands ....................................................................... ...

  • Dell 9.8(0.0) - page 13

    default-metric ............................................................................................................................. 533 description ................................................................................................................................... 534 distance bgp ............................................ ...

  • Dell 9.8(0.0) - page 14

    show ip bgp paths extcommunity ..............................................................................................566 show ip bgp regexp .................................................................................................................... 566 show ipv6 prefix-list ........................................................... ...

  • Dell 9.8(0.0) - page 15

    show mac protocol-queue-mapping ..............................................................................................602 show protocol-queue-mapping ...................................................................................................... 603 11 Data Center Bridging (DCB)........................................................ ...

  • Dell 9.8(0.0) - page 16

    dcb pfc-total-buffer-size ................................................................................................................. 643 dcb pfc-queues ................................................................................................................................ 644 dcb <ets | pfc> enable ............................. ...

  • Dell 9.8(0.0) - page 17

    debug ip dhcp client packets ..................................................................................................... 706 default-router .............................................................................................................................. 707 disable ............................................................. ...

  • Dell 9.8(0.0) - page 18

    ipv6 helper-address .....................................................................................................................735 show ip dhcp binding ..................................................................................................................736 show ip dhcp snooping ................................................ ...

  • Dell 9.8(0.0) - page 19

    show fip-snooping fcf ....................................................................................................................... 772 show fip-snooping sessions ............................................................................................................. 773 show fip-snooping statistics .................................. ...

  • Dell 9.8(0.0) - page 20

    ip igmp ssm-map ........................................................................................................................ 814 ip igmp static-group ....................................................................................................................815 ip igmp version .................................................... ...

  • Dell 9.8(0.0) - page 21

    show config (from INTERFACE RANGE mode) ......................................................................... 865 show interfaces ........................................................................................................................... 866 show interfaces configured ............................................................. ...

  • Dell 9.8(0.0) - page 22

    22 Internet Protocol Security (IPSec)............................................................... 915 crypto ipsec transform-set ............................................................................................................... 915 crypto ipsec policy .................................................................................. ...

  • Dell 9.8(0.0) - page 23

    ipv4 unicast-host-route .................................................................................................................... 957 load-balance ..................................................................................................................................... 958 management route ..................................... ...

  • Dell 9.8(0.0) - page 24

    ipv6 control-plane icmp error-rate-limit ....................................................................................... 1018 ipv6 flowlabel-zero ......................................................................................................................... 1018 ipv6 host ........................................................... ...

  • Dell 9.8(0.0) - page 25

    debug isis adj-packets .................................................................................................................... 1061 debug isis graceful-restart ..............................................................................................................1062 debug isis local-updates ..................................... ...

  • Dell 9.8(0.0) - page 26

    metric-style ..................................................................................................................................... 1102 multi-topology ................................................................................................................................ 1103 net ............................................. ...

  • Dell 9.8(0.0) - page 27

    show mac-address-table aging-time ....................................................................................... 1151 show mac learning-limit ........................................................................................................... 1152 Virtual LAN (VLAN) Commands .......................................................... ...

  • Dell 9.8(0.0) - page 28

    LLDP-MED Commands ................................................................................................................... 1189 advertise med guest-voice ....................................................................................................... 1190 advertise med guest-voice-signaling ........................................ ...

  • Dell 9.8(0.0) - page 29

    ip msdp sa-limit .............................................................................................................................. 1228 ip msdp shutdown .......................................................................................................................... 1229 ip multicast-msdp ...................................... ...

  • Dell 9.8(0.0) - page 30

    enable inverse-mask ................................................................................................................. 1269 fast-convergence ...................................................................................................................... 1270 flood-2328 ........................................................... ...

  • Dell 9.8(0.0) - page 31

    show ip ospf neighbor ............................................................................................................... 1321 show ip ospf routes ................................................................................................................... 1322 show ip ospf statistics .............................................. ...

  • Dell 9.8(0.0) - page 32

    37 PIM-Sparse Mode (PIM-SM)........................................................................ 1373 IPv4 PIM-Sparse Mode Commands ............................................................................................... 1373 clear ip pim rp-mapping .......................................................................................... ...

  • Dell 9.8(0.0) - page 33

    ipv6 pim spt-threshold .............................................................................................................. 1412 show ipv6 pim bsr-router ......................................................................................................... 1413 show ipv6 pim interface ................................................... ...

  • Dell 9.8(0.0) - page 34

    show vlan private-vlan .................................................................................................................... 1451 switchport mode private-vlan ........................................................................................................ 1454 42 Per-VLAN Spanning Tree Plus (PVST+)............................ ...

  • Dell 9.8(0.0) - page 35

    match mac dot1p ...................................................................................................................... 1496 match mac vlan ......................................................................................................................... 1497 policy-aggregate ................................................... ...

  • Dell 9.8(0.0) - page 36

    distribute-list in ............................................................................................................................... 1539 distribute-list out ............................................................................................................................ 1540 ip poison-reverse .............................. ...

  • Dell 9.8(0.0) - page 37

    hello-time ........................................................................................................................................ 1582 max-age .......................................................................................................................................... 1583 protocol spanning-tree rstp ................. ...

  • Dell 9.8(0.0) - page 38

    timeout login response ............................................................................................................. 1625 username ................................................................................................................................... 1626 RADIUS Commands .................................................. ...

  • Dell 9.8(0.0) - page 39

    ip ssh rekey ............................................................................................................................... 1661 ip ssh rhostsfile .......................................................................................................................... 1662 ip ssh rsa-authentication (Config) ....................... ...

  • Dell 9.8(0.0) - page 40

    show sflow linecard ........................................................................................................................ 1703 50 Simple Network Management Protocol (SNMP) and Syslog............... 1705 SNMP Commands .................................................................................................................. ...

  • Dell 9.8(0.0) - page 41

    show logging auditlog .............................................................................................................. 1748 show logging driverlog ............................................................................................................. 1748 show logging kernellog ................................................... ...

  • Dell 9.8(0.0) - page 42

    ntp multicast client ......................................................................................................................... 1793 ntp master <stratum> ..................................................................................................................... 1794 ntp server ......................................... ...

  • Dell 9.8(0.0) - page 43

    vlan-stack trunk .............................................................................................................................. 1832 tagged port-channel ...................................................................................................................... 1834 untagged port-channel ................................... ...

  • Dell 9.8(0.0) - page 44

    unit-id .............................................................................................................................................. 1871 vlt domain ........................................................................................................................................ 1872 vlt-peer-lag port-channel ............... ...

  • Dell 9.8(0.0) - page 45

    1 About this Guide This book provides information about the Dell Networking OS command line interface (CLI). This book also includes information about the protocols and features found in Dell Networking OS. References For more information about your system, refer to the following documents: • Dell Networking OS Configuration Guides • Installati ...

  • Dell 9.8(0.0) - page 46

    Audience This book is intended for system administrators who are responsible for configuring or maintaining networks. This guide assumes that you are knowledgeable in Layer 2 and Layer 3 networking technologies. Conventions This book uses the following conventions to describe command syntax. Keyword Keywords are in Courier font and must be entered ...

  • Dell 9.8(0.0) - page 47

    2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Command Line When the system boots successfully, you a ...

  • Dell 9.8(0.0) - page 48

    User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) Dell#conf When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is ...

  • Dell 9.8(0.0) - page 49

    radius Interface configuration for RADIUS redirect-list Named redirect-list route Establish static routes scp SCP configuration commands source-route Process packets with source routing header options ssh SSH configuration commands tacacs Interface configuration for TACACS+ telnet Specify telnet options tftp TFTP configuration commands trace-group ...

  • Dell 9.8(0.0) - page 50

    Key Combination Action Esc F Moves the cursor forward one word. Esc D Deletes all the characters from the cursor to the end of the word. Navigating the CLI Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with ...

  • Dell 9.8(0.0) - page 51

    find searches for the first occurrence of a pattern grep displays text that matches a pattern. The grep command option has an ignore-case suboption that makes the search case-insensitive. For example, the commands: show run | grep Ethernet returns a search result with instances containing a capitalized “Ethernet,” such as interface TenGigabitEt ...

  • Dell 9.8(0.0) - page 52

    1. Verify that you are logged in to ROUTER BGP mode. 2. Enter the command address-family 3. Enter the protocol type. • For IPv4, enter ipv4 multicast . The prompt changes to include (conf-router_bgp_af) for IPv4. CLASS-MAP Mode To create or configure a class map, use CLASS-MAP mode. For more information, refer to Policy-Based QoS Commands . To en ...

  • Dell 9.8(0.0) - page 53

    DHCP POOL Mode To create an address pool, use DHCP POOL mode. For more information, refer to Dynamic Host Configuration Protocol (DHCP) . To enter DHCP POOL mode: 1. Verify that you are logged in to DHCP mode. 2. Enter the pool command then the pool name. The prompt changes to include (config-dhcp- pool- name ). You can return to DHCP mode by using ...

  • Dell 9.8(0.0) - page 54

    can access CONFIGURATION mode to configure interfaces, routes and protocols on the switch. While you are logged in to EXEC Privilege mode, the # prompt is displayed. EXTENDED COMMUNITY LIST Mode To enable and configure a BGP extended community, use EXTENDED COMMUNITY LIST mode. To enter EXTENDED COMMUNITY LIST mode: 1. Verify that you are logged in ...

  • Dell 9.8(0.0) - page 55

    Prompt Interface Type Dell(conf-if- nu-0)# Null Interface then zero Dell(conf-if- po-0)# Port-channel interface number Dell(conf-if- vl-0)# VLAN Interface then VLAN number (range 1–4094) Dell(conf-if- ma-0/0)# Management Ethernet interface then slot/port information Dell(conf-if- tu-0)# Tunnel interface then tunnel ID. Dell(conf-if- range)# Desig ...

  • Dell 9.8(0.0) - page 56

    LLDP MANAGEMENT INTERFACE Mode To enable and configure Link Layer Discovery Protocol (LLDP) on management interfaces, use LLDP MANAGEMENT INTERFACE mode. To enter LLDP MANAGEMENT INTERFACE mode: 1. Verify that you are logged in to LLDP mode. 2. Enter the management-interface command. The prompt changes to include (conf-lldp-mgmtIf). LINE Mode To co ...

  • Dell 9.8(0.0) - page 57

    2. Enter the protocol spanning-tree mstp command. The prompt changes to include (conf- mstp). You can return to CONFIGURATION mode by using the exit command. OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter ...

  • Dell 9.8(0.0) - page 58

    PROTOCOL GVRP Mode To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For more information, refer to GARP VLAN Registration (GVRP) . To enter PROTOCOL GVRP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol gvrp command. The prompt changes to include (config-gvrp). You can return ...

  • Dell 9.8(0.0) - page 59

    1. Verify that you are logged in to CONFIGURATION mode. 2. Use the router isis command. The prompt changes to include (conf-router_isis). You can return to CONFIGURATION mode by using the exit command. ROUTER OSPF Mode To configure OSPF, use ROUTER OSPF mode. For more information, refer to Open Shortest Path First (OSPFv2) . To enter ROUTER OSPF mo ...

  • Dell 9.8(0.0) - page 60

    TRACE-LIST Mode To configure a Trace list, use TRACE-LIST mode. To enter TRACE-LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ip trace-list command. Include the name of the Trace list. The prompt changes to include (conf-trace-acl). You can exit this mode by using the exit command. VLT DOMAIN Mode To enable and conf ...

  • Dell 9.8(0.0) - page 61

    3 File Management This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. boot system Specify the location where the Dell Networking OS image used to boot the system is stored. Z9500 Syntax boot system {gateway ip address | {default | primary | secondary} {syste ...

  • Dell 9.8(0.0) - page 62

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. Usage Information To display these changes i ...

  • Dell 9.8(0.0) - page 63

    CAUTION: This command deletes all files, including the startup configuration file. So, after executing this command, consider saving the running config as the startup config (use the write memory command or copy run start command). restore factory-defaults Restore factory defaults. Syntax restore factory-defaults stack-unit {stack—unit—number | ...

  • Dell 9.8(0.0) - page 64

    Usage Information Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fan-out, and so forth). When restoring all units in a stack, all the units in the stack are placed into stand- alone mode. When restoring a single unit in a stack, that unit placed in stand-alone mode. No other units in the ...

  • Dell 9.8(0.0) - page 65

    * Proceed with caution ! * ************************************************************** Proceed with factory settings? Confirm [yes/no]:yes -- Restore status -- Unit Nvram Config ------------------------ 0 Success Success 1 Success Success 2 Success Success 3 Not present 4 Not present 5 Not present Power-cycling the unit(s). Dell# Example (single ...

  • Dell 9.8(0.0) - page 66

    * persistent settings (stacking, fanout, etc.) * * After restoration the unit(s) will be powercycled immediately. * * Proceed with caution ! * ************************************************************** Proceed with factory settings? Confirm [yes/no]:yes -- Restore status -- Unit Nvram Config ------------------------ 1 Success Power-cycling the ...

  • Dell 9.8(0.0) - page 67

    Version Description 9.2(1.0) Introduced on the Z9500. show bootvar Display the variable settings for the boot parameters. Z9500 Syntax show bootvar Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The f ...

  • Dell 9.8(0.0) - page 68

    Related Commands boot system — sets the location of Dell Networking OS image files. show file Display contents of a text file in the local filesystem. Z9500 Syntax show file filesystem Parameters filesystem Enter one of the following: • For internal flash, enter flash: • For USB flash, enter usbflash: Command Modes EXEC Privilege Command Hist ...

  • Dell 9.8(0.0) - page 69

    enable password 7 94849d8482d5c3 ! username test password 7 93e1e7e2ef ! enable restricted 7 948a9d848cd5c3 ! protocol spanning-tree 0 bridge-priority 8192 rapid-root-failover enable ! interface TenGigabitEthernet 0/0 no ip address shutdown Related Commands format flash — Erases all the existing files and reformats the file system in the internal ...

  • Dell 9.8(0.0) - page 70

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example Dell# show os-version RELEASE IMAGE INFORMATION : ------------------------------------- ...

  • Dell 9.8(0.0) - page 71

    show running-config Display the current configuration and display changes from the default values. Z9500 Syntax show running-config [ entity ] [configured] [status] Parameters entity (OPTIONAL) To display that entity’s current (non-default) configuration, enter one of the following keywords: NOTE: If you did not configure anything that entity, no ...

  • Dell 9.8(0.0) - page 72

    hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current interface configuration interface tunnel for all configured tunnels. For a specific tunnel, enter the tunnel ID. The range is from 1 to 16383. ip for the current IP configuration isis for the current ISIS configuration line for the ...

  • Dell 9.8(0.0) - page 73

    qos-policy- input for the current input QoS policy configuration qos-policy- output for the current output QoS policy configuration radius for the current RADIUS configuration redirect- list for the current redirect-list configuration redundancy for the current RPM redundancy configuration resolve for the current DNS configuration rip for the curre ...

  • Dell 9.8(0.0) - page 74

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 75

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 76

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example Dell#show version Dell Force10 Real Time Operating System Software Dell Force10 Operatin ...

  • Dell 9.8(0.0) - page 77

    Lines Beginning With Description Chassis Type: Chassis type (for example, E1200, E600, E600i, E300, C300, C150, S25, S50, S55, S60, S4810) Control Processor:... Control processor information and amount of memory on processor Route Processor 1:... Route processor 1 information and the amount of memory on that processor Route Processor 2:... Route pr ...

  • Dell 9.8(0.0) - page 78

    Parameters bootflash- image Enter the keyword bootflash-image to upgrade the GRUB bootloader image. bootselector- image Enter the keyword bootselector-image to upgrade the BIOS system image. Use this option only with TAC supervision. system all Enter the keywords system all to upgrade the bootflash or bootselector image on all Z9500 CPUs: Control P ...

  • Dell 9.8(0.0) - page 79

    Version Description 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. Usage Information A system message displays with status information about the bootflash upgrade. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility ...

  • Dell 9.8(0.0) - page 80

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introdu ...

  • Dell 9.8(0.0) - page 81

    Related Commands • upgrade fpga-image system fpga booted — upgrades the FPGA devices in all Z9500 CPUs. upgrade fpga-image system cpld booted Use this command to upgrade the CPLD devices in the Z9500 Route Processor and Control Processor CPUs using the currently running Dell Networking operating-system image (and only when required by the upgra ...

  • Dell 9.8(0.0) - page 82

    * automatically rebooted to reload the upgraded components. * ************************************************************ Upgrade CPLD image for system [yes/no]: yes FPGA upgrade in progress!!! Please do NOT power off the unit !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ...

  • Dell 9.8(0.0) - page 83

    --------------------------------------------------------------- --------- CP FPGA 0x14 0x13 *************************************************************** ******** * Warning - Upgrading FPGA is inherently risky and should * * only be attempted when necessary. A failure at this upgrade may * * cause a board RMA. Proceed with caution ! * *********** ...

  • Dell 9.8(0.0) - page 84

    scp: file-url Enter the keyword scp: and specify the location of the image file in the format userid : password @ host-ip / filepath or press Enter to launch a prompt sequence. tftp: file-url Enter the keyword tftp: and specify the location of the image file in the format // host-ip / filepath or press Enter to launch a prompt sequence. flash: file ...

  • Dell 9.8(0.0) - page 85

    Example Dell# upgrade system tftp://10.11.8.12/dv-rainier-13 a: 00:39:32 : Discarded 1 pkts. Expected block num : 51. Received block num: 50 !00:39:36 : Discarded 1 pkts. Expected block num : 65. Received block num: 64 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!! ...

  • Dell 9.8(0.0) - page 86

    Version Description 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information You can enter this command in the following ways: • verify md5 flash :// img-file • verify md5 flash :// img-file < hash-value > • verify sha256 flash :// img-file • verify sha256 flash :// img-file < hash-value > Example Witho ...

  • Dell 9.8(0.0) - page 87

    4 Control and Monitoring This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP). NOTE: This command replaces the enable optic-info-update interval command to update information on temperature and power monitoring in the simple network manageme ...

  • Dell 9.8(0.0) - page 88

    Version Description 8.3.7.0 Introduced on the S4810. Usage Information You must save the configuration and reload the system to implement ASF. When you enter the command, the system sends a message stating that the new mode is enabled when the system reloads. banner exec Configure a message that is displayed when your enter EXEC mode. Z9500 Syntax ...

  • Dell 9.8(0.0) - page 89

    Version Description E-Series Original Command Usage Information After entering the banner exec command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When you connect to the router, if a message of the day banner is configured, it displays first. If no message of the day banner is co ...

  • Dell 9.8(0.0) - page 90

    character (%). Range: maximum of 50 lines, up to 255 characters per line Defaults No banner is configured and the CR is required when creating a banner. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . T ...

  • Dell 9.8(0.0) - page 91

    13d21h10m: %RPM0-P:CP %SEC-5-LOGIN_SUCCESS: Login successful for user on line console This is the banner Dell> Related Commands banner motd — sets a Message of the Day banner. banner motd Set a message of the day (MOTD) banner. Z9500 Syntax banner motd c line c Parameters c Enter a delineator character to specify the limits of the text banner. ...

  • Dell 9.8(0.0) - page 92

    configured, it displays first. If no message of the day banner is configured, the login banner and prompt appear. After the user has logged in, the EXEC banner (if configured) displays. Related Commands banner exec — enables the display of a text string when you enter EXEC mode. banner login — sets a banner to display after successful login to ...

  • Dell 9.8(0.0) - page 93

    l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number [vman- qos | vman- dual-qos] number ecfmacl number {openflow {4| 8}} Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor ...

  • Dell 9.8(0.0) - page 94

    When configuring space for IPv6 ACLs, the total number of Blocks must equal 13. Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10). If you enabled BMP 3.0, to perform a reload on the chassis to upgrade any configuration changes that have c ...

  • Dell 9.8(0.0) - page 95

    l2acl number ipv4acl number ipv6acl number , ipv4qos number l2qos number l2pt number ipmacacl number ecfmacl number [nlbclusteracl number ] [vman-qos | vman-dual-qos number ] ipv4pbr number openflo w {4|8} | fcoe number Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocat ...

  • Dell 9.8(0.0) - page 96

    Usage Information Save the new CAM settings to the startup-config ( write-mem or copy run start ) then reload the system for the new settings to take effect. The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. The ipv4acl profile range is from 1 to 4. When configuring space for I ...

  • Dell 9.8(0.0) - page 97

    Usage Information Enables periodic audits of the software and hardware copies of the IPv4 forwarding table. clear alarms Clear alarms on the system. Z9500 Syntax clear alarms Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command L ...

  • Dell 9.8(0.0) - page 98

    clear line Reset a terminal line. Z9500 Syntax clear line { line-number | console 0 | vty number } Parameters line-number Enter a number for one of the 12 terminal lines on the system. The range is from 0 to 11. console 0 Enter the keywords console 0 to reset the console port. vty number Enter the keyword vty then a number to clear a terminal line. ...

  • Dell 9.8(0.0) - page 99

    Parameters rp Enter the keyword rp to clear the software trace log from the Route Processor CPU. linecard slot-id Enter the linecard slot-id parameters to specify the line-card CPU whose software trace log you want to clear. Defaults Clear the trace log files from all Z9500 CPUs. Command Modes CONFIGURATION Command History Version Description 9.2(1 ...

  • Dell 9.8(0.0) - page 100

    Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example Dell#configure Dell(conf)# debug cpu-traffic-stats Enable the collection of computer processor unit (CPU) traffic statistics. Z9500 Syntax debug ...

  • Dell 9.8(0.0) - page 101

    Usage Information This command enables (and disables) the collection of CPU traffic statistics from the time this command is executed (not from system boot). However, excessive traffic a CPU receives automatically triggers (turn on) the collection of CPU traffic statics. The following message is an indication that collection of CPU traffic is autom ...

  • Dell 9.8(0.0) - page 102

    Version Description E-Series Original command. disable Return to EXEC mode. Z9500 Syntax disable [ level ] Parameters level (OPTIONAL) Enter a number for a privilege level of the Dell Networking OS. The range is from 0 to 15. The default is 1 . Defaults 1 Command Modes EXEC Privilege Command History This guide is platform-specific. For command info ...

  • Dell 9.8(0.0) - page 103

    do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Z9500 Syntax do command Parameters command Enter an EXEC-level command. Defaults none Command Modes • CONFIGURATION • INTERFACE Command History This guide is platform-specific. For command information about other platforms, ref ...

  • Dell 9.8(0.0) - page 104

    Proceed with reload [confirm yes/no]: n Dell(conf-if-te-5/0)# enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Z9500 Syntax enable [ level ] Parameters level (OPTIONAL) Enter a number for a privilege level of Dell Networking OS. The range is from 0 to 15. Defaul ...

  • Dell 9.8(0.0) - page 105

    at a specific privilege level. If no privilege level is specified, the default is privilege level 15 . NOTE: If you are authorized for the EXEC Privilege mode by your role, you do not need to enter an enable password. Related Commands enable password — configures a password for the enable command and to access a privilege level. enable optic-info ...

  • Dell 9.8(0.0) - page 106

    end Return to EXEC Privilege mode from other command modes (for example, CONFIGURATION or ROUTER OSPF modes). Z9500 Syntax end Command Modes • CONFIGURATION • SPANNING TREE • MULTIPLE SPANNING TREE • LINE • INTERFACE • TRACE-LIST • VRRP • ACCESS-LIST • PREFIX-LIST • AS-PATH ACL • COMMUNITY-LIST • ROUTER OSPF • ROUTER RIP ? ...

  • Dell 9.8(0.0) - page 107

    exec-timeout Set a time interval that the system waits for input on a line before disconnecting the session. Z9500 Syntax exec-timeout minutes [ seconds ] To return to default settings, use the no exec-timeout command. Parameters minutes Enter the number of minutes of inactivity on the system before disconnecting the current session. The range is f ...

  • Dell 9.8(0.0) - page 108

    exit Return to the lower command mode. Z9500 Syntax exit Command Modes • EXEC Privilege • CONFIGURATION • LINE, INTERFACE • TRACE-LIST • PROTOCOL GVRP • SPANNING TREE • MULTIPLE SPANNING TREE • MAC ACCESS LIST • ACCESS-LIST • AS-PATH ACL • COMMUNITY-LIST • PREFIX-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER ...

  • Dell 9.8(0.0) - page 109

    ftp-server enable Enable FTP server functions on the system. Z9500 Syntax ftp-server enable Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networki ...

  • Dell 9.8(0.0) - page 110

    Related Commands ftp-server topdir — sets the directory to be used for incoming FTP connections to the E-Series. ftp-server username — sets a username and password for incoming FTP connections to the E-Series. ftp-server topdir Specify the top-level directory to be accessed when an incoming FTP connection request is made. Z9500 Syntax ftp-serve ...

  • Dell 9.8(0.0) - page 111

    Related Commands ftp-server enable — enables FTP server functions on the switch. ftp-server username — sets a username and password for incoming FTP connections. ftp-server username Create a user name and associated password for incoming FTP server sessions. Z9500 Syntax ftp-server username username password [ encryption-type ] password To dele ...

  • Dell 9.8(0.0) - page 112

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. hostname Set the host name of the system. Z9500 Syntax hostname name Parameters name Enter a text string, up to 32 characters long. Defaults Dell Command Modes CONFIGURATION Command Hist ...

  • Dell 9.8(0.0) - page 113

    ip ftp password Specify a password for outgoing FTP connections. Z9500 Syntax ip ftp password [ encryption-type ] password To remove a password and return to the default setting, use the no ip ftp password [ password ] command. Parameters encryption- type (OPTIONAL) Enter one of the following numbers: • 0 (zero) for an unecrypted (clear text) pas ...

  • Dell 9.8(0.0) - page 114

    Related Commands ip ftp username — sets the user name for the FTP sessions. ip ftp source-interface Configure an interface’s IP address as the source IP address for FTP connections. Z9500 Syntax ip ftp source-interface interface To delete an interface, use the no ip ftp source-interface interface command. Parameters interface Enter the followin ...

  • Dell 9.8(0.0) - page 115

    Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. ip ftp username Assign a u ...

  • Dell 9.8(0.0) - page 116

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Configure a password with the ip ftp password command. Related Commands ip ftp password — sets the password for FTP connections. ip http source-interface Configure an interface’s IP address as the source IP ad ...

  • Dell 9.8(0.0) - page 117

    Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S4810, S4820T, S6000, and Z9000. 8.3.11.1 Introduced on the Z9000 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094) 8.1.1.0 Introduced on E-Series ExaScale 7.6.1.0 Support added for S-Series 7.5.1.0 Introduced on C-Series ip telnet server ...

  • Dell 9.8(0.0) - page 118

    Related Commands ip ssh server — enables the secure shell (SSH) server on the system. ip telnet source-interface Set an interface’s IP address as the source address in outgoing packets for Telnet sessions. Z9500 Syntax ip telnet source-interface interface To return to the default setting, use the no ip telnet source-interface [ interface ] comm ...

  • Dell 9.8(0.0) - page 119

    Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command Related Commands telnet — ...

  • Dell 9.8(0.0) - page 120

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 121

    Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the ...

  • Dell 9.8(0.0) - page 122

    clear-line enable Enables you to clear your existing sessions. Defaults Not configured. You can use all the available sessions. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of ...

  • Dell 9.8(0.0) - page 123

    When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of your existing sessions. Close any of your existing sessions to log in to the system. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'. Login: admin Password: Maximu ...

  • Dell 9.8(0.0) - page 124

    Version Description 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000- ON, and Z9500. Usage Information Only the system and security administrators can configure login activity tracking and view the login activity details of other users. If you enable user login statistics, the system displays the last successful login details of the cur ...

  • Dell 9.8(0.0) - page 125

    Related Commands login concurrent-session — Configures the limit of concurrent sessions for all users on console and virtual terminal lines. show login statistics — Displays login statistics of users who have used the console or virtual terminal lines to log in to the system. logging coredump server Configure the switch to move (upload) a core ...

  • Dell 9.8(0.0) - page 126

    The kernel core dump is copied to the Control Processor (CP) core-dump directory: flash://CORE_DUMP_DIR/f10_ cpu _ timestamp .kcore.gz Where cpu specifies a Z9500 CPU and is one of the following values: cp (Control Processor), cp (Route Processor), lp0 (line-card processor 0), lp1 (line-card processor 1), or lp2 (line-card processor 2); timestamp i ...

  • Dell 9.8(0.0) - page 127

    ip-address (OPTIONAL) Enter the IPv4 address of the device to which you are testing connectivity. The address must be in the dotted decimal format. ipv6-address (OPTIONAL) Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros. count Enter the n ...

  • Dell 9.8(0.0) - page 128

    outgoing- interface (IPv6 link-local address) Enter the outgoing interface for ping packets to a destination link-local address. pattern pattern (IPv4 only) Enter the IPv4 data pattern. Range: 0-FFFF. Default: 0xABCD . sweep-min- size Enter the minimum size of datagram in sweep range. The range is from 52 to 15359 bytes. sweep-max- size Enter the m ...

  • Dell 9.8(0.0) - page 129

    Version 8.4.1.0 IPv6 pinging available on management interface. Version 8.3.1.0 Introduced extended ping options. Version 8.2.1.0 Introduced on the E-Series ExaScale (IPv6). Version 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). Version 7.9.1.0 Introduced VRF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Seri ...

  • Dell 9.8(0.0) - page 130

    Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms) Dell# reload Reboot the system. Z9500 Syntax reload [conditional nvram-cfg-change ] Parameters conditional nvram-cfg- change Reload if the condition is true. A configuration change to the nvram requires a switch reload. To reload the switch, select nvram-cfg-change . Command M ...

  • Dell 9.8(0.0) - page 131

    send Send messages to one or all terminal line users. Z9500 Syntax send [*] | [line ] | [console] | [vty] Parameters * Enter the asterisk character * to send a message to all tty lines. line Send a message to a specific line. The range is from 0 to 11. console Enter the keyword console to send a message to the primary terminal line. vty Enter the k ...

  • Dell 9.8(0.0) - page 132

    service timestamps To debug and log messages, add time stamps. This command adds either the uptime or the current time and date. Z9500 Syntax service timestamps [debug | log] [datetime [localtime] [msec] [show-timezone] | uptime] To disable timestamping, use the no service timestamps [debug | log] command. Parameters debug (OPTIONAL) Enter the keyw ...

  • Dell 9.8(0.0) - page 133

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information If you do not specify parameters and enter service timestamps, it appears as service timestamps debug uptime in the running-configuration. To view the current options set for the service timestamps command, use th ...

  • Dell 9.8(0.0) - page 134

    Examples Dell#show alarms -- Minor Alarms -- Alarm Type Duration --------------------------------------------------------------- ------------ No minor alarms -- Major Alarms -- Alarm Type Duration --------------------------------------------------------------- ------------ PEM 0 in unit 0 down 25 sec PEM 2 in unit 0 down 6 sec Dell#show alarms thre ...

  • Dell 9.8(0.0) - page 135

    S9 93 86 100 95 105 S10 93 86 100 95 105 show asf View statistics about the Alternate Store and Forward (ASF) packets that are transmitted on Z9500 line cards. Z9500 Syntax show asf linecard slot-id Parameters linecard slot-id Enter the slot ID of a Z9500 line card. The range of slot IDs is from 0 to 2. Defaults all Command Modes EXEC Command Histo ...

  • Dell 9.8(0.0) - page 136

    Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on TenGigabitEthernet 2/1 Total packets: 300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Processor : RP2 --------------- No CPU traffic statistics. Dell# Related Commands debug cpu-traffic-stats — enables CPU traffic statistics for debugging. show command-h ...

  • Dell 9.8(0.0) - page 137

    Example Dell#show command-history [11/20 15:47:22]: CMD-(CLI):[service password-encryption]by default from console [11/20 15:47:22]: CMD-(CLI):[service password-encryption hostname Force10]by default from console - Repeated 3 times. [11/20 15:47:23]: CMD-(CLI):[service timestamps log datetime]by default from console [11/20 15:47:23]: CMD-(CLI):[hos ...

  • Dell 9.8(0.0) - page 138

    show command-tree Display the entire CLI command tree, and optionally, display the utilization count for each command and its options. Z9500 Syntax show command-tree [count | no] Parameters count Display the command tree with a usage counter for each command. no Display all of the commands that may be preceded by the keyword no , which is the keywo ...

  • Dell 9.8(0.0) - page 139

    Global configuration mode: aaa authentication enable command usage:1 WORD option usage: 1 default option usage: 0 enable option usage: 0 line option usage: 0 none option usage: 0 radius option usage: 1 tacacs+ option usage: 0 show console lp View the buffered boot-up log of a line card, Route Processor or Control Processor CPU, including background ...

  • Dell 9.8(0.0) - page 140

    Usage Information CAUTION: Use this command only when you are working directly with a technical support representative to troubleshoot a problem. Do not use this command unless a technical support representative instructs you to do so. show cpu-traffic-stats View CPU traffic statistics. Z9500 Syntax show cpu-traffic-stats [cp | rp | linecard { slot ...

  • Dell 9.8(0.0) - page 141

    Version Description 7.5.1.0 Introduced on the C-Series 6.2.1.1 Introduced on the E-Series. Usage Information Traffic statistics are sorted on a per-interface basis; the interface receiving the most traffic is displayed first. All CPU and port information is displayed unless a specific port or CPU is specified. Traffic information is displayed for r ...

  • Dell 9.8(0.0) - page 142

    Defaults Display interface statistics from all Z9500 CPUs. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description ...

  • Dell 9.8(0.0) - page 143

    rxPkt(COS2) :0 rxPkt(COS3) :0 rxPkt(COS4) :0 rxPkt(COS5) :0 rxPkt(COS6) :0 rxPkt(COS7) :0 rxPkt(UNIT0) :0 rxPkt(UNIT1) :0 rxPkt(UNIT2) :0 rxPkt(UNIT3) :0 transmitted :0 txRequested :0 noTxDesc :0 txError :0 txReqTooLarge :0 txDatapathErr :0 txPkt(COS0) :0 txPkt(COS1) :0 txPkt(COS2) :0 txPkt(COS3) :0 txPkt(COS4) :0 txPkt(COS5) :0 txPkt(COS6) :0 txPk ...

  • Dell 9.8(0.0) - page 144

    0.24 0.25 0xb93bd000 select_wait 54 ----RW---f 2 cfgDataS 0.00 0.00 0xb93d1000 select_wait 54 ----RW---f 2 sysCompM 0.00 0.00 0xb9470000 select_wait 54 ----RW---f 166043 statMgr 7.09 6.28 0xb94c8000 running 54 ------P--f 1579998 sflCp 37.86 43.13 0xb9560000 running 54 ------P--f 21857 snmp 0.95 1.69 0xb99e0000 running 54 ------P--f 25 usm 0.00 0.02 ...

  • Dell 9.8(0.0) - page 145

    Related Commands debug cpu-traffic-stats — enables CPU traffic statistics for debugging. show debugging View a list of all enabled debugging processes. Z9500 Syntax show debugging Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. ...

  • Dell 9.8(0.0) - page 146

    show environment View system component status (for example, temperature or power). Z9500 Syntax show environment [fan | pem | thermal-sensors | all] Parameters fan Enter the keyword all to display status information only on the fan units. pem Enter the keyword all to display status information only on the power supplies and power usage. thermal- se ...

  • Dell 9.8(0.0) - page 147

    Unit Bay Status Type FanStatus FanSpeed(rpm) Power Usage (W) -------------------------------------------------------------- 0 0 down AC up 1376 0.0 0 1 up AC up 18848 666.0 0 2 down AC up 1312 0.0 0 3 up AC up 18880 643.0 Dell#show environment fan -- Fan Status -- Unit Bay TrayStatus Fan0 Speed Fan1 Speed ------------------------------------------- ...

  • Dell 9.8(0.0) - page 148

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 149

    2 12 Media not present or accessible 2 16 QSFP 40GBASE-SR4 7503825D0169 Yes 2 20 Media not present or accessible 2 24 QSFP 40GBASE-CR4-1M APF12380010GM4 Yes 2 28 Media not present or accessible 2 32 Media not present or accessible 2 36 Media not present or accessible 2 40 QSFP 40GBASE-SR4 7503825H006J Yes 2 44 Media not present or accessible Relate ...

  • Dell 9.8(0.0) - page 150

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000- ON, and Z9500. U ...

  • Dell 9.8(0.0) - page 151

    --------------------------------------------------------------- --- --------------------------------------------------------------- --- User: secadm Last login time: Mon Feb 16 04:45:29 2015 Last login location: Line vty0 ( 10.14.1.97 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 7 day(s): ...

  • Dell 9.8(0.0) - page 152

    show memory View current memory usage on the system. Syntax show memory [cp | rp | linecard { slot-id | all}] Parameters cp Enter the keyword cp to display memory usage on the Control Processor CPU. rp Enter the keyword rp to display memory usage on the Route Processor CPU. linecard slot-id Enter the slot ID of the line card for which you want to d ...

  • Dell 9.8(0.0) - page 153

    3203928064 6953130 3196974934 3196941986 3196974934 Statistics On RP Processor =========================== Total(b) Used(b) Free(b) Lowest(b) Largest(b) 3203928064 17806442 3186121622 3186088674 3186121622 Dell#show memory cp Total(b) Used(b) Free(b) Lowest(b) Largest(b) 3203928064 6953130 3196974934 3196974934 3196974934 Dell#show memory rp Total( ...

  • Dell 9.8(0.0) - page 154

    linecard slot-id [0–2] Enter the slot ID of the line card for which you want to view CPU usage. The range of Z9500 slot IDs is from 0 to 2. Enter linecard all to display CPU usage for all line cards. The optional line card 0-2 parameter displays tasks in order of the highest CPU usage in the past five seconds. all Enter the keyword all to display ...

  • Dell 9.8(0.0) - page 155

    0x0000001a 150 15 10000 0.00% 0.00% 0.00% 0 mount_mfs ---------- More ---------- Dell#show processes cpu lp 2 details CPU utilization for five seconds: 10%/0%; one minute: 10%; five minutes: 10% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 0x00000000 976300 97630 10000 10.47% 10.14% 10.14% 0 system 0x0000012e 53570 5357 10000 0.00% 0.46 ...

  • Dell 9.8(0.0) - page 156

    0 tLogTask 0x0000012e 9060 906 10000 0.20% 0.00% 0.00% 0 tUsrRoot ---------- More ---------- Example: show processes cpu rp Dell#show processes cpu rp CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 496 20 2 10000 0.00% 0.00% 0.00% 0 ofmgr 392 20 2 10000 0.00% 0.00% ...

  • Dell 9.8(0.0) - page 157

    send-stats Enter the keyword send-stats to display information on IPC sender-side messages. cp Enter the keyword cp to view IPC message statistics on the Control Processor CPU. rp Enter the keyword rp to view IPC message statistics on the Route Processor CPU. linecard slot-id Enter the slot ID of the line card for which you want to view IPC message ...

  • Dell 9.8(0.0) - page 158

    RTT(ms) - Avg. Round Trip time for guaranteed IPC packets in millisecs NonG-S - No of non-guaranteed IPC pkts succesfully sent. This does not include those sent by SWP NonG-F - No of non-guaranteed IPC pkt transmission failures SWP-S - No of non-guaranteed SWP IPC pkts succesfully sent SWP-F - No of non-guaranteed SWP IPC pkt transmission failures ...

  • Dell 9.8(0.0) - page 159

    Source-> Destination SeqNo HiWtmk(%) M-SkSize NonG-Rcvd Pri-Dr SkFull-Dr TME: 0 -> TME: 5 0 0 129024 1 0 0 TME: 5 -> LCMGR: 2 0 0 129024 1 0 0 IPC: 0 -> IPC: 5 0 0 129024 1084 0 0 IPC: 5 -> TME: 5 58307 0 129024 0 0 0 CLI: 0 -> SYSADMTSK: 5 0 0 129024 11 0 0 CHMGR: 0 -> LCMGR: 2 53689 0 129024 4 0 0 LCMGR: 2 -> TME: 5 3906 0 ...

  • Dell 9.8(0.0) - page 160

    ACL_AGENT: 2 -> TME: 5 18120 0 129024 0 0 0 ACL_AGENT: 2 -> DSAGT: 2 35450 0 129024 0 0 0 ACL_AGENT: 2 -> FRRPAGT: 2 36661 0 163840 0 0 0 IFAGT: 2 -> TME: 5 17874 0 129024 0 0 0 IFAGT: 2 -> EVENTLOGAGENT: 5 0 0 129024 1 0 0 RTM: 0 -> FIBAGT: 2 0 1 131072 5 0 0 RTM: 0 -> FIB6: 2 0 0 131072 3 0 0 FIBAGT: 2 -> TME: 5 15595 0 12 ...

  • Dell 9.8(0.0) - page 161

    Defaults Display SWPQ statistics on all Z9500 CPUs (Control Processor, Route Processor, and line cards). Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell ...

  • Dell 9.8(0.0) - page 162

    • After retrying a defined number of times, the SWP-2-NOMORETIMEOUT timeout message is generated. • A retry (Retries) value of zero indicates that the SWP mechanism reached the maximum number of retransmissions without an acknowledgement. Example Dell#show processes ipc flow-control cp Q Statistics on CP Processor TxProcess RxProcess Cur High T ...

  • Dell 9.8(0.0) - page 163

    0 33 33 60 60 IFMGR0 LACP0 0 23 0 0 23 23 60 60 PORTMIRR0 ACL_AGENT2 0 0 0 0 0 0 50 50 IFMGR0 IGMP0 0 0 0 0 0 0 50 50 IFMGR0 IFAGT2 0 1 0 0 1 1 60 60 show processes memory View information about memory usage for processes running in the system. Z9500 Syntax show processes memory [cp | rp | linecard { slot-id | all | summary}] Parameters cp Enter th ...

  • Dell 9.8(0.0) - page 164

    Version Description 7.5.1.0 Introduced on the C-Series. Usage Information show processes memory output Field Description Total: Total system memory available MaxUsed: Total maximum memory used ever (history indicated with a time stamp) CurrentUsed: Total memory currently in use CurrentFree: Total system memory available SharedUsed: Total used share ...

  • Dell 9.8(0.0) - page 165

    464 ipSecMgr 4587520 274432 367528 0 367528 367528 443 ssMgr 4059136 286720 0 0 0 0 434 ipm 5287936 1208320 330360 0 330360 330360 419 sysd 45555712 30474240 6584722 329480 6288190 6255242 425 sysdlp 17965056 16535552 0 0 0 0 427 sysmon 704512 24576 0 0 0 0 421 sysmon 704512 24576 0 0 0 0 398 flashmntr 843776 36864 0 0 0 0 327 inetd 999424 45056 0 ...

  • Dell 9.8(0.0) - page 166

    631 login 4816896 217088 0 0 0 0 464 ipSecMgr 4587520 274432 367528 0 367528 367528 443 ssMgr 4059136 286720 0 0 0 0 434 ipm 5287936 1208320 330360 0 330360 330360 419 sysd 45555712 30474240 6584722 329480 6288190 6255242 425 sysdlp 17965056 16535552 0 0 0 0 427 sysmon 704512 24576 0 0 0 0 421 sysmon 704512 24576 0 0 0 0 398 flashmntr 843776 36864 ...

  • Dell 9.8(0.0) - page 167

    LP2 3203928064 384765952 8456566 3195471498 Example: show processes memory lp all Dell#show processes memory lp all Memory Statistics Of Linecard Processor On Slot 2 (bytes) =========================================================== Total: 3203928064, MaxUsed: 386670592, CurrentUsed: 386670592, CurrentFree: 2817257472 TaskName TotalAllocated Total ...

  • Dell 9.8(0.0) - page 168

    1654292 1654292 ofagt 367522 0 367522 367522 tnlagt 165180 0 165180 165180 frrpagt 334400 0 334400 334400 Example: show processes memory rp Dell#show processes memory rp Total : 3203928064, MaxUsed : 376844288 [01/27/2014 06:16:47] CurrentUsed: 376844288, CurrentFree: 2827083776 SharedUsed : 7993952, SharedFree : 18220472 PID Process ResSize Size A ...

  • Dell 9.8(0.0) - page 169

    122 sh 802816 2301952 0 0 0 0 74 sh 708608 2297856 0 0 0 0 30 mount_mfs 13467648 2310144 0 0 0 0 25 mount_mfs 56033280 2310144 0 0 0 0 show software ifm Display interface management (IFM) data. Z9500 Syntax show software ifm {clients [summary] | ifagt number | ifcb interface | linecard slot-id | trace-flags} Parameters clients Enter the keyword cli ...

  • Dell 9.8(0.0) - page 170

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 ...

  • Dell 9.8(0.0) - page 171

    ppStatus[0] = 0x00000001 ppStatus[1] = 0x00000001 Dell# show software ifm linecard 0 | save flash:// sh_sf_ifm_linecard0 Start saving show command report ....... show system Display operational information on all ports or a specified line card. Z9500 Syntax show system [brief | linecard slot-id ] Parameters brief (OPTIONAL) Enter the keyword brief ...

  • Dell 9.8(0.0) - page 172

    Version Description 7.6.1.0 Introduced on the S-Series. Example Dell#show system brief System MAC : 74:86:7a:ff:6f:06 Reload-Type: normal-reload [Next boot : normal-reload] -- Line Card Info -- Linecard UnitType Status ReqTyp CurTyp Version Ports --------------------------------------------------------------- 0 Linecard online Z9500LC36 Z9500LC36 9 ...

  • Dell 9.8(0.0) - page 173

    Parameters linecard slot-id Enter the slot ID of the line card for which you want to collect information for tech support. The range of Z9500 slot IDs is from 0 to 2. rp Enter the keyword rp to collect information about the Route Processor for tech support. Command Modes EXEC Privilege Command History This guide is platform-specific. For command in ...

  • Dell 9.8(0.0) - page 174

    [9/3 5:18:33] TME-(tme):f10TaskCreate: spawned PM svc(34) inst(5) p_cpid(11) [9/3 5:18:33] TME-(PM):f10TaskStartup: svc(34) inst(5) parentSvc(13) parentInst(5) taskIdx(4372): tskSvc(34) tskInst(5) p_cpid(11) p_procId(302) p_pstate(0x2000d) [9/3 5:18:33] TME-(tme):f10TaskCreate: spawned timerMgr svc(45) inst(5) p_cpid(12) [9/3 5:18:33] TME-(timerMgr ...

  • Dell 9.8(0.0) - page 175

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 176

    Dell Force10 Operating System Version: 2.0 Dell Force10 Application Software Version: 9-3(0-507) Copyright (c) 1999-2013 by Dell Inc. All Rights Reserved. Build Time: Tue Sep 17 15:03:49 PDT 2013 Build Path: /sites/sjc/work/build/buildSpaces/build16/RAINIER- DEV-9-3-0/SW/SRC FTOS uptime is 2 hour(s), 26 minute(s) System image file is "rainier- ...

  • Dell 9.8(0.0) - page 177

    0 ok 0.00V 0.00V 0.00V 0.00V 1 ok 0.00V 0.00V 0.00V 0.00V 2 ok 0.00V 0.00V 0.00V 0.00V -------------------------- show process memory on Linecard 1 ------------------ Total: 3203928064, MaxUsed: 549421056, CurrentUsed: 549421056, CurrentFree: 2654507008 TaskName TotalAllocated TotalFreed MaxHeld CurrentHolding f10appioserv 163840 147456 sysdlp 1492 ...

  • Dell 9.8(0.0) - page 178

    367522 367522 tnlagt 165180 0 165180 165180 frrpagt 466192 0 466192 466192 bfdaTaskMai 202348 0 202348 202348 Dell(conf)# Related Commands • show version — displays the Dell Networking OS version. • show system — displays the current switch status. • show environment — displays the system component status. • show util-threshold cpu Di ...

  • Dell 9.8(0.0) - page 179

    Related Commands util-threshold cpu – Configure CPU utilization thresholds. util-threshold mem – Configure memory utilization thresholds. show util-threshold memory Display the memory utilization thresholds of Z9500 CPUs. Syntax show util—threshold memory Defaults None Command Modes EXEC PRIVILEGE Command History Version 9.2(1.0) Introduced o ...

  • Dell 9.8(0.0) - page 180

    system location-led Toggle the location LED of the chassis and (optionally) the location LED of a specified Z9500 port on or off. Syntax system location-led [interface {fortyGigE | tengigabitethernet} slot / port ] {on | off} Parameters interface {fortyGigE | tengigabitether net} Specify the port type: 40-Gigabit Ethernet or 10-Gigabit Ethernet. sl ...

  • Dell 9.8(0.0) - page 181

    ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. vrf instance (Optional) Enter the keyword vrf then the VRF instance name. source- interface (OPTIONAL) Enter the keywords /source-in ...

  • Dell 9.8(0.0) - page 182

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and added support for IPv6 address on the E-Series only. terminal length Configure the number of lines displayed on the terminal screen. Z9500 Syntax terminal length screen-length Par ...

  • Dell 9.8(0.0) - page 183

    traceroute View a packet’s path to a specific device. Z9500 Syntax traceroute { host | vrf instance | ip-address | ipv6-address } Parameters host Enter the name of device. vrf instance (Optional) E-Series Only: Enter the keyword vrf then the VRF Instance name. ip-address Enter the IP address of the device in dotted decimal format. ipv6-address En ...

  • Dell 9.8(0.0) - page 184

    Version Description 7.6.1.0 Added support for the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for IPv6 address on the E-Series. E-Series Original command. Usage Information When you enter the traceroute command without specifying an IP address (Extended Traceroute), you are prompted for a target and source IP address, timeou ...

  • Dell 9.8(0.0) - page 185

    000.000 ms 000.000 ms 000.000 ms Dell# Related Commands ping — tests the connectivity to a device. undebug all Disable all debug operations on the system. Z9500 Syntax undebug all Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Ne ...

  • Dell 9.8(0.0) - page 186

    Parameters rp Enter the keyword rp to upload a trace log from the Route Processor CPU. linecard slot-id Enter the linecard slot-id parameters to specify the line-card CPU whose trace log you want to upload. cmd-history Enter the keyword cmd-history to upload the command history from the specified CPU. hw-trace Enter the keyword hw-trace to upload t ...

  • Dell 9.8(0.0) - page 187

    linecard slot-id Enter the slot ID of the line card for which you want to configure the CPU utilization time. The range of Z9500 slot IDs is from 0 to 2. all Enter the keyword all to configure the CPU utilization time on all Z9500 CPUs: Control Processor, Route Processor, and line cards. {{high | low} cpu-utilization- threshold- percentage } Enter ...

  • Dell 9.8(0.0) - page 188

    show util-threshold memory – Display the configured values of memory utilization thresholds. util-threshold memory Configure the high or low memory utilization thresholds for SNMP traps. Syntax util—threshold memory {cp |rp | linecard slot–id | all} {[high {0-100}] [low {0-100}]} Parameters cp Enter the keyword cp to configure the memory util ...

  • Dell 9.8(0.0) - page 189

    Example Dell(conf)# util-threshold memory cp high 75 low 67 Usage Information When the total memory utilization for a CPU exceeds the configured high/low threshold for a given time, a threshold notification is sent as a SNMP trap. If a low threshold value is not specified, the low threshold value is set to the same value as the high threshold value ...

  • Dell 9.8(0.0) - page 190

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information You can configure both IPv4 and IPv6 virtual addresses simultaneously ...

  • Dell 9.8(0.0) - page 191

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information The write memory command saves ...

  • Dell 9.8(0.0) - page 192

    5 802.1X An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking OS sup ...

  • Dell 9.8(0.0) - page 193

    debug dot1x Display 802.1X debugging information. Z9500 Syntax debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface ] Parameters all Enable all 802.1X debug messages. auth-pae-fsm Enable authentication PAE FSM debug messages. backend-fsm Enable backend FSM debug messages. eapol-pdu Enable the EAPOL frame trace and related ...

  • Dell 9.8(0.0) - page 194

    To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number ] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The de ...

  • Dell 9.8(0.0) - page 195

    dot1x auth-server Configure the authentication server to RADIUS. Z9500 Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell N ...

  • Dell 9.8(0.0) - page 196

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. Usage Information The prerequisites for enabling MAB-only authentication on a port are: • Enable 802.1X authentication globally on the switch ...

  • Dell 9.8(0.0) - page 197

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series TeraScale. Related Commands dot1x authentication (Interface) dot1x authentication (Interface) Enable dot1x on ...

  • Dell 9.8(0.0) - page 198

    dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Z9500 Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION ( c ...

  • Dell 9.8(0.0) - page 199

    Related Commands • dot1x auth-fail-vlan • dot1x reauthentication • dot1x reauth-max • show dot1x interface dot1x host-mode Enable single-host or multi-host authentication. Z9500 Syntax dot1x host-mode {single-host | multi-host | multi-auth} Parameters single-host Enable single-host authentication. multi-host Enable multi-host authentication ...

  • Dell 9.8(0.0) - page 200

    • Multi-supplicant mode authenticates every device attempting to connect to the network on the authenticator port. Related Commands show dot1x interface dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, the system attempts to authenticate the host based on i ...

  • Dell 9.8(0.0) - page 201

    dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Z9500 Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command. Parameters number Enter the number of times an EAP request is transmitted before a session time- ...

  • Dell 9.8(0.0) - page 202

    Parameters number Enter the number of supplicants that can be authenticated on a single port in Multi-Auth mode. The range is from 1 to 128. The default is 128 . Defaults 128 hosts can be authenticated on a single authenticator port. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platfor ...

  • Dell 9.8(0.0) - page 203

    Command Modes Auto Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on th ...

  • Dell 9.8(0.0) - page 204

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic reauthentication of the client. Z9500 Syntax dot1x reauthentication [ ...

  • Dell 9.8(0.0) - page 205

    Version Description 7.4.1.0 Introduced on the E-Series. dot1x reauth-max Configure the maximum number of times a port can reauthenticate before the port becomes unauthorized. Z9500 Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of reauthentications. The rang ...

  • Dell 9.8(0.0) - page 206

    dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Z9500 Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30 . De ...

  • Dell 9.8(0.0) - page 207

    Dell(conf)#interface tengigabitethernet 2/23 Dell(conf-if-te-2/23)#dot1x server-timeout 40 dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Z9500 Syntax dot1x supplicant-timeout seconds To return to the default, use the no dot1x supplicant-timeout command. Parameters seconds Enter a time-out ...

  • Dell 9.8(0.0) - page 208

    dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Z9500 Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535. The default is 30 . Defaults 30 seconds ...

  • Dell 9.8(0.0) - page 209

    Parameters interface Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. mac-address (Optional) MAC address of an 802. ...

  • Dell 9.8(0.0) - page 210

    Dell#show dot1x cos-mapping int g 2/21 mac-address 00:00:01:00:07:00 802.1p CoS re-map table on Gi 2/21: ---------------------------------- 802.1p CoS re-map table for Supplicant: 00:00:01:00:07:00 Dot1 Remapped Dot1p 0 7 1 6 2 5 3 4 4 3 5 2 6 1 7 0 show dot1x interface Display the 802.1X configuration of an interface. Syntax show dot1x interface i ...

  • Dell 9.8(0.0) - page 211

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added the mac-address option on the C-Series and S- Series. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. Usage Information If you enable 802.1X multi-supplicant authentication on a port, additional 802.1X ...

  • Dell 9.8(0.0) - page 212

    Mac-Auth-Bypass: Enable Mac-Auth-Bypass Only: Enable Tx Period: 3 seconds Quiet Period: 60 seconds ReAuth Max: 2 Supplicant Timeout: 30 seconds Server Timeout: 30 seconds Re-Auth Interval: 3600 seconds Max-EAP-Req: 2 Host Mode: MULTI_AUTH Max-Supplicants: 128 Port status and State info for Supplicant: 00:00:00:00:00:10 Port Auth Status: AUTHORIZED( ...

  • Dell 9.8(0.0) - page 213

    Guest VLAN id: 100 Auth-Fail VLAN: Disable Auth-Fail VLAN id: NONE Auth-Fail Max-Attempts: NONE Mac-Auth-Bypass: Enable Mac-Auth-Bypass Only: Enable Tx Period: 3 seconds Quiet Period: 60 seconds ReAuth Max: 2 Supplicant Timeout: 30 seconds Server Timeout: 30 seconds Re-Auth Interval: 3600 seconds Max-EAP-Req: 2 Host Mode: MULTI_AUTH Max-Supplicants ...

  • Dell 9.8(0.0) - page 214

    6 Access Control Lists (ACL) Access control lists (ACLs) are supported on the Dell Networking operating system on the Z9500 switch. The following types of ACL, IP prefix list, and route maps are supported: • Commands Common to all ACL Types • Common IP ACL Commands • Standard IP ACL Commands • Extended IP ACL Commands • Standard MAC ACL C ...

  • Dell 9.8(0.0) - page 215

    Parameters remark- number Enter the remark number. The range is from 0 to 65535. NOTE: You can use the same sequence number for the remark and an ACL rule. description Enter a description of up to 80 characters. Defaults Not configured. Command Modes • CONFIGURATION-IP ACCESS LIST-STANDARD • CONFIGURATION-IP ACCESS LIST-EXTENDED • CONFIGURATI ...

  • Dell 9.8(0.0) - page 216

    Related Commands show config — displays the current ACL configuration. show config Display the current ACL configuration. Z9500 Syntax show config Command Modes • CONFIGURATION-IP ACCESS LIST-STANDARD • CONFIGURATION-IP ACCESS LIST-EXTENDED • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History T ...

  • Dell 9.8(0.0) - page 217

    Common IP ACL Commands The following commands are available within both IP ACL modes (Standard and Extended) and do not have mode-specific options. When an ACL is created without a rule and then is applied to an interface, ACL behavior reflects an implicit permit. The Z9500 supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands ...

  • Dell 9.8(0.0) - page 218

    ip access-group Assign an IP access list (IP ACL) to an interface. Z9500 Syntax ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id ] To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id ] command. Parameters access-list- name Enter the name of a c ...

  • Dell 9.8(0.0) - page 219

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information You can assign one ACL (standard or extended ACL) to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs, C-Series ...

  • Dell 9.8(0.0) - page 220

    show ip access-lists Display all of the IP ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed. Syntax show ip access-lists [ access-list-name ] [interface interface ] [in | out] [vrf vrf-name ] Parameters access-list- name Enter the name of a configure ...

  • Dell 9.8(0.0) - page 221

    show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters. Syntax show ip accounting {access-list access- list-name | cam_count } interface interface [vrf vrf-name ] Parameters access-list- name Enter the name of the ACL to be displayed. cam_count List the count of the CAM rules for this ACL. inter ...

  • Dell 9.8(0.0) - page 222

    Usage Information show ip accounting access-lists Field Description “Extended IP...” Displays the name of the IP ACL. “seq 5...” Displays the filter. If the keywords count or byte were configured in the filter, the number of packets or bytes the filter processes is displayed at the end of the line. “order 4” Displays the QoS order of pr ...

  • Dell 9.8(0.0) - page 223

    Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the ...

  • Dell 9.8(0.0) - page 224

    Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 225

    permit — configures a permit filter. ip access-list standard Create a standard IP access list (IP ACL) to filter based on IP address. Z9500 Syntax ip access-list standard access-list-name To delete an access list, use the no ip access-list standard access- list-name command. Parameters access-list- name Enter a string up to 140 characters long as ...

  • Dell 9.8(0.0) - page 226

    Usage Information The system supports one ingress and one egress IP ACL per interface. The number of entries allowed per ACL is hardware-dependent. For detailed information on the number entries allowed per ACL on the Z9500, refer to the Content Addressable Memory (CAM) chapter in the Z9500 Configuration Guide . Example Dell(conf)#ip access-list st ...

  • Dell 9.8(0.0) - page 227

    order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order , the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use AC ...

  • Dell 9.8(0.0) - page 228

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information Use the order option only when you use policy-based QoS on the switch. For more in ...

  • Dell 9.8(0.0) - page 229

    Step-to- Increment Enter the step to increment the sequence number. For IPv4 and IPv6 ACLs, the range is 0 to 4294967290; for MAC ACLs, the range is 0 to 65535. Defaults The sequence number of ACL entries increases in multiples of 5; for example, seq 5, seq 10, seq 15 ... Command Modes • EXEC • EXEC Privilege Command History This guide is platf ...

  • Dell 9.8(0.0) - page 230

    Parameters prefix-list- name Enter the name of the configured prefix list, up to 140 characters long. StartingSeqNu m Enter the starting sequence number to resequence. The range is from 0 to 65535. Step-to- Increment Enter the step to increment the sequence number. The range is from 1 to 65535. Defaults none Command Modes • EXEC • EXEC Privileg ...

  • Dell 9.8(0.0) - page 231

    Parameters sequence- number Enter a number from 0 to 4294967290. deny Enter the keyword deny to configure a filter to drop packets meeting this condition. permit Enter the keyword permit to configure a filter to forward packets meeting this criteria. source Enter an IP address in dotted decimal format of the network from which the packet was receiv ...

  • Dell 9.8(0.0) - page 232

    interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide . Defaults Not configured Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevan ...

  • Dell 9.8(0.0) - page 233

    By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Use the monitor option only when you are using flow-based monitoring. For more information, refer to the Port Monitoring chapter of the Z9500 C ...

  • Dell 9.8(0.0) - page 234

    ip-protocol- number Enter a number from 0 to 255 to deny based on the protocol identified in the IP protocol header. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous. ...

  • Dell 9.8(0.0) - page 235

    Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide . Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The fol ...

  • Dell 9.8(0.0) - page 236

    ip access-list extended — creates an extended ACL. deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Z9500 Syntax deny icmp { source–ip—address mask | any | host ip-address } { destination mask | any | host ip-address } [log] [dscp] [[count [bytes]] [order] [monitor] [fragments] To remove ...

  • Dell 9.8(0.0) - page 237

    monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide . frag ...

  • Dell 9.8(0.0) - page 238

    ICMP Message Type Keywords ICMP Message Type Name administratively- prohibited Administratively prohibited alternate-address Alternate host address conversion-error Datagram conversion error dod-host- prohibited Host prohibited dod-net- prohibited Net prohibited echo Echo echo-reply Echo reply general- parameter- problem Parameter problem host-isol ...

  • Dell 9.8(0.0) - page 239

    ICMP Message Type Keywords ICMP Message Type Name no-room-for- option Parameter required but no room option-missing Parameter required but not present packet-too-big Fragmentation needed and DF set parameter- problem All parameter problems port-unreachable Port unreachable precedence- unreachable Precedence cutoff protocol- unreachable Protocol unr ...

  • Dell 9.8(0.0) - page 240

    [fragments] [log [interval minutes ] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny tcp { source mask | any | host ip-address } { destination mask | any | host ip-address } command. Parameters source Enter t ...

  • Dell 9.8(0.0) - page 241

    • 20 and 21 = FTP • 25 = SMTP • 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets the fil ...

  • Dell 9.8(0.0) - page 242

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp . 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1 ...

  • Dell 9.8(0.0) - page 243

    3 0001000000000000 1111100000000000 4096 6143 2048 4 0001100000000000 1111110000000000 6144 7167 1024 5 0001110000000000 1111111000000000 7168 7679 512 6 0001111000000000 1111111100000000 7680 7935 256 7 0001111100000000 1111111111000000 7936 7999 64 8 0001111101000000 1111111111111111 8000 8000 1 Total Ports: 4001 Example An ACL rule with a TCP po ...

  • Dell 9.8(0.0) - page 244

    operator (OPTIONAL) Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command) port port Enter the application layer port number. Enter two port numbers if using the range logical operand. The ran ...

  • Dell 9.8(0.0) - page 245

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp . 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1 ...

  • Dell 9.8(0.0) - page 246

    8 0001111101000000 1111111111111111 8000 8000 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To #Covered 1 0000000000000000 1111110000000000 0 1023 1024 Total Ports: 1024 Related Commands deny — assigns a filter to deny IP traffic. deny tcp — assigns a filter to deny TCP traf ...

  • Dell 9.8(0.0) - page 247

    Version Description 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information The ...

  • Dell 9.8(0.0) - page 248

    any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname. destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. ...

  • Dell 9.8(0.0) - page 249

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ...

  • Dell 9.8(0.0) - page 250

    permit icmp Configure a filter to allow all or specific ICMP messages. Z9500 Syntax permit icmp { source mask | any | host ip-address } { destination mask | any | host ip-address } [dscp] [count [bytes]] [order] [fragments] [log [interval minutes ] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • Use the no seq ...

  • Dell 9.8(0.0) - page 251

    threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq , permit , or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval f ...

  • Dell 9.8(0.0) - page 252

    By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring . NOTE: When ACL lo ...

  • Dell 9.8(0.0) - page 253

    dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. operator (OPTIONAL) Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter th ...

  • Dell 9.8(0.0) - page 254

    fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of th ...

  • Dell 9.8(0.0) - page 255

    Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry. The range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range. Example An ACL rule with a TCP port range o ...

  • Dell 9.8(0.0) - page 256

    Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the ...

  • Dell 9.8(0.0) - page 257

    interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the ...

  • Dell 9.8(0.0) - page 258

    Use the monitor option only when you are using flow-based monitoring. For more information, refer to the Port Monitoring chapter of the Z9500 Configuration Guide . By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monito ...

  • Dell 9.8(0.0) - page 259

    resequence prefix-list ipv4 Re-assign sequence numbers to entries of an existing prefix list. Z9500 Syntax resequence prefix-list ipv4 { prefix-list-name StartingSeqNum Step-to-increment } Parameters prefix-list- name Enter the name of the configured prefix list, up to 140 characters long. StartingSeqNu m Enter the starting sequence number to reseq ...

  • Dell 9.8(0.0) - page 260

    seq Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter. Z9500 Syntax seq sequence-number {deny | permit} { ip-protocol-number | icmp | ip | tcp | udp} { source mask | any | host ip-address } { destination mask | any | host ip-address } [ operator port [ port ]] [count [byte] | [dscp value ] [ ...

  • Dell 9.8(0.0) - page 261

    • range = inclusive range of ports (you must specify two ports for the port parameter.) port port (OPTIONAL) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: • 23 = Telnet • 20 and 21 = FTP • 25 ...

  • Dell 9.8(0.0) - page 262

    monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide . Defa ...

  • Dell 9.8(0.0) - page 263

    • If sequence-number is not configured, the rules with the same order value are ordered according to their configuration order. • If sequence-number is configured, the sequence-number is used as a tie breaker for rules with the same order. When you use the log option, the CP processor logs detail the packets that match. Depending on how many pa ...

  • Dell 9.8(0.0) - page 264

    Term heading Description heading Command Modes ACL-VLAN-GROUP CONFIGURATION Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S4810, S4820T, and Z9000. Usage Information You can configure up to eight different ACL VLAN groups at a time on the switch. When you configure an ACL VLAN group, you enter ACL ...

  • Dell 9.8(0.0) - page 265

    vlanaclopt <0-2> Allocate a number of FP blocks of CAM for CAM optimization of ACL VLAN operation. Default To reset the number FP blocks allocated for ACL VLAN processes, enter the default keyword with the cam-acl-vlan command. By default, 0 FP blocks are allocated for ACL VLAN operations on the switch. Command Modes ACL-VLAN-GROUP CONFIGURAT ...

  • Dell 9.8(0.0) - page 266

    ip access-group (ACL VLAN Group) Apply an egress IP ACL to the ACL VLAN group. Syntax ip access-group access-list-name out implicit-permit Parameters access-list- name Enter the name of the egress IP ACL to be applied to member interfaces of the VLAN group (140 characters maximum). out Enter the keyword out to apply the ACL to outgoing traffic. imp ...

  • Dell 9.8(0.0) - page 267

    Command Modes ACL-VLAN-GROUP CONFIGURATION (conf-acl-vl-grp) Command History Version Description 9.5(0.0) Introduced on the Z9500. 9.3(0.0) Introduced on the S4810, S4820T, and Z9000. Usage Information At a maximum, there can be only 32 VLAN members in all ACL VLAN groups. A VLAN can belong to only one ACL VLAN group at a time. You can create an AC ...

  • Dell 9.8(0.0) - page 268

    NOTE: Some group names and some access list names are truncated. Dell#show acl-vlan-group Group Name Egress IP Acl Vlan Members TestGroupSeventeenTwenty SpecialAccessOnlyExperts 100,200,300 CustomerNumberIdentifica AnyEmployeeCustomerEleve 2-10,99 HostGroup Group5 1,1000 The following sample output shows the line-by-line style display when using th ...

  • Dell 9.8(0.0) - page 269

    Usage Information After you allocate FP blocks of CAM to ACL VLAN operation, you must reboot the switch to enable ACL VLAN optimization. The following table describes the output fields of the show cam-acl-vlan command: Field Description Chassis Vlan Cam ACL Details about the CAM blocks allocated for ACLs for various VLAN operations at a system-wide ...

  • Dell 9.8(0.0) - page 270

    show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow). Syntax show cam-usage [acl | router | switch] Parameters acl (OPTIONAL) Enter the keyword acl to display Layer 2 and Layer 3 ACL CAM usage. router (OPTIONAL) Enter the keyword router to display Layer 3 CAM u ...

  • Dell 9.8(0.0) - page 271

    Field Description Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs Example 1 Dell#show cam-usage Linecard|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|=================|=============| =============|============== 1 | 0 | IN- ...

  • Dell 9.8(0.0) - page 272

    =============|============ 11 | 0 | IN-L2 ACL | 1008 | 0 | 1008 | | IN-L3 ACL | 12288 | 2 | 12286 | | OUT-L2 ACL | 1024 | 2 | 1022 | | OUT-L3 ACL | 1024 | 0 | 1024 Example 3 Dell#show cam-usage router Linecard|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|=================|=============| =============|============= ...

  • Dell 9.8(0.0) - page 273

    11 | 1 | IN-L2 ACL | 7152 | 0 | 7152 | | IN-L2 FIB | 32768 | 1081 | 31687 | | OUT-L2 ACL | 0 | 0 | 0 show running config acl-vlan-group Display the running configuration of ACL VLAN groups. Syntax show running config acl-vlan-group group-name Parameters group-name Display the specified ACL VLAN group (140 characters maximum). Default None Command M ...

  • Dell 9.8(0.0) - page 274

    Common MAC ACL Commands The following commands are available within both MAC ACL modes (Standard and Extended) and do not have mode-specific options. These commands allow you to clear, display, and assign MAC ACL configurations. The Z9500 supports both Ingress and Egress MAC ACLs. You can apply a MAC ACL on physical, port-channel and VLAN interface ...

  • Dell 9.8(0.0) - page 275

    mac access-group Apply a MAC ACL to traffic entering or exiting an interface. You can apply a MAC ACL on a physical, port- channel, or VLAN interface. Z9500 Syntax mac access-group access-list-name {in [vlan vlan-range ] | out} To delete a MAC access-group, use the no mac access-group mac-list- name command. Parameters access-list- name Enter the n ...

  • Dell 9.8(0.0) - page 276

    Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information You can assign one ACL (standard or extended) to an interface. If you apply a MAC ACL on a VLAN: • None of the VLAN members can have another ACL applied which has an entry for the VLAN. • The VLAN cannot belong to an ACL VLAN group. If ...

  • Dell 9.8(0.0) - page 277

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 278

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 279

    Standard MAC ACL Commands When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. These commands configure standard MAC ACLs. The Z9500 support both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC ...

  • Dell 9.8(0.0) - page 280

    interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the ...

  • Dell 9.8(0.0) - page 281

    Related Commands permit — configures a MAC address filter to pass packets. seq — configures a MAC address filter with a specified sequence number. mac access-list standard To configure a standard MAC ACL, name a new or existing MAC access control list (MAC ACL) and enter MAC ACCESS LIST mode. Also refer to the Commands Common to all ACL Types s ...

  • Dell 9.8(0.0) - page 282

    The number of entries allowed per ACL is hardware-dependent. For detailed information on the number entries allowed per ACL on the Z9500, refer to the Content Addressable Memory (CAM) chapter in the Z9500 Configuration Guide . Example Dell(conf)#mac-access-list access-list standard TestMAC Dell(config-std-macl)#? deny Specify packets to reject desc ...

  • Dell 9.8(0.0) - page 283

    of ACL logs is terminated with the seq , permit , or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is descri ...

  • Dell 9.8(0.0) - page 284

    NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands deny — configures a MAC ACL filter to drop packets. seq —configure a MAC ACL filter with a specified sequence number. seq To a deny or permit filter in a MAC acces ...

  • Dell 9.8(0.0) - page 285

    interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the ...

  • Dell 9.8(0.0) - page 286

    Related Commands deny — configures a filter to drop packets. permit — configures a filter to forward packets. Extended MAC ACL Commands When an access-list is created without any rule and then applied to an interface, ACL behavior reflects implicit permit. The following commands configure Extended MAC ACLs. The Z9500 supports both Ingress and E ...

  • Dell 9.8(0.0) - page 287

    mac- destination- address Enter the destination MAC address and mask in nn:nn:nn:nn:nn:nn format. mac- destination- address-mask Specify which bits in the MAC address must match. The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that matc ...

  • Dell 9.8(0.0) - page 288

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. Usage I ...

  • Dell 9.8(0.0) - page 289

    cpu-qos Enter the keyword cpu-qos to configure an extended MAC ACL to be used only to filter protocol traffic for control- plane policing (CoPP). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Gu ...

  • Dell 9.8(0.0) - page 290

    packets 191402152148 bytes) seq 20 permit any any ev2 eq 806 count bytes (74481486 packets 5031686754 bytes) seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands mac access-list standard — configures a standard MAC access list. show mac accounting access-list — displays MAC access list configurations ...

  • Dell 9.8(0.0) - page 291

    mac- destination- address-mask Specify which bits in the MAC address must be matched. The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the f ...

  • Dell 9.8(0.0) - page 292

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. Usage Information When you use the log op ...

  • Dell 9.8(0.0) - page 293

    Parameters sequence- number Enter a number as the filter sequence number. The range is from zero (0) to 65535. deny Enter the keyword deny to drop any traffic matching this filter. permit Enter the keyword permit to forward any traffic matching this filter. any Enter the keyword any to filter all packets. host mac- address Enter the keyword host an ...

  • Dell 9.8(0.0) - page 294

    interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the ...

  • Dell 9.8(0.0) - page 295

    permit — configures a filter to forward packets. IP Prefix List Commands When you create an access-list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. To configure or enable IP prefix lists, use these commands. access-class Apply a standard ACL to a terminal line. Syntax access-class access-list-nam ...

  • Dell 9.8(0.0) - page 296

    Version Description 7.8.1.0 Increase the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information When you use the access-class access-list-name command without specifying the ipv4 o ...

  • Dell 9.8(0.0) - page 297

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 298

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 299

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. ...

  • Dell 9.8(0.0) - page 300

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 In ...

  • Dell 9.8(0.0) - page 301

    ip-prefix /nn (OPTIONAL) Specify an IP prefix in the network/length format. For example, 35.0.0.0/8 means match the first 8 bits of address 35.0.0.0. ge min-prefix- length (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32. le max-prefix- length (OPTIONAL) Enter the keyword le and then en ...

  • Dell 9.8(0.0) - page 302

    show config Display the current PREFIX-LIST configurations. Z9500 Syntax show config Command Modes PREFIX-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for t ...

  • Dell 9.8(0.0) - page 303

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 304

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 305

    continue To a route-map entry with a higher sequence number, configure a route-map. Z9500 Syntax continue [ sequence-number ] Parameters sequence- number (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command informat ...

  • Dell 9.8(0.0) - page 306

    • A successful match with a continue clause, the route map executes the set clauses and then goes to the specified route map entry upon execution of the continue clause. • If the next route map entry contains a continue clause, the route map executes the continue clause if a successful match occurs. • If the next route map entry does not cont ...

  • Dell 9.8(0.0) - page 307

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced. Related Commands route-map — enables a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Z9500 Syntax match as-path as-path-name To dele ...

  • Dell 9.8(0.0) - page 308

    Version Description 6.1.1.0 Introduced on the E-Series. Related Commands set as-path — adds information to the BGP AS_PATH attribute. match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Z9500 Syntax match community community-list-name [exact] To delete a community match filter, use the no ...

  • Dell 9.8(0.0) - page 309

    neighbor send-community — sends COMMUNITY attribute to peer or peer group. match interface To match routes whose next hop is on the interface specified, configure a filter. Z9500 Syntax match interface interface To remove a match, use the no match interface interface command. Parameters interface Enter the following keywords and slot/port or numb ...

  • Dell 9.8(0.0) - page 310

    Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Related Commands match ip address — redistributes routes that match an IP address. match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. ...

  • Dell 9.8(0.0) - page 311

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Related Commands match interface — redistributes routes ...

  • Dell 9.8(0.0) - page 312

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-S ...

  • Dell 9.8(0.0) - page 313

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 314

    Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 315

    igp Enter the keyword igp to match routes originating within the same AS. incomplete Enter the keyword incomplete to match routes with incomplete routing information. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking ...

  • Dell 9.8(0.0) - page 316

    Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 317

    Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 318

    permit (OPTIONAL) Enter the keyword permit to set the route map default as permit. If you do not specify a keyword, the default is permit . deny (OPTIONAL) Enter the keyword deny to set the route map default as deny. sequence- number (OPTIONAL) Enter a number to identify the route map for editing and sequencing with other route maps. You are prompt ...

  • Dell 9.8(0.0) - page 319

    set as-path To modify the AS path for border gateway protocol (BGP) routes, configure a filter. Z9500 Syntax set as-path prepend as-number [... as-number ] To remove an AS-Path setting, use the no set as-path {prepend as-number | tag} command. Parameters prepend as- number Enter the keyword prepend and then enter up to eight AS numbers to be insert ...

  • Dell 9.8(0.0) - page 320

    show ip community-lists — displays configured IP Community access lists. set automatic-tag To automatically compute the tag value of the route, configure a filter. Z9500 Syntax set automatic-tag To return to the default, enter no set automatic-tag . Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. ...

  • Dell 9.8(0.0) - page 321

    set comm-list delete To remove the specified community list from the BGP route’s COMMUNITY attribute, configure a filter. Z9500 Syntax set comm-list community-list-name delete To insert the community list into the COMMUNITY attribute, use the no set comm-list community-list-name delete command. Parameters community- list-name Enter the name of an ...

  • Dell 9.8(0.0) - page 322

    Related Commands ip community-list — configures community access list. match community — redistributes routes that match the COMMUNITY attribute. set community — specifies a COMMUNITY attribute. set community Allows you to assign a BGP COMMUNITY attribute. Z9500 Syntax set community { community-number | local-as | no-advertise | no- export | ...

  • Dell 9.8(0.0) - page 323

    Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 324

    level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is plat ...

  • Dell 9.8(0.0) - page 325

    Parameters value Enter a number as the LOCAL_PREF attribute value. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the ...

  • Dell 9.8(0.0) - page 326

    metric-value Enter a number as the new metric value. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Ne ...

  • Dell 9.8(0.0) - page 327

    type-1 Enter the keyword type-1 to assign the OSPF Type 1 metric. type-2 Enter the keyword type-2 to assign the OSPF Type 2 metric. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . T ...

  • Dell 9.8(0.0) - page 328

    Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 329

    Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 330

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Related Commands set automatic-tag — computes the tag value of the route. ...

  • Dell 9.8(0.0) - page 331

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information If you do not use the s ...

  • Dell 9.8(0.0) - page 332

    route-map hopper permit 10 Dell(config-route-map)# show route-map Display the current route map configurations. Z9500 Syntax show route-map [ map-name ] Parameters map-name (OPTIONAL) Enter the name of a configured route map, up to 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command ...

  • Dell 9.8(0.0) - page 333

    AS-Path Commands The following commands configure AS-Path ACLs. ip as-path access-list Enter AS-PATH ACL mode and configure an access control list based on the BGP AS_PATH attribute. Z9500 Syntax ip as-path access-list as-path-name Parameters as-path-name Enter the access-list name, up to 140 characters. Defaults Not configured. Command Modes CONFI ...

  • Dell 9.8(0.0) - page 334

    show ip as-path-access-lists Display the all AS-PATH access lists configured on the E-Series. Z9500 Syntax show ip as-path-access-lists Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The ...

  • Dell 9.8(0.0) - page 335

    ip community-list Enter COMMUNITY-LIST mode and create an IP community-list for BGP. Z9500 Syntax ip community-list comm-list-name To delete a community-list, use the no ip community-list comm-list-name command. Parameters comm-list- name Enter a text string as the name of the community-list, up to 140 characters. Command Modes CONFIGURATION Comman ...

  • Dell 9.8(0.0) - page 336

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 337

    To remove this filter, use the no seq sequence-number command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous. any Enter the keyword any to specify that a ...

  • Dell 9.8(0.0) - page 338

    Defaults Disabled Command Modes CONFIGURATION Example Dell(conf)#feature udf-acl Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Descripti ...

  • Dell 9.8(0.0) - page 339

    Example Dell(conf-udf-tcam)#key innerL3header udf-id 6 packetbase innerL3Header offset 0 length 2 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. ...

  • Dell 9.8(0.0) - page 340

    Command Modes CONFIGURATION-UDF TCAM Example Dell(conf-udf-tcam)#match l2ethertype ipv4 ipprotocol 4 vlantag any Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for ...

  • Dell 9.8(0.0) - page 341

    Command Modes CONFIGURATION-STANDARD-ACCESS-LIST mode CONFIGURATION-EXTENDED-ACCESS-LIST mode Example Dell(config-ext-nacl)#permit ip any any udf-pkt-format ipinip udf-qualifier-value ipnip_val1 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refer ...

  • Dell 9.8(0.0) - page 342

    udf-id Assign value for each configured UDF ID in the given UDF TCAM profile. Syntax udf-id id value mask To return to the default settings, use the no udf-id 1-12 value mask command. Parameters id Enter the UDF ID range. The range is from 1 to 12. value Enter the value for the UDF in Hex, up to 24 bytes. mask Enter the mask for the UDF in Hex, up ...

  • Dell 9.8(0.0) - page 343

    Defaults None Command Modes CONFIGURATION-UDF TCAM Example Dell(conf-udf-tcam)# udf-qualifier-value ipnip_val1 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for t ...

  • Dell 9.8(0.0) - page 344

    Version Description 9.8(0.0) Introduced on the S6000, Z9500. 344 Access Control Lists (ACL) ...

  • Dell 9.8(0.0) - page 345

    7 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection. The Dell Networking OS implementation is based on the standards specified in the IETF Draft draft-ietf- bfd-base-03. bfd all-neighbors Enable BFD sessions with all neighbors discovered by ...

  • Dell 9.8(0.0) - page 346

    • Passive — The passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is active . Defaults Refer to Parameters . Command Modes ROUTER OSPF ROUTER OSPFv3 ROUTER BGP ROUTER ISIS INTERFACE (BFD for VRRP only) Command History This guide is platform-specific. For comm ...

  • Dell 9.8(0.0) - page 347

    mode do not inherit the global BFD enable/disable values configured with the bfd all-neighbors command or configured for the peer group to which a neighbor belongs. The neighbors inherit only the global timer values. You can only enable BFD for VRRP in INTERFACE command mode ( vrrp bfd all-neighbors ). Related Commands show bfd neighbors — displa ...

  • Dell 9.8(0.0) - page 348

    bfd enable (Configuration) Enable BFD on all interfaces. Z9500 Syntax bfd enable Disable BFD using the no bfd enable command. Defaults BFD is disabled by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference ...

  • Dell 9.8(0.0) - page 349

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 350

    Defaults Refer to Parameters . Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on ...

  • Dell 9.8(0.0) - page 351

    Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 7.4.1.0 Introduced on the E-Series. Usage Information Protocol Liveness is a feature that notifies the BFD Manager when a client protocol (for example, OSPF and ISIS) is disabled. When a client is disabled, all BFD sessions for ...

  • Dell 9.8(0.0) - page 352

    The default is Active . Defaults See Parameters Command Modes CONFIGURATION Command History Version Description 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on Z9000, S4810, and S4820T. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Related Commands show bfd neighbors ? ...

  • Dell 9.8(0.0) - page 353

    multiplier value Enter the keyword multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3 . role [active | passive] Enter the role that the local system assumes: • Active — The active system initiates the BFD session. Both systems can be active for the same ...

  • Dell 9.8(0.0) - page 354

    Parameters ip-address Enter the IP address of the BGP neighbor that you want to explicitly enable for BFD sessions in dotted decimal format (A.B.C.D). peer-group- name Enter the name of the peer group that you want to explicitly enable for BFD sessions. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For comm ...

  • Dell 9.8(0.0) - page 355

    neighbor bfd disable Explicitly disable a BFD session with a BGP neighbor or a BGP peer group. Z9500 Syntax neighbor { ip-address | peer-group-name } bfd disable Parameters ip-address Enter the IP address of the BGP neighbor that you want to explicitly disable for BFD sessions in dotted decimal format (A.B.C.D). peer-group- name Enter the name of t ...

  • Dell 9.8(0.0) - page 356

    Related Commands show bfd neighbors — displays the BFD neighbor information on all interfaces or a specified interface. show bfd neighbors Display BFD neighbor information on all interfaces or a specified interface. Z9500 Syntax show bfd neighbors interface [detail] Parameters interface Enter one of the following keywords and slot/port or number ...

  • Dell 9.8(0.0) - page 357

    Version Description 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for BFD for VLAN and port-channel interfaces on the E-Series. 7.4.1.0 Introduced BFD on physical ports on the E-Series. Example Dell#show bfd neighbors * - Active session role Ad Dn - Admin Down B - BGP C - CLI I - ISIS O - OSP ...

  • Dell 9.8(0.0) - page 358

    vrrp bfd Establish a BFD session with VRRP neighbors. Z9500 Syntax vrrp bfd {all-neighbors | neighbor ip-address } [interval interval min_rx min_rx multiplier value role {active | passive}] To undo your VRRP BFD configuration, use the no vrrp bfd {all-neighbors | neighbor ip-address } [interval interval min_rx min_rx multiplier value role {active | ...

  • Dell 9.8(0.0) - page 359

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. When BFD is enabled with VRRP neighbors, the VRRP protocol registers with the ...

  • Dell 9.8(0.0) - page 360

    8 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including fu ...

  • Dell 9.8(0.0) - page 361

    ipv4 vrf vrf- name Enter the keyword ipv4 followed by the keyword vrf and then the name of the VRF to enable VRF mode. NOTE: Use this attribute to start a BGP instance corresponding to either a specific address family in a default VRF or an IPv4 address family in a non-default VRF. ipv6 unicast Enter the keyword ipv6 followed by the keyword unicast ...

  • Dell 9.8(0.0) - page 362

    Parameters ip-address mask Enter the IP address and mask of the route to be the aggregate address. Enter the IP address in dotted decimal format (A.B.C.D) and mask in /prefix format (/x). advertise-map map-name (OPTIONAL) Enter the keywords advertise-map then the name of a configured route map to set filters for advertising an aggregate route. as-s ...

  • Dell 9.8(0.0) - page 363

    Usage Information At least one of the routes included in the aggregate address must be in the BGP routing table for the configured aggregate to become active. If routes within the aggregate are constantly changing, do not add the as-set parameter to the aggregate as the aggregate flaps to keep track of the changes in the AS_PATH. In route maps used ...

  • Dell 9.8(0.0) - page 364

    Defaults Disabled Command Modes • ROUTER BGP • ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9 ...

  • Dell 9.8(0.0) - page 365

    Version Description 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Usage Information Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line ...

  • Dell 9.8(0.0) - page 366

    Example Dell(conf)#router bgp 1 Dell(conf-router_bgp)#bgp asnotation asdot Dell(conf-router_bgp)#ex Dell(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot Dell(conf)#router bgp 1 Dell(conf-router_bgp)#bgp asnotation asdot+ Dell(conf-router_bgp)#ex Dell(conf)#do show run | grep bgp router bgp 1 bgp four-octet-a ...

  • Dell 9.8(0.0) - page 367

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath as-path multipath-relax Include prefixes received from different AS paths ...

  • Dell 9.8(0.0) - page 368

    bgp bestpath med confed Enable MULTI_EXIT_DISC (MED) attribute comparison on paths learned from BGP confederations. Z9500 Syntax bgp bestpath med confed To disable MED comparison on BGP confederation paths, enter the no bgp bestpath med confed command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For c ...

  • Dell 9.8(0.0) - page 369

    Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 370

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced Usage Information Configuring this option retains the current best-path. When sessions are then reset, the oldest received path is chosen as the best-path. bgp client-to-client reflection Allows you to enable route reflection between clients in ...

  • Dell 9.8(0.0) - page 371

    bgp cluster-id Assign a cluster ID to a BGP cluster with more than one route reflector. Z9500 Syntax bgp cluster-id { ip-address | number } To delete a cluster ID, use the no bgp cluster-id { ip-address | number } command. Parameters ip-address Enter an IP address as the route reflector cluster ID. number Enter a route reflector cluster ID as a num ...

  • Dell 9.8(0.0) - page 372

    show ip bgp cluster-list — views paths with a cluster ID. bgp confederation identifier Configure an identifier for a BGP confederation. Z9500 Syntax bgp confederation identifier as-number To delete a BGP confederation identifier, use the no bgp confederation identifier as-number command. Parameters as-number Enter the AS number. The range is from ...

  • Dell 9.8(0.0) - page 373

    The system accepts confederation EBGP peers without a LOCAL_PREF attribute. The software sends AS_CONFED_SET and accepts AS_CONFED_SET and AS_CONF_SEQ. Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp confederation peers Specify the autonomous systems (ASs) that belong to the BGP confederation. Z9500 Sy ...

  • Dell 9.8(0.0) - page 374

    The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. After specifying autonomous systems numbers for the BGP confederation, recycle the peers to update their configuration. This command automatically restarts the BGP in ...

  • Dell 9.8(0.0) - page 375

    Only match commands in the configured route map are supported. Defaults Disabled. Command Modes • ROUTER BGP • ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Netwo ...

  • Dell 9.8(0.0) - page 376

    Defaults 100 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19 ...

  • Dell 9.8(0.0) - page 377

    Usage Information Configuring or un-configuring the command will bring down and bring up the BGP Route Manager, this will result in tear down and re-establishment of all active sessions. Link Bandwidth has to be configured on the router in order to tell it to associate Link Bandwidth with prefixes (paths) and/or to use Link Bandwidth in BGP Multipa ...

  • Dell 9.8(0.0) - page 378

    Usage Information This command is enabled by default, that is for all updates received from EBGP peers, BGP ensures that the first AS of the first AS segment is always the AS of the peer. If not, the update is dropped and a counter is increments. Use the show ip bgp neighbors command to view the “failed enforce-first-as check” counter. If you d ...

  • Dell 9.8(0.0) - page 379

    bgp four-octet-as-support Enable 4-byte support for the BGP process. Z9500 Syntax bgp four-octet-as-support To disable fast external failover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platfo ...

  • Dell 9.8(0.0) - page 380

    bgp graceful-restart To support graceful restart as a receiver only, enable graceful restart on a BGP neighbor, a BGP node, or designate a local router. Z9500 Syntax bgp graceful-restart [restart-time seconds ] [stale-path-time seconds ] [role receiver-only] To return to the default, use the no bgp graceful-restart command. Parameters restart-time ...

  • Dell 9.8(0.0) - page 381

    BGP graceful restart is active only when the neighbor becomes established. Otherwise it is disabled. Graceful-restart applies to all neighbors with established adjacency. bgp log-neighbor-changes Enable logging of BGP neighbor resets. Z9500 Syntax bgp log-neighbor-changes To disable logging, use the no bgp log-neighbor-changes command. Defaults Ena ...

  • Dell 9.8(0.0) - page 382

    Defaults Disabled (that is, paths/routes for the same destination but from different ASs do not have their MEDs compared). Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Del ...

  • Dell 9.8(0.0) - page 383

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.2(1.0) Introduced on the Z9500. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.1 ...

  • Dell 9.8(0.0) - page 384

    Version 9.2(1.0) Introduced on the Z9500. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced Usage Information BGP uses regular expressions (regex) to filter ro ...

  • Dell 9.8(0.0) - page 385

    bgp router-id Assign a user-given ID to a BGP router. Z9500 Syntax bgp router-id ip-address To delete a user-assigned IP address, use the no bgp router-id command. Parameters ip-address Enter an IP address in dotted decimal format to reset only that BGP neighbor. Defaults The router ID is the highest IP address of the Loopback interface or, if no L ...

  • Dell 9.8(0.0) - page 386

    Defaults Off Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.1(0. ...

  • Dell 9.8(0.0) - page 387

    direction {both | rx | tx} Enter the keyword direction and a direction — either rx for inbound, tx for outbound, or both. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The ...

  • Dell 9.8(0.0) - page 388

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced Related Commands capture bgp-pdu neighbor — enables capture of an IPv4 BGP neighbor packet. show capt ...

  • Dell 9.8(0.0) - page 389

    soft (OPTIONAL) Enter the keyword soft to configure and activate policies without resetting the BGP TCP session, that is, BGP Soft Reconfiguration. NOTE: If you enter the clear ip bgp ip-address soft command, both inbound and outbound policies are reset. in (OPTIONAL) Enter the keyword in to activate only inbound policies. out (OPTIONAL) Enter the ...

  • Dell 9.8(0.0) - page 390

    Related Commands bgp recursive-bgp-next-hop — disables next-hop resolution through other routes learned by the BGP. clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state. Z9500 Syntax clear ip bgp [vrf vrf-name ] [ipv4 [multicast | unicast] | ipv6 unicast] [dampening [ ipv4-address mask | ...

  • Dell 9.8(0.0) - page 391

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information After you enter this command, the software deletes the history routes and returns the suppressed routes to the Active state. The clear ip bgp dampening command does not clea ...

  • Dell 9.8(0.0) - page 392

    filter-list as- path-name (OPTIONAL) Enter the keywords filter-list then the name of a configured AS-PATH list. regexp regular- expression (OPTIONAL) Enter the keyword regexp then regular expressions. Use one or a combination of the following: • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pat ...

  • Dell 9.8(0.0) - page 393

    Related Commands show debugging — views the enabled debugging operations. show ip bgp flap-statistics — views the BGP flap statistics. undebug all — disables all debugging operations. clear ip bgp peer-group Reset a peer-group’s BGP sessions. Z9500 Syntax clear ip bgp [vrf vrf-name ] peer-group peer-group-name [ipv4 [multicast | unicast] | ...

  • Dell 9.8(0.0) - page 394

    Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, ...

  • Dell 9.8(0.0) - page 395

    ipv6 Enter the ipv6 IP address to view the IPV6 route information. keepalives Enter the keyword keepalives to view BGP keepalives. notifications Enter the keyword notifications to view BGP notifications. soft- reconfiguration Enter the keywords soft-reconfiguration to view only information on inbound BGP soft reconfiguration. updates Enter the keyw ...

  • Dell 9.8(0.0) - page 396

    debug ip bgp dampening View information on routes being dampened. Z9500 Syntax debug ip bgp [vrf vrf-name ] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corres ...

  • Dell 9.8(0.0) - page 397

    debug ip bgp events Display information on local BGP state changes and other BGP events. Z9500 Syntax debug ip bgp [vrf vrf-name ] [ A.B.C.D | X:X:X:X::X | peer-group peer-group-name ] events [in | out] To disable debugging, use the no debug ip bgp [ A.B.C.D | X:X:X:X::X | peer-group peer-group-name ] events [in | out] command. Parameters vrf vrf-n ...

  • Dell 9.8(0.0) - page 398

    Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp keepalives Display information about BGP keepalive messages. Z9500 Syntax debug ip bgp [vrf vrf-name ] [ A.B.C.D | X:X:X:X::X | peer-group peer-group-name ] keepalives [in | out] To disable debugging, use the no debug ip bgp [ A.B.C.D ...

  • Dell 9.8(0.0) - page 399

    Version Description 7.7.1.0 Introduced on the C-Series. Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. Z9500 Syntax debug ip bgp [vrf vrf-name ] [ A.B.C.D | X:X:X:X::X | peer-group peer-gr ...

  • Dell 9.8(0.0) - page 400

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Z9500 Syntax debug i ...

  • Dell 9.8(0.0) - page 401

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. Usage Information This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors. debug ip bgp updates All ...

  • Dell 9.8(0.0) - page 402

    peer-group- name (OPTIONAL) Enter the name of the peer group to disable or enable all routers within the peer group. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell ...

  • Dell 9.8(0.0) - page 403

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The default-metric command in BGP sets the value of the BGP MULTI_EXIT_DISC (MED) attribute for redistri ...

  • Dell 9.8(0.0) - page 404

    description Enter a description of the BGP routing protocol Z9500 Syntax description { description } To remove the description, use the no description { description } command. Parameters description Enter a description to identify the BGP protocol (80 characters maximum). Defaults none Command Modes ROUTER BGP Command History This guide is platform ...

  • Dell 9.8(0.0) - page 405

    Parameters external- distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20 . internal- distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200 . local-distance Enter a number to assign to routes lea ...

  • Dell 9.8(0.0) - page 406

    maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. Z9500 Syntax maximum-paths {ebgp | ibgp} number To return to the default values, enter the no maximum-paths command. Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipa ...

  • Dell 9.8(0.0) - page 407

    neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/Subsequent Address Family Identifier). Z9500 Syntax neighbor [ ip-address | peer-group-name ] activate To disable, use the no neighbor [ ip-address | peer-group-name ] activate command. Parameters ip-address (OPT ...

  • Dell 9.8(0.0) - page 408

    neighbor add-path This command allows the specified neighbor/peer group to send/receive multiple path advertisements. Z9500 Syntax neighbor [ ip-address | peer-group-name ] add-path [send | receive | both] path-count Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group- name (OPTIONAL) Enter the ...

  • Dell 9.8(0.0) - page 409

    neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. Z9500 Syntax neighbor { ip-address | peer-group-name } advertisement-interval seconds To return to the default value, use the no neighbor { ip-address | peer- group-name } advertisement-interval command. Parameters ip-address (OPTIONAL) ...

  • Dell 9.8(0.0) - page 410

    neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting. Z9500 Syntax neighbor { ip-address } advertisement-start seconds To return to the default value, use the no neighbor { ip-address } advertisement-start command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal f ...

  • Dell 9.8(0.0) - page 411

    Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group- name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. number Enter a number of times to allow this neighbor ID to use the AS path. The range is from 1 to 10. Defaults Not configured. Comman ...

  • Dell 9.8(0.0) - page 412

    route-map map-name (OPTIONAL) Enter the keyword route-map then the name of a configured route map. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the De ...

  • Dell 9.8(0.0) - page 413

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 414

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 415

    Command History Version Description 9.7(0.0) Introduced on the S-Series and Z-Series. Usage Information Configuring or un-configuring the command will bring down and bring up the BGP Route Manager, this will result in tear down and re-establishment of all active sessions. Link Bandwidth has to be configured on the router in order to tell it to asso ...

  • Dell 9.8(0.0) - page 416

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information To prevent loops, the neighbor ebgp-multihop command does not install the default routes of the multihop ...

  • Dell 9.8(0.0) - page 417

    Version Description 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information When you enable failover, BGP keeps track of IP or IPv6 ability to reach the peer remote address and the peer local address. Whenever either address becomes unreachable (for example, no active route exists in the routing table for the peer IP or IPv6 destin ...

  • Dell 9.8(0.0) - page 418

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, ACL names were up to 16 characters long. 7.7.1.0 Introduced on the C-Series. Usage Information To enter AS-PATH ACL mode and configure the AS-PATH fil ...

  • Dell 9.8(0.0) - page 419

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 420

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 421

    Defaults threshold = 75 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 422

    Defaults Disabled. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information If you configure the set ipv6 next-hop command in ROUTE-MAP mode, its configuration takes precedence over the neighbor next-hop-self comm ...

  • Dell 9.8(0.0) - page 423

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Configure the same password on both BGP peers or a connection does not occur. When you configure MD5 aut ...

  • Dell 9.8(0.0) - page 424

    peer-group- name Enter the name of a configured peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for th ...

  • Dell 9.8(0.0) - page 425

    show ip bgp neighbors — views BGP neighbors configurations. neighbor peer-group (creating group) Allows you to create a peer group and assign it a name. Z9500 Syntax neighbor peer-group-name peer-group To delete a peer group, use the no neighbor peer-group-name peer-group command. Parameters peer-group- name Enter a text string up to 16 character ...

  • Dell 9.8(0.0) - page 426

    neighbor peer-group passive Enable passive peering on a BGP peer group, that is, the peer group does not send an OPEN message, but responds to one. Z9500 Syntax neighbor peer-group-name peer-group passive [ sessions ] To delete a passive peer-group, use the no neighbor peer-group-name peer-group passive command. Parameters peer-group- name Enter a ...

  • Dell 9.8(0.0) - page 427

    neighbor remote-as — assigns an indirectly connected AS to a neighbor or peer group. neighbor remote-as Create and specify the remote peer to the BGP neighbor. Z9500 Syntax neighbor { ip-address | peer-group-name } remote-as number To delete a remote AS entry, use the no neighbor { ip-address | peer- group-name } remote-as number command. Paramet ...

  • Dell 9.8(0.0) - page 428

    Related Commands router bgp — enters ROUTER BGP mode and configures routes in an AS. bgp four-octet-as-support — enables 4-byte support for the BGP process. neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Z9500 Syntax neighbor { ip-address | peer-group-name } remove-private-as To return to the default, ...

  • Dell 9.8(0.0) - page 429

    If a confederation contains private AS numbers in its AS-PATH, the software removes the private AS numbers only if they follow the confederation numbers in the AS path. Private AS numbers are from 64512 to 65535 (2 byte). neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Z9500 S ...

  • Dell 9.8(0.0) - page 430

    Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted. If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used ...

  • Dell 9.8(0.0) - page 431

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector , the internal BGP (IBGP) ...

  • Dell 9.8(0.0) - page 432

    Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced ...

  • Dell 9.8(0.0) - page 433

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BG ...

  • Dell 9.8(0.0) - page 434

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores ...

  • Dell 9.8(0.0) - page 435

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 In ...

  • Dell 9.8(0.0) - page 436

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Timer values configured with the neighbor timers command override the timer values configured with any o ...

  • Dell 9.8(0.0) - page 437

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Loopback interfaces are up constantly and the BGP session may need one interface constantly up to stabil ...

  • Dell 9.8(0.0) - page 438

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information In the best path selection process, the path with the highest weight value is preferred. NOTE: In the best-path selection process, the path with the highest weight value is preferred. If you configure the se ...

  • Dell 9.8(0.0) - page 439

    • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The fol ...

  • Dell 9.8(0.0) - page 440

    network backdoor Specify this IGP route as the preferred route. Z9500 Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for exampl ...

  • Dell 9.8(0.0) - page 441

    permit bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to permit incoming or outgoing traffic. Syntax permit bandwidth To disable this setting, enter the no permit bandwidth command. Parameters bandwidth Enter the keyword bandwidth to specify extended- community attribute as the matching criter ...

  • Dell 9.8(0.0) - page 442

    • match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, ...

  • Dell 9.8(0.0) - page 443

    When a combination of locally originated and peer originated routes occurs, both these routes will exist in the RTM. However, only the best route is kept active in the RTM and the remaining route is rendered in-active. It is possible to keep only one locally originated route in the BGP database. Network command has preference over the re-distribute ...

  • Dell 9.8(0.0) - page 444

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal . 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information You can use the redistribute command to advertis ...

  • Dell 9.8(0.0) - page 445

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information At least one interface must be in Layer 3 mode for the router bgp command to be accepted. If no interfaces are enabled for Layer 3, an error message appears: % Error: No router id configured Example Dell(con ...

  • Dell 9.8(0.0) - page 446

    show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system. Z9500 Syntax show capture bgp-pdu neighbor ipv4-address Parameters ipv4-address Enter the IPv4 address (in dotted decimal format) of the BGP address to display packet information for that address. Command Modes EXEC Privilege Command History This ...

  • Dell 9.8(0.0) - page 447

    ffffffff ffffffff ffffffff ffffffff 00290104 000100b4 14141401 0c020a01 04000100 01020080 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:50 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] Dell# Related Commands capture bgp-pdu max-buffer-size — specifies a size ...

  • Dell 9.8(0.0) - page 448

    Related Commands capture bgp-pdu max-buffer-size — specifies a size for the capture buffer. show ip bgp View the current BGP IPv4 routing table for the system. Z9500 Syntax show ip bgp [vrf vrf-name ] [ ipv4 unicast ] [network [ network- mask ] [longer-prefixes]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VR ...

  • Dell 9.8(0.0) - page 449

    Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. In BGP, this command displays the exact reason why the route is discarded. The following describes the ...

  • Dell 9.8(0.0) - page 450

    Received from : 1.1.1.2 (3.3.3.1) Best AS_PATH : Next-Hop : 1.1.1.2, Cost : 0 Origin IGP, Metric 0, LocalPref 100, Weight 0, internal Extended Communities : DMZ-Link Bw: 2000 kbytes* Related Commands show ip bgp community — views the BGP communities. neighbor maximum-prefix — controls the number of network prefixes received. show ip bgp cluster ...

  • Dell 9.8(0.0) - page 451

    Version Description 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The following describes the show ip bgp cluster-list command shown in th ...

  • Dell 9.8(0.0) - page 452

    n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>I 55.0.0.0/24 172.16.0.2 0 0 400 500 600 i *>I 66.0.0.0/24 172.16.0.2 0 0 500 i *>I 77.0.0.0/24 172.16.0.2 0 0 i Dell# show ip bgp community View information on all routes with Community attributes or view specific ...

  • Dell 9.8(0.0) - page 453

    All routes with the NO_EXPORT_SUBCONFED (0xFFFFFF03) community attribute must not be advertised to external BGP peers. no-advertise Enter the keywords no-advertise to view all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP pe ...

  • Dell 9.8(0.0) - page 454

    The following describes the show ip bgp community command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s ...

  • Dell 9.8(0.0) - page 455

    *> 66.0.0.0/24 172.16.0.2 0 200 i show ip bgp community-list View routes that a specific community list affects. Z9500 Syntax show ip bgp [vrf vrf-name ] [ipv4 { unicast | multicast } | ipv6 unicast ] community-list community-list-name [exact-match] Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view ro ...

  • Dell 9.8(0.0) - page 456

    Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The show ip bgp community-list command without any parameters lists BGP routes matching the Community List and the output is the same as for the show ip bgp command output. The following describes the show ip bgp community-list pass command ...

  • Dell 9.8(0.0) - page 457

    Communities : 200:1 1000:1 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active). Z9500 Syntax show ip bgp [vrf vrf-name ] [ipv4 { multicast | unicast } | ipv6 unicast ] dampened-paths Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific comm ...

  • Dell 9.8(0.0) - page 458

    Usage Information To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized. T ...

  • Dell 9.8(0.0) - page 459

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 460

    TxUpdCodeP 0x41a1b780 : TrEvt 0 : LocPref 100 : tmpPathP 0x41a1b7b8 : LogNbrChgs 1 RecursiveNH 1 : PgCfgId 0 : KeepAlive 0 : HldTime 0 : DioHdl 0 : AggrValTmrP 0x41ee7024 UpdNetTmrP 0 : RedistTmrP 0x41ee7094 : PeerChgTmrP 0 : CleanRibTmrP 0x41ee7104 PeerUpdTmrP 0x41ee70cc : DfrdNHTmrP 0x41ee7174 : DfrdRtselTmrP 0x41ee713c : FastExtFallover 1 : Fast ...

  • Dell 9.8(0.0) - page 461

    show ip bgp extcommunity-list View information on all routes with Extended Community attributes. Z9500 Syntax show ip bgp [vrf vrf-name ] [ipv4 { multicast | unicast } | ipv6 unicast ] extcommunity-list [ list name ] Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information on all routes with extende ...

  • Dell 9.8(0.0) - page 462

    Usage Information To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found. The show ip bgp community command without any parameters lists BGP routes with at least one BGP community attribute and the output is the same as for the ...

  • Dell 9.8(0.0) - page 463

    ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. as-path-name Enter an AS-PATH access list name. The range is 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, ...

  • Dell 9.8(0.0) - page 464

    Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. Example Dell#show run as-path a1 ! ip as-path access-list a1 permit 500 Dell# Dell#show ip bgp filter-list a1 BGP local RIB : Routes to be Added 0, Repl ...

  • Dell 9.8(0.0) - page 465

    ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. ip-address (OPTIONAL) Enter the IP address (in dotted decimal format) of the BGP network to view information only on that network. mask (OPTIONAL) Enter the network mask (in slash prefix (/x) format) of the BGP net ...

  • Dell 9.8(0.0) - page 466

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The following describes the show ip bgp flap command shown in the following example. Field Description Ne ...

  • Dell 9.8(0.0) - page 467

    show ip bgp inconsistent-as View routes with inconsistent originating autonomous system (AS) numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path. Z9500 Syntax show ip bgp [ ipv4 unicast ] inconsistent-as Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For co ...

  • Dell 9.8(0.0) - page 468

    Path source: I - internal, c - confed-external, r - redistributed, n - network Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 3.0.0.0/8 63.114.8.33 0 18508 209 7018 80 i * 63.114.8.34 0 18508 209 7018 80 i * 63.114.8.60 0 18508 209 7018 80 i *> 63.114.8.33 0 18508 701 80 i *> 3.18.135.0/24 63.114.8 ...

  • Dell 9.8(0.0) - page 469

    ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. ip-address (OPTIONAL) Enter the IP address of the neighbor to view only BGP information exchanged with that neighbor. advertised- routes (OPTIONAL) Enter the keywords advertised-routes to view only the routes the n ...

  • Dell 9.8(0.0) - page 470

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Added the detail option. Output now displays the default MED value. 7.2.1.0 Added the ...

  • Dell 9.8(0.0) - page 471

    The Lines Beginning with: Description • keepalive interval is the number of seconds between keepalive messages to help ensure that the TCP session is still alive. Received messages This line displays the number of BGP messages received, the number of notifications (error messages), and the number of messages waiting in a queue for processing. Sen ...

  • Dell 9.8(0.0) - page 472

    Example Dell#show ip bgp neighbors 172.16.0.2 BGP neighbor is 172.16.0.2, remote AS 200, external link Member of peer-group port0 for session parameters BGP remote router ID 172.16.0.2 BGP state ESTABLISHED, in this state for 00:13:55 Last read 00:00:03, Last write 00:00:55 Hold time is 180, keepalive interval is 60 seconds Received 50 messages, 0 ...

  • Dell 9.8(0.0) - page 473

    show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. Z9500 Syntax show ip bgp [vrf vrf-name ] next-hop Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For comm ...

  • Dell 9.8(0.0) - page 474

    Example Dell# show ip bgp next-hop Next-hop Resolved 172.16.0.2 YES Dell# show ip bgp paths View all the BGP path attributes in the BGP database. Z9500 Syntax show ip bgp paths [regexp regular-expression ] Parameters regexp regular- expression Enter a regular expression then use one or a combination of the following characters to match: • . = (pe ...

  • Dell 9.8(0.0) - page 475

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The following describes the show ip bgp path command shown in the following example. Field Description Total Displays the total number of BGP path attributes. Address Displa ...

  • Dell 9.8(0.0) - page 476

    show ip bgp paths as-path View all unique AS-PATHs in the BGP database. Z9500 Syntax show ip bgp paths as-path Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of th ...

  • Dell 9.8(0.0) - page 477

    0x1ea3c17c 763 1 12 0x1ea3c2cc 763 1 32 0x1ea3c09c 764 1 {72 73} 0x1ea3c0d4 764 1 {82 83} 0x1ea3c224 1019 1 43 0x1ea3c294 1019 1 23 0x1ea3c02c 1021 4 Dell# show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Z9500 Syntax show ip bgp [vrf vrf-name ] paths community Command Modes • EXEC • EXEC Privilege Command Hist ...

  • Dell 9.8(0.0) - page 478

    Field Description Community Displays the community attributes in this BGP path. Example Dell#show ip bgp paths community Total 2 communities Refcount Community 1 NO-ADVERTISE 1 200:1 1000:1 3000:1 show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Z9500 Syntax show ip bgp [vrf vrf-name ] [ipv4 { multicast | unic ...

  • Dell 9.8(0.0) - page 479

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. Introduced on S ...

  • Dell 9.8(0.0) - page 480

    Number of peers in this group 1 Maximum limit on the accepted connections 256 Peer-group members (* - outbound optimized): 172.16.0.2 Dell# Related Commands neighbor peer-group (assigning peers) — assigns a peer to a peer-group. neighbor peer-group (creating group) — creates a peer group. show ip bgp regexp Display the subset of the BGP routing ...

  • Dell 9.8(0.0) - page 481

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–O ...

  • Dell 9.8(0.0) - page 482

    172.16.0.2 0 200 i *> 66.0.0.0/24 172.16.0.2 0 200 i show ip bgp summary Allows you to view the status of all BGP connections. Z9500 Syntax show ip bgp [vrf vrf-name ] [ipv4 { multicast | unicast } | ipv6 unicast ] summary Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view the status of all BGP connecti ...

  • Dell 9.8(0.0) - page 483

    Usage Information In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes. For example, if cluster_id is an attribute associated ...

  • Dell 9.8(0.0) - page 484

    Field Description MsgRcvd Displays the number of BGP messages that neighbor received. MsgSent Displays the number of BGP messages that neighbor sent. TblVer Displays the version of the BGP table that was sent to that neighbor. InQ Displays the number of messages from that neighbor waiting to be processed. OutQ Displays the number of messages waitin ...

  • Dell 9.8(0.0) - page 485

    2 BGP path attribute entrie(s) using 144 bytes of memory 1 BGP AS-PATH entrie(s) using 10 bytes of memory 2 neighbor(s) using 16384 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 172.16.0.2 200 10 8 0 0 0 00:05:34 2 192.168.10.2 100 0 22 0 0 0 00:00:00 (shut) Dell# show running-config bgp To display the current BGP co ...

  • Dell 9.8(0.0) - page 486

    Parameters keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds . holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The defau ...

  • Dell 9.8(0.0) - page 487

    Dell Networking OS Version Platform Support 7.8.1.0, MBGP for IPv4 Multicast Only S-Series 8.2.1.0, MBGP E-Series ExaScale debug ip bgp dampening View information on routes being dampened. Z9500 Syntax debug ip bgp [vrf vrf-name ] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. ...

  • Dell 9.8(0.0) - page 488

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced IPv6 MGBP support for the E-Series. distance bgp Configure three administrative distances for routes. Z9500 Syntax distance bgp external-distance internal-distance local-distance To return to default values ...

  • Dell 9.8(0.0) - page 489

    Version Description 7.7.1.0 Introduced on the C-Series. Usage Information CAUTION: Dell Networking recommends not changing the administrative distance of internal routes. Changing the administrative distances may cause routing table inconsistencies. The higher the administrative distance assigned to a route means that your confidence in that route ...

  • Dell 9.8(0.0) - page 490

    Version Description 9.4(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information To determine a BGP session flap, both a route-down event and a subsequent ...

  • Dell 9.8(0.0) - page 491

    BGP Extended Communities (RFC 4360) BGP Extended Communities, as defined in RFC 4360, is an optional transitive BGP attribute. BGP Extended Communities provides two major advantages over Standard Communities: • The range is extended from 4-octet (AA:NN) to 8-octet (Type:Value) to provide enough number communities. • Communities are structured u ...

  • Dell 9.8(0.0) - page 492

    Version Description 9.2(1.0) Introduced on the Z9500. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Related Commands permit — configures to add (permit) rules. show ip extcommunity-list — displays the extended community list. deny regex This feature allows you to specify an extended ...

  • Dell 9.8(0.0) - page 493

    Related Commands permit regex — permits a community using a regular expression. description To designate a meaningful description to the extended community, use this feature. Z9500 Syntax description { line } To remove the description, use the no description { line } command. Parameters line Enter a description (maximum 80 characters). Defaults N ...

  • Dell 9.8(0.0) - page 494

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 ...

  • Dell 9.8(0.0) - page 495

    Version Description 7.6.1.0 Introduced on the E-Series. Usage Information Like standard communities, you can use extended communities in the route-map to match the attribute. Example Dell(config-route-map)#match extcommunity Freedombird Dell(config-route-map)# permit To add rules (permit) from the two types of extended communities, Route Origin (rt ...

  • Dell 9.8(0.0) - page 496

    Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Related Commands deny — configures to delete (deny) rules. show ip bgp extcommunity-list — displays the extended community list. permit regex This feature allows you specify an extended community to forward (permit) us ...

  • Dell 9.8(0.0) - page 497

    set extcommunity rt To set Route Origin community attributes in Route Map, use this feature. Z9500 Syntax set extcommunity rt {as4 ASN4:NN [non-trans] | ASN:NNNN [non- trans] | IPADDR:NN [non-trans]} [additive] To delete the Route Origin community, use the no set extcommunity command. Parameters as4 ASN4:NN Enter the keyword as4 then the 4-octet AS ...

  • Dell 9.8(0.0) - page 498

    Usage Information If the set community rt and soo are in the same route-map entry, the behavior defines as: • If the rt option comes before soo , with or without the additive option, soo overrides the communities rt sets. • If the rt option comes after soo , without the additive option, rt overrides the communities soo sets. • If the rt with ...

  • Dell 9.8(0.0) - page 499

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Usage Information If the set community rt and soo are in the same route-map entry, the ...

  • Dell 9.8(0.0) - page 500

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 ...

  • Dell 9.8(0.0) - page 501

    show ip bgp paths extcommunity To display all BGP paths having extended community attributes, use this feature. Z9500 Syntax show ip bgp paths extcommunity Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Re ...

  • Dell 9.8(0.0) - page 502

    show ip extcommunity-list Display the IP extended community list. Z9500 Syntax show ip extcommunity-list [ word ] Parameters word Enter the name of the extended community list you want to view. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relev ...

  • Dell 9.8(0.0) - page 503

    Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 7 ...

  • Dell 9.8(0.0) - page 504

    Defaults Not configured. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 6.5.1.0 Introduced Usage Information Enter ipv6unicast to enter the BGP for IPv6 mode (CONF-ROUTER_BGPv6_AF). address family ipv6 unicast This command changes the context to subsequent address family identifier (SAFI). Z9500 Synta ...

  • Dell 9.8(0.0) - page 505

    aggregate-address Summarize a range of prefixes to minimize the number of entries in the routing table. Z9500 Syntax aggregate-address ipv6-address prefix-length [advertise-map map-name ] [as-set] [attribute-map map-name ] [summary-only] [suppress-map map-name ] Parameters ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format f ...

  • Dell 9.8(0.0) - page 506

    Usage Information At least one of the routes included in the aggregate address must be in the BGP routing table for the configured aggregate to become active. Do not add the as-set parameter to the aggregate if routes within the aggregate are constantly changing as the aggregate will flap to keep track of the changes in the AS_PATH. In route maps u ...

  • Dell 9.8(0.0) - page 507

    If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations. Z9500 Syntax bgp bestpath as-path ignore To return to the default, use the no bgp bestpath as-path ignore command. Defaults Disabled (that is, the software considers the AS_PATH when ch ...

  • Dell 9.8(0.0) - page 508

    Version Description 7.4.1.0 Introduced Usage Information The software compares the MEDs only if the path contains no external autonomous system numbers. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath med missing-as-best During path selection, indicate preference to paths with missing MED (MULTI_E ...

  • Dell 9.8(0.0) - page 509

    Defaults Enabled when a route reflector is configured. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information Route reflection to clients is not necessary if all client routers are fully meshed. Related Commands • bgp cluster- ...

  • Dell 9.8(0.0) - page 510

    Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster. The default format for displaying the cluster-id is dotted decimal, but if you enter the cluster-id as an integer, it is displayed as an integer. Related Commands • bgp client-to-client reflection – enables route reflecti ...

  • Dell 9.8(0.0) - page 511

    bgp dampening Enable BGP route dampening and configure the dampening parameters. Z9500 Syntax bgp dampening [ half-life reuse suppress max-suppress-time ] [route-map map-name ] To disable route dampening, use the no bgp dampening [ half-life reuse suppress max-suppress-time ] [route-map map-name ] command. Parameters half-life (OPTIONAL) Enter the ...

  • Dell 9.8(0.0) - page 512

    Usage Information If you enter bgp dampening , the default values for half-life , reuse , suppress , and max-suppress-time are applied. The parameters are position- dependent; therefore, if you configure one parameter, you must configure the parameters in the order they appear in the command. Related Commands show ip bgp dampened-paths – views th ...

  • Dell 9.8(0.0) - page 513

    Defaults Enabled. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information This is enabled by default, that is for all updates received from EBGP peers, BGP ensures that the first AS of the first AS segment is always the AS of the ...

  • Dell 9.8(0.0) - page 514

    bgp four-octet-as-support Enable 4-byte support for the BGP process. Z9500 Syntax bgp four-octet-as-support To disable fast external fallover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2-Byte format). Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on ...

  • Dell 9.8(0.0) - page 515

    Parameters neighbor ip- address | peer- group-name Enter the keyword neighbor followed by one of the options listed below: • ip-address of the neighbor in IP address format of the neighbor. • peer-group-name of the neighbor peer group. restart-time seconds Enter the keywords restart-time followed by the maximum number of seconds needed to resta ...

  • Dell 9.8(0.0) - page 516

    Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information The bgp log-neighbor-changes command appears in the show config command output. Related Commands show config – views the current configuration. bgp non-deterministic-med Compare MEDs of paths from ...

  • Dell 9.8(0.0) - page 517

    bgp recursive-bgp-next-hop Enable next-hop resolution through other routes learned by BGP. Z9500 Syntax bgp recursive-bgp-next-hop To disable next-hop resolution, use the no bgp recursive-bgp-next-hop command. Defaults Enabled. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E ...

  • Dell 9.8(0.0) - page 518

    Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced Usage Information BGP uses regular expressions (regex) to filter route information. In particular, the use of regular expressions to filter routes based on AS-PATHs and communities is quite common. In a large scale c ...

  • Dell 9.8(0.0) - page 519

    Version Description 7.4.1.0 Introduced Usage Information Peering sessions are reset when you change the router ID of a BGP router. bgp soft-reconfig-backup To avoid the peer from resending messages, use this command only when route-refresh is not negotiated. Z9500 Syntax bgp soft-reconfig-backup To return to the default setting, use the no bgp soft ...

  • Dell 9.8(0.0) - page 520

    Related Commands clear ip bgp — activates inbound policies without resetting the BGP TCP session. capture bgp-pdu max-buffer-size Set the size of the BGP packet capture buffer. This buffer size pertains to both IPv4 and IPv6 addresses. Z9500 Syntax capture bgp-pdu max-buffer-size 100-102400000 Parameters 100-10240000 0 Enter a size for the captur ...

  • Dell 9.8(0.0) - page 521

    Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced Related Commands • clear ip bgp – enables route reflection between route reflector and clients. • show capture bgp-pdu neighbor – configures ...

  • Dell 9.8(0.0) - page 522

    soft (OPTIONAL) Enter the keyword soft to configure and activate policies without resetting the BGP TCP session, that is, BGP Soft Reconfiguration. NOTE: If you enter clear ip bgp ip6-address soft , both inbound and outbound policies are reset. in (OPTIONAL) Enter the keyword in to activate only inbound policies. out (OPTIONAL) Enter the keyword ou ...

  • Dell 9.8(0.0) - page 523

    Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced clear ip bgp as-number Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection. Z9500 Syntax clear ip bgp as-number [fla ...

  • Dell 9.8(0.0) - page 524

    Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced clear ip bgp ipv6 dampening Clear information on route dampening and return suppressed route to active state. Z9500 Syntax clear ip bgp ipv6 unicast dampening [ ipv6-address ] Parameters ...

  • Dell 9.8(0.0) - page 525

    NOTE: The :: notation specifies successive hexadecimal fields of zeros. filter-list as- path-name (OPTIONAL) Enter the keywords filter-list followed by the name of a configured AS-PATH list. regexp regular- expression (OPTIONAL) Enter the keyword regexp followed by regular expressions. Use one or a combination of the following: . (period) matches o ...

  • Dell 9.8(0.0) - page 526

    clear ip bgp ipv6 unicast Reset MBGP sessions. Z9500 Syntax clear ip bgp ipv6 unicast * ipv6-address prefix-length [dampening | flap-statistics] peer-group] Parameters * Enter the character * to clear all peers. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 ...

  • Dell 9.8(0.0) - page 527

    Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 7.4.1.0 Introduced clear ip bgp ipv6 unicast flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap. Z9500 Syntax clear ip bgp ipv6 unicast flap-statistics [ network | filter- list list |regexp regexp ] ...

  • Dell 9.8(0.0) - page 528

    Version Description 7.4.1.0 Introduced debug ip bgp keepalives Allows you to view information about BGP keepalive messages. Z9500 Syntax debug ip bgp [ ipv6-address | peer-group peer-group-name ] keepalives [in | out] To disable debugging, use the no debug ip bgp [ ip-address | peer-group peer-group-name ] keepalives [in | out] command. Parameters ...

  • Dell 9.8(0.0) - page 529

    debug ip bgp ipv6 dampening View information on IPv6 routes being dampened. Z9500 Syntax debug ip bgp ipv6 unicast dampening [in | out] To disable debugging, use the no debug ip bgp ipv6 unicast dampening command. Parameters in (OPTIONAL) Enter the keyword in to view only information on inbound dampened routes. out (OPTIONAL) Enter the keyword out ...

  • Dell 9.8(0.0) - page 530

    updates Enter the keyword updates to view BGP update information. in (OPTIONAL) Enter the keyword in to view only BGP updates received from neighbors. out (OPTIONAL) Enter the keyword out to view only BGP updates sent to neighbors. Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 7.4.1.0 Introduced ...

  • Dell 9.8(0.0) - page 531

    To disable debugging, use the no debug ip bgp ipv6 unicast ipv6- address prefix-length updates [in | out] command. Parameters ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. upda ...

  • Dell 9.8(0.0) - page 532

    in (OPTIONAL) Enter the keyword in to view BGP notifications received from neighbors. out (OPTIONAL) Enter the keyword out to view BGP notifications sent to neighbors. Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information E ...

  • Dell 9.8(0.0) - page 533

    Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information Enter the no debug ip bgp command to remove all configured debug commands for BGP. default-metric Allows you to change the metrics of redistributed routes to locally ori ...

  • Dell 9.8(0.0) - page 534

    description Enter a description of the BGP routing protocol. Z9500 Syntax description { description } To remove the description, use the no description { description } command. Parameters description Enter a description to identify the BGP protocol (80 characters maximum). Defaults none Command Modes ROUTER BGP Command History Version Description 9 ...

  • Dell 9.8(0.0) - page 535

    Defaults • external-distance = 20 • internal-distance = 200 • local-distance = 200 Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information CAUTION: Dell Networking recommends that you do not change the admi ...

  • Dell 9.8(0.0) - page 536

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Related Commands show ipv6 prefix-list — View the selected IPv6 prefix-list. maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. Z9500 Syntax maximu ...

  • Dell 9.8(0.0) - page 537

    neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI. Z9500 Syntax neighbor { ipv6-address | peer-group-name } activate To disable, use the no neighbor { ipv6-address | peer-group-name } activate command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: n ...

  • Dell 9.8(0.0) - page 538

    Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-group- name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. seconds Enter a number as the time interval, in seconds, between BGP advertisements. T ...

  • Dell 9.8(0.0) - page 539

    Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Related Commands bgp four-octet-as-support – enables 4-Byte support for the BGP process. neighbor default-originate Inject the default route to a BGP peer or neighbor. Z9500 Syntax neighbor ...

  • Dell 9.8(0.0) - page 540

    neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). Z9500 Syntax neighbor { ipv6-address | peer-group-name } description text To delete a description, use the no neighbor { ipv6-address | peer-group- name } description text command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x: ...

  • Dell 9.8(0.0) - page 541

    peer-group- name Enter the name of the peer group. prefix-list- name Enter the name of an established prefix list. If you do not configure the prefix list, the default is permit (to allow all routes). in Enter the keyword in to distribute only inbound traffic. out Enter the keyword out to distribute only outbound traffic. Defaults Not configured. C ...

  • Dell 9.8(0.0) - page 542

    Defaults Disabled. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information To prevent loops, the neighbor ebgp-multihop command does not install default routes of the multihop peer. Networks not directly connected are not conside ...

  • Dell 9.8(0.0) - page 543

    Related Commands show ip bgp neighbors – displays information on the BGP neighbors. neighbor filter-list Configure a BGP filter based on the AS-PATH attribute. Z9500 Syntax neighbor { ipv6-address | peer-group-name } filter-list as-path- name {in | out} To delete a BGP filter, use the no neighbor { ipv6-address | peer-group- name } filter-list as ...

  • Dell 9.8(0.0) - page 544

    To return to the default values, use the no neighbor { ipv6-address | peer- group-name } maximum-prefix maximum [ threshold ] [warning-only] command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-group- name Enter the name of the peer group. maxi ...

  • Dell 9.8(0.0) - page 545

    neighbor next-hop-self Allows you to configure the router as the next hop for a BGP neighbor. (This command is used for IBGP). Z9500 Syntax neighbor { ipv6-address | peer-group-name } next-hop-self To return to the default setting, use the no neighbor { ipv6-address | peer- group-name } next-hop-self command. Parameters ipv6-address Enter the IPv6 ...

  • Dell 9.8(0.0) - page 546

    peer-group peer-group- name Enter the keywords peer-group followed by the name of a configured peer group. The maximum is 16 characters. Defaults Not configured. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information You can ass ...

  • Dell 9.8(0.0) - page 547

    To delete a peer group, use the no neighbor peer-group-name peer-group command. Parameters peer-group- name Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7 ...

  • Dell 9.8(0.0) - page 548

    Version Description 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information After you configure a peer group as passive, you must assign it a subnet using the neighbor subnet command. Related Commands neighbor subnet – assigns a subnet to a dynamically-configured BGP neighbor. neighbor remote-as Create and specify the re ...

  • Dell 9.8(0.0) - page 549

    Related Commands router bgp – Enter ROUTER BGP mode and configure routes in an AS. neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Z9500 Syntax neighbor { ipv6-address | peer-group-name } remove-private-as To return to the default, use the no neighbor { ipv6-address | peer- group-name } remove-private-as ...

  • Dell 9.8(0.0) - page 550

    neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Z9500 Syntax neighbor { ipv6-address | peer-group-name } route-map map-name {in | out} To remove the route map, use the no neighbor { ipv6-address | peer- group-name } route-map map-name {in | out} command. Parameters ipv6-addres ...

  • Dell 9.8(0.0) - page 551

    neighbor route-reflector-client Configure a neighbor as a member of a route reflector cluster. Z9500 Syntax neighbor { ipv6-address | peer-group-name } route-reflector- client To indicate that the neighbor is not a route reflector client or to delete a route reflector configuration, use the no neighbor { ipv6-address | peer-group- name } route-refl ...

  • Dell 9.8(0.0) - page 552

    To disable sending a COMMUNITY attribute, use the no neighbor { ipv6- address | peer-group-name } send-community command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-group- name Enter the name of the peer group to send a COMMUNITY attribute to ...

  • Dell 9.8(0.0) - page 553

    Version Description 9.2(1.0) Introduced on the Z9500. 8.4.1.0 Added support for IPv4 multicast and IPv4 unicast address families. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information This command enables soft-reconfiguration for the specified BGP neighbor. BGP s ...

  • Dell 9.8(0.0) - page 554

    neighbor shutdown Disable a BGP neighbor or peer group. Z9500 Syntax neighbor { ipv6-address | peer-group-name } shutdown To enable a disabled neighbor or peer group, use the no neighbor { ipv6- address | peer-group-name } shutdown command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies succ ...

  • Dell 9.8(0.0) - page 555

    neighbor timers Set keepalive and hold time timers for a BGP neighbor or a peer group. Z9500 Syntax neighbor { ipv6-address | peer-group-name } timers keepalive holdtime To return to the default values, use the no neighbor { ipv6-address | peer- group-name } timers command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NO ...

  • Dell 9.8(0.0) - page 556

    • whichever is the lower value; one-third of the new holdtime value, or the configured keepalive value is the new keepalive value. neighbor update-source Enable the software to use Loopback interfaces for TCP connections for BGP sessions. Z9500 Syntax neighbor { ipv6-address | peer-group-name } update-source loopback interface To use the closest ...

  • Dell 9.8(0.0) - page 557

    To remove a weight value, use the no neighbor { ipv6-address | peer- group-name } weight weight command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-group- name Enter the name of the peer group to disable all routers within the peer group. weig ...

  • Dell 9.8(0.0) - page 558

    Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced Usage Information The TCP session is authentication and hence prevents the data from being compromised. network Specify the networks for the BGP process and enter them in the BGP routing table. Z9500 Syntax network ipv6-address prefix-length [route-map map-name ...

  • Dell 9.8(0.0) - page 559

    Version Description 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced Usage Information The software resolves the network address configured by the network command with the routes in the main routing table to ensure that the networks are reachable via non-BGP routes and non-default routes. Related Commands redistribute – redistribut ...

  • Dell 9.8(0.0) - page 560

    redistribute Redistribute routes into BGP. Z9500 Syntax redistribute {connected | static} [route-map map-name ] To disable redistribution, use the no redistribution [connected | static] [route-map map-name ] command. Parameters connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keywor ...

  • Dell 9.8(0.0) - page 561

    Related Commands neighbor default-originate – injects the default route. redistribute ospf Redistribute OSPFv3 routes into BGP. Z9500 Syntax redistribute ospf process-id [[match external {1 | 2}] [match internal]] [route-map map-name ] To stop redistribution of OSPF routes, use the no redistribute ospf process-id command. Parameters process-id En ...

  • Dell 9.8(0.0) - page 562

    Usage Information When you enter the redistribute ospf process-id command without any other parameters, the software redistributes all OSPF internal routes, external type 1 routes, and external type 2 routes. router bgp Enter ROUTER BGP mode to configure and enable BGP. Z9500 Syntax router bgp as-number To disable BGP, use the no router bgp as-numb ...

  • Dell 9.8(0.0) - page 563

    Version Description 7.5.1.0 Introduced Related Commands • capture bgp-pdu neighbor – enables capture of an IPv6 BGP neighbor packet. • clear ip bgp – specifies a size for the capture buffer. show config View the current ROUTER BGP configuration. Z9500 Syntax show config Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History Version Descr ...

  • Dell 9.8(0.0) - page 564

    show ip bgp next-hop View all next hops (via learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. Z9500 Syntax show ip bgp next-hop [local-routes] Parameters local-routes (OPTIONAL) Show next-hop information for local routes. Command Modes • EXEC ...

  • Dell 9.8(0.0) - page 565

    • ? = (question mark) sequences in a pattern (either 0 or 1 sequences). You must enter an escape sequence (CTRL +v) prior to entering the ? regular expression. • [ ] = (brackets) a range of single-character patterns. • ^ = (caret) the beginning of the input string. If the caret is used at the beginning of a sequence or range, it matches on ev ...

  • Dell 9.8(0.0) - page 566

    Command Modes • EXEC • EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced show ip bgp paths extcommunity View all unique Extended community information in the BGP database. Z9500 Syntax show ip bgp paths extcommunity Command Modes • EXEC • EXEC ...

  • Dell 9.8(0.0) - page 567

    NOTE: You must enter an escape sequence (CTRL+v) prior to entering the ? regular expression. • [ ] = (brackets) a range of single-character patterns. • ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. • $ = (dollar sign) the end ...

  • Dell 9.8(0.0) - page 568

    Related Commands ipv6 prefix-list — configures an IPv6 prefix-list. show ip bgp ipv6 unicast View the current BGP routing table. Z9500 Syntax show ip bgp ipv6 unicast [ network [ network-mask ] [longer- prefixes]] Parameters network (OPTIONAL) Enter the network address (in dotted decimal format) of the BGP network to view information only on that ...

  • Dell 9.8(0.0) - page 569

    Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced show ip bgp ipv6 unicast community View information on all routes with Community attributes or view specific BGP community groups. Z9500 Syntax show ip bgp ipv6 unicast community [ community-number ] [local- as] [no- ...

  • Dell 9.8(0.0) - page 570

    Usage Information To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found. show ip bgp ipv6 unicast community-list View routes that are affected by a specific community list. Z9500 Syntax show ip bgp ipv6 unicast community-list c ...

  • Dell 9.8(0.0) - page 571

    show ip bgp ipv6 unicast detail Display BGP internal information for IPv6 Unicast address family. Z9500 Syntax show ip bgp ipv6 unicast detail Defaults none Command Modes • EXEC • EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced show ip bgp ipv6 ...

  • Dell 9.8(0.0) - page 572

    The show ip bgp community command without any parameters lists BGP routes with at least one BGP community attribute and the output is the same as for the show ip bgp command output. show ip bgp ipv6 unicast filter-list View the routes that match the filter lists. Z9500 Syntax show ip bgp ipv6 unicast filter-list as-path-name Parameters as-path-name ...

  • Dell 9.8(0.0) - page 573

    • * = (asterisk) the sequences in a pattern (0 or more sequences). • + = (plus) the sequences in a pattern (1 or more sequences). • ? = (question mark) sequences in a pattern (either 0 or 1 sequences). NOTE: You must enter an escape sequence (CTRL+v) prior to entering the ? regular expression. • [ ] = (brackets) a range of single-character ...

  • Dell 9.8(0.0) - page 574

    show ip bgp ipv6 unicast neighbors Allows you to view the information exchanged by BGP neighbors. Z9500 Syntax show ip bgp ipv6 unicast neighbors [ ipv6-address prefix-length | ip-address ] [advertised-routes | dampened-routes | detail | flap-statistics | routes] Parameters ipv6-address prefix-length | ip-address Enter the IPv6 address in the x:x:x ...

  • Dell 9.8(0.0) - page 575

    show ip bgp ipv6 unicast peer-group Allows you to view information on the BGP peers in a peer group. Z9500 Syntax show ip bgp ipv6 unicast peer-group [ peer-group-name [summary]] Parameters peer-group- name (OPTIONAL) Enter the name of a peer group to view information about that peer group only. detail (OPTIONAL) Enter the keyword detail to view pe ...

  • Dell 9.8(0.0) - page 576

    show ip bgp ipv6 unicast summary Allows you to view the status of all BGP connections. Z9500 Syntax show ip bgp ipv6 unicast summary Command Modes • EXEC • EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.2.1.0 Introduced on the E-Series ExaScale. Example Dell# show ip bgp summary BGP router identifier 55.5 ...

  • Dell 9.8(0.0) - page 577

    timers bgp Allows you to adjust the BGP network timers for all neighbors. Z9500 Syntax timers bgp keepalive holdtimer To return to the default values, use the no timers bgp command. Parameters keepalive Enter the time interval in seconds between which the software sends keepalive messages. The range is 1 to 65535. The default is 60 seconds . holdti ...

  • Dell 9.8(0.0) - page 578

    show ipv6 mbgproutes Display the selected IPv6 MBGP route or a summary of all MBGP routes in the table. Z9500 Syntax show ipv6 mbgproutes ipv6-address prefix-length | summary Parameters ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: T ...

  • Dell 9.8(0.0) - page 579

    9 Content Addressable Memory (CAM) You can use Content Addressable Memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell N ...

  • Dell 9.8(0.0) - page 580

    cam-acl (Configuration) Select the default CAM allocation settings or reconfigure a new CAM allocation for Layer 2, IPv4, and IPv6 ACLs, Layer 2 and Layer 3 (IPv4) QoS, Layer 2 Protocol Tunneling (L2PT), IP and MAC source address validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR). Z9500 ...

  • Dell 9.8(0.0) - page 581

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added the keyword nlbclusteracl . 9.2(1.0 ...

  • Dell 9.8(0.0) - page 582

    cam-acl-egress Allocate CAM for egress ACLs. Z9500 Syntax cam-acl-egress default | l2acl number ipv4acl number ipv6acl number } Parameters default Reset egress CAM ACL entries to default settings. l2acl number ipv4acl number ipv6acl number Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The ...

  • Dell 9.8(0.0) - page 583

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 584

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. Usage Information The display reflects the settings implemented with the cam-acl command. Example Dell#show cam-acl -- Chassis Cam ACL -- Current Settings(in block sizes) 1 block = 256 entries ...

  • Dell 9.8(0.0) - page 585

    L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 2 -- linecard 2 -- Current Settings(in block sizes) 1 block = 256 entries L2Acl : 4 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p ...

  • Dell 9.8(0.0) - page 586

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 587

    | 1 | Allowed (408) 1 | 0 | IPv4Flow | 408 | 1 | Allowed (408) 1 | 1 | IPv4Flow | 408 | 1 | Allowed (408) 1 | 2 | IPv4Flow | 408 | 1 | Allowed (408) 1 | 3 | IPv4Flow | 408 | 1 | Allowed (408) 2 | 0 | IPv4Flow | 408 | 1 | Allowed (408) 2 | 1 | IPv4Flow | 408 | 1 | Allowed (408) 2 | 2 | IPv4Flow | 408 | 1 | Allowed (408) 2 | 3 | IPv4Flow | 408 | 1 | ...

  • Dell 9.8(0.0) - page 588

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9 ...

  • Dell 9.8(0.0) - page 589

    10 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level. On the Z9500 ...

  • Dell 9.8(0.0) - page 590

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information There are three line cards (0-2) with fixed ports on the Z9500. Line card 0 uses three sets of ports (port pipes): 0 to 2; line cards 1 and 2 use four sets of ports: 0 to 3. ? ...

  • Dell 9.8(0.0) - page 591

    • Queues 8 to 15 process packets destined to the Route Processor CPU. • Queues 16 to 23 process packets destined to the line card CPU. Defaults Clear per-queue rate-limiting counters for all control-plane and port traffic. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms ...

  • Dell 9.8(0.0) - page 592

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. service-policy rate-limit-cpu-queues cpu-qos Apply a QoS input policy-map that rate-limits traffic on control-plane queues. Z9500 Syntax service-policy rate-limit-cpu-queues policy-name cpu-qos ...

  • Dell 9.8(0.0) - page 593

    Related Commands qos-policy-input cpu-qos — creates a QoS input-policy map for CoPP. policy-map-input cpu-qos — creates an input-policy map for CoPP. service-policy rate-limit-protocols cpu-qos Apply a QoS input policy-map that rate-limits protocol traffic on the control plane. Z9500 Syntax service-policy rate-limit-protocols policy-name cpu-qo ...

  • Dell 9.8(0.0) - page 594

    Related Commands ip access-list extended cpu-qos — creates an extended IP ACL for CoPP. mac access-list extended cpu-qos — creates an extended MAC ACL for CoPP. class-map cpu-qos — creates a QoS class map for CoPP. qos-policy-input cpu-qos — creates a QoS input-policy map for CoPP. policy-map-input cpu-qos — creates an input-policy map fo ...

  • Dell 9.8(0.0) - page 595

    applied. TxBytes displays the number of bytes transmitted to a control-plane CPU after protocol-based rate limiting is applied. Drops displays the number of bytes of control-plane traffic that have been dropped as a result of protocol-based rate limiting. The number of RxBytes is calculated as: Drops/< packet-size > + TxBytes/< packet- siz ...

  • Dell 9.8(0.0) - page 596

    PIM 0 0 0 NTP 0 0 0 MULTICAST CATCH ALL 0 0 0 v6 MULTICAST CATCH ALL 0 0 0 DHCP RELAY/DHCP 0 0 0 v6 ICMP NA/v6 ICMP RA 0 0 0 v6 ICMP NS/v6 ICMP RS 0 0 0 v6 ICMP/ICMP 0 0 0 MLD 0 0 0 MSDP 0 0 0 FTP/TELNET/SSH/ L3 LOCAL TERMINATED 0 0 0 L3 UNKNOWN/UNRESOLVED ARP 0 0 0 iSCSI 0 0 0 FCoE 0 0 0 SFLOW 0 0 0 VLT CTRL/VLT IPM PDU 0 0 0 HYPERPULL 0 0 0 OPENF ...

  • Dell 9.8(0.0) - page 597

    Parameters all Enter the keyword all to display counters for rate-limited traffic on all CPU queues, including Route Processor, Control Processor, and line-card CPUs. queue-id queue-number Enter the queue number to display counters for rate-limited traffic on a specified CPU queue. The range of queue- number values is from 0 to 23. The twenty-four ...

  • Dell 9.8(0.0) - page 598

    Q0 5000 5000 0 Dell# show cpu-queue rate Display the rates for each control-plane queue. Z9500 Syntax show cpu-queue rate [all | queue-id queue-number | range from_queue to_queue ] Parameters all Display the rate for all control-plane queues (CPU queues 0– 23). queue-id queue-number Display the rate for a specified control-plane queue. The range ...

  • Dell 9.8(0.0) - page 599

    Q15 12450 4000 Q16 1 100 Q17 1 100 Q18 1 100 Q19 1 100 Q20 600 1000 Q21 7000 7000 Q22 800 1000 Q23 5000 5000 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for thi ...

  • Dell 9.8(0.0) - page 600

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Example Dell#show ip protocol-queue-mapping Protocol Src-Port Dst-Port TcpFlag Queue EgPort Rate (kbps) -------- -------- -------- ------- ----- ------ ----------- TCP (BGP) any/179 179/any _ Q1 ...

  • Dell 9.8(0.0) - page 601

    Command Modes EXEC Privilege Usage Information The show output displays information CPU traffic flows for supported IPv6 protocols, including the ingress queue at which the traffic is queued and the CPU to which protocol traffic is sent with the applied rate limits (configured or default) in kilobits per second (kbps). The egress port queues on CPU ...

  • Dell 9.8(0.0) - page 602

    show mac protocol-queue-mapping Display the Z9500 CPU queue mapping for MAC protocols. Z9500 Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guid ...

  • Dell 9.8(0.0) - page 603

    show protocol-queue-mapping Display the Z9500 protocol-queue mapping for each configured protocol. Z9500 Syntax show protocol-queue-mapping [queue-id queue-number ] Parameters queue-id queue-number (Optional) Display the protocol-queue mapping for a specified control-plane queue. The range of CPU queue numbers is from 0 to 23. Defaults Not configur ...

  • Dell 9.8(0.0) - page 604

    GVRP Q14 RP 200 200 1000 1000 FRRP Q22 LP 300 300 1000 1000 ECFM Q15 RP 150 150 1000 1000 ISIS Q15 RP 500 500 3000 3000 L2PT Q15 RP 150 150 1000 1000 v6 BGP Q15 RP 2500 2500 2000 2000 v6 OSPF Q15 RP 2500 2500 2000 2000 v6 VRRP Q15 RP 400 400 2000 2000 MLD Q14 RP 150 150 500 500 v6 MULTICAST Q9 RP 100 100 500 500 CATCH ALL v6 ICMP NA Q3/Q11 CP/RP 60 ...

  • Dell 9.8(0.0) - page 605

    400 2000 2000 VLT CTRL Q12 RP 2000 2000 3000 3000 VLT IPM PDU Q4/Q12 CP/RP 500 500 3000 3000 VLT TTL1 Q0 CP 100 100 500 500 HYPERPULL Q22 LP 500 500 1000 1000 OPENFLOW Q14 RP 300 300 1000 1000 FEFD Q7 CP 150 150 1000 1000 TRACEFLOW Q20 LP 200 200 500 500 FCoE Q14 RP 300 300 2000 2000 SFLOW Q23 LP 5000 5000 3000 3000 L3 LOCAL TERMINATED Q4 CP 400 40 ...

  • Dell 9.8(0.0) - page 606

    11 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell Networking operating software commands for data center bridging feature ...

  • Dell 9.8(0.0) - page 607

    Version Description 9.7(0.0) Introduced on the Z9500. Usage Information By default, iSCSI is enabled on the unit and the flow control is enabled on all of the interfaces. It is also acts as defaults when the link-level flow control is enabled on one or more interfaces. To enable DCB, do one of the following: • Apply the dcb-map command with the n ...

  • Dell 9.8(0.0) - page 608

    Usage Information If you do not use the statistics parameter, both hardware and DCBx counters clear. clear pfc counters sfm backplane all Clear the PFC counters on sfm and backplane ports. Syntax clear pfc counters sfm <0-5/all> backplane all Parameters backplane all Enter the keywords all backplane all to clear the counters on all interfaces ...

  • Dell 9.8(0.0) - page 609

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the Z9500. Usage Information • When you configure lossless queues on an interface, PFC priority configuration is not allowed on the dcb-input profile applied on the interface. • The maximum number of lossless queues glo ...

  • Dell 9.8(0.0) - page 610

    Usage Information Specify a linecard number on the Master switch in a stack. NOTE: show dcb command without options displays DCB buffer details for all linecards, SFMs, and for all port-pipes. Example Dell#sh dcb linecard 2 port-set 0 DCB Status: Enabled, PFC Queue Count: 2 linecard Total Buffer PFC Total Buffer PFC Shared Buffer PFC Available Buff ...

  • Dell 9.8(0.0) - page 611

    Field Description Admin mode is on Admin is enabled PFC admin mode is on or off with a list of the configured PFC priorities. When the PFC admin mode is on, PFC advertisements are enabled to be sent and received from peers; received PFC configuration take effect. The admin operational status for a DCBX exchange of PFC configuration is enabled or di ...

  • Dell 9.8(0.0) - page 612

    Field Description Application Priority TLV: Remote FCOE Priority Map Status of FCoE advertisements in application priority TLVs from the remote peer port: enabled or disabled. Application Priority TLV: Remote ISCSI Priority Map Status of iSCSI advertisements in application priority TLVs from the remote peer port: enabled or disabled. PFC TLV Statis ...

  • Dell 9.8(0.0) - page 613

    Application Priority TLV Parameters : -------------------------------------- FCOE TLV Tx Status is disabled ISCSI TLV Tx Status is disabled Local FCOE PriorityMap is 0x8 Local ISCSI PriorityMap is 0x10 Remote FCOE PriorityMap is 0x8 Remote ISCSI PriorityMap is 0x8 0 Input TLV pkts, 1 Output TLV pkts, 0 Error pkts, 0 Pause Tx pkts, 0 Pause Rx pkts s ...

  • Dell 9.8(0.0) - page 614

    ETS Commands dcb-enable Enable data center bridging. Syntax dcb enable[ pfc-queues 1|4 ] To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. Defaults The default is 2 Command Modes CONFIGURATION Command History This guide is platform ...

  • Dell 9.8(0.0) - page 615

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the Z9500. show interface ets Displays the ETS configur ...

  • Dell 9.8(0.0) - page 616

    ------------------- 0 0,1,2,4,5,6,7 50 400 100 4000 400 ETS 1 3 50 - - - - ETS 2 - - - - - - 3 - - - - - - 4 - - - - - - 5 - - - - - - 6 - - - - - - 7 - - - - - - Remote Parameters : ------------------- Remote is disabled Local Parameters : ------------------ Local is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rat ...

  • Dell 9.8(0.0) - page 617

    DCBX Commands advertise dcbx-tlv On a DCBX port with a manual role, configure the PFC and ETS TLVs advertised to DCBX peers. Syntax advertise dcbx-tlv {ets-conf | ets-reco | pfc} [ets-conf | ets- reco | pfc] [ets-conf | ets-reco | pfc] To remove the advertised ETS TLVs, use the no advertise dcbx-tlv command. Parameters {ets-conf | ets- reco | pfc} ...

  • Dell 9.8(0.0) - page 618

    dcbx port-role Configure the DCBX port role the interface uses to exchange DCB information. Syntax dcbx port-role {config-source | auto-downstream | auto-upstream | manual} To remove DCBX port role, use the no dcbx port-role {config-source | auto-downstream | auto-upstream | manual} command. Parameters config-source | auto- downstream | auto-upstre ...

  • Dell 9.8(0.0) - page 619

    dcbx version Configure the DCBX version used on the interface. Syntax dcbx version {auto | cee | cin | ieee-v2.5} To remove the DCBX version, use the dcbx version {auto | cee | cin | ieee-v2.5} command. Parameters auto | cee | cin | ieee-v2.5 Enter the DCBX version type used on the interface, where: • auto : configures the port to operate using t ...

  • Dell 9.8(0.0) - page 620

    Parameters {all | auto- detect-timer | config-exchng | fail | mgmt | resource | sem | tlv} Enter the type of debugging, where: • all : enables all DCBX debugging operations. • auto-detect-timer : enables traces for DCBX auto- detect timers. • config-exchng : enables traces for DCBX configuration exchanges. • fail : enables traces for DCBX f ...

  • Dell 9.8(0.0) - page 621

    Version Description 9.7(0.0) Introduced on the Z9500. Usage Information This command is available at the global level only. iscsi priority-bits Configure the iSCSI priority advertised for the iSCSI protocol in application priority TLVs. Syntax iscsi priority-bits priority-bitmap To remove the configured iSCSI priority, use the no iscsi priority-bit ...

  • Dell 9.8(0.0) - page 622

    Version Description 9.7(0.0) Introduced on the Z9500. Usage Information To clear DCBX frame counters, use the clear dcbx counters interface stack-unit/port command. The following describes the show interface dcbx detail command shown in the following example. Field Description Interface Interface type with chassis slot and port number. Port-Role Co ...

  • Dell 9.8(0.0) - page 623

    Field Description Acknowledgment Number Local DCBX Status: Protocol State Current operational state of the DCBX protocol: ACK or IN- SYNC. Peer DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs received from the peer device. Peer DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs recei ...

  • Dell 9.8(0.0) - page 624

    Local DCBX Compatibility mode is CEE Local DCBX Configured mode is CEE Peer Operating version is CEE Local DCBX TLVs Transmitted: ErPfi Local DCBX Status ----------------- DCBX Operational Version is 0 DCBX Max Version Supported is 0 Sequence Number: 2 Acknowledgment Number: 2 Protocol State: In-Sync Peer DCBX Status: ---------------- DCBX Operatio ...

  • Dell 9.8(0.0) - page 625

    Use the dcb-map command to create a DCB map to specify PFC and ETS settings and apply it on Ethernet ports. After you apply a DCB map to an interface, the PFC and ETS settings in the map are applied when the Ethernet port is enabled. DCBx is enabled on Ethernet ports by default. The dcb-map command is supported only on physical Ethernet interfaces. ...

  • Dell 9.8(0.0) - page 626

    priority-pgid Assign 802.1p priority traffic to a priority group in a DCB map. Syntax priority-pgid dot1p0_group-num dot1p1_group-num dot1p2_group- num dot1p3_group-num dot1p4_group-num dot1p5_group-num dot1p6_group-num dot1p7_group-num Parameters dot1p0_group- num Enter the priority group number for each 802.1p class of traffic in a DCB map. dot1p ...

  • Dell 9.8(0.0) - page 627

    • Priority group 1 contains traffic with dot1p priority 3. • Priority group 2 contains traffic with dot1p priority 4. • Priority group 4 contains traffic with dot1p priority 5, 6, and 7. To remove a priority-pgid configuration from a DCB map, enter the no priority-pgid command. priority-group bandwidth pfc Configure the ETS bandwidth allocati ...

  • Dell 9.8(0.0) - page 628

    Usage Information Use the dcb-map command to configure priority groups with PFC and/or ETS settings and apply them to Ethernet interfaces. Use the priority-pgid command to map 802.1p priorities to a priority group. You can assign each 802.1p priority to only one priority group. A priority group consists of 802.1p priority values that are grouped to ...

  • Dell 9.8(0.0) - page 629

    Command Modes CONFIGURATION Command History Version Description 9.7(0.0) Introduced on the Z9500. Usage Information The dcb-map linecard all backplane all command overwrites any previous DCB maps applied to backplane dcb-policy buffer-threshold sfm all port-set all backplane all Assign the DCB policy to all sfm and backplane ports interfaces. This ...

  • Dell 9.8(0.0) - page 630

    dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. You must configure the shared buffer size to be less than the total PFC buffer size. If the buffer size and DCB buffer threshold settings are applied on one or more ports, a validation is performed to determine whether following condition is ...

  • Dell 9.8(0.0) - page 631

    dcb pfc-shared-buffer-size sfm all Configure the maximum amount of shared buffer size for PFC packets on all sfm ports in kilobytes. Syntax dcb pfc-shared-buffer-size <value> sfm all Parameters KB Enter a number in the range from 0 to 11210. Defaults The default is 3328KB for Z9500 platform. Command Modes CONFIGURATION Command History This gu ...

  • Dell 9.8(0.0) - page 632

    Usage Information When you enter the profile name, you enter the DCB buffer threshold configuration mode. You can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets. Example S4810-YU-MR-Dell(conf)#dcb buff ...

  • Dell 9.8(0.0) - page 633

    Command History Version Description 9.7(0.0) Introduced on the Z9500. Usage Information For each priority, you can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets. When PFC detects congestion on a queue ...

  • Dell 9.8(0.0) - page 634

    Example Example of show linecard 0 port-set 0 backplane all pfc buffer- threshold output Dell#show linecard 0 port-set 0 backplane all pfc buffer- threshold linecard 0 port-set 0 backplane all Queue# Lossless Buffer-size Pause-threshold Resume-offset Shared Threshold (KB) (KB) (KB) Weight ------------------------------------------------------------ ...

  • Dell 9.8(0.0) - page 635

    0 0 4 0 0 0 5 0 0 0 6 0 0 0 7 0 0 0 Example of show linecard 2 port-set 0 backplane all ets details output Dell#show linecard 2 port-set 0 backplane all ets details linecard 2 port-set 0 backplane all Max Supported PG is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters: -------------------- Admin is enabled PG-grp Priority# Bandwi ...

  • Dell 9.8(0.0) - page 636

    Version Description 9.7(0.0) Introduced on the Z9500. Usage Information NOTE: Please note that the existing "dcb pfc-shared-total-size / pfc-shared- buffer-size <value>" without any options is still applicable for z9500. When executed, it configures the value to both backplane and sfm units. Example Example of show sfm 0 backplane a ...

  • Dell 9.8(0.0) - page 637

    3 0 0 0 4 0 0 0 5 0 0 0 6 0 0 0 7 0 0 0 Example of show sfm 0 backplane all ets details output Dell#sh sfm 0 backplane all ets details sfm 0 backplane all Max Supported PG is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters: -------------------- Admin is enabled PG-grp Priority# Bandwidth TSA -------------------------------------- ...

  • Dell 9.8(0.0) - page 638

    queue 0 to queue 7 Specify the queue number to which the QoS policy buffer parameters apply pause Pause frames to be sent at the specified buffer limit levels and pause packet settings no-drop The packets for this queue must not be dropped value Enter a number in the range of 0 to 7 to denote the priority to be allocated to the dynamic buffer contr ...

  • Dell 9.8(0.0) - page 639

    You can use set up both the administrative and peer-related PFC priorities. For example, you can configure the intended buffer configuration for all 8 priorities. If you configure the number of lossless queues as 4 and if the administrator- configured priorities configured within the DCB input policy is applied, then the configuration for those pri ...

  • Dell 9.8(0.0) - page 640

    Example dcb-policy buffer-threshold linecard all portset all backplane all test dcb-policy buffer-threshold linecard all backplane all Assign the DCB buffer configuration on the backplane ports. This setting takes precedence over the global buffer-threshold setting. Syntax [no] dcb-policy buffer-threshold linecard <0-2>|all [port-set <0-3/ ...

  • Dell 9.8(0.0) - page 641

    Parameters name Enter the name of the profile, which can be a string of up to 32 characters in length. Command Modes EXEC EXEC Privilege Command History Version Description 9.7(0.0) Introduced on the Z9500. Usage Information The following table describes the output fields displayed for the show command: Field Description Name Name of the DCB buffer ...

  • Dell 9.8(0.0) - page 642

    Usage Information The following table describes the output fields displayed for the show running- config dcb-buffer-threshold command: Field Description Profile name Name of the DCB buffer threshold profile Priority The priority of the queue for which the buffer space settings apply buffer-size Ingress buffer size pause-threshold-value Buffer limit ...

  • Dell 9.8(0.0) - page 643

    - - - Denotes dynamic buffering is enabled in respective queues On interface in which PFC is not enabled: Dell#show interface tengigabitethernet 0/20 pfc buffer- threshold The following table describes the output fields displayed for the show interface pfc buffer-threshold command: Field Description queue Number of the queue lossless Whether the qu ...

  • Dell 9.8(0.0) - page 644

    configured PFC buffer size, the system determines whether this reduction in size is valid without disrupting the existing configuration. In such a scenario, you must disable and re-enable DCB. For example, if you modify the total buffer size to be 4000 KB from the previous size of 5000 KB, an error message is displayed that this reduction cannot be ...

  • Dell 9.8(0.0) - page 645

    Example Dell(conf)#dcb pfc-queues 4 dcb <ets | pfc> enable Enable priority flow control or enhanced transmission selection on interface. Syntax dcb <ets | pfc> enablepfc >enable • To disable ETS on interface, use “ no dcb ets enable ” command. • To disable PFC on interface, use “ no dcb pfc enable ” command. Defaults Enab ...

  • Dell 9.8(0.0) - page 646

    12 Debugging and Diagnostics The debugging and diagnostics commands are supported on the Dell Networking OS platform. This chapter contains the following sections: • Diagnostics and Monitoring Commands • Offline Diagnostic Commands • Buffer Tuning Commands • Hardware Commands Diagnostics and Monitoring Commands The following section describ ...

  • Dell 9.8(0.0) - page 647

    Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Restructured the command to accommodate core dumps for CP. Introduced on the C-Series and S-Series. Version 6.5.1.0 Application coredump naming convention enhanced to include application. Version 6.1.1.0 Introduced Usage Information The kernel core dump can be large and may take up to five to ...

  • Dell 9.8(0.0) - page 648

    Defaults Crash kernel files are uploaded to flash by default. Command Modes CONFIGURATION Command History Version 9.7(0.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Added information about ftp password and URL to Usage Information . Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the ...

  • Dell 9.8(0.0) - page 649

    the line-card processor (LP) and 0 for the Control processor (CP) and Route Processor (RP). To display the system results in this text file, use the show file command. Important Points to Remember • Offline diagnostics can only be run when the unit is offline. • You can only run offline diagnostics on a unit to which you are connected via the c ...

  • Dell 9.8(0.0) - page 650

    level2 Enter the keyword level2 to run Level 2 diagnostics. Level 2 diagnostics are a full set of diagnostic tests with no support for automatic partitioning. Level 2 diagnostics are used primarily for on-board loopback tests and more extensive component diagnostics. Various components on the board are put into Loopback mode and test packets are tr ...

  • Dell 9.8(0.0) - page 651

    Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced the verbose option. Version 7.7.1.0 Introduced on the S-Series. Related Commands offline stack-unit — bring a switch offline to run diagnostic tests. online stack-unit — reload the system after running offline diagnostic tests. offline system Place the switch in the offline sta ...

  • Dell 9.8(0.0) - page 652

    Related Commands diag — run diagnostic tests on an offline switch. online stack-unit — reload the system after running offline diagnostic tests. online system Reload a switch after running offline diagnostic tests. Z9500 Syntax online system Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command ...

  • Dell 9.8(0.0) - page 653

    cp unit-id Enter the cp unit-id parameters to display the results only of the offline diagnostic tests run on the Control Processor CPU. The Control Processor CPU ID is 0. rp unit-id Enter the rp unit-id parameters to display the results only of the offline diagnostic test srun on the Route Processor CPU. The Route Processor CPU ID is 0. linecard u ...

  • Dell 9.8(0.0) - page 654

    Example: After offline diagnostics are run on a line card Dell# show diag linecard 0 summary Diag status of linecard member 0: --------------------------------------------------------------- ----------- linecard is currently offline. linecard level0 diag issued at Wed Jan 08, 2014 04:39:58 AM. Current diag status : Card diags are done. Duration of ...

  • Dell 9.8(0.0) - page 655

    ----------- DELL DIAGNOSTIC [0] PPID -- NA PPID Rev -- NA Service Tag -- NA Part Number -- NA Part Number Revision -- NA SW Version -- 9-2(1-509) Available free memory: 2,635,960,320 bytes LEVEL 0 DIAGNOSTIC eepromTest .................................................. PASS Starting test: i2cTest ...... ERROR: ioctl: "QSFP0" op(1)=READ WI ...

  • Dell 9.8(0.0) - page 656

    Starting test: portcardBoardRevisionTest ...... + Access Test for BCM unit 0 : PASSED + Access Test for BCM unit 1 : PASSED + Access Test for BCM unit 2 : PASSED portcardBoardRevisionTest ................................... PASS Starting test: qsfpOpticsTest ...... ERROR: Qsfp Module:12 is not present ERROR: Qsfp Module:13 is not present ERROR: Qsf ...

  • Dell 9.8(0.0) - page 657

    The following is a list of the Dell Networking OS version history for this command. Version 9.2(1.0) Introduced on the Z9500. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced the verbose option. Version 7.7.1.0 Introduced on the S-Series. show di ...

  • Dell 9.8(0.0) - page 658

    Offline). Linecard slot 1: No card diags executed yet (Card Offline). Linecard slot 2: No card diags executed yet (Card Offline). Linecard slot 3: No card diags executed yet (Card Offline). ---------------------------- Example: After offline diagnostics are run on a switch Dell# show diag information Diag information: Diag software image version: 9 ...

  • Dell 9.8(0.0) - page 659

    level1 Enter the keyword Level1 to display only the Level 1 diagnostic tests. Level 1 diagnostics is a smaller set of diagnostic tests with support for automatic partitioning. They perform status/self test for all the components on the board and test their registers for appropriate values. In addition, they perform extensive tests on memory devices ...

  • Dell 9.8(0.0) - page 660

    NO NO NO portcardBoardRevisionTest: ALL RUN YES NO NO NO NO portcardHiGigLinkStatusTest: ALL RUN NO YES NO NO NO portcardIxiaTrafficCmd: ALL RUN NO NO NO NO YES portcardPortStats: ALL RUN NO NO NO NO YES portcardXELinkStatusTest: ALL RUN NO YES NO NO NO qsfpOpticsTest: ALL RUN YES YES NO NO NO qsfpPhyTest: ALL RUN YES YES NO NO NO qsfpPresenceTest: ...

  • Dell 9.8(0.0) - page 661

    buffer-profile (Configuration) Create a buffer profile that can be applied to an interface. Z9500 Syntax buffer-profile {fp | csf] profile-name {global {1Q | | 4q} Parameters fp Enter the keyword fp to create a buffer profile for the Field Processor. csf Enter the keyword csf to create a buffer profile for the Switch Fabric Processor. profile-name ...

  • Dell 9.8(0.0) - page 662

    If the default buffer-profile is active, Dell Networking OS displays an error message instructing you to remove the default configuration using the no buffer- profile global command. Reload the system for the global buffer-profile to take effect. Hardware Commands The hardware commands supported on the switch allow you to display information from a ...

  • Dell 9.8(0.0) - page 663

    Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the ES-Series. clear hardware Clear statistics from a specified hardware component. Z9500 Syntax clear hardware {cp {cpu {data-plane | i2c | sata-interface} statistics} | cp-switch {counters} | linecard slot-id {counters | cpu {data-plane | i2c | sata-interface} statistics} ...

  • Dell 9.8(0.0) - page 664

    • cpu sata-interface statistics : Clears sata- interface error counter statistics. unit unit-num Enter the unit unit-num parameters with a command option to clear hardware statistics for a specified NPU. The range of NPU numbers is 0 to 3. The command options are: • counters : Clears the packets counters. party-bus Enter the keyword party-bus w ...

  • Dell 9.8(0.0) - page 665

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Related Commands show hardware — displays the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from a specified line card. Z9500 Synt ...

  • Dell 9.8(0.0) - page 666

    clear hardware vlan-counters Clear VLAN statistics. Syntax clear hardware vlan-couters vlan-id Parameters vlan-id Enter the interface VLAN number. The range is from 1 to 4094. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networki ...

  • Dell 9.8(0.0) - page 667

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9. ...

  • Dell 9.8(0.0) - page 668

    Command Modes EXEC Privilege Example Dell# show control-traffic counters Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.2(1.0) Introduc ...

  • Dell 9.8(0.0) - page 669

    sfm sfm-unit-num {buffer {total-buffer | unit unit-num {port | total-buffer}} | counters | details| drops | port-stats | register | table-dump}} Parameters cp Enter the keywords cp with a command option to display hardware statistics from the Control Processor. The command options are: • cpu data-plane statistics : Displays data-plane statistics, ...

  • Dell 9.8(0.0) - page 670

    output counters to which the stacking module is connected. • cpu i2c statistics : Displays active i2c-address statistics. • cpu management statistics : Displays management port counters for a specified line card. • cpu sata-interface statistics : Displays sata- interface error counter statistics. • drops unit unit-num : Displays the number ...

  • Dell 9.8(0.0) - page 671

    • cpu management statistics : Displays management port counters. • cpu sata-interface statistics : Displays sata- interface error counter statistics. sfm sfm-unit- num Enter the keyword sfm with an Switch Fabric Module (SFM) unit number and a command option to display hardware statistics from the specified SFM on the Z9500. The range of SFM uni ...

  • Dell 9.8(0.0) - page 672

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Modified the stack-port keyword range expanded from 49-52 to 0-52; output modified for the cpu data-plane statistics option; the following options were added: drops [unit 0-1 [port 0-27]] and unit 0-1 {counters | details | port-stats [detail] | register} 7.7.1.0 Introduced on the S-Series ...

  • Dell 9.8(0.0) - page 673

    Example (Party-Bus Port: Statistics) Dell#show hardware party-bus port 0 statistics Party Bus Transmit Counters for port 0: Tx Octets = 231162055 Tx Drop Packets = 0 tx_q0_pkts = 303459 tx_q1_pkts = 0 tx_q2_pkts = 0 tx_q3_pkts = 0 tx_q4_pkts = 0 tx_q5_pkts = 0 tx_broad_pkts = 6178 tx_multi_pkts = 852 tx_uni_pkts = 296429 tx_pause_pkts = 0 tx_cols = ...

  • Dell 9.8(0.0) - page 674

    0 1 0 0 0 0 0 4 5 0 0 0 0 0 8 9 0 0 0 0 0 12 13 3258 0 0 0 0 16 17 0 0 0 0 0 17 18 0 0 0 0 0 18 19 0 0 0 0 0 19 20 0 0 0 0 0 20 21 0 0 0 0 0 21 22 0 0 0 0 0 22 23 0 0 0 0 0 23 24 0 0 0 0 0 24 25 0 0 0 0 0 28 29 0 0 0 0 0 32 33 0 0 0 0 0 36 37 0 0 0 0 0 40 41 0 0 0 0 0 44 45 0 0 0 0 0 Internal 50 0 0 0 0 0 Internal 51 0 0 0 0 0 Internal 52 0 0 0 0 0 ...

  • Dell 9.8(0.0) - page 675

    Example (Linecard Unit: Port-Stats) Dell#show hardware linecard 2 unit 0 port-stats ena/ speed/ link auto STP lrn inter max loop port link duplex scan neg? state pause discrd ops face frame back xe0 !ena 40G FD SW No Forward Tag F CR4 1550 xe1 !ena 40G FD SW No Forward Tag F XGMII 1550 xe2 !ena 40G FD SW No Forward Tag F XGMII 1550 xe3 up 40G FD SW ...

  • Dell 9.8(0.0) - page 676

    hg10 up 42G FD SW No Forward None F XGMII 16360 hg11 up 42G FD SW No Forward None F XGMII 16360 Example (Linecard Unit: Register) Dell#show hardware linecard 2 unit 0 register 0x77120000 ARB_RAM_DBGCTRL.ipipe0 = 0x00000000 0x04000134 ASF_PORT_CFG.cpu0 = 0x00000000 0x04000107 ASF_PORT_CFG.xe0 = 0x0000001c 0x04000109 ASF_PORT_CFG.xe1 = 0x0000001c 0x0 ...

  • Dell 9.8(0.0) - page 677

    0x56002008 BUF_CFG(8).mmu0 = 0x00000000 0x56002009 BUF_CFG(9).mmu0 = 0x00000000 0x5600200a BUF_CFG(10).mmu0 = 0x00000000 0x5600200b BUF_CFG(11).mmu0 = 0x00000000 0x5600200c BUF_CFG(12).mmu0 = 0x00000000 0x5600200d BUF_CFG(13).mmu0 = 0x00000000 0x5600200e BUF_CFG(14).mmu0 = 0x00000000 0x5600200f BUF_CFG(15).mmu0 = 0x00000000 0x36000200 CBL_ATTRIBUTE ...

  • Dell 9.8(0.0) - page 678

    0x1e003007 CFAPBANKSTATUS(7).mmu0 = 0x00000026 0x1e003008 CFAPBANKSTATUS(8).mmu0 = 0x00000027 !------------------ output truncated ---------------! Example (Linecard Unit: Counters) Dell#show hardware linecard 0 unit 1 counters RUC.cpu0 : 528,687 +528,687 ING_NIV_RX_FRAMES.cpu0 : 528,687 +528,687 TDBGC6.cpu0 : 528,687 +528,687 PERQ_PKT(0).cpu0 : 1, ...

  • Dell 9.8(0.0) - page 679

    Front End Link Status 0x00080800 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 Front End Port Presence 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 Backplane Link Status 0xc0000300 0x000c0000 ****************************************************** Link Status of all the ports in the Device - 0 The linkStatus of Front En ...

  • Dell 9.8(0.0) - page 680

    The tm-tp for Index 9 is : -1 | -1 The tm-tp for Index 10 is : -1 | -1 The tm-tp for Index 11 is : -1 | -1 ************************************************* ModPort Table for Device - 0 For Destination Mod Id 0 Destination Port is 50 For Destination Mod Id 1 Destination Port is 50 For Destination Mod Id 2 Destination Port is 50 For Destination Mod ...

  • Dell 9.8(0.0) - page 681

    Default Packet Buffer allocate for the Interface: 141 Used Packet Buffer for the Interface: 0 ----- Buffer Stats for Interface Fo 1/2 ----- Maximum Shared Limit for the Interface: 39856 Default Packet Buffer allocate for the Interface: 141 Used Packet Buffer for the Interface: 0 ----- Buffer Stats for Interface Fo 1/3 ----- Maximum Shared Limit for ...

  • Dell 9.8(0.0) - page 682

    Example (Linecard: Backplane-link Status) Dell#show hardware linecard 0 bp-link-state Total valid Links - 39 Valid Link bmp - 0xfc0003f0-000fc000-3f0000fc-0003f000-00380000 Valid Link bmp State - 0xf40003f0-000fc000-3d0000fc-0003f000-00380000 Example (Linecard Unit Port: HiGig Port Statistics) Dell#show hardware linecard 0 hg-stats unit 1 port 50 H ...

  • Dell 9.8(0.0) - page 683

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list o ...

  • Dell 9.8(0.0) - page 684

    RX - PFC Frame Priority 4 0 RX - PFC Frame Priority 5 0 RX - PFC Frame Priority 6 0 RX - PFC Frame Priority 7 0 RX - Debug Counter 0 0 RX - Debug Counter 1 0 RX - Debug Counter 2 0 <output truncated for brevity> show hardware buffer interface Display buffer statistics for a specific interface. Syntax show hardware buffer inteface interface {p ...

  • Dell 9.8(0.0) - page 685

    Example displaying priority-group range Dell#show hardware buffer interface tengigabitethernet 1/1 priority-group 0 buffer-info ----- Buffer stats for unit: 0 port: 1 (interface Te 1/1) ----- --------------------------------------------------------------- --------- PG# PRIORITIES ALLOTED (CELLS) COUNTER (CELLS) MIN SHARED MODE HDRM MIN SHARED HDRM ...

  • Dell 9.8(0.0) - page 686

    Used Packet Buffer: 0 ----- Buffer Stats for Interface Te 1/1 Queue 11 ----- Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: 8 <output truncated for brevity> show hardware buffer-stats-snapshot Displays buffer statistics tracking resource information for a specific interface. Syntax show hardware buffer-stats-snapsho ...

  • Dell 9.8(0.0) - page 687

    Example displaying egress queue- level snapshot for both unicast and multicast packets for the specific interface Dell# show hardware buffer-stats-snapshot resource interface fortyGigE 0/0 queue all Unit 0 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------- Q# TYPE Q# TOTAL BUFFERED CELLS ------------------------------------- ...

  • Dell 9.8(0.0) - page 688

    Example displaying egress queue- level snapshot for multicast packets for the specific interface Dell#show hardware buffer-stats-snapshot resource interface fortyGigE 0/0 queue mcast 3 Unit 1 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------- Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------- MCAST 3 0 D ...

  • Dell 9.8(0.0) - page 689

    show hardware ipv6 Display information about IPv6 ACLs used on a Z9500 line card and port pipe. Z9500 Syntax show hardware ipv6 {eg-acl | in-acl} linecard slot-id port-set port-pipe Parameters eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to display ingress or egress ACL data. linecard slot-id Enter the linecard slot-id para ...

  • Dell 9.8(0.0) - page 690

    DATA=0x00000004 MASK=0x0000000c L3Routable Offset: 166 Width: 1 DATA=0x00000001 MASK=0x00000001 OutPort Offset: 195 Width: 7 DATA=0x00000001 MASK=0x0000007f action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)} policer= statistics=NULL EID 0x0000130d: gid=0xd, slice=0, slice_idx=0x1, part =0 prio=0x130d, flags=0x10202, Installed, En ...

  • Dell 9.8(0.0) - page 691

    linecard slot-id Enter the linecard slot-id parameters to specify a Z9500 line card. The range of slot IDs is from 0 to 2. port-set number Enter the keywords port-set number parameters to specify a port pipe (set of ports) on a line card. The range of port-set numbers is from 0 to 3. Defaults none Command Modes EXEC Privilege Command History This g ...

  • Dell 9.8(0.0) - page 692

    policer= statistics={stat id 63 slice = 3 idx=0 entries=1} {Packets} EID 0x000010cc: gid=0x10, slice=3, slice_idx=0x2, part =0 prio=0x10cc, flags=0x10202, Installed, Enabled tcam: color_indep=0, DstMac Offset: 90 Width: 48 DATA=0x00000180 c2000000 MASK=0x0000ffff ff000000 StageEgress action={act=DropCancel, param0=0(0), param1=0(0), param2=0(0), pa ...

  • Dell 9.8(0.0) - page 693

    Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Example Dell#show hardware layer3 eg-acl linecard 0 port-set 0 EID 0x000011b9: gid=0xf, slice=2, slice_idx=0, part =0 prio=0x11b9, flags=0x10202, Installed, Enabled tcam: color_indep=0, StageEgress Color Offset: 5 Width: 2 DATA ...

  • Dell 9.8(0.0) - page 694

    MASK=0x00000001 OutPort Offset: 185 Width: 7 DATA=0x00000005 MASK=0x0000007f action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)} policer= statistics={stat id 111 slice = 2 idx=4 entries=1} {Packets} show hardware system-flow Display Layer 3 ACL or QoS data for traffic flows on the central switch (aggregated CoPP) or a specified li ...

  • Dell 9.8(0.0) - page 695

    Example Dell#show hardware system-flow layer2 cp-switch ############## FP Entry for STP ################ EID 0x00000000: gid=0x1, slice=0, slice_idx=0, part =0 prio=0x100, flags=0x10602, Installed, Enabled tcam: color_indep=1024, InPort DATA=0x000000000000000000000000000000000000000000000000000003c0 00003f80 MASK=0x000000000000000000000000000000000 ...

  • Dell 9.8(0.0) - page 696

    _bcmFieldQualifyData Offset: 61 Width: 128 DATA=0x00000080 00000000 00000000 00000000 MASK=0x00003fc0 00000000 00000000 00000000 slice=0, slice_idx=0x101, part =1 prio=0xff, flags=0x10302, Installed, Enabled tcam: color_indep=0, action={act=CosQNew, param0=6(0x6), param1=0(0), param2=0(0), param3=0(0)} action={act=RedirectPbmp, param0=1073741824(0x ...

  • Dell 9.8(0.0) - page 697

    MASK=0x000000000000000000000000000000000000000000000000000003ff c0003ffc InPorts DATA=0x000000000000000000000000000000000000000000000000000003c0 00003f80 MASK=0x000000000000000000000000000000000000000000000000000003ff c0003ffc Stage --More-- show hardware vlan-counters Display the hardware VLAN statistics. Syntax show hardware vlan-counters vlan-id ...

  • Dell 9.8(0.0) - page 698

    show hardware drops Displays internal drops on the specified interface or for a range of interface. Syntax show hardware drops interface interface Parameters interface Enter any of the following keywords and slot/port or slot/ port-range or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the sl ...

  • Dell 9.8(0.0) - page 699

    Example displaying internal drops for the specific interface Dell#show hardware drops interface tengigabitethernet 2/1 Drops in Interface Te 2/1: --- Ingress Drops --- Ingress Drops : 0 IBP CBP Full Drops : 0 PortSTPnotFwd Drops : 0 IPv4 L3 Discards : 0 Policy Discards : 0 Packets dropped by FP : 0 (L2+L3) Drops : 0 Port bitmap zero Drops : 0 Rx VL ...

  • Dell 9.8(0.0) - page 700

    tcpdump Enable a TCP dump for CPU-bound traffic on the Control and Router Processors.. Z9500 Syntax tcpdump {cp | rp} [capture-duration time | filter expression | max-file-count value | packet-count value | snap-length value | write-to path ] To disable the TCP dump, use the no tcpdump command. Parameters cp Enter the keyword cp to perform a dump o ...

  • Dell 9.8(0.0) - page 701

    Defaults TCP dumps are disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introdu ...

  • Dell 9.8(0.0) - page 702

    13 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. The Dell Networking OS supports the basic DHCP co ...

  • Dell 9.8(0.0) - page 703

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE . conflicts Enter the keyword conflicts to delete all of the log entries created for IP address conflicts. server statistics Enter the keywords server statistics to clear all counter information on the DHCP server. Defaults none Command Modes EXEC Privilege Command History This gu ...

  • Dell 9.8(0.0) - page 704

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. Related Commands show ip dhcp snooping — displays the contents of the DHCP binding table. debug ipv6 dhcp To enable debug logs for DHCPv6 rel ...

  • Dell 9.8(0.0) - page 705

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE . Defaults none Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Example Dell# d ...

  • Dell 9.8(0.0) - page 706

    debug ip dhcp client packets Activate the debugging and display of log messages for DHCP packets sent and received on DHCP client interfaces. Z9500 Syntax debug ip dhcp client packets [interface type slot / port ] Parameters interface typeslot/port Enter the keyword interface with the interface type and slot/port information to display DHCP log mes ...

  • Dell 9.8(0.0) - page 707

    Last logging buffer cleared: Jan 7 01:41:17 Jan 7 01:42:34: %SYSTEM:CP %DHCLIENT-5-DHCLIENT-LOG: DHCLIENT_DBG_PKT: DHCP RELEASE sent in Interface Fo 2/0 Jan 7 01:41:39: %SYSTEM:CP %DHCLIENT-5-DHCLIENT-LOG: DHCLIENT_DBG_PKT: Received DHCPACK packet in InterfaceFo 2/0 with Lease-IP:100.1.1.253, Mask:255.255.255.0, Server-Id: 100.1.1.2 Jan 7 01:41:39: ...

  • Dell 9.8(0.0) - page 708

    disable Disable the DHCP server. Z9500 Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command ...

  • Dell 9.8(0.0) - page 709

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. domain-name Assign a domain to clients based on the address p ...

  • Dell 9.8(0.0) - page 710

    Parameters address Enter a single address to be excluded from the pool. low-address Enter the lowest address in a range of addresses to be excluded from the pool. high-address Enter the highest address in a range of addresses to be excluded from the pool. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command ...

  • Dell 9.8(0.0) - page 711

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. host For manual (rather than automatic) configurations, assign a host to a single-address pool. Z9500 Syntax host address Parameters address/mask Enter the host IP address and sub ...

  • Dell 9.8(0.0) - page 712

    Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 713

    Parameters remote-id hostname Set the hostname as the remote ID in Option 82. remote-id remote-id Enter the name to be used as the remote ID in Option 82; maximum: 64 characters. remote-id mac Use the chassis MAC address as the remote ID in Option 82. Default Option 82 uses the chassis MAC address as the remote ID. Command Modes CONFIGURATION Comma ...

  • Dell 9.8(0.0) - page 714

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. Usage Information Use this command to includ ...

  • Dell 9.8(0.0) - page 715

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 716

    netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell Networking recommends specifying clients as hybrid . Z9500 Syntax netbios-node-type type Parameters type Enter the NETBIOS node type: • Broadcast: Enter the keyword b-node . • Hybrid: Enter the keyword h-node . • Mixed: Enter the keyword m-node . • Peer-to-pee ...

  • Dell 9.8(0.0) - page 717

    Defaults none Command Modes DHCP <POOL> Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500 ...

  • Dell 9.8(0.0) - page 718

    show ip dhcp client statistics Display statistical information about DHCP client interfaces. Z9500 Syntax show ip dhcp client statistics [interface type slot / port ] Parameters interface typeslot/port Enter the keyword interface with the interface type and slot/port information to display DHCP client information for a specified interface. The vali ...

  • Dell 9.8(0.0) - page 719

    show ip dhcp configuration Display the DHCP configuration. Z9500 Syntax show ip dhcp configuration [global | pool name ] Parameters pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command ...

  • Dell 9.8(0.0) - page 720

    show ip dhcp conflict Display the address conflict log. Z9500 Syntax show ip dhcp conflict address Parameters address Display a particular conflict log entry. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Lin ...

  • Dell 9.8(0.0) - page 721

    Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping Display the contents of the DHCP binding table or display the interfaces confi ...

  • Dell 9.8(0.0) - page 722

    Related Commands clear ip dhcp snooping — clears the contents of the DHCP binding table. show ip dhcp server statistics Display statistical information about a DHCP server. Z9500 Syntax show ip dhcp server statistics Defaults none Command Modes EXEC Privilege Command History Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduce ...

  • Dell 9.8(0.0) - page 723

    Configure Secure DHCP and DHCP Relay DHCP, as defined by RFC 2131, provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks, including using the switch as a DHCP relay agent. arp inspection Enable dynamic arp inspection (DAI) on a VLAN. ...

  • Dell 9.8(0.0) - page 724

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 725

    clear ipv6 dhcp snooping binding Clear all the DHCPv6 snooping binding database entries. Syntax clear ipv6 dhcp snooping binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command-Line Reference Guide . The follow ...

  • Dell 9.8(0.0) - page 726

    Version Description 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces. Usage Information When enabled, no learning takes place until you enable snooping on a VLAN. After disabling DHCP snooping, the binding table deletes and Option 82, IP Source Guard, and Dynamic ARP Inspection are disabled. DHCP snooping supports Layer 3 using ...

  • Dell 9.8(0.0) - page 727

    ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected: • For a 10-Gigabit Ethernet interface, enter the keyword tengigabitethernet . • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE . slot/port Ente ...

  • Dell 9.8(0.0) - page 728

    ipv6 ipv6-address interface interface-type | interface-number lease value command. Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IPv6 address. vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ipv6 ipv6- address Enter the keywor ...

  • Dell 9.8(0.0) - page 729

    Parameters minutes The range is from 5 to 21600. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version ...

  • Dell 9.8(0.0) - page 730

    ip dhcp snooping database renew Renew the binding table. Z9500 Syntax ip dhcp snooping database renew Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list ...

  • Dell 9.8(0.0) - page 731

    ip dhcp snooping trust Configure an interface as trusted. Z9500 Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Netw ...

  • Dell 9.8(0.0) - page 732

    ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Z9500 Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, ...

  • Dell 9.8(0.0) - page 733

    Version Description 9.7(0.0) Introduced on the S4810, S4820T, S6000 and Z-Series. ip dhcp snooping vlan Enable DHCP Snooping on one or more VLANs. Z9500 Syntax [no] ip dhcp snooping vlan name Parameters name Enter the name of a VLAN on which to enable DHCP Snooping. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platfor ...

  • Dell 9.8(0.0) - page 734

    Parameters vlan-id Enter the name of a VLAN id or list of the VLANs to enable DHCP Snooping. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command-Line Reference Guide . The following is a list of the Dell Network ...

  • Dell 9.8(0.0) - page 735

    Usage Information Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system. ipv6 helper-address Configures the ipv6 DHCP helper addresses without VRF. Syntax [no] ipv6 helper-addr ...

  • Dell 9.8(0.0) - page 736

    show ip dhcp binding Display the DHCP binding table. Z9500 Syntax show ip dhcp binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS ve ...

  • Dell 9.8(0.0) - page 737

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 738

    Invalid File : 0 Invalid Binding Entry : 0 Binding Entry lease expired : 0 Dell# 738 Dynamic Host Configuration Protocol (DHCP) ...

  • Dell 9.8(0.0) - page 739

    14 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a ...

  • Dell 9.8(0.0) - page 740

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 741

    Parameters ecmp crc16 | crc16cc | crc32MSB | crc32LSB | crc- upper | dest-ip | lsb | xor1 | xor2 | xor4 | xor8 | xor16 Enter the keyword ecmp then one of the following options: • crc16 : Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc : Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial • crc32MSB : Use CRC3 ...

  • Dell 9.8(0.0) - page 742

    lag { crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16 } Enter the keyword lag then one of the following options: • crc16 : Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc : Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial • crc32MSB : Use CRC32_UPPER — MSB 16 bits of computed CR ...

  • Dell 9.8(0.0) - page 743

    Version Description 7.7.1.1 Added the nh-ecmp option. 6.5.1.0 Added the line card option on TeraScale only. 6.3.1.0 Added support for ECMP and LAG on TeraScale only. Usage Information To ensure that CRC is not used for LAG, set the default hash-algorithm method. For example, hash-algorithm ecmp xor lag checksum nh-ecmp checksum. The hash value calc ...

  • Dell 9.8(0.0) - page 744

    hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Z9500 Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters crc-upper Uses the upper 32 ...

  • Dell 9.8(0.0) - page 745

    Term heading Description heading The different hash algorithms are based on the number of ECMP group members and packet values. The default hash algorithm yields the most balanced results in various test scenarios, but if the default algorithm does not provide satisfactory distribution of traffic, use this command to designate another algorithm. Wh ...

  • Dell 9.8(0.0) - page 746

    Defaults crc16 algorithm Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on th ...

  • Dell 9.8(0.0) - page 747

    Version Description 8.3.11.4 Introduced on the Z9000. hash-algorithm seed Select the seed value for the ECMP, LAG, and NH hashing algorithm. Z9500 Syntax hash-algorithm seed value [linecard slot ] [port-set number ] Parameters seed value Enter the keyword seed then the seed value. The range is from 0 to 4095. linecard slot Enter the keyword linecar ...

  • Dell 9.8(0.0) - page 748

    NOTE: While the seed is stored separately on each port-pipe, the same seed is used across all CAMs. You cannot separate LAG and ECMP but you can use different algorithms across the chassis with the same seed. If LAG member ports span multiple port-pipes and line cards, set the seed to the same value on each port-pipe to achieve deterministic behavi ...

  • Dell 9.8(0.0) - page 749

    link-bundle-distribution trigger-threshold Provides a mechanism to set the threshold to trigger when traffic distribution begins being monitored on an ECMP link bundle. Z9500 Syntax link-bundle-distribution trigger-threshold [ percent ] To exit from ecmp group mode, use the exit command. Parameters percent Indicate the threshold value when traffic ...

  • Dell 9.8(0.0) - page 750

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 751

    show link-bundle distribution Display the link-bundle distribution for the interfaces in the bundle, type of bundle (LAG or ECMP), and the most recently calculated interface utilization (either bytes per second rate or maximum rate) for each interface. Z9500 Syntax show link-bundle-distribution Command Modes EXEC Privilege Command History This guid ...

  • Dell 9.8(0.0) - page 752

    15 Flex Hash This chapter describes the Flex Hash enhancements. load-balance ingress-port enable Enable the Flex hash feature. Z9500 Syntax load-balance ingress-port enable To disable the Flex hash capability, use the no version of this command. Default None Command Modes CONFIGURATION mode Command History Version 9.2.1.0 Introduced on the Z9500 sw ...

  • Dell 9.8(0.0) - page 753

    load-balance flexhash Configure Flex hash operation, such as whether IPv4 or IPv6 packets are processed by the Flex hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name. Z9500 Syntax load-ba ...

  • Dell 9.8(0.0) - page 754

    Version 9.3.0.0 Introduced on the S6000 platform. Usage Information With the introduction of various overlay technologies such as network virtualization using generic routing encapsulation (NVGRE) segments and Routable Remote Direct Memory Access (RRDMA) over Converged Ethernet (RRoCE), information related to a traffic flow is contained in the L4 h ...

  • Dell 9.8(0.0) - page 755

    Usage Information You can configure the optimal switchover functionality for LACP even if you do not enable the fast boot mode on the system. You must configure the long timeout mechanism for the LACP session to enable the fast boot capability to operate properly. This command applies to dynamic port-channel interfaces only. When applied on a stati ...

  • Dell 9.8(0.0) - page 756

    subinterface . If a Layer 3 interface is configured without the encapsulation 802.1Q VLAN ID or is an untagged interface in a VLAN , the dot1Q value is not preserved . 756 Flex Hash ...

  • Dell 9.8(0.0) - page 757

    16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the commands described in this chapter. fips mode enable Enable the FIPS cryptography mode on the platform. Z9500 Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes ...

  • Dell 9.8(0.0) - page 758

    show fips status Displays the status of the FIPS mode. Z9500 Syntax show fips status Defaults None Command Modes EXEC Example Dell#show fips status FIPS Mode: Enabled Dell# Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The follo ...

  • Dell 9.8(0.0) - page 759

    Version Description 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Example Dell #show ip ssh SSH server : enabled. SSH server version : v1 and v2. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryp ...

  • Dell 9.8(0.0) - page 760

    NOTE: The :: notation specifies successive hexadecimal fields of zeros. -c encryption cipher Enter the following encryption cipher to use. (For v2 clients only.) Without the FIPS mode enabled: • 3des-cbc : Force ssh to use 3des-cbc encryption cipher. With the FIPS mode enabled: • aes128–cbc : Force ssh to use the aes128–cbc encryption ciphe ...

  • Dell 9.8(0.0) - page 761

    Defaults As indicated above. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced ...

  • Dell 9.8(0.0) - page 762

    <cr> Dell#ssh 10.11.8.12 -c ? aes128-cbc Force ssh to use aes128-cbc encryption cipher aes256-cbc Force ssh to use aes256-cbc encryption cipher Dell #ssh 10.11.8.12 -m ? hmac-sha1 Force ssh to use hmac-sha1 HMAC algorithm hmac-sha1-96 Force ssh to use hmac-sha1-96 HMAC algorithm 762 FIPS Cryptography ...

  • Dell 9.8(0.0) - page 763

    17 FIP Snooping To enable the FCoE Transit feature and configure FIP snooping, use the following Dell Networking Operating System commands on the Z9500platform. In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (F ...

  • Dell 9.8(0.0) - page 764

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface. Z9500 Syntax clear fip-snooping statistics [interface vlan vlan-id | interface fortyGigE port-type port/slot | interfac ...

  • Dell 9.8(0.0) - page 765

    debug fip snooping Enable debugging on FIP snooping. Z9500 Syntax debug fip-snooping [all | acl | error | ifm | info | ipc | tx] Parameters all Enter the keyword all to enable debugging on all the options. acl Enter the keyword acl for ACL-specific debugging. error Enter the keyword error for error-specific debugging. ifm Enter the keyword ifm for ...

  • Dell 9.8(0.0) - page 766

    Parameters packet-type Enter the keyword packet-type and then the option type on which to enable debugging. The options are: • all — Enter the keyword all to enable debugging on all the options. • discovery — Enter the keyword discovery to enable debugging on FCF advertisements and ENode solicitation. • virtual-link-instantiation — Ente ...

  • Dell 9.8(0.0) - page 767

    feature fip-snooping Enable FCoE transit and FIP snooping on a switch. Z9500 Syntax feature fip-snooping To disable the FCoE transit feature, use the no feature fip-snooping command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Del ...

  • Dell 9.8(0.0) - page 768

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S482 ...

  • Dell 9.8(0.0) - page 769

    fip-snooping port-mode fcf Configure the port for bridge-to-FCF links. Z9500 Syntax fip-snooping port-mode fcf To disable the bridge-to-FCF link on a port, use the no fip-snooping port- mode fcf command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell ...

  • Dell 9.8(0.0) - page 770

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 9.2 ...

  • Dell 9.8(0.0) - page 771

    show fip-snooping enode Display information on the ENodes in FIP-snooped sessions, including the ENode interface and MAC address, FCF MAC address, VLAN ID and FC-ID. Z9500 Syntax show fip-snooping enode [ enode-mac-address ] Parameters enode-mac- address Enter the MAC address of the ENodes to display. Command Modes • EXEC • EXEC Privilege Comma ...

  • Dell 9.8(0.0) - page 772

    show fip-snooping fcf Display information on the FCFs in FIP-snooped sessions, including the FCF interface and MAC address, FCF interface, VLAN ID, FC-MAP value, FKA advertisement period, and number of ENodes connected. Z9500 Syntax show fip-snooping fcf [ fcf-mac-address ] Parameters fcf-mac- address Enter the MAC address of the FCF to display. Co ...

  • Dell 9.8(0.0) - page 773

    ------- ------------- ---- ------ -------------- ------------- 54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping sessions Display information on FIP-snooped sessions on all VLANs or a specified VLAN, including the ENode interface and MAC address, the FCF interface and MAC address, VLAN ID, FCoE MAC address and FCoE session ID number (FC ...

  • Dell 9.8(0.0) - page 774

    Field Description VLAN VLAN ID number the session uses. FCoE MAC MAC address of the FCoE session the FCF assigns. FC-ID Fibre Channel ID the FCF assigns. Port WWPN Worldwide port name of the CNA port. Port WWNN Worldwide node name of the CNA port. Example Dell# show fip-snooping sessions Enode MAC Enode Intf FCF MAC FCF Intf VLAN FCoE MAC FC-ID Por ...

  • Dell 9.8(0.0) - page 775

    port-type port/ slot Enter the port-type and slot number of the FIP packet statistics displays. port-channel- number Enter the port channel number of the FIP packet statistics displays. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell ...

  • Dell 9.8(0.0) - page 776

    Field Description Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snoop unicast discovery advertisements received on the interface. Number of FLOGI Accepts Number of FIP FLOGI accept frames received on the interfac ...

  • Dell 9.8(0.0) - page 777

    Number of FDISC Accepts :16 Number of FDISC Rejects :0 Number of FLOGO Accepts :0 Number of FLOGO Rejects :0 Number of CVL :0 Number of FCF Discovery Timeouts :0 Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 Dell(conf)# Dell# show fip-snooping statistics int tengigabitethernet 1/11 Number of Vlan Request ...

  • Dell 9.8(0.0) - page 778

    show fip-snooping system Display information on the status of FIP snooping on the switch (enabled or disabled), including the number of FCoE VLANs, FCFs, ENodes, and currently active sessions. Z9500 Syntax show fip-snooping system Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information abou ...

  • Dell 9.8(0.0) - page 779

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Example Dell# show fip-snooping vlan * = Default VLAN VLAN FC-MAP FCFs Enodes Sessions ---- ------ ---- ------ -------- *1 - - - - ...

  • Dell 9.8(0.0) - page 780

    18 Force10 Resilient Ring Protocol (FRRP) Force10 resilient ring protocol (FRRP) is supported on Dell Networking OS. FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high- speed token acro ...

  • Dell 9.8(0.0) - page 781

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19 ...

  • Dell 9.8(0.0) - page 782

    To disable debugging, use the no debug frrp {event | packet | detail} { ring-id } [countnumber] command. Parameters event Enter the keyword event to display debug information related to ring protocol transitions. packet Enter the keyword packet to display brief debug information related to control packets. detail Enter the keyword detail to display ...

  • Dell 9.8(0.0) - page 783

    description Enter an identifying description of the ring. Syntax description Word To remove the ring description, use the no description [ Word ] command. Parameters Word Enter a description of the ring. Maximum: 255 characters. Defaults none Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command inform ...

  • Dell 9.8(0.0) - page 784

    Defaults Disabled Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced ...

  • Dell 9.8(0.0) - page 785

    secondary interface Enter the keyword secondary to configure the secondary interface then one of the following interfaces and slot/port information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port inf ...

  • Dell 9.8(0.0) - page 786

    member-vlan Specify the member VLAN identification numbers. Syntax member-vlan { vlan-range } To return to the default, use the no member-vlan [ vlan-range ] command. Parameters vlan-range Enter the member VLANs using VLAN IDs (separated by commas), a range of VLAN IDs (separated by a hyphen), a single VLAN ID, or a combination. For example: VLAN I ...

  • Dell 9.8(0.0) - page 787

    Parameters master Enter the keyword master to set the Ring node to Master mode. transit Enter the keyword transit to set the Ring node to Transit mode. Defaults Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Co ...

  • Dell 9.8(0.0) - page 788

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19 ...

  • Dell 9.8(0.0) - page 789

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. De ...

  • Dell 9.8(0.0) - page 790

    Example (2 Summary) Dell#show frrp 2 summary Dell#show frrp 2 summary Ring-ID State Mode Ctrl_Vlan Member_Vlans ----------------------------------------------- 2 Up Master 2 11-20, 25, 27-30 Dell# Related Commands protocol frrp — enters the resilient ring protocol and designate a ring identification. timer Set the hello interval or dead interval ...

  • Dell 9.8(0.0) - page 791

    Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information The hello interval command is the interval at which ring frames are generated from ...

  • Dell 9.8(0.0) - page 792

    19 GARP VLAN Registration (GVRP) The Dell Networking OS supports basic GVRP commands on the switch. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withd ...

  • Dell 9.8(0.0) - page 793

    • VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all dynamic VLANs are removed. • GVRP manages the active topology, not non-topological data such as VLAN protocols. If a local bridge must classify and analy ...

  • Dell 9.8(0.0) - page 794

    Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Related Commands show gvrp statistics — displays the GVRP statistics. debug gvrp Enable debugging on GVRP. Z9500 Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Paramete ...

  • Dell 9.8(0.0) - page 795

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series disable Globally disable GVRP. Z9500 Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGUR ...

  • Dell 9.8(0.0) - page 796

    garp timers Set the intervals (in milliseconds) for sending GARP messages. Z9500 Syntax garp timers {join | leave | leave-all} To return to the previous setting, use the no garp timers {join | leave | leave-all} command. Parameters join Enter the keyword join then the number of milliseconds to configure the join time. The range is from 100 to 14748 ...

  • Dell 9.8(0.0) - page 797

    Usage Information • Join Timer — Join messages announce the willingness to register some attributes with other participants. For reliability, each GARP application entity sends a Join message twice and uses a join timer to set the sending interval. • Leave Timer — Leave announces the willingness to de-register with other participants. Toget ...

  • Dell 9.8(0.0) - page 798

    Related Commands disable — globally disables GVRP. gvrp registration Configure the GVRP register type. Z9500 Syntax gvrp registration {fixed | normal | forbidden} To return to the default, use the gvrp register normal command. Parameters fixed Enter the keyword fixed then the VLAN range in a comma- separated VLAN ID set. normal Enter the keyword ...

  • Dell 9.8(0.0) - page 799

    about the VLAN through GVRP. If the VLAN is removed from the port that sends GVRP advertisements to this device, the port stops being a member of the VLAN. To advertise or learn about VLANs through GVRP, use the forbidden command when you do not want the interface. Related Commands show gvrp — displays the GVRP configuration including the registr ...

  • Dell 9.8(0.0) - page 800

    show config Display the global GVRP configuration. Z9500 Syntax show config Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for thi ...

  • Dell 9.8(0.0) - page 801

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Example Dell#show garp timers GARP Timers Value (millis ...

  • Dell 9.8(0.0) - page 802

    • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on th ...

  • Dell 9.8(0.0) - page 803

    • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. summary Enter the keyword sum ...

  • Dell 9.8(0.0) - page 804

    Join Empty Transmitted: 156 Join In Transmitted: 0 Empty Transmitted: 0 Leave In Transmitted: 0 Leave Empty Transmitted: 0 Leave All Transmitted: 41 Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 Dell# Related Commands show gvrp — displays the GVRP configuration. 804 GARP VLAN Registration (GVRP) ...

  • Dell 9.8(0.0) - page 805

    20 Internet Group Management Protocol (IGMP) IGMP and IGMP snooping commands are supported by the Dell Networking OS on the switch. This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember • Dell Ne ...

  • Dell 9.8(0.0) - page 806

    group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format. interface interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGi ...

  • Dell 9.8(0.0) - page 807

    Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging of IGMP packets corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format. interface interface Enter the ...

  • Dell 9.8(0.0) - page 808

    ip igmp access-group To specify access control for packets, use this feature. Z9500 Syntax ip igmp access-group access-list To remove the feature, use the no ip igmp access-group access-list command. Parameters access-list Enter the name of the extended ACL (16 characters maximum). Defaults Not configured Command Modes INTERFACE (conf-if- interface ...

  • Dell 9.8(0.0) - page 809

    Defaults none Command Modes CONFIGURATION (conf-if- interface-slot/port ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5( ...

  • Dell 9.8(0.0) - page 810

    Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to ...

  • Dell 9.8(0.0) - page 811

    Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. E-Series legac ...

  • Dell 9.8(0.0) - page 812

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.0 Introduced on the C-Series in Interface VLAN mode only to enable t ...

  • Dell 9.8(0.0) - page 813

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.0 Introduced on the C-Series in I ...

  • Dell 9.8(0.0) - page 814

    Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introd ...

  • Dell 9.8(0.0) - page 815

    Version Description 9.7(0.0) Added support for VRF and Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. Usage Informa ...

  • Dell 9.8(0.0) - page 816

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 817

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Changed the default IGMP from version 2 to ve ...

  • Dell 9.8(0.0) - page 818

    • For a port channel interface, enter the keywords port- channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command i ...

  • Dell 9.8(0.0) - page 819

    Field Description Last Reporter Displays the IP address of the last host to be a member of the IGMP group. Example Dell#show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.0.2 Vlan 100 00:00:05 00:02:04 22 ...

  • Dell 9.8(0.0) - page 820

    show ip igmp interface View information on the interfaces participating in IGMP. Z9500 Syntax show ip igmp [vrf vrf-name ] interface [ interface ] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF. interface (OPTIONAL) Enter the interface type and slot/port info ...

  • Dell 9.8(0.0) - page 821

    Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. The show ip igmp interface command does not display information corresponding to the loop-back interfaces. Example Dell#show ip igmp interface TenGigabitEthernet 1/1 is down, line protocol is down Internet protocol processing disabled TenGiga ...

  • Dell 9.8(0.0) - page 822

    Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. Example Dell#show ip igmp ssm-map Interface Vlan 2 ...

  • Dell 9.8(0.0) - page 823

    • IGMP snooping does not react to Layer 2 topology changes triggered by spanning tree protocol (STP). • IGMP snooping reacts to Layer 2 topology changes multiple spanning tree protocol (MSTP) triggers by sending a general query on the interface that comes in the FWD state. Important Points to Remember for IGMP Querier • The IGMP snooping Quer ...

  • Dell 9.8(0.0) - page 824

    Version Description 9.7(0.0) Introduced on S-Series and Z–Series. Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Z9500 Syntax debug ip igmp snooping [ group address | interface ] • To disable de ...

  • Dell 9.8(0.0) - page 825

    Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. This command displays packets for IGMP and IGMP snooping. ip igmp snooping enable Enable IGMP snooping on all or a single VLAN. This command is the master on/off switch to enable IGMP snooping. Syntax ip igmp snooping enable To disable IGMP s ...

  • Dell 9.8(0.0) - page 826

    ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. Z9500 Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl- n ) Command History This guide is platform-specific. For command information abou ...

  • Dell 9.8(0.0) - page 827

    ip igmp snooping flood This command controls the flooding behavior of unregistered multicast data packets. Z9500 Syntax ip igmp snooping flood Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference G ...

  • Dell 9.8(0.0) - page 828

    Parameters milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds . Defaults 1000 milliseconds Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . ...

  • Dell 9.8(0.0) - page 829

    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 512. Defaults Not configured. Comm ...

  • Dell 9.8(0.0) - page 830

    Command Modes INTERFACE VLAN — (conf-if-vl- n ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z ...

  • Dell 9.8(0.0) - page 831

    • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command ...

  • Dell 9.8(0.0) - page 832

    Member Ports: Te 1/17 Dell# show ip igmp snooping mrouter Display multicast router interfaces. Z9500 Syntax show ip igmp snooping mrouter [vlan number ] Parameters vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For comma ...

  • Dell 9.8(0.0) - page 833

    21 Interfaces The Dell Networking OS supports the interface configuration commands described in this chapter. This chapter contains the following sections: • Basic Interface Commands • EIS Commands • Port Channel Commands • UDP Broadcast Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces. clear c ...

  • Dell 9.8(0.0) - page 834

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a tunnel interface, enter the keyword tunnel . The range is from 1 to 16383. vrrp [[ipv6] vrid ] (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To clear the counters of VRRP groups on all IPv6 interfaces, enter i ...

  • Dell 9.8(0.0) - page 835

    Example Dell#clear counters Clear counters on all interfaces [confirm] Related Commands mac learning-limit — allows aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. show interfaces — displays information on the interfaces. clear dampening Clear the dampening counters on all the interfaces or jus ...

  • Dell 9.8(0.0) - page 836

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Example Dell#clear dampening tegigabitethernet 1/10 Clear dampening counters on TeGi 1/10 [confirm] y Dell# Related Commands show interfaces dampening — displays interface dampening information. dampening — configures ...

  • Dell 9.8(0.0) - page 837

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information With each flap, the sy ...

  • Dell 9.8(0.0) - page 838

    Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19 ...

  • Dell 9.8(0.0) - page 839

    Parameters half Enter the keyword half to set the Management interface to transmit only in one direction. full Enter the keyword full to set the Management interface to transmit in both directions. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer t ...

  • Dell 9.8(0.0) - page 840

    Parameters rx on Enter the keywords rx on to process the received flow control frames on this port. rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from the port to the connected device when a higher rate of traffic is received. tx off Enter the keywords ...

  • Dell 9.8(0.0) - page 841

    The pause: • Starts when either the packet pointer or the buffer threshold is met (whichever is met first). When the discard threshold is met, packets are dropped. • Ends when both the packet pointer and the buffer threshold fall below 50% of the threshold settings. The discard threshold defines when the interface starts dropping the packet on ...

  • Dell 9.8(0.0) - page 842

    show interfaces — displays the negotiated flow control parameters. interface Configure a physical interface on the switch. Z9500 Syntax interface interface range Parameters interface Enter one of the following keywords and slot/port or number information: • For a null interface, enter the keyword null then the slot/port information. The Null in ...

  • Dell 9.8(0.0) - page 843

    Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Usage Information You cannot delete a physical interface. By default, physical interfaces are disabled ( shutdown ) and are not assig ...

  • Dell 9.8(0.0) - page 844

    Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on th ...

  • Dell 9.8(0.0) - page 845

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 846

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 847

    Parameters interface, interface,... Enter the keywords interface range and one of the interfaces — slot/port, port-channel, or VLAN number. Select the range of interfaces for bulk configuration. You can enter up to six comma-separated ranges. Spaces are not required between the commas. Comma-separated ranges can include VLANs, port-channels, and ...

  • Dell 9.8(0.0) - page 848

    Version Description 6.1.1.0 Introduced on the E-Series. Usage Information When creating an interface range, interfaces appear in the order they are entered; they are not sorted. The command verifies that interfaces are present (physical) or configured (logical). Important Points to Remember: • Bulk configuration is created if at least one interfa ...

  • Dell 9.8(0.0) - page 849

    Example (Multiple Range) This example shows how to use commas to add different interface types to the range enabling all 10-Gigabit Ethernet interfaces in the range 2/1 to 2/23 and both 10-Gigabit Ethernet interfaces 1/1 and 1/2. Dell(config-if)# interface range tengigabitethernet 2/1-23, tengigabitethernet 1/1-2 Dell(config-if-range)# no shutdown ...

  • Dell 9.8(0.0) - page 850

    • For a Tunnel interface, enter the keyword tunnel then the tunnel ID. The range is from 1 to 16383. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Net ...

  • Dell 9.8(0.0) - page 851

    interface range macro name – runs an interface range macro. interface range macro name Run the interface-range macro to automatically configure the pre-defined range of interfaces. Z9500 Syntax interface range macro name Parameters name Enter the name of an existing macro. Defaults none Command Modes CONFIGURATION Command History This guide is pl ...

  • Dell 9.8(0.0) - page 852

    interface vlan Configure a VLAN. You can configure up to 4094 VLANs. Z9500 Syntax interface vlan vlan-id Parameters vlan-id Enter a number as the VLAN Identifier. The range is 1 to 4094. Defaults Not configured, except for the Default VLAN, which is configured as VLAN 1. Command Modes CONFIGURATION Command History Version Description 9.2(1.0) Intro ...

  • Dell 9.8(0.0) - page 853

    keepalive Send keepalive packets periodically to keep an interface alive when it is not transmitting data. Z9500 Syntax keepalive [ seconds ] To stop sending keepalive packets, use the no keepalive command. Parameters seconds (OPTIONAL) For interfaces with PPP encapsulation enabled, enter the number of seconds between keepalive packets. The range i ...

  • Dell 9.8(0.0) - page 854

    linecard portmode Split a single 40G port into four 10G ports on the switch. Z9500 Syntax linecard slot-id port number portmode quad Parameters linecard slot-id Enter the slot ID of a Z9500 line card to reset. The range of slot IDs is from 0 to 2. number Enter the port number of the 40G port to be split. A 40G port number is a multiple of 4; for ex ...

  • Dell 9.8(0.0) - page 855

    Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For the management port, enter the keyword managementethernet then the slot (0 or 1) and the port (0). • For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. • For a 10-Gigabit Ethernet interface, e ...

  • Dell 9.8(0.0) - page 856

    Key Description monitor time Displays the amount of time since the monitor interface command was entered. time Displays the amount of time the chassis is up (since last reboot). m Change the view from a single interface to all interfaces on the line card or visa-versa. c Refresh the view. b Change the counters displayed from Packets on the interfac ...

  • Dell 9.8(0.0) - page 857

    Fo 2/52 Down 0 0 0 0 Fo 2/56 Down 0 0 0 0 Fo 2/60 Down 0 0 0 0 Fo 2/64 Down 0 0 0 0 Fo 2/68 Down 0 0 0 0 Fo 2/72 Down 0 0 0 0 Fo 2/76 Down 0 0 0 0 Fo 2/80 Down 0 0 0 0 Fo 2/84 Down 0 0 0 0 Fo 2/88 Down 0 0 0 0 Fo 2/92 Down 0 0 0 0 Fo 2/96 Down 0 0 0 0 m - Change mode c - Clear screen b - Display bytes r - Display pkts/bytes per sec l - Page up a - ...

  • Dell 9.8(0.0) - page 858

    0 12 0 Fo 2/36 Down 0 0 0 0 Fo 2/40 Up 0 0 13 0 Fo 2/44 Up 0 0 12 0 Ma 0/0 Down 17 0 1 0 m - Change mode c - Clear screen b - Display bytes r - Display pkts/bytes per sec l - Page up a - Page down T - Increase refresh interval t - Decrease refresh interval q - Quit Dell# monitor interface managementethernet 0/0 Dell Networking operating system upti ...

  • Dell 9.8(0.0) - page 859

    pps 0 Output underruns: 0 0 pps 0 Output throttles: 0 0 pps 0 m - Change mode c - Clear screen l - Page up a - Page down T - Increase refresh interval t - Decrease refresh interval q - Quit mtu Set the link maximum transmission unit (MTU) (frame size) for an Ethernet interface. Z9500 Syntax mtu value To return to the default MTU value, use the no m ...

  • Dell 9.8(0.0) - page 860

    When you enter the no mtu command, the system reduces the IP MTU value to 1536 bytes. Link MTU and IP MTU considerations for port channels and VLANs are as follows. port channels: • All members must have the same link MTU value and the same IP MTU value. • The port channel link MTU and IP MTU must be less than or equal to the link MTU and IP MT ...

  • Dell 9.8(0.0) - page 861

    Defaults non-hybrid Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2( ...

  • Dell 9.8(0.0) - page 862

    Example Dell(conf-if-vl-20)#do show interfaces switchport Name: TenGigabitEthernet 2/0 802.1QTagged: Hybrid Vlan membership: Vlan 10, Vlan 20 Native VlanId: 10 Dell(conf-if-vl-20)# Example (Vlan) Dell(conf-if-vl-20)#interface vlan 10 Dell(conf-if-vl-10)#no untagged te 2/0 Dell(conf-if-vl-10)#interface vlan 20 Dell(conf-if-vl-20)#no tagged te 2/0 De ...

  • Dell 9.8(0.0) - page 863

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced Usage Information The output of the show interfaces command displays the configured rate int ...

  • Dell 9.8(0.0) - page 864

    Version Description 7.7.1.0 Introduced on the S-Series. Usage Information Resetting is a soft reboot, including flushing the forwarding tables. Example Stack MAC : 00:01:e8:8b:1a:36 Reload-Type : normal-reload [Next boot : normal-reload] -- Stack Info -- Unit UnitType Status ReqTyp CurTyp Version Ports ---------------------------------------------- ...

  • Dell 9.8(0.0) - page 865

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. Example Dell(conf-if)#show conf ! interface TenGigabitEthernet 1/7 no ip address switchport no shutdown Dell(conf-if)# show config (from INTERFACE RANGE mode) Display the bulk configured interfaces ( interface range ). Z9500 Syntax show config Command Modes ...

  • Dell 9.8(0.0) - page 866

    switchport no shutdown Dell(conf-if-range-te-1/1-2)# show interfaces Display information on a specific physical interface or virtual interface, or the interfaces of the same type on a line card. Z9500 Syntax show interfaces [ interface ] [linecard slot-id ] Parameters interface Enter one of the following keywords and slot/port or number information ...

  • Dell 9.8(0.0) - page 867

    Version Description 9.1(0.0) Updated ManagementEthernet output to include two global IPv6 addresses on S4810 and Z9000 and added output example showing OpenFlow instance ID. 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. 8.3.11.4 Output expanded to support eSR4 optics in Z9000. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 ...

  • Dell 9.8(0.0) - page 868

    Line Description Pluggable media present... Present pluggable media wavelength, type, and rate. The error scenarios are: • Wavelength, Non-qualified — Dell Force10 ID is not present, but wavelength information is available from XFP or SFP serial data • Wavelength, F10 unknown—Dell Force10 ID is present, but not able to determine the optics ...

  • Dell 9.8(0.0) - page 869

    Line Description – CRC = packets with CRC/FCS errors – overrun = number of packets discarded due to FIFO overrun conditions – discarded = the sum of runts, giants, CRC, and overrun packets discarded without any processing Output Statistics: Displays output statistics sent out of the interface including: • Number of packets, bytes, and under ...

  • Dell 9.8(0.0) - page 870

    byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023- byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collision ...

  • Dell 9.8(0.0) - page 871

    0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 01:21:35 TenGigabitEthernet 2/1 is down, line protocol is down Hardware is DellForce10Eth, address is 74:86: ...

  • Dell 9.8(0.0) - page 872

    Queueing strategy: fifo Time since last interface status change: 01:22:55 Example (ManagementE thernet Interface with two IPv6 addresses) Dell# show interfaces managementethernet 0/0 ManagementEthernet 0/0 is up, line protocol is up Hardware is DellForce10Eth, address is 00:01:e8:a0:bf:f3 Current address is 00:01:e8:a0:bf:f3 Pluggable media not pre ...

  • Dell 9.8(0.0) - page 873

    show inventory (S-Series and Z-Series) – displays the S-Series and Z-Series switch types, components (including media), Dell Networking OS version including hardware identification numbers, and configured protocols. show ip interface – displays Layer 3 information about the interfaces. show range – displays all interfaces configured using the ...

  • Dell 9.8(0.0) - page 874

    byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023- byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collision ...

  • Dell 9.8(0.0) - page 875

    Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces dampening Display interface dampening information. Z9500 Syntax show interfaces dampening [[ interface ] [linecard slot-id ] [summary] [detail]] Parameters interface (Optional) Enter one of the following keywords and slot ...

  • Dell 9.8(0.0) - page 876

    Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Example Dell# show interfaces dampening tengigabitethernet 2 Interface Supp Flaps Penalty Half-Life Reuse Suppress Max-Sup State Te 2 ...

  • Dell 9.8(0.0) - page 877

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 878

    Series line cards support both full-duplex and half-duplex 1000BaseT. Phy Specific Control Values are: • 0 - Manual MDI • 1 - Manual MDIX • 2 - N/A • 3 - Auto MDI/MDIX Phy Specific Status Displays PHY-specific status information. Cable length represents a rough estimate in meters: • 0 - < 50 meters • 1 - 50 - 80 meters • 2 - 80 - 1 ...

  • Dell 9.8(0.0) - page 879

    ParallelDetectionFault: False ... Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces status To display status information on a specific interface only, display a summary of interface information or specify a line card slot and interface. Z9500 Syntax show interfaces [ int ...

  • Dell 9.8(0.0) - page 880

    Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Example Dell#show interfaces status Port Description Status Speed Duplex Vlan Te 2/ ...

  • Dell 9.8(0.0) - page 881

    Fo 2/176 Down 40000 Mbit Auto -- Fo 2/180 Down 40000 Mbit Auto -- Fo 2/184 Down 40000 Mbit Auto -- Fo 2/188 Down 40000 Mbit Auto -- Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces vlan Display VLAN statistics. Z9500 Syntax show interfaces vlan { vlan-id } [LINE] {descr ...

  • Dell 9.8(0.0) - page 882

    show range Display all interfaces configured using the interface range command. Z9500 Syntax show range Command Modes INTERFACE RANGE (config-if-range) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the ...

  • Dell 9.8(0.0) - page 883

    show running-config ecmp-group Display interfaces, LAG, or LAG link bundles being monitored for uneven traffic distribution using the ecmp-group monitoring enable command. The ECMP group could have a LAG or a list of 10G/40 interfaces (not just LAG link-bundles). Z9500 Syntax show running-config ecmp-group Defaults Disabled. Command Modes CONFIGURA ...

  • Dell 9.8(0.0) - page 884

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information The shutdown command marks a physical interface as unavaila ...

  • Dell 9.8(0.0) - page 885

    auto Enter the keyword auto to set the interface to auto- negotiate its speed. Defaults auto Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history ...

  • Dell 9.8(0.0) - page 886

    Parameters backup interface Use this option to configure a redundant Layer 2 link without using Spanning Tree. The keywords backup interface configures a backup port so that if the primary port fails, the backup port changes to the up state. If the primary later comes up, it becomes the backup. tengigabit Enter the keyword tengigabit if the backup ...

  • Dell 9.8(0.0) - page 887

    When you enter the switchport command, the interface is automatically added to the default VLAN. To use the switchport backup interface command on a port, first enter the switchport command. For more information, refer to the “Configuring Redundant Links” section in the “Layer 2” chapter of the Dell Networking OS Configuration Guide . Relat ...

  • Dell 9.8(0.0) - page 888

    Defaults None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on t ...

  • Dell 9.8(0.0) - page 889

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, an ...

  • Dell 9.8(0.0) - page 890

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, an ...

  • Dell 9.8(0.0) - page 891

    show management application pkt-fallback-cntr Display the number of packets for each application type that have been rerouted to the default routing table due to management port or route lookup failure. Z9500 Syntax show management application pkt—fallback-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-spe ...

  • Dell 9.8(0.0) - page 892

    NOTE: The implementation of LAG or Port Channel requires that you configure a LAG on both switches manually. For information about the link aggregation control protocol (LACP) for dynamic LAGs, refer to the Link Aggregation Control Protocol (LACP) chapter. For more information about configuring and using Port Channels, refer to the Dell Networking ...

  • Dell 9.8(0.0) - page 893

    Usage Information Use the interface port-channel command to access this command. You cannot add an interface to a Port Channel if the interface contains an IP address in its configuration. Only the shutdown , description , mtu , and ip mtu commands can be configured on an interface if it is added to a Port Channel. The mtu and ip mtu commands are o ...

  • Dell 9.8(0.0) - page 894

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 895

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series ExaScale. 7.6.1.0 Introduced on S-Series. 7.5.1.0 Introduced on C-Series. 6.2.1.0 Introduced on E-Series. Usage Information Port Channel interfaces are logical interfaces ...

  • Dell 9.8(0.0) - page 896

    shutdown — disables/enables the port channel. minimum-links Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the LAG to be also in “oper up” status. Z9500 Syntax minimum-links number Parameters number Enter the number of links in a LAG that must be in “oper up” status. The range is fro ...

  • Dell 9.8(0.0) - page 897

    port-channel failover-group To configure a LAG failover group, access PORT-CHANNEL FAILOVER-GROUP mode. Z9500 Syntax port-channel failover-group To remove all LAG failover groups, use the no port-channel failover-group command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about o ...

  • Dell 9.8(0.0) - page 898

    show config Display the current configuration of the selected LAG. Z9500 Syntax show config Command Modes INTERFACE PORTCHANNEL Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS vers ...

  • Dell 9.8(0.0) - page 899

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 900

    Field Description Queueing strategy. States the packet queuing strategy. FIFO means first in first out. packets input... Displays the number of packets and bytes into the interface. Input 0 IP packets... Displays the number of packets with IP headers, VLAN tagged headers, and MPLS headers. The number of packets may not add correctly because a VLAN ...

  • Dell 9.8(0.0) - page 901

    Dell# User Information The following describes the show interfaces port-channel brief command shown in the following example. Field Description LAG Lists the port channel number. Mode Lists the mode: • L3 — for Layer 3 • L2 — for Layer 2 Status Displays the status of the port channel. • down — if the port channel is disabled ( shutdown ...

  • Dell 9.8(0.0) - page 902

    Parameters outgoing-port- channel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information. • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. incoming- interface interface Enter the keywords incoming-interface then the interface type a ...

  • Dell 9.8(0.0) - page 903

    Usage Information Because this command calculates based on a Layer 2 hash algorithm, use this command to display flows for switched Layer 2 packets, not for routed packets (use the show ip flow command to display routed packets). The show port-channel-flow command returns the egress port identification in a given port-channel if a valid flow is ent ...

  • Dell 9.8(0.0) - page 904

    • Line-card slot 0 uses three NPUs numbered 0 to 2. • Line-card slot 1 uses four NPUs numbered 0 to 3. • Line-card slot 2 uses four NPUs numbered 0 to 3. SFM NPUs are numbered 0 to 5. Line-card and SFM NPUs use HiGig port channels to transmit data. • An SFM NPU uses 11 HiGig port channels, one port channel to transmit data to each line-card ...

  • Dell 9.8(0.0) - page 905

    Example Dell# clear hardware linecard 0 hg-stats unit 0 port 59 Dell# show hardware linecard 0 hg-stats unit 0 port 59 Higig Port Statistics: HiGigabitEthernet 0/0/59, Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023- byte pkts 0 Multicasts, 0 Broa ...

  • Dell 9.8(0.0) - page 906

    Command Mode CONFIGURATION Command History Version Description 9.2(1.0) Introduced on the Z9500 switch. 9.3.0.0 Introduced on the Z9000 switch. Usage Information You can configure HiGig link bundle monitoring so that a system log message or an SNMP trap is generated when traffic distribution in a bundle is uneven. The formula that determines uneven ...

  • Dell 9.8(0.0) - page 907

    Parameters percentage Trigger threshold (in percentage of link-bundle bandwidth) at which an SNMP trap is generated. Valid values are 1 to 90. Command Modes CONFIGURATION Command History Version Description 9.2.1.0 Introduced on the Z9500 switch. 9.3.0.0 Introduced on the Z9000 platform. Defaults The default trigger-threshold value is 60. Usage Inf ...

  • Dell 9.8(0.0) - page 908

    Command Modes • EXEC • EXEC Privilege Command History Version Description 9.2.1.0 Introduced on the Z9500 switch. 9.3.0.0 Added support for the hg-stats option on the Z9000 platform. Example (Line- card HiGig Port) Dell# show hardware linecard 0 hg-stats unit 0 port 59 Higig Port Statistics: HiGigabitEthernet 0/0/59, Input Statistics: 0 packets ...

  • Dell 9.8(0.0) - page 909

    Example (SFM HiGig Port) Dell# show hardware sfm 5 hg-stats port 19 Higig Port Statistics: HiGigabitEthernet 3/5/19, Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023- byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 over ...

  • Dell 9.8(0.0) - page 910

    Command History Version Description 9.2.(1.0) Introduced on the Z9500 switch. 9.3.0.0 Introduced on the Z9000 switch. Usage Information The following table illustrates the fields displayed in the output of this command: Field Description Link-bundle trigger threshold Percentage value of link-bundle bandwidth that serves as the threshold for marking ...

  • Dell 9.8(0.0) - page 911

    snmp-server enable traps hg-lbm Enable the generation of SNMP traps and notifications when HiGig link-bundle monitoring is enabled. Z9500 Syntax snmp-server enable traps hg-lbm Parameters hg-lbm Enter the keyword hg-lbm to enable traps for HiGig link- bundle monitoring. Command Modes CONFIGURATION mode Command History Version Description 9.2.1.0 In ...

  • Dell 9.8(0.0) - page 912

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 913

    Defaults none Command Modes INTERFACE (config-if) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z ...

  • Dell 9.8(0.0) - page 914

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 915

    22 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: • Authentication He ...

  • Dell 9.8(0.0) - page 916

    To delete a transform set, use the no crypto ipsec transform-set name {ah-authentication {md5|sha1|null} | esp-authentication {md5| sha1|null} | esp-encryption {3des|cbc|des|null}} command. Parameters name Enter the name for the transform set. ah- authentication Enter the keywords ah-authentication then the transform type of operation to apply to t ...

  • Dell 9.8(0.0) - page 917

    Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the Z9000, S4810, and S4820T. Usage Information • Both sides of the link must specify the same transform set. • You can create up to 64 transform sets. Example Dell(conf)#int ten 0/4 Dell(conf-if-te-0/4)#ipv6 address 200:1::/64 eui64 Dell(conf)#int ten 0/6 Dell(conf-if ...

  • Dell 9.8(0.0) - page 918

    Usage Information This command creates a crypto policy entry and enters the crypto policy configuration mode for configuring the flow parameters. Example Dell(conf)#crypto ipsec policy West 10 ipsec-manual Dell(conf-crypto-policy)# management crypto-policy Apply the crypto policy to management traffic. Z9500 Syntax management crypto-policy name To ...

  • Dell 9.8(0.0) - page 919

    To remove the match filter for the crypto map, use the no match seq-num tcp [ source ip address | ipv6 address { mask } { source-port number }] [ destination ip address | ipv6 address { mask } { destination-port number }] command. Parameters seq-num Enter the match command sequence number. source ip- address | ipv6 address Enter the keyword source ...

  • Dell 9.8(0.0) - page 920

    session-key Specify the session keys used in the crypto policy entry. Z9500 Syntax session-key {inbound | outbound} {ah spi hex-key-string | esp spi encrypt hex-key-string auth hex-key-string To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters name Enter the name f ...

  • Dell 9.8(0.0) - page 921

    show crypto ipsec transform-set Display the transform set configuration. Z9500 Syntax show crypto ipsec transform-set name Parameters name Enter the name of the transform set. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refer ...

  • Dell 9.8(0.0) - page 922

    Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the Z9000, S4810, and S4820T. Example Dell#show crypto ipsec policy Policy name : West Policy refcount : 1 Sequence Num : 10 SA Mode : IPSEC-MANUAL Transform-Set Name : dallas Peer IP Address : Inbound AH SPI : 0 Inbound ESP Auth SPI : 0 Inbound ESP Encry SPI : 256 Inbound ...

  • Dell 9.8(0.0) - page 923

    Destination address : a::2 Destination mask : /128 Destination port : 21 source-interface name : source-interface num : Match sequence Num : 3 Protocol type : tcp IP or IPv6 : IPv6 Source address : a::1 Source mask : /128 Source port : 21 Destination address : a::2 Destination mask : /128 Destination port : 0 source-interface name : source-interfac ...

  • Dell 9.8(0.0) - page 924

    23 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the switch. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Z9500 Syntax arp ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters ip-address Enter an ...

  • Dell 9.8(0.0) - page 925

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduc ...

  • Dell 9.8(0.0) - page 926

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of A ...

  • Dell 9.8(0.0) - page 927

    arp retries Set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. Z9500 Syntax arp retries number Parameters number Enter the number of retries. The range is from 5 to 20. The default is 5 . Defaults 5 Command Modes CONFIGURATION Command History This guide is platform-specific. For command inf ...

  • Dell 9.8(0.0) - page 928

    Parameters seconds Enter the number of minutes. The range is from 0 to 35790. The default is 240 minutes . Defaults 240 minutes (4 hours) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a l ...

  • Dell 9.8(0.0) - page 929

    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. ip ip-address (OPTIONAL) Enter the keyword ip then the IP address of t ...

  • Dell 9.8(0.0) - page 930

    clear host Remove one or all dynamically learned host table entries. Z9500 Syntax clear host name Parameters name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Netw ...

  • Dell 9.8(0.0) - page 931

    Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the ...

  • Dell 9.8(0.0) - page 932

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands ip route — assig ...

  • Dell 9.8(0.0) - page 933

    Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands show ip traffic — displays IP traffic statistics. clear tcp statistics Clear TCP counters. Z9500 Syntax clear tcp statistics ...

  • Dell 9.8(0.0) - page 934

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands show tcp statistics — displays TCP traffic statistics. debug arp View information on ARP transactions. Z9500 Syntax debug arp [ interface ] [count value ] To stop debugging ARP transactions, use the no debug arp command. Parameters interfa ...

  • Dell 9.8(0.0) - page 935

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series ExaScale ...

  • Dell 9.8(0.0) - page 936

    Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series. Example Dell#debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) recei ...

  • Dell 9.8(0.0) - page 937

    debug ip icmp View information on the internal control message protocol (ICMP). Z9500 Syntax debug ip icmp [ interface ] [count value ] To disable debugging, use the no debug ip icmp command. Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For the Management interface, enter the keyword Manageme ...

  • Dell 9.8(0.0) - page 938

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option. Example ICMP: echo request rcvd from src 40.40.40.40 ICMP: src 40.40.40.40, dst 40.40.40.40, echo reply ICMP: src 40.40.40.40, dst 40.40.40.40, echo reply ICMP: echo request sent to ...

  • Dell 9.8(0.0) - page 939

    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-sp ...

  • Dell 9.8(0.0) - page 940

    Field Description broad/multicast proto, unroutable TCP src= Displays the source and destination ports, the sequence number, the acknowledgement number, and the window size of the packets in that TCP packets. UDP src= Displays the source and destination ports for the UDP packets. ICMP type= Displays the ICMP type and code. IP Fragment States that i ...

  • Dell 9.8(0.0) - page 941

    • IP protocol number: from 0 to 255 • Internet control message protocol ( icmp ) but not the ICMP message type (from 0 to 255) • Any internet protocol ( ip ) • Transmission Control Protocol ( tcp ) but not on the rst , syn , or urg bits • User Datagram Protocol ( udp ) In the case of ambiguous access control list rules, the debug ip packe ...

  • Dell 9.8(0.0) - page 942

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 943

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. ip domain-list Configure names to complete unqualified host names. Z9500 Syntax ip domain-list name To remove t ...

  • Dell 9.8(0.0) - page 944

    Version Description 7.5.1.0 Introduced on the C-Series. Usage Information To configure a list of possible domain names, configure the ip domain-list command up to six times. If you configure both the ip domain-name and ip domain-list commands, the software tries to resolve the name using the ip domain-name command. If the name is not resolved, the ...

  • Dell 9.8(0.0) - page 945

    Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information To fully enable DNS, also specify one or more domain name servers with the ip name-server command. The system does not support sending DNS queries over a VLAN. DN ...

  • Dell 9.8(0.0) - page 946

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information You can only configure one domain name with the ip domain-n ...

  • Dell 9.8(0.0) - page 947

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-S ...

  • Dell 9.8(0.0) - page 948

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 949

    ip address Enter an IP address, in dotted decimal format, to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networkin ...

  • Dell 9.8(0.0) - page 950

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 951

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 6.1.1.0 Introduced on the E-Series. Usage Information When you enter the no mtu command, the system reduces the ip mtu value to 1536 bytes. To return the IP MTU value to the default, ...

  • Dell 9.8(0.0) - page 952

    Layer 2 Overhead Difference between Link MTU and IP MTU Tagged Packet with VLAN-Stack Header 26 bytes Related Commands mtu — sets the link MTU for an Ethernet interface. ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Z9500 Syntax ip name-server ipv4-address [ ipv ...

  • Dell 9.8(0.0) - page 953

    Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The system does not support sending DNS queries over a VLAN. DNS queries are sent out on all other interfaces, including the Management port. You can separately configure both IPv4 and IPv6 domain name servers. Related Commands ipv6 name-se ...

  • Dell 9.8(0.0) - page 954

    Related Commands show ip interface — displays the interface routing status and configuration. ip route Assign a static route to the switch. Z9500 Syntax ip route { destination mask { ip-address | interface [ slot/port ] | [tunnel tunnel-id ] [ distance ] | [permanent] | tag tag-value }} To delete a specific static route, use the no ip route desti ...

  • Dell 9.8(0.0) - page 955

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Added ...

  • Dell 9.8(0.0) - page 956

    ip source-route Enable the system to forward IP packets with source route information in the header. Z9500 Syntax ip source-route To drop packets with source route information, use the no ip route-source command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platfo ...

  • Dell 9.8(0.0) - page 957

    Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8 ...

  • Dell 9.8(0.0) - page 958

    from the LPM routing table (RTM). To enable storage of IPv4 route prefixes in the LPM table, disable this setting by entering the no ipv4 unicast-host-route command. Example Dell(conf)#ipv4 unicast-host-route Warning: Command will take effect for existing routes only when IPv4 route prefixes are cleared from RTM Dell(conf)#no ipv4 unicast-host-rout ...

  • Dell 9.8(0.0) - page 959

    returns a 3-bit index indicating which port the packet should be forwarded. • source-mac — Uses the source MAC address, VLAN, Ethertype, source module ID and source port ID fields to hash. The hashing mechanism returns a 3-bit index indicating which port the packet should be forwarded. tcp-udp enable Enter the keywords to distribute traffic bas ...

  • Dell 9.8(0.0) - page 960

    Related Commands hash-algorithm ecmp — changes the hash algorithm across an ECMP. management route Configure a static route that points to the Management interface or a forwarding router. Z9500 Syntax management route {{ ip-address mask | { ipv6-address prefix- length }} { forwarding-router-address | managementethernet | fortyGigE | vlan | tengig ...

  • Dell 9.8(0.0) - page 961

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for forty gigabit, vlan, and tengigabit ethernet interf ...

  • Dell 9.8(0.0) - page 962

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. • For a port channel interface, enter the keywords port- channel then a nu ...

  • Dell 9.8(0.0) - page 963

    Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.8.1.0 Augmented to display local ARP entries learned from p ...

  • Dell 9.8(0.0) - page 964

    Internet 192.2.1.247 1 00:00:c0:02:01:02 Te 2/13 - CP Internet 192.2.1.246 1 00:00:c0:02:01:02 Te 2/13 - CP Internet 192.2.1.245 1 00:00:c0:02:01:02 Te 2/13 - CP Example (Private VLAN) NOTE: In this example, Line 1 shows community VLAN 200 (in primary VLAN 10) in a PVLAN. Line 2 shows primary VLAN 10. Dell#show arp Protocol Address Age(min) Hardwar ...

  • Dell 9.8(0.0) - page 965

    show arp retries Display the configured number of ARP retries. Z9500 Syntax show arp retries Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking ...

  • Dell 9.8(0.0) - page 966

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Added support for IPv6 addresses. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following ...

  • Dell 9.8(0.0) - page 967

    Name/address lookup uses static mappings Name servers are not set Host Flags TTL Type Address -------- ----- ---- ---- ------- ks (perm, OK) - IP 2.2.2.2 4200-1 (perm, OK) - IP 192.68.69.2 1230-3 (perm, OK) - IP 192.68.99.2 ZZr (perm, OK) - IP 192.71.18.2 Z10-3 (perm, OK) - IP 192.71.23.1 Dell# Related Commands traceroute — views the DNS resoluti ...

  • Dell 9.8(0.0) - page 968

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.1.1.2 Introduced on the E-Series ExaScale E600i. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.5.1.0 ...

  • Dell 9.8(0.0) - page 969

    Example Dell#show ip cam linecard 1 port-set 0 Index Destination EC CG V C Next-Hop VId Mac-Addr Port ------ ----------------------------------- ---- ------------- 3276 6.6.6.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP 3277 5.5.5.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP 3278 4.4.4.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP 3279 3.3.3.2 0 ...

  • Dell 9.8(0.0) - page 970

    8 0 1312 7 0 1312 6 0 1312 5 0 1312 4 0 1312 3 0 1312 2 0 1312 1 0 1312 0 0 8 Dell# show ip fib linecard View all forwarding information base (FIB) entries. Z9500 Syntax show ip fib linecard slot-id [ ip-address/prefix-list | summary] Parameters slot-id Enter the slot ID of the line card. The range of Z9500 slot IDs is from 0 to 2. ip-address mask ...

  • Dell 9.8(0.0) - page 971

    Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show ip fib command shown in the following example. Field Description Destination Lists the destination IP address. Gateway Displays either the word “direct” and an int ...

  • Dell 9.8(0.0) - page 972

    show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface. Z9500 Syntax show ip flow interface interface {source-ip address destination-ip address } {protocol number [tcp | udp]} {src-port number destination-port number } Parameters interface interface Enter the keyword interface then one of the following interfa ...

  • Dell 9.8(0.0) - page 973

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information This command provides egress port information for a given IP flow. This information is useful in identifying which inte ...

  • Dell 9.8(0.0) - page 974

    • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. • For a port channel interface, enter the keywords port- channel then a number. The ran ...

  • Dell 9.8(0.0) - page 975

    Version Description pre-6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show ip interface command shown in the following example. Lines Description TenGigabitEthern et 1/1... Displays the interface’s type, slot/port, and physical and line protocol status. Internet address... States whether an IP address is assign ...

  • Dell 9.8(0.0) - page 976

    Fields Description Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface. Example (Brief) Dell#show ip interface brief Interface IP-Address OK? Method Status Protocol TenGigabitEthernet 1/0 unassigned NO Manual administratively down dow ...

  • Dell 9.8(0.0) - page 977

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 978

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Regular evaluation optimization enabled/disabled added to display output. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example Dell#show ip protoco ...

  • Dell 9.8(0.0) - page 979

    longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. list prefix-list (OPTIONAL) Enter the keyword list and the name of a configured prefix list. For more information, refer to the show ip route list command. protocol (OPTIONAL) Enter the name of a routing protocol ( bgp , isis , ospf , rip ) or the ...

  • Dell 9.8(0.0) - page 980

    Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show ip route all command in the following example. Field Description (undefined) Identifies the type of route: • C = connected • S ...

  • Dell 9.8(0.0) - page 981

    type 1 N2- OSPF NSSA external type 2, E1 - OSPF external type 1 E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1 L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default >- non-active route + - summary route Gateway of last resort is not set Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------- R 3 ...

  • Dell 9.8(0.0) - page 982

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example Dell#show ip route list test Code ...

  • Dell 9.8(0.0) - page 983

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 984

    Total 2 non-active route(s) using 128 bytes Dell> Related Commands show ip route — displays information about the routes found in the switch. show ip traffic View IP traffic statistics on Z9500 CPUs, including ICMP, UDP, TCP and ARP counters. Z9500 Syntax show ip traffic {all | cp | rp} Parameters all (OPTIONAL) Enter the keyword all to view I ...

  • Dell 9.8(0.0) - page 985

    Usage Information The following describes the show ip traffic summary shown in the following example. Keyword Definition unknown protocol... No receiver for these packets. Counts packets whose protocol type field is not recognized by the system. not a gateway... Packets can not be routed; the host/network is unreachable. security failures... Counts ...

  • Dell 9.8(0.0) - page 986

    • IP Statistics: Mcast: Sent: Object = f10McastPktSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.4 • ARP Statistics: Rcvd: Request: Object = f10ArpReqRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.1 • ARP Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3 • ARP Statistics: Sent: Request: Object = f10ArpReqSent, OIDs = 1.3. ...

  • Dell 9.8(0.0) - page 987

    show tcp statistics Display statistical information about TCP traffic transmitted on Z9500 CPUs. Z9500 Syntax show tcp statistics {all | cp | rp} Parameters all Enter the keyword all to view all TCP statistics on Z9500 CPUs. cp Enter the keyword cp to view TCP statistics only from the Control Processor. rp Enter the keyword rp1 to view TCP statisti ...

  • Dell 9.8(0.0) - page 988

    Field Description 0 checksum error... Displays the number of packets received with the following: • checksum errors • bad offset to data • too short 329 packets... Displays the number of packets and bytes received in sequence. 17 dup... Displays the number of duplicate packets and bytes received. 0 partially... Displays the number of partiall ...

  • Dell 9.8(0.0) - page 989

    Field Description 20 Total rxmt... Displays the number of times the switch tried to re-send data and the number of connections dropped during the TCP retransmit timeout period. 0 Keepalive.... Lists the number of keepalive packets in timeout, the number keepalive probes and the number of TCP connections dropped during keepalive. Example Dell#show t ...

  • Dell 9.8(0.0) - page 990

    24 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking operating system. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl comman ...

  • Dell 9.8(0.0) - page 991

    • L3 QoS (ipv4qos): 1 • L2 QoS (l2qos): 1 l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATIO ...

  • Dell 9.8(0.0) - page 992

    cam-acl-egress Allocate space for IPv6 egress ACLs. Z9500 Syntax cam-acl-egress {default | l2acl 1-4 ipv4acl 1-4 ipv6acl 0-4 } Parameters default Use the default CAM profile settings, and set the CAM as follows: • L2 ACL(l2acl): 1 • L3 ACL (ipv4acl: 1 • IPv6 L3 ACL (ipv6acl): 2 l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ...

  • Dell 9.8(0.0) - page 993

    Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10). Example Dell# Dell#configure Dell(conf)#cam-acl-egress ? default Reset Egress CAM ACL entries to default setting l2acl Set L2-ACL entries Dell(conf)#cam-acl-egress l2acl ? <1-4> Num ...

  • Dell 9.8(0.0) - page 994

    Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Version 9.5(0.1) Introduced on the Z9500. Version 9.4(0.0) Added support for flow-based moni ...

  • Dell 9.8(0.0) - page 995

    To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny arp { destination-mac-address mac-address-mask | any} vlan vlan-id { ip-address | any | opcode code-number } command. Parameters log (OPTIONAL) Enter the keyword log to enable the triggering of ACL ...

  • Dell 9.8(0.0) - page 996

    You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction ...

  • Dell 9.8(0.0) - page 997

    in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Version 9.5(0.1) Intr ...

  • Dell 9.8(0.0) - page 998

    address } [ bit ] [ operator port [ port ]] [count [byte]] [log [interval minutes ] [threshold-in-msgs [ count ]] [monitor] To remove this filter, you have two choices: • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no deny tcp { source address mask | any | host ipv6- address } { destination ...

  • Dell 9.8(0.0) - page 999

    ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are ...

  • Dell 9.8(0.0) - page 1000

    Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Version 9.5(0.1) Introduced on the Z9500. Version 9.4(0.0) Added support for flow-based moni ...

  • Dell 9.8(0.0) - page 1001

    ipv6 access-list Configure an access list based on IPv6 addresses or protocols. Z9500 Syntax ipv6 access-list access-list-name To delete an access list, use the no ipv6 access-list access-list-name command. Parameters access-list- name Enter the access list name as a string, up to 140 characters. Defaults All access lists contain an implicit “den ...

  • Dell 9.8(0.0) - page 1002

    ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Z9500 Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide ...

  • Dell 9.8(0.0) - page 1003

    of ACL logs is terminated with the seq , permit , or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describ ...

  • Dell 9.8(0.0) - page 1004

    permit icmp (for IPv6 ACLs) To allow all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax permit icmp { source address mask | any | host ipv6-address } { destination address | any | host ipv6-address } [ message-type ] [count [byte]] [log [interval minutes ] [threshold-in-msgs [ count ]] [monitor] To remove ...

  • Dell 9.8(0.0) - page 1005

    Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured th ...

  • Dell 9.8(0.0) - page 1006

    threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq , permit , or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval ...

  • Dell 9.8(0.0) - page 1007

    Related Commands permit (for Standard IPv6 ACLs) – configures a filter to forward IPv6 packets. permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp { source address mask | any | host ipv6-address } [ operator port [ port ]] { destination address | any | host ipv6- address } [ operator p ...

  • Dell 9.8(0.0) - page 1008

    Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new ...

  • Dell 9.8(0.0) - page 1009

    of ACL logs is terminate with the seq , permit , or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describi ...

  • Dell 9.8(0.0) - page 1010

    test cam-usage Verify that enough ACL CAM space is available for the IPv6 ACLs you have created. Z9500 Syntax test cam-usage service-policy input policy-map-name linecard { slot-id | all} Parameters input policy- map name Enter the name of the policy-map to be verified. linecard slot-id Enter the slot ID of the Z9500 line card, which contains the p ...

  • Dell 9.8(0.0) - page 1011

    Term Explanation Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for linecards and port-pipes in the chassis. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile. Estimated CAM per Port Estimates the amount of CAM ...

  • Dell 9.8(0.0) - page 1012

    25 IPv6 Basics IPv6 basic commands are supported on the Dell Networking operating system. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide . cam-ipv6 extended-prefix Enable LPM CAM pa ...

  • Dell 9.8(0.0) - page 1013

    Usage Information You can partition the LPM table to store extended IPv6 route prefixes with /65 to /128 mask lengths. LPM CAM partitioning requires a switch reload to take effect. To disable LPM CAM partitioning and return the number of the IPv6 /65-/128 route prefixes stored in Partition 1 to 0, enter the no cam-ipv6 extended-prefix command. clea ...

  • Dell 9.8(0.0) - page 1014

    clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Z9500 Syntax clear ipv6 route [vrf vrf-name ] {* | ipv6-address prefix- length } Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all route ...

  • Dell 9.8(0.0) - page 1015

    clear ipv6 mld_host Clear the IPv6 MLD host counters and reset the elapsed time. Z9500 Syntax clear ipv6 mld_host Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS ...

  • Dell 9.8(0.0) - page 1016

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.1(0.0) Updated Usage Information. 9.0.0.0 ...

  • Dell 9.8(0.0) - page 1017

    ipv6 address eui64 Configure IPv6 EUI64 address configuration on the interface. Z9500 Syntax ipv6 address { ipv6-address prefix-length } eui64 To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address { ipv6-address prefix-length } eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format the ...

  • Dell 9.8(0.0) - page 1018

    ipv6 control-plane icmp error-rate-limit Configure the maximum number of ICMP error packets per second that can be sent per second. Z9500 Syntax ipv6 control-plane icmp error-rate-limit {1-200} To restore the default value, use the no ipv6 control-plane icmp error- rate-limit command. Parameters pps Enter the maximum number of error packets generat ...

  • Dell 9.8(0.0) - page 1019

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 1020

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series TeraScale. ipv6 name-server Enter up to six IPv6 addresses of name servers. The order you enter the addresses d ...

  • Dell 9.8(0.0) - page 1021

    Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series TeraScale. Usage Information You can separately configure both IPv4 and IPv6 domain name servers. ipv6 nd dad attempts To perform duplicate addre ...

  • Dell 9.8(0.0) - page 1022

    ipv6 nd prefix Specify which IPv6 prefixes are included in Neighbor Advertisements. Z9500 Syntax ipv6 nd prefix { ipv6-prefix | prefix-length | default} [no- advertise] | [no-autoconfig] [no-rtr-address] [off-link] [lifetime { valid | infinite} { preferred | infinite}] Parameters ipv6-prefix Enter an IPv6 prefix. prefix-length Enter the prefix then ...

  • Dell 9.8(0.0) - page 1023

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.2.0 Introduced on the E-Series TeraScale, C-Series, and S- Series. Usage Information By default, all prefixes configured as addresses on the interface are advertised. This command allows con ...

  • Dell 9.8(0.0) - page 1024

    Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1025

    To remove the IPv6 route, use the no ipv6 route [vrf vrf-name ] ipv6- address prefix-length { ipv6-address | interface | interface ipv6-address } [ distance ] [tag value ] [permanent] [weight] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF. ipv6-address prefix-len ...

  • Dell 9.8(0.0) - page 1026

    permanent (OPTIONAL) Enter the keyword permanent to specify that the route is not to be removed, even if the interface assigned to that route goes down. NOTE: If you disable the interface with an IPv6 address associated with the keyword permanent , the route disappears from the routing table. weight weight- value Enter the keyword weight followed b ...

  • Dell 9.8(0.0) - page 1027

    You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect. Also, if a path corresponding to a static route (destination) has a non-zero weight assigned to it and other paths do not have any weight configured, then regular ECMP is used for ...

  • Dell 9.8(0.0) - page 1028

    Example Dell(conf)# ipv6 unicast-host-route Warning: Command will take effect for existing routes only when IPv6 route prefixes are cleared from RTM Dell(conf)#no ipv6 unicast-host-route Warning: Command will take effect for existing routes only when IPv6 route prefixes are cleared from RTM Dell(conf)# ipv6 unicast-routing Enable IPv6 Unicast routi ...

  • Dell 9.8(0.0) - page 1029

    Disabling unicast routing on an E-Series chassis causes the following behavior: • static and protocol learned routes are removed from RTM and from the CAM; packet forwarding to these routes is terminated • connected routes and resolved neighbors remain in the CAM and new IPv6 neighbors are still discoverable • additional protocol adjacencies ...

  • Dell 9.8(0.0) - page 1030

    show ipv6 cam linecard Displays the IPv6 CAM entries for the specified line card and port pipe. Z9500 Syntax show ipv6 cam linecard slot-id port-set {0-3} [summary | ipv6– address ] Parameters line card slot-id Enter the slot ID of the line card. The range of Z9500 slot IDs is from 0 to 2. port-set Enter the keyword port—set followed by the por ...

  • Dell 9.8(0.0) - page 1031

    Usage Information NOTE: If a route has a mask greater than 64, no output is displayed but an equivalent /64 entry is listed in the show ipv6 cam linecard {0–2} port-set {0-3} output. Similarly, if there is more than one ECMP object with a destination route that has a mask greater than 64, if the first 64 bits in the destination routes of the ECMP ...

  • Dell 9.8(0.0) - page 1032

    Number of CAM entries used by NBR entries = 0 Number of CAM entries used by Prefix entries = 1 Section Current Use Initial Size -------------------------------------- 128 0 147519 127 0 63 126 0 63 125 0 63 124 0 63 123 0 63 122 0 63 121 0 63 120 0 63 119 0 63 118 0 63 117 0 63 116 0 63 115 0 63 --More-- show ipv6 management-route Display the IPv6 ...

  • Dell 9.8(0.0) - page 1033

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Introduced on the C- and E-Series. 8.3.7.0 Introduced on the S4810. Example Dell#show ipv6 management-route IPv6 Destination Gateway State ---------------- ------- ----- 2001:34::0/64 ManagementEthernet 0/0 Connected 200 ...

  • Dell 9.8(0.0) - page 1034

    show ipv6 fib linecard View all FIB entries. Z9500 Syntax show ipv6 fib [vrf vrf-name ]linecard slot-id [summary | ipv6- address ] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to clear the neighbor corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default V ...

  • Dell 9.8(0.0) - page 1035

    Usage Information Host tables are not stored in CAM tables on S-Series platforms. Entries for camIndex displays as zero (0) on the show ipv6 fib linecard output for neighbor entries, such as address resolution protocol (ARP) entries. Example Dell# show ipv6 fib linecard 0 summary Total Number of Routes in the FIB database is 0 Total Number of Route ...

  • Dell 9.8(0.0) - page 1036

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Related Commands ipv6 nd dad attempts — Configure system to set the flow label field in the packets to zero. show ipv6 interface Display the status of interfaces configured for IPv6. Z9500 Syntax show ipv6 interface interface [linecard slot-id ] [brief] [config ...

  • Dell 9.8(0.0) - page 1037

    managementet hernet slot/ port (OPTIONAL) View information on an IPv6 Management port. Enter the slot number (0-1) and port number zero (0). loopback (OPTIONAL) View information for IPv6 Loopback interfaces. port-channel (OPTIONAL) View information for IPv6 port channels. tengigabitether net (OPTIONAL) View information for an IPv6 tengigabitetherne ...

  • Dell 9.8(0.0) - page 1038

    IPV6 is enabled Link Local address: fe80::7686:7aff:feff:6f08 Global Unicast address(es): 10:10:10:1::8, subnet is 10:10:10::/48 (MANUAL) Remaining lifetime: infinite Global Anycast address(es): Joined Group address(es): ff02::1 ff02::2 ff02::1:ff00:8 ff02::1:ffff:6f08 ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: ...

  • Dell 9.8(0.0) - page 1039

    ND reachable time is 27000 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 200 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated ...

  • Dell 9.8(0.0) - page 1040

    Field Description Reports The total number of reports (queries and unsolicited reports generated from joins or leaves) that have been received or sent. Leaves The number of Multicast leaves that have been sent. MLDv1 queries The number of MLDv1 queries that have been received. MLDv2 queries The number of MLDv2 queries that have been received. Malfo ...

  • Dell 9.8(0.0) - page 1041

    NOTE: The :: notation specifies successive hexadecimal fields of zero. interface interface Enter the keyword interface then the interface type and slot/port or number information: • For a port channel interface, enter the keywords port- channel then a number. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the s ...

  • Dell 9.8(0.0) - page 1042

    00:01:e8:17:5c:ae REACH Te 1/2 Vl 100 CP Dell# Dell#show ipv6 neighbors * - Active session role Ad Dn - Admin Down B - BGP C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients * 10.1.3.2 10.1.3.1 Te 1/3 Up 300 250 3 C Dell#show ipv6 neighbors detail Session Discriminator: 1 Neighbor Discri ...

  • Dell 9.8(0.0) - page 1043

    Parameters ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IPv6 routes correspon ...

  • Dell 9.8(0.0) - page 1044

    Version Description 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series TeraScale. Usage Information The following describes the show ipv6 route command shown in the following examples. Field Description (undefined) Identifies the type of route: • L = Local • C = conne ...

  • Dell 9.8(0.0) - page 1045

    type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, Gateway of last resort is not set Destination Dist/Metric, Gateway, Last Change ----------------------------------------------------- C 100::/64 [0/0] Direct, ...

  • Dell 9.8(0.0) - page 1046

    26 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on a switch. To configure and verify the iSCSI optimization feature, use the following Dell Networking OS commands. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements. Syntax ad ...

  • Dell 9.8(0.0) - page 1047

    To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. Defaults 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Net ...

  • Dell 9.8(0.0) - page 1048

    dscp dscp- value Enter the DSCP value assigned to the incoming packets in an iSCSI session. The valid range is from 0 to 63. The default is: the DSCP value in ingress packets is not changed. remark Marks the incoming iSCSI packets with the configured dot1p or DSCP value when they egress to the switch. The default is: the dot1and DSCP values in egre ...

  • Dell 9.8(0.0) - page 1049

    Version Description 9.6(0.0) Introduced on the Z9500. iscsi priority-bits Configure the priority bitmap that advertises in the iSCSI application TLVs. Syntax iscsi priority-bits To remove the configured priority bitmap, use the no iscsi priority-bits command. Defaults 4 (0x10 in the bitmap) Command Modes PROTOCOL LLDP (only on the global, not on th ...

  • Dell 9.8(0.0) - page 1050

    Version Description 9.6.(0.0) Introduced on the Z9500. iscsi target port Configure the iSCSI target ports and optionally, the IP addresses on which iSCSI communication is monitored. Syntax iscsi target port [ tcp-port-2...tcp-port-16 ]ip-address [ ip- address ] To remove the configured iSCSI target ports or IP addresses, use the no iscsi target por ...

  • Dell 9.8(0.0) - page 1051

    show iscsi Display the currently configured iSCSI settings. Syntax show iscsi Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version hist ...

  • Dell 9.8(0.0) - page 1052

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.6(0.0) Introduced on the Z9500. Example Dell# show isci session Session 0: - ...

  • Dell 9.8(0.0) - page 1053

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.6(0.0) Introduced on the Z9500. Ex ...

  • Dell 9.8(0.0) - page 1054

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.6(0.0) Introduced on the Z9500. Related Commands • show iscsi — displays the current ...

  • Dell 9.8(0.0) - page 1055

    27 Intermediate System to Intermediate System (IS-IS) The intermediate system to intermediate system (IS-IS) is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing both IP and OSI traffic. A router is considered an intermediate system. Networks ...

  • Dell 9.8(0.0) - page 1056

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is ...

  • Dell 9.8(0.0) - page 1057

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced Usage Information You cannot disable leaking from one level to another; however, you can reg ...

  • Dell 9.8(0.0) - page 1058

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 1059

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. Usage Information CAUTION: Use caution when you enter this command. Back up your configuration prior to using this command or your IS-IS configuration will be erased. clear isis Restart the IS-IS ...

  • Dell 9.8(0.0) - page 1060

    Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. clns host Define a name-to-network service mapping point (NSAP) that you use with commands that require NSAPs and system IDs. Z9500 Syntax clns host name nsap Parameters name Enter an alphanumeric string to identify the name-to-NSAP mapping. nsap Enter a specifi ...

  • Dell 9.8(0.0) - page 1061

    debug isis Enable debugging for all IS-IS operations. Z9500 Syntax debug isis To disable debugging of IS-IS, use the no debug isis command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following ...

  • Dell 9.8(0.0) - page 1062

    Parameters interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter th ...

  • Dell 9.8(0.0) - page 1063

    graceful-restart details tied to the VRF that you specify. This information includes GR Hello, Internal State, and Event Debug details. all Enter the keyword all to enable debugging information that includes all the logs that are related to graceful-restart. events Enter the keyword events to enable debugging information that includes logs that are ...

  • Dell 9.8(0.0) - page 1064

    • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. ...

  • Dell 9.8(0.0) - page 1065

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduce ...

  • Dell 9.8(0.0) - page 1066

    Version Description 6.3.1.0 Introduced. debug isis update-packets Enable debugging on link state PDUs (LSPs) that a router detects. Z9500 Syntax debug isis update-packets [ interface ] To turn off debugging, use the no debug isis update-packets [ interface ] command. Parameters interface (OPTIONAL) Identifies the interface type slot/port as one of ...

  • Dell 9.8(0.0) - page 1067

    default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information. Z9500 Syntax default-information originate [always] [metric metric ] [route- map map-name ] To disable the generation of a default route into the specified IS-IS routing domain, use the no default-information or ...

  • Dell 9.8(0.0) - page 1068

    router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one. How a metric value assigned to a default route advertises depends on the metric- style command configuration. If the metric-style command is set for Narrow mode and the metric value in the default-inform ...

  • Dell 9.8(0.0) - page 1069

    Version Description pre-7.7.1.0 Introduced. Related Commands router isis — Enter ROUTER mode on the switch. distance Define the administrative distance for learned routes. Z9500 Syntax distance weight [ ip-address mask [ prefix-list ]] To return to the default values, use the no distance weight command. Parameters weight The administrative distan ...

  • Dell 9.8(0.0) - page 1070

    Version Description 6.3.1.0 Introduced. Usage Information The administrative distance indicates the trust value of incoming packets. A low administrative distance indicates a high trust rate. A high value indicates a lower trust rate. For example, a weight of 255 is interpreted that the routing information source is not trustworthy and should be ig ...

  • Dell 9.8(0.0) - page 1071

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. Related Commands • distribute-list out — suppresses networks from being advertised in updates. • redistribute — redistributes routes ...

  • Dell 9.8(0.0) - page 1072

    Command Modes • ROUTER ISIS ( for IPv4 ) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 ( for IPv6 ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this c ...

  • Dell 9.8(0.0) - page 1073

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 1074

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 1075

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced on the E-Series. Usage Information Every graceful restart enabled router’s HELLO PDUs includes a restart TLV. This restart enables (re)star ...

  • Dell 9.8(0.0) - page 1076

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart restart-wait Enable the graceful restart maximum wait time before a restarting peer comes up. Z9500 Syntax ...

  • Dell 9.8(0.0) - page 1077

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. Related Commands graceful-restart t3 — configures the overall wait time before graceful restart completes. graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated. This wait time is the interval before the ...

  • Dell 9.8(0.0) - page 1078

    Version Description 8.3.1.0 Introduced on the E-Series. graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize. Z9500 Syntax graceful-restart t2 {level-1 | level-2} seconds To return to the default, use the no graceful-restart t2 command. Paramete ...

  • Dell 9.8(0.0) - page 1079

    graceful-restart t3 Configure the overall wait time before graceful restart completes. Z9500 Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command. Parameters adjacency Enter the keyword adjacency so that the restarting router receives the remaining time value from its peer and adju ...

  • Dell 9.8(0.0) - page 1080

    Related Commands graceful-restart restart-wait — enables the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Z9500 Syntax hello padding [multi-point | point-to-point ...

  • Dell 9.8(0.0) - page 1081

    hostname dynamic Enables dynamic learning of hostnames from routers in the domain and allows the routers to advertise the hostname in LSPs. Z9500 Syntax hostname dynamic To disable this command, use the no hostname dynamic command. Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information a ...

  • Dell 9.8(0.0) - page 1082

    Defaults In IS-IS, the default deletes LSPs with internal checksum errors ( no ignore-lsp- errors ). Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS versi ...

  • Dell 9.8(0.0) - page 1083

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced. Usage Information To assign a network entity title to en ...

  • Dell 9.8(0.0) - page 1084

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information Configure a network entity title (the net command) to specify the area address and the router system ID. T ...

  • Dell 9.8(0.0) - page 1085

    Defaults level-1-2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9 ...

  • Dell 9.8(0.0) - page 1086

    Defaults seconds = 10 ; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Descr ...

  • Dell 9.8(0.0) - page 1087

    Defaults seconds = 10 ; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Descr ...

  • Dell 9.8(0.0) - page 1088

    level-2 (OPTONAL) Select this value to configure the hello multiplier independently for Level 2 adjacencies. Defaults multiplier = 3 ; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refe ...

  • Dell 9.8(0.0) - page 1089

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Hello PDUs are “padded” only when both the global and interface padding options are ON. Turning either one OFF disables padding for the co ...

  • Dell 9.8(0.0) - page 1090

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information Dell Networking recomm ...

  • Dell 9.8(0.0) - page 1091

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 1092

    Version Description 8.3.11.1 Introduced on the Z9000. isis password Configure an authentication password for an interface. Z9500 Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [ password ] [level-1 | level-2] command. Parameters encryption- type (OPTIONAL) Enter 7 to encrypt the password ...

  • Dell 9.8(0.0) - page 1093

    Version Description 8.3.11.1 Introduced on the Z9000. Usage Information To protect your network from unauthorized access, use this command to prevent unauthorized routers from forming adjacencies. You can assign different passwords for different routing levels by using the keywords level-1 and level-2 . The no form of this command disables the pass ...

  • Dell 9.8(0.0) - page 1094

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information You can configure priorities independently for Level 1 and Level 2. Priorities determine which router on a LAN is the designated router. Prior ...

  • Dell 9.8(0.0) - page 1095

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information The IS-IS protocol automatically determines area boundaries and are able to keep Level 1 and Level 2 routing separate. Poorly planned use of t ...

  • Dell 9.8(0.0) - page 1096

    Usage Information This command allows you to monitor adjacency state changes, which are useful when you monitor large networks. Messages are logged in the system’s error message facility. lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs). Z9500 Syntax lsp-gen-interval [level-l | level-2] interva ...

  • Dell 9.8(0.0) - page 1097

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. Usage Information LSP throttling slows down the frequency at which LSPs are generated during network instability. Even though throttling LSP ...

  • Dell 9.8(0.0) - page 1098

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. Usage Information The link MTU and the LSP MTU size must be the same. Because each device can generate a m ...

  • Dell 9.8(0.0) - page 1099

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. Usage Information The refresh interval determines the rate at which route topology information is transmit ...

  • Dell 9.8(0.0) - page 1100

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. Usage Information To configure the number of area addresses on router, use this command. This value must b ...

  • Dell 9.8(0.0) - page 1101

    Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Change the maximum LSP lifetime with this command. The maximum LSP lifetime must always be greater than the LSP refresh interval. The seconds parameter enables the router to keep LSPs for the specified length of time. If the value is higher, th ...

  • Dell 9.8(0.0) - page 1102

    Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.0 Introduced. metric-style To generate and accept old-style, new-style, or both styles of type, length, and values (TLV), configure a router. Z9500 Syntax metric-style {narrow [transition] | transition | wide ...

  • Dell 9.8(0.0) - page 1103

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information If you enter the metric-style wide command, the Dell Networking OS generates and accepts only new-style TLVs. The router uses less memory and other resources rather than genera ...

  • Dell 9.8(0.0) - page 1104

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Introduced. net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start. Z9500 Syntax net network-entity-title ...

  • Dell 9.8(0.0) - page 1105

    passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. Z9500 Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: ...

  • Dell 9.8(0.0) - page 1106

    redistribute Redistribute routes from one routing domain to another routing domain. Z9500 Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value ] [metric-type {external | internal}] [route-map map-name ] To end redistribution or disable any of the specified keywords, use the no redistribute {static | co ...

  • Dell 9.8(0.0) - page 1107

    Command Modes • ROUTER ISIS ( for IPv4 ) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 ( for IPv6 ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this c ...

  • Dell 9.8(0.0) - page 1108

    redistribute bgp Redistribute routing information from a BGP process. Z9500 Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value ] [metric-type {external| internal}] [route-map map-name ] To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter ...

  • Dell 9.8(0.0) - page 1109

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 In ...

  • Dell 9.8(0.0) - page 1110

    Parameters process-id Enter a number that corresponds to the OSPF process ID to be redistributed. The range is from 1 to 65355. metric metric- value (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0 . metric-type {external | i ...

  • Dell 9.8(0.0) - page 1111

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. Usage Information How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command. If the metric-style ...

  • Dell 9.8(0.0) - page 1112

    Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Configure a network entity title (the net command) to specify the area address and ...

  • Dell 9.8(0.0) - page 1113

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.0 Introduced. Usage Information Set the overload bit when a router experiences problems, such as a memory s ...

  • Dell 9.8(0.0) - page 1114

    Example (Router-Isis) The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode. Dell(conf-router_isis)#show config ! router isis clns host ISIS 49.0000.0001.F100.E120.0013.00 log-adjacency-changes net 49.0000.0001.F100.E120.0013.00 ! address-family ipv6 unicast maximum-paths 16 multi-topology transition set-overload-bit s ...

  • Dell 9.8(0.0) - page 1115

    detail (OPTIONAL) Displays the detailed link-state database information of each LSP when specified. If not specified, a summary displays. summary (OPTIONAL) Displays the summary of link-state database information when specified. lspid (OPTIONAL) Display only the specified LSP. system-id (OPTIONAL) Displays the link-state database for system-id. Com ...

  • Dell 9.8(0.0) - page 1116

    Field Description The last octet is the LSP number. An LSP is divided into multiple LSP fragments if there is more data than cannot fit in a single LSP. Each fragment has a unique LSP number. An * after the LSPID indicates that the system originates an LSP where this command was issued. LSP Seq Num This value is the sequence number for the LSP that ...

  • Dell 9.8(0.0) - page 1117

    Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 10 IPv6 (MT-IPv6) 1511::/64 Metric: 10 IPv6 (MT-IPv6) 2511::/64 Metric: 10 IPv6 (MT-IPv6) 1011::/64 Metric: 10 IPv6 1511::/64 Metric: 10 IP 10.1.1.0 255.255.255.0 Hostname: ISIS IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00- ...

  • Dell 9.8(0.0) - page 1118

    NOTE: If you do not specify this option, the IS-IS graceful restart details corresponding to the default VRF are displayed. Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version ...

  • Dell 9.8(0.0) - page 1119

    show isis hostname Display IS-IS host names configured or learned on the switch. Z9500 Syntax show isis [vrf vrf-name ] hostname Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IS-IS host names corresponding to that VRF. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specifi ...

  • Dell 9.8(0.0) - page 1120

    Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS interface status information corresponding to that VRF. interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port info ...

  • Dell 9.8(0.0) - page 1121

    TenGigabitEthernet 1/8 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 38371358, Local circuit ID 2 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.02 Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10 Number of active level-1 adjacencies: 1 Level-2 Metric: 10, P ...

  • Dell 9.8(0.0) - page 1122

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduce ...

  • Dell 9.8(0.0) - page 1123

    IP Address(es): 25.1.1.3* MAC Address: 0000.0000.0000 Hold Time: 28 Link Local Address: fe80::201:e8ff:fe00:492c Topology: IPv4 IPv6 , Common (IPv4 IPv6 ) Adjacency being used for MTs: IPv4 IPv6 Dell# show isis protocol Display IS-IS routing information. Z9500 Syntax show isis [vrf vrf-name ] protocol Parameters vrf vrf-name (OPTIONAL) Enter the ke ...

  • Dell 9.8(0.0) - page 1124

    Interfaces supported by IS-IS: TenGigabitEthernet 1/1 - IP - IPv6 TenGigabitEthernet 1/2 - IP - IPv6 TenGigabitEthernet 1/10 - IP - IPv6 Loopback 0 - IP - IPv6 Redistributing: Distance: 115 Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in t ...

  • Dell 9.8(0.0) - page 1125

    Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information The following describes the show isis traffic command shown in the following examp ...

  • Dell 9.8(0.0) - page 1126

    IS-IS: Level-1 LSPs flooded (sent/rcvd) : 0/0 IS-IS: Level-2 LSPs flooded (sent/rcvd) : 5934/5217 IS-IS: Level-1 LSPs CSNPs (sent/rcvd) : 0/0 IS-IS: Level-2 LSPs CSNPs (sent/rcvd) : 472/238 IS-IS: Level-1 LSPs PSNPs (sent/rcvd) : 0/0 IS-IS: Level-2 LSPs PSNPs (sent/rcvd) : 10/337 IS-IS: Level-1 DR Elections : 4 IS-IS: Level-2 DR Elections : 4 IS-IS ...

  • Dell 9.8(0.0) - page 1127

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for multi-topolog ...

  • Dell 9.8(0.0) - page 1128

    28 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. NOTE: For static LAG commands, refer to Port Channel Commands ...

  • Dell 9.8(0.0) - page 1129

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Z9500 Syntax debug lacp [config | ...

  • Dell 9.8(0.0) - page 1130

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1131

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command applies to dynamic port-channel interfaces only. When applied on a static port-channel, t ...

  • Dell 9.8(0.0) - page 1132

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp system-priority Configure the LACP system priority. Z9500 Syntax lacp system-priority priority-value Parameters priority-value Enter the port-priority ...

  • Dell 9.8(0.0) - page 1133

    port-channel mode Configure the LACP port channel mode. Z9500 Syntax port-channel number mode [active] [passive] [off] Parameters number Enter the keywords number then a number. active Enter the keyword active to set the mode to the active state. NOTE: LACP modes are defined in Usage Information . passive Enter the keyword passive to set the mode t ...

  • Dell 9.8(0.0) - page 1134

    Mode Function automatically initiates negotiation with other ports by initiating LACP packets. passive An interface is not in an active negotiating state in this mode. LACP runs on any link configured in the passive state. Ports in a passive state respond to negotiation requests from other ports that are in active states. Ports in a passive state r ...

  • Dell 9.8(0.0) - page 1135

    show lacp Display the LACP matrix. Z9500 Syntax show lacp port-channel-number [sys-id | counters] Parameters port-channel- number Enter a port-channel number. The range is from 1 to 128. sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters. De ...

  • Dell 9.8(0.0) - page 1136

    enabled L-Distribution disabled, M-Partner Defaulted, N-Partner Non-defaulted, O-Receiver is in expired state, P-Receiver is not in expired state Port Te 1/6 is enabled, LACP is enabled and mode is lacp Actor Admin: State ACEHJLMP Key 1 Priority 128 Oper: State ACEGIKNP Key 1 Priority 128 Partner Admin: State BDFHJLMP Key 0 Priority 0 Oper: State B ...

  • Dell 9.8(0.0) - page 1137

    29 Layer 2 This chapter describes commands to configure Layer 2 features. This chapter contains the following sections: • MAC Addressing Commands • Virtual LAN (VLAN) Commands • Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-tab ...

  • Dell 9.8(0.0) - page 1138

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. vlan vlan-id Enter the keyword vlan then a VLAN ID number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command L ...

  • Dell 9.8(0.0) - page 1139

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1140

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords port- channel then a number. The range is from 1 to 512. output-range interface For a multicast MAC address, enter the keyword output- range then one of the following interfaces to indicate a rang ...

  • Dell 9.8(0.0) - page 1141

    Example (Multicast) mac-address-table static 01:00:5E:01:00:01 {multicast vlan 2 output—range Te 1/2,Te 1/3 } Related Commands show mac-address-table — displays the MAC address table. mac-address-table station-move refresh-arp Ensure that address resolution protocol (ARP) refreshes the egress interface when a station move occurs due to a topolo ...

  • Dell 9.8(0.0) - page 1142

    vlan vlan-id E-Series only: Enter the keyword then the VLAN ID. The range is from 1 to 4094. dynamic (OPTIONAL) Enter the keyword dynamic to allow aging of MACs even though a learning limit is configured. station-move- violation (OPTIONAL) Enter the keywords station-move to allow a station move on learned MAC addresses. Defaults • On S-Series, th ...

  • Dell 9.8(0.0) - page 1143

    another interface. Enabling or disabling this option has no effect on already learned MAC addresses. After the MAC address learning limit is reached, the MAC addresses do not age out unless you add the dynamic option. To clear statistics on MAC address learning, use the clear counters command with the learning-limit parameter. NOTE: If you configur ...

  • Dell 9.8(0.0) - page 1144

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1145

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information If you configure mac-learn-limit and the sticky MAC feature is enabled, dynamically learned MAC addresses are converted to sticky for that port. Any new MAC address that is learned also becomes sticky for that ...

  • Dell 9.8(0.0) - page 1146

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands show mac learning-limit — displays detai ...

  • Dell 9.8(0.0) - page 1147

    show cam mac linecard (dynamic or static) Display the CAM size and the portions allocated for MAC addresses and for MAC ACLs. Z9500 Syntax show cam mac linecard slot-id port-set port-pipe [address mac_addr | dynamic | interface interface | static | vlan vlan- id ] Parameters linecard slot-id (REQUIRED) Enter the keyword linecard then a slot number ...

  • Dell 9.8(0.0) - page 1148

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Example Dell# show cam mac linecard 1 port-set 0 PVlanId Mac Address Region Interface 1 00:01:0 ...

  • Dell 9.8(0.0) - page 1149

    interface interface (OPTIONAL) Enter the keyword interface then the interface type, slot and port information: • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabi ...

  • Dell 9.8(0.0) - page 1150

    Column Heading Description VlanId Displays the VLAN ID number. Mac Address Displays the MAC address in nn:nn:nn:nn:nn:nn format. Type Lists whether the MAC address was manually configured (Static), learned dynamically (Dynamic), or associated with a specific port (Sticky). Interface Displays the interface type and slot/port information. The followi ...

  • Dell 9.8(0.0) - page 1151

    Column Heading Description State Lists if the MAC address is in use (Active) or not in use (Inactive). The following describes the show mac-address-table count command shown in the following example. Line Beginning With Description MAC Entries... Displays the number of MAC entries learned per VLAN. Dynamic Address... Lists the number of dynamically ...

  • Dell 9.8(0.0) - page 1152

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series and S-Series. 6.2.1.1 Introduced on the E-Series. Example Dell#show mac-address-table aging-time Mac-address-tab ...

  • Dell 9.8(0.0) - page 1153

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1154

    default vlan-id Specify a VLAN as the Default VLAN. Z9500 Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1 . Defaults ...

  • Dell 9.8(0.0) - page 1155

    default-vlan disable Disable the default VLAN so that all switchports are placed in the Null VLAN until they are explicitly configured as a member of another VLAN. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Com ...

  • Dell 9.8(0.0) - page 1156

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1157

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Example Dell(conf-if-vl-100)#show config ! interface Vlan 100 no ip address no shutdown Dell(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch. Z9500 Syntax show vlan [brief | id vlan-id | name vlan-name ] Parameters brief (OPT ...

  • Dell 9.8(0.0) - page 1158

    Version Description 9.1.(0.0) Updated to support OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Augmented to display PVLAN data for the C-Series and S- Series and revised the output to include the Description field to display a user-entered VLAN description. 7.6.1.0 Introduced ...

  • Dell 9.8(0.0) - page 1159

    Column Heading Description Ports Displays the type, slot, and port information. • Po = port channel • Te = 10-Gigabit Ethernet • Fo = 40-Gigabit Ethernet Example Dell#show vlan Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow Q: U - Untagged, T - Tagged x - Dot1x u ...

  • Dell 9.8(0.0) - page 1160

    10 0 1800 unassigned 20 0 1800 2.3.3.3/24 30 0 1800 2.1.1.1/24 Example (Name) Dellconf)#interface vlan 20 Dell(conf-if-vl-20)#name test Dell(conf-if-vl-20)#do show vlan name test Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow Q: U - Untagged, T - Tagged x - Dot1x untag ...

  • Dell 9.8(0.0) - page 1161

    Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 1162

    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults Not configured. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other ...

  • Dell 9.8(0.0) - page 1163

    untagged Add a Layer 2 interface to a VLAN as an untagged interface. Z9500 Syntax untagged interface To remove an untagged interface from a VLAN, use the no untagged interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a port channel interface, enter the keywords port- channel then a numb ...

  • Dell 9.8(0.0) - page 1164

    Usage Information Untagged interfaces can only belong to one VLAN. In the Default VLAN, you cannot use the no untagged interface command. To remove an untagged interface from all VLANs, including the Default VLAN, enter INTERFACE mode and use the no switchport command. Related Commands interface vlan — configures a VLAN. tagged — specifies whic ...

  • Dell 9.8(0.0) - page 1165

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 1166

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 1167

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information When you enter no fefd for an interface and fefd-global, FEFD is enabled on the interface because the no fefd command is not retained in the configuration file. To keep the interface FEFD disabled when the global configuration changes, use the f ...

  • Dell 9.8(0.0) - page 1168

    fefd mode Change the FEFD mode on an interface. Z9500 Syntax fefd mode {normal | aggressive}] To return the FEFD mode to the default of normal, use the no fefd mode command. Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interfac ...

  • Dell 9.8(0.0) - page 1169

    fefd reset Reset all interfaces or a single interface that was in “error-disabled” mode. Z9500 Syntax fefd reset [ interface ] Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 4 ...

  • Dell 9.8(0.0) - page 1170

    Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds . Defaults 15 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Gu ...

  • Dell 9.8(0.0) - page 1171

    interface is placed in “error-disabled” state, t enter the fefd reset command to reset the interface state. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list ...

  • Dell 9.8(0.0) - page 1172

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1173

    Te 1/5 Aggressive 10 Admin Shutdown Te 1/6 Aggressive 10 Admin Shutdown Te 1/7 Aggressive 10 Admin Shutdown Te 1/8 Aggressive 10 Admin Shutdown Te 1/9 Aggressive 10 Admin Shutdown Te 1/10 NA NA Locally disabled Te 1/11 Aggressive 10 Err-disabled Dell# Related Commands • fefd — enables far-end failure detection. • fefd disable — disables FEF ...

  • Dell 9.8(0.0) - page 1174

    30 Link Layer Discovery Protocol (LLDP) Link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. This chapter contains the following sections: • LLPD Commands • LLDP-MED Commands LLDP facilitates multi-vendor interoperability by using standard management tool ...

  • Dell 9.8(0.0) - page 1175

    port-vlan-id Enter the keywords port-vlan-id to advertise the port VLAN identification TLV. vlan-name Enter the keywords vlan-name to advertise the vlan-name TLV. This keyword is only supported on the C-Series and S- Series. Defaults Disabled. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if- interface -lldp) Command History This guid ...

  • Dell 9.8(0.0) - page 1176

    Parameters max-frame- size Enter the keywords max-frame-size to advertise the dot3 maximum frame size. Defaults none Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if- interface -lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Re ...

  • Dell 9.8(0.0) - page 1177

    Defaults none Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on t ...

  • Dell 9.8(0.0) - page 1178

    Defaults none Command Modes INTERFACE (conf- interface -lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introdu ...

  • Dell 9.8(0.0) - page 1179

    Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Z9500 Syntax clear lldp neighbo ...

  • Dell 9.8(0.0) - page 1180

    Version Description 7.4.1.0 Introduced on the E-Series. debug lldp interface To display timer events, neighbor additions or deletions, and other information about incoming and outgoing packets, enable LLDP debugging. Z9500 Syntax debug lldp interface { interface | all}{events | packet {brief | detail} {tx | rx | both}} To disable debugging, use the ...

  • Dell 9.8(0.0) - page 1181

    Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8 ...

  • Dell 9.8(0.0) - page 1182

    Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Related Commands protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. show running-config lldp — displays the LLDP running co ...

  • Dell 9.8(0.0) - page 1183

    Version Description 7.4.1.0 Introduced on the E-Series. management-interface Enable and configure LLDP protocol parameters on the management interface. Z9500 Syntax management-interface To remove LLDP configuration on a management interface, use the no management-interface command. Command Modes LLDP (conf-lldp) Command History This guide is platfo ...

  • Dell 9.8(0.0) - page 1184

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1185

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch. Z9500 Syntax protocol lldp To disable LLDP globally on the chassis, use the no protoc ...

  • Dell 9.8(0.0) - page 1186

    To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if- interface -lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line ...

  • Dell 9.8(0.0) - page 1187

    detail (OPTIONAL) Enter the keyword detail to display all the TLV information, remote management IP addresses, timers, and LLDP tx and rx counters. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference ...

  • Dell 9.8(0.0) - page 1188

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introd ...

  • Dell 9.8(0.0) - page 1189

    show running-config lldp Display the current global LLDP configuration. Z9500 Syntax show running-config lldp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of th ...

  • Dell 9.8(0.0) - page 1190

    The E-Series generally supports the commands. However, LLDP-MED commands are more useful on the C-Series and the S50V model of the S-Series, because they support Power over Ethernet (PoE) devices. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devi ...

  • Dell 9.8(0.0) - page 1191

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLD ...

  • Dell 9.8(0.0) - page 1192

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1193

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Usage Information • ECS — Emergency call service such as defined by TIA or the national emergency numberi ...

  • Dell 9.8(0.0) - page 1194

    Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. show running-c ...

  • Dell 9.8(0.0) - page 1195

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. show running-config lldp — displa ...

  • Dell 9.8(0.0) - page 1196

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1197

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1198

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1199

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1200

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. s ...

  • Dell 9.8(0.0) - page 1201

    31 Microsoft Network Load Balancing Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover a ...

  • Dell 9.8(0.0) - page 1202

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Added support for the association of an IP address with a multicast MA ...

  • Dell 9.8(0.0) - page 1203

    information inside the ARP packet. This unicast data traffic flooding occurs only for those packets which use these ARP entries. mac-address-table static (for Multicast MAC Address) To configure the multicast mode of network load balancing (NLB) on the switch, you must associate a multicast MAC address with the VLAN used to switch Layer 2 multicast ...

  • Dell 9.8(0.0) - page 1204

    Version Description 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Added support for multicast MAC address on the MXL platform. Usage Information When a multicast source and multicast receivers are in the same VLAN, you can configure a router so that multicast traffic is switched only to the ports assigned to a VLAN that is associated with a static mul ...

  • Dell 9.8(0.0) - page 1205

    32 Multicast The multicast commands are supported by Dell Networking operating system. This chapter contains the following sections: • IPv4 Multicast Commands • IPv6 Multicast Commands IPv4 Multicast Commands This section describes the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To ...

  • Dell 9.8(0.0) - page 1206

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduce ...

  • Dell 9.8(0.0) - page 1207

    mask Enter the mask in slash prefix formation ( /x ) or in dotted decimal format. null 0 (OPTIONAL) Enter the keyword null then zero (0). [ protocol [ process-id | tag ] ip-address ] (OPTIONAL) Enter one of the routing protocols: • Enter the BGP as-number then the IP address in dotted decimal format of the reverse path forwarding (RPF) neighbor. ...

  • Dell 9.8(0.0) - page 1208

    ip multicast-limit To limit the number of multicast entries on the system, use this feature. Z9500 Syntax ip multicast-limit [vrf vrf-name ] limit Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to limit the number of multicast on the VRF. limit Enter the desired maximum number of multicast entries on the sy ...

  • Dell 9.8(0.0) - page 1209

    ip multicast-routing Enable IP multicast forwarding. Z9500 Syntax ip multicast-routing [vrf vrf-name ] To disable multicast forwarding, use the no ip multicast-routing [vrf vrf-name ] command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the r ...

  • Dell 9.8(0.0) - page 1210

    Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. static (OPTIONAL) Enter the keyword static to view static multicast routes. group-address [ source- address ] (OPTIONAL) Enter the multicast ...

  • Dell 9.8(0.0) - page 1211

    Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id , group-address , and source-address parameters were added ...

  • Dell 9.8(0.0) - page 1212

    Vlan 30 (50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time ...

  • Dell 9.8(0.0) - page 1213

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1214

    Parameters int-count Enter the keyword count to indicate the number of required debug messages. interface type Enter the following keywords and slot/port information: • For a 10G Ethernet interface, enter the keyword tengigabitethernet then the slot/port information. • For a 40G interface, enter the keyword fortyGigE then the slot/port informat ...

  • Dell 9.8(0.0) - page 1215

    limit Enter the desired maximum number of multicast entries on the system. The S-Series range is from 1 to 16000. Defaults The S-Series default is 4000 . Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . ...

  • Dell 9.8(0.0) - page 1216

    33 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP conn ...

  • Dell 9.8(0.0) - page 1217

    clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Z9500 Syntax clear ip msdp sa-cache [ group-address | rejected-sa | local] Parameters group-address Enter the group IP address in dotted decimal format (A.B.C.D.). rejected-sa Enter the k ...

  • Dell 9.8(0.0) - page 1218

    clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Z9500 Syntax clear ip msdp sa-cache [ group-address | rejected-sa | local] Parameters group-address Enter the group IP address in dotted decimal format (A.B.C.D.). rejected-sa Enter the ...

  • Dell 9.8(0.0) - page 1219

    debug ip msdp Turn on MSDP debugging. Z9500 Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer add ...

  • Dell 9.8(0.0) - page 1220

    To clear the MSDP rejected source-active entries, use the no ip msdp cache- rejected-sa { number } command then the ip msdp cache-rejected-sa { number } command. Parameters number Enter the number of rejected SA entries to cache. The range is from 0 to 32766. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. ...

  • Dell 9.8(0.0) - page 1221

    Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on th ...

  • Dell 9.8(0.0) - page 1222

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip msdp mesh-group To be a member of a mesh group, configure a peer. Z9500 Syntax ip msdp mesh-group { name } { peer address } To remove the peer from a mesh group, use the no ip msdp mesh-group { name } { pee ...

  • Dell 9.8(0.0) - page 1223

    group, member X accepts the SA message and forwards it to all of its peers that are not part of the mesh-group. However, member X cannot forward the SA message to other members of the mesh-group. ip msdp originator-id Configure the MSDP Originator ID. Z9500 Syntax ip msdp originator-id { interface } To remove the originator-id, use the no ip msdp o ...

  • Dell 9.8(0.0) - page 1224

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 6.2.1.1 Introduced ip msdp peer Configure an MSDP peer. Z9500 Syntax ip msdp peer peer address [connect-source] [description] [sa- limit number ] To remove the MSDP peer, use the no ip msdp peer peer ad ...

  • Dell 9.8(0.0) - page 1225

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Intr ...

  • Dell 9.8(0.0) - page 1226

    ip msdp redistribute Filter local PIM SA entries in the SA cache. SAs which the ACL denies time out and are not refreshed. Until they time out, they continue to reside in the MSDP SA cache. Z9500 Syntax ip msdp redistribute [list acl-name ] Parameters list acl-name lEnter the name of an extended ACL that contains permitted SAs. If you do not use th ...

  • Dell 9.8(0.0) - page 1227

    ip msdp sa-filter Permit or deny MSDP source active (SA) messages based on multicast source and/or group from the specified peer. Z9500 Syntax ip msdp sa-filter {in | out} peer-address list [access- list name ] Remove this configuration using the no ip msdp sa-filter {in | out} peer address list [access- list name ] command. Parameters in Enter the ...

  • Dell 9.8(0.0) - page 1228

    ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Z9500 Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache. The range is from 0 to 40000. Defaults 50000 Command Modes CONFIGURATION Command Histor ...

  • Dell 9.8(0.0) - page 1229

    ip msdp shutdown Administratively shut down a configured MSDP peer. Z9500 Syntax ip msdp shutdown { peer address } Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, ...

  • Dell 9.8(0.0) - page 1230

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1231

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced Example Dell#show ip msdp peer 100.1.1.1 Peer Addr: 100.1.1.1 Local Addr: 100.1.1.2(639) Connect Source: none State: Established Up/Down Time: 00:00:08 Timers: KeepAlive 60 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learn ...

  • Dell 9.8(0.0) - page 1232

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 7.4.1.0 Introduced. Example Dell#show ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 200 rejected SAs rec ...

  • Dell 9.8(0.0) - page 1233

    34 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol and view information on the protocol. Z9500 Syntax debug spanning-tree mstp [all | bpdu interface {in | ou ...

  • Dell 9.8(0.0) - page 1234

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Int ...

  • Dell 9.8(0.0) - page 1235

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Related Commands protocol spanning-tree mstp — enters MULTIPLE SPANNING TREE mode. forward-delay The ...

  • Dell 9.8(0.0) - page 1236

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Related Commands max-age — changes the wait time before MSTP refreshes protocol configuration information. hello-time — changes the time interval between bridge protoc ...

  • Dell 9.8(0.0) - page 1237

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Related Commands forward-delay — the amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. max-age — changes the wait time before MSTP refreshes protocol configur ...

  • Dell 9.8(0.0) - page 1238

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Related Commands forward-delay — the amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. hello-time — changes the time interval between BPDUs. max-hops Configur ...

  • Dell 9.8(0.0) - page 1239

    Version Description 6.5.1.0 Introduced. Usage Information The max-hops command is a configuration command that applies to both the IST and all MST instances in the MSTP region. The BPDUs sent out by the root switch set the remaining-hops parameter to the configured value of max-hops. When a switch receives the BPDU, it decrements the received value ...

  • Dell 9.8(0.0) - page 1240

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Usage Information By default, all VLANs are mapped to MST instance zero (0) unless you use the vlan ra ...

  • Dell 9.8(0.0) - page 1241

    Version Description 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Usage Information For two MSTP switches to be within the same MSTP region, the switches must share the same region name (including matching case). Related Commands msti — maps the VLAN(s) to an MST instance. revision — assigns the revision number to the MST configuratio ...

  • Dell 9.8(0.0) - page 1242

    Usage Information MSTP is not enabled when you enter MULTIPLE SPANNING TREE mode. To enable MSTP globally on the switch, enter the no disable command while in MULTIPLE SPANNING TREE mode. For more information about the multiple spanning tree protocol, refer to the Dell Networking OS Configuration Guide . Example Dell(conf)#protocol spanning-tree ms ...

  • Dell 9.8(0.0) - page 1243

    Version Description 6.2.1.1 Introduced on the E-Series. Usage Information For two MSTP switches to be within the same MST region, the switches must share the same revision number. Related Commands msti — maps the VLAN(s) to an MST instance. name — assigns the region name to the MST region. show config View the current configuration for the mode ...

  • Dell 9.8(0.0) - page 1244

    max-hops 5 Dell(conf-mstp)# show spanning-tree mst configuration View the multiple spanning tree configuration. Z9500 Syntax show spanning-tree mst configuration Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command L ...

  • Dell 9.8(0.0) - page 1245

    show spanning-tree msti View the multiple spanning tree instance. Z9500 Syntax show spanning-tree msti [ instance-number [brief]] [guard] Parameters instance- number (Optional) Enter the multiple spanning tree instance number. The range is from 0 to 63. brief (Optional) Enter the keyword brief to view a synopsis of the MST instance. guard (Optional ...

  • Dell 9.8(0.0) - page 1246

    hops 5 Current root has priority 16384, Address 0001.e800.0a5c Number of topology changes 0, last change occurred 3058087 Port 82 (TenGigabitEthernet 2/0) is designated Forwarding Port path cost 0, Port priority 128, Port Identifier 128.82 Designated root has priority 16384, address 0001.e800.0a:5c Designated bridge has priority 32768, address 0001 ...

  • Dell 9.8(0.0) - page 1247

    Bridge Identifier has priority 32768, Address 0001.e801.6aa8 Configured hello time 2, max age 20, forward delay 15, max hops 20 We are the root of MSTI 0 (CIST) Current root has priority 32768, Address 0001.e801.6aa8 CIST regional root ID Priority 32768, Address 0001.e801.6aa8 CIST external path cost 0 Number of topology changes 1, last change occu ...

  • Dell 9.8(0.0) - page 1248

    Parameters spanning-tree Enter the keywords spanning-tree to enable the MSTP on the interface. Defaults Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking ...

  • Dell 9.8(0.0) - page 1249

    Defaults • cost = depends on the interface type • priority = 128 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Versi ...

  • Dell 9.8(0.0) - page 1250

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 1251

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced Usage Information By default, the system implements an optimized flush mechanism for MSTP. This mechani ...

  • Dell 9.8(0.0) - page 1252

    35 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First (OSPF) is an Interior Gateway Protocol (IGP), which means that it distributes routing information between routers in a single Autonomous System (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to ...

  • Dell 9.8(0.0) - page 1253

    cost Specifies the stub area’s advertised external route metric. The range is from zero (0) to 65535. Defaults cost = 1 ; no areas are configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The fol ...

  • Dell 9.8(0.0) - page 1254

    default- information- originate (OPTIONAL) Allows external routing information to be imported into the NSSA by using Type 7 default. no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other ...

  • Dell 9.8(0.0) - page 1255

    suppressed and the component networks remain hidden from other areas.) Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version hi ...

  • Dell 9.8(0.0) - page 1256

    Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. ...

  • Dell 9.8(0.0) - page 1257

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1258

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Z9500 Syntax clear ip ospf process-id statistics [interface name {neighbor router-id }] Parameters process-id Enter the OSPF Process ID to c ...

  • Dell 9.8(0.0) - page 1259

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Related Commands show ip ospf statistics — displays the OSPF statistics. debug ip ospf Display debug information on OSPF. Entering the de ...

  • Dell 9.8(0.0) - page 1260

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the database-timer rate-limit option for the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1. ...

  • Dell 9.8(0.0) - page 1261

    Field Description auk: If the ip ospf authentication-key command is configured, this field displays the key used. keyid: If the ip ospf message-digest-key command is configured, this field displays the MD5 key to: Displays the interface to which the packet is intended. dst: Displays the destination IP address. netmask: Displays the destination IP a ...

  • Dell 9.8(0.0) - page 1262

    default-information originate To generate a default external route into an OSPF routing domain, configure the system. Z9500 Syntax default-information originate [always] [metric metric-value ] [metric-type type-value ] [route-map map-name ] To return to the default values, use the no default-information originate command. Parameters always (OPTIONA ...

  • Dell 9.8(0.0) - page 1263

    Version Description 6.1.1.1 Introduced on the E-Series. Related Commands redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command. Z9500 Syntax default-metric number To return to the default values ...

  • Dell 9.8(0.0) - page 1264

    description Add a description about the selected OSPF configuration. Z9500 Syntax description description To remove the OSPF description, use the no description command. Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults none Command Modes ROUTER OSPF Command History This guid ...

  • Dell 9.8(0.0) - page 1265

    Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110 . ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n format. access-list- name (OPTIONAL) Enter the na ...

  • Dell 9.8(0.0) - page 1266

    inter-area dist2 (OPTIONAL) Enter the keywords inter-area then a number to specify a distance metric for routes between areas. The range is from 1 to 255. The default is 110 . intra-area dist1 (OPTIONAL) Enter the keywords intra-area then a number to specify a distance metric for all routes within an area. The range is from 1 to 255. The default is ...

  • Dell 9.8(0.0) - page 1267

    Parameters prefix-list- name Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For Port Channel groups, enter the keywords port- channel then a number. For Z9500, the range is from 1 to 512. • For a SONET interface, enter the keyword sonet then the slot/p ...

  • Dell 9.8(0.0) - page 1268

    distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. Z9500 Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters prefi ...

  • Dell 9.8(0.0) - page 1269

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information The distribute-lis ...

  • Dell 9.8(0.0) - page 1270

    fast-convergence This command sets the minimum LSA origination and arrival times to zero (0), allowing more rapid route computation so that convergence takes less time. Z9500 Syntax fast-convergence { number } To cancel fast-convergence, use the no fast convergence command. Parameters number Enter the convergence level desired. The higher this para ...

  • Dell 9.8(0.0) - page 1271

    flood-2328 Enable RFC-2328 flooding behavior. Z9500 Syntax flood-2328 To disable, use the no flood-2328 command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list ...

  • Dell 9.8(0.0) - page 1272

    graceful-restart grace-period Specifies the time duration, in seconds, that the router’s neighbors continue to advertise the router as fully adjacent regardless of the synchronization state during a graceful restart. Z9500 Syntax graceful-restart grace-period seconds To disable the grace period, use the no graceful-restart grace-period command. P ...

  • Dell 9.8(0.0) - page 1273

    Parameters ip-address Enter the OSPF router-id, in IP address format, of the restart router that will not act as a helper during graceful restart. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Re ...

  • Dell 9.8(0.0) - page 1274

    Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduce ...

  • Dell 9.8(0.0) - page 1275

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. Added Restart and Helper roles support on the S-Series. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. ip ...

  • Dell 9.8(0.0) - page 1276

    Version Description 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface. Z9500 Syntax ip ospf authentication-key [ encryption-type ] key To delete an authentication key, use the no ip ospf authentication-key command. Parameters encryption- type (OPTIONAL) ...

  • Dell 9.8(0.0) - page 1277

    ip ospf cost Change the cost associated with the OSPF traffic on an interface. Z9500 Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters cost Enter a number as the cost. The range is from 1 to 65535. Defaults The default cost is based on the reference bandwidth. Command Modes INTERFACE Command History Th ...

  • Dell 9.8(0.0) - page 1278

    ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. Z9500 Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters seconds Enter the number of seconds for the ...

  • Dell 9.8(0.0) - page 1279

    To return to the default value, use the no ip ospf hello-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds . Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the ...

  • Dell 9.8(0.0) - page 1280

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 1281

    Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1282

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. ip ospf priority To determine the design ...

  • Dell 9.8(0.0) - page 1283

    Usage Information Setting a priority of 0 makes the router ineligible for election as a designated router or backup designated router. Use this command for interfaces connected to multi-access networks, not point- to-point networks. ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies ...

  • Dell 9.8(0.0) - page 1284

    Usage Information Set the time interval to a number large enough to prevent unnecessary retransmissions. For example, the interval must be larger for interfaces connected to virtual links. ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed. Z9500 Syntax ip ospf transmit-delay seconds To return ...

  • Dell 9.8(0.0) - page 1285

    log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set the system. Z9500 Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platf ...

  • Dell 9.8(0.0) - page 1286

    Defaults 4 Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1 ...

  • Dell 9.8(0.0) - page 1287

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced to all platforms. Usage Information This command is either enabled or disabled. If no OSPF process is identified as the MIB manager, the first OSPF process is used. If an OSPF process has been selected, it must be disabled prior to assigning ne ...

  • Dell 9.8(0.0) - page 1288

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced to all platforms. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To enable OSPF on an interface, the network area command must include, in its range of addresses, th ...

  • Dell 9.8(0.0) - page 1289

    Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduce ...

  • Dell 9.8(0.0) - page 1290

    • All previous no passive-interface interface commands are removed from the running configuration. no passive-interface interface • Remove the interface from the passive list. • The ABR status for the router is updated. • If passive-interface default is specified, then save no passive- interface interface into the running configuration. No ...

  • Dell 9.8(0.0) - page 1291

    Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the ...

  • Dell 9.8(0.0) - page 1292

    • 1 = for OSPF External type 1 • 2 = for OSPF External type 2 route-map map-name (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Defaults none Command Modes ROUTER OSPF Command History This ...

  • Dell 9.8(0.0) - page 1293

    Parameters tag (OPTIONAL) Enter the name of the IS-IS routing process. level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 rout ...

  • Dell 9.8(0.0) - page 1294

    router-id To configure a fixed router ID, use this command. Z9500 Syntax router-id ip-address To remove the fixed router ID, use the no router-id ip-address command. Parameters ip-address Enter the router ID in the IP address format. Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information ab ...

  • Dell 9.8(0.0) - page 1295

    n]: Dell# router ospf To configure an OSPF instance, enter ROUTER OSPF mode. Z9500 Syntax router ospf process-id [vrf { vrf name }] To clear an OSPF instance, use the no router ospf process-id command. Parameters process-id Enter a number for the OSPF instance. The range is from 1 to 65535. vrf name (Optional) E-Series Only: Enter the VRF process i ...

  • Dell 9.8(0.0) - page 1296

    After the OSPF process and the VRF are tied together, you cannot use the OSPF Process ID again in the system. Example Dell(conf)#router ospf 2 Dell(conf-router_ospf)# show config Display the non-default values in the current OSPF configuration. Z9500 Syntax show config Command Modes ROUTER OSPF Command History This guide is platform-specific. For c ...

  • Dell 9.8(0.0) - page 1297

    Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refer ...

  • Dell 9.8(0.0) - page 1298

    Line Beginning with Description “Min LSA....” Displays the intervals set for LSA transmission and acceptance. “Number of...” Displays the number and type of areas configured for this process ID. Example Dell#show ip ospf 10 Routing Process ospf 10 with ID 1.1.1.1 Virtual router default- vrf Supports only single TOS (TOS0) routes SPF schedul ...

  • Dell 9.8(0.0) - page 1299

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-S ...

  • Dell 9.8(0.0) - page 1300

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1301

    Type-5 AS External Link ID ADV Router Age Seq# Checksum Tag 0.0.0.0 192.68.135.2 908 0x80000052 0xeb83 100 1.1.1.1 192.68.135.2 908 0x8000002a 0xbd27 0 10.1.1.0 11.1.2.1 718 0x80000002 0x9012 0 10.1.2.0 11.1.2.1 718 0x80000002 0x851c 0 10.2.2.0 11.1.2.1 718 0x80000002 0x7927 0 10.2.3.0 11.1.2.1 718 0x80000002 0x6e31 0 10.2.4.0 13.1.1.1 1184 0x80000 ...

  • Dell 9.8(0.0) - page 1302

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C- ...

  • Dell 9.8(0.0) - page 1303

    Summary Asbr (Area 0.0.0.0) LS age: 1437 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000000f Checksum: 0x8221 Length: 28 Network Mask: /0 TOS: 0 Metric: 2 LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.1 Advert ...

  • Dell 9.8(0.0) - page 1304

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1305

    Field Description TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router. External Route Tag Displa ...

  • Dell 9.8(0.0) - page 1306

    show ip ospf database network Display the network (type 2) LSA information. Z9500 Syntax show ip ospf process-id database network [ link-state-id ] [adv- router ip-address ] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL ...

  • Dell 9.8(0.0) - page 1307

    Usage Information The following describes the show ip ospf process-id database network command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depend ...

  • Dell 9.8(0.0) - page 1308

    Checksum: 0x4309 Length: 36 Network Mask: /24 Attached Router: 192.10.10.2 Attached Router: 20.20.20.1 Attached Router: 20.20.20.5 Dell# Related Commands show ip ospf database — displays OSPF database information. show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. Z9500 Syntax show ip ospf database nssa-external [ ...

  • Dell 9.8(0.0) - page 1309

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Related Commands show ip ospf database — displays OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information. Z9500 Syntax show ip ospf process-id database opaque-area ...

  • Dell 9.8(0.0) - page 1310

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information The following describes the show ip ospf process-id database opaque- area command shown in ...

  • Dell 9.8(0.0) - page 1311

    Checksum: 0x376 Length: 28 Opaque Type: 1 Opaque ID: 1 Unable to display opaque data LS age: 833 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.2 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000002 Checksum: 0x19c2 --More-- Related Commands show ip ospf database — displays OSPF database informa ...

  • Dell 9.8(0.0) - page 1312

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Related Commands show ip ospf database ? ...

  • Dell 9.8(0.0) - page 1313

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Related Commands show ip ospf database ? ...

  • Dell 9.8(0.0) - page 1314

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information The following describe ...

  • Dell 9.8(0.0) - page 1315

    Item Description (Link Data) Identifies the router interface address. Number of TOS Metric Lists the number of TOS metrics. TOS 0 Metric Lists the number of TOS 0 metrics. Example Dell#show ip ospf 100 database router OSPF Router with ID (1.1.1.10) (Process ID 100) Router (Area 0) LS age: 967 Options: (No TOS-capability, No DC, E) LS type: Router L ...

  • Dell 9.8(0.0) - page 1316

    Related Commands show ip ospf database — displays OSPF database information. show ip ospf database summary Display the network summary (type 3) LSA routing information. Z9500 Syntax show ip ospf process-id database summary [ link-state-id ] [adv- router ip-address ] Parameters process-id Enter the OSPF Process ID to show a specific process. If no ...

  • Dell 9.8(0.0) - page 1317

    Version Description 6.1.1.1 Introduced on the E-Series. Usage Information The following describes the show ip ospf process-id database summary command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS- ...

  • Dell 9.8(0.0) - page 1318

    LS age: 9 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.32.0 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000016 Checksum: 0x987c Length: 28 Network Mask: /24 TOS: 0 Metric: 1 LS age: 7 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.33.0 Advertising Router: 1.1.1.10 L ...

  • Dell 9.8(0.0) - page 1319

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. ...

  • Dell 9.8(0.0) - page 1320

    Item Description Timer intervals... This line displays the interface’s timer settings for Hello interval, Dead interval, Transmit Delay (Wait), and Retransmit Interval. Hello due... This line displays the amount time until the next Hello packet is sent out this interface. Neighbor Count... This line displays the number of neighbors and adjacent n ...

  • Dell 9.8(0.0) - page 1321

    show ip ospf neighbor Display the OSPF neighbors connected to the local router. Z9500 Syntax show ip ospf process-id neighbor Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Command Modes EXEC Privilege Command History This guide is platform-spe ...

  • Dell 9.8(0.0) - page 1322

    Example Dell#show ip ospf 34 neighbor Neighbor ID Pri State Dead Time Address Interface Area 20.20.20.7 1 FULL/DR 00:00:32 182.10.10.3 Te 0/0 0.0.0.2 192.10.10.2 1 FULL/DR 00:00:37 192.10.10.2 Te 0/1 0.0.0.1 20.20.20.1 1 FULL/DROTHER00:00:36 192.10.10.4 Te 0/1 0.0.0.1 Dell# show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. ...

  • Dell 9.8(0.0) - page 1323

    • The display output is sorted by prefixes; intra-area ECMP routes are not displayed together. • For Type 2 external routes, Type 1 cost is not displayed. Example Dell#show ip ospf 100 route Prefix Cost Nexthop Interface Area Type 1.1.1.1 1 0.0.0.0 Lo 0 0 Intra-Area 3.3.3.3 2 13.0.0.3 Te 0/47 1 Intra-Area 13.0.0.0 1 0.0.0.0 Te 0/47 0 Intra-Area ...

  • Dell 9.8(0.0) - page 1324

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. ...

  • Dell 9.8(0.0) - page 1325

    Row Heading Description Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets. Other-Q The queue, for transmission or reception, for the link state acknowledgement, database description, and update packets. The following describes the error definit ...

  • Dell 9.8(0.0) - page 1326

    Total Error Hello DDiscr LSReq LSUpd LSAck RX 10 0 8 2 0 0 0 TX 10 0 10 0 0 0 0 OSPF Global Queue Length TxQ-Len RxQ-Len Tx-Mark Rx-Mark Hello-Q 0 0 0 2 LSR-Q 0 0 0 0 Other-Q 0 0 0 0 Error packets (Only for RX) Intf-Down 0 Non-Dr 0 Self-Org 0 Wrong-Len 0 Invld-Nbr 0 Nbr-State 0 Auth-Err 0 MD5-Err 0 Chksum 0 Version 0 AreaMis 0 Conf-Issues 0 No-Buff ...

  • Dell 9.8(0.0) - page 1327

    Related Commands clear ip ospf statistics — clears the packet statistics in all interfaces and neighbors. show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire. Z9500 Syntax show ip ospf process-id timers rate-limit Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ...

  • Dell 9.8(0.0) - page 1328

    show ip ospf topology Display routers in directly connected areas. Z9500 Syntax show ip ospf process-id topology Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide i ...

  • Dell 9.8(0.0) - page 1329

    summary-address To advertise one external route, set the OSPF ASBR. Z9500 Syntax summary-address ip-address mask [not-advertise] [tag tag-value ] To disable summary address, use the no summary-address ip-address mask command. Parameters ip-address Specify the IP address in dotted decimal format of the address to summarize. mask Specify the mask in ...

  • Dell 9.8(0.0) - page 1330

    With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.0 not-advertise to filter out all the routes fall in r ...

  • Dell 9.8(0.0) - page 1331

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. Usage Information Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage. Example Dell# Dell#conf Dell(conf)#router ospf 1 Dell(conf-router ...

  • Dell 9.8(0.0) - page 1332

    Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduce ...

  • Dell 9.8(0.0) - page 1333

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. OSPFv3 Commands The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) remain unchanged. However, OSPFv3 runs on a per-link basis instead of on a per-IP-subnet basis. Most changes w ...

  • Dell 9.8(0.0) - page 1334

    For MD5 authentication, the key must be 32 hex digits (non- encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms ...

  • Dell 9.8(0.0) - page 1335

    area encryption Configure an IPsec encryption policy for OSPFv3 packets in an OSPFv3 area. Z9500 Syntax area area-id encryption ipsec spi number esp encryption- algorithm [key-encryption-type] key authentication-algorithm [key-encryption-type] key Parameters area area-id Area for which OSPFv3 traffic is to be encrypted. For area-id , enter a number ...

  • Dell 9.8(0.0) - page 1336

    Valid values: 0 (key is not encrypted) or 7 (key is encrypted). key Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non- encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). null Causes an encryption policy configured ...

  • Dell 9.8(0.0) - page 1337

    To remove an IPsec encryption policy from an interface, enter the no area area-id encryption spi number command. Related Commands ipv6 ospf encryption – configures an IPsec encryption policy on an OSPFv3 interface. show crypto ipsec policy – display the configuration of IPsec encryption policies. clear ipv6 ospf process Reset an OSPFv3 router p ...

  • Dell 9.8(0.0) - page 1338

    Parameters interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, ...

  • Dell 9.8(0.0) - page 1339

    00:59:27 : OSPFv3INFO: BFD parameters interval 100 min_rx 100 mult 3 role active 00:59:27 : OSPFv3INFO: BFD parameters interval 100 min_rx 100 mult 3 role active 00:59:27 : OSPFv3INFO: Completed Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 Aug 25 11:19:59: %STKUNIT0-M:CP %BFDMGR-1-BFD_STATE_CHANGE: Changed session state to Init fo ...

  • Dell 9.8(0.0) - page 1340

    Version Description 7.4.1.0 Introduced on E-Series. Example Dell#debug ipv6 ospf packet OSPFv3 packet related debugging is on for all interfaces 05:21:01 : OSPFv3: Sending, Ver:3, Type:1(Hello), Len:40, Router ID:223.255.255.254, Area ID:0, Inst:0, on Po 255 05:21:03 : OSPFv3: Received, Ver:3, Type:1(Hello), Len:40, Router ID:223.255.255.255, Area ...

  • Dell 9.8(0.0) - page 1341

    default-information originate Configure the system to generate a default external route into an OSPFv3 routing domain. Z9500 Syntax default-information originate [always] [metric metric-value ] [metric-type type-value ] [route-map map-name ] To return to the default values, use the no default-information originate command. Parameters always (OPTION ...

  • Dell 9.8(0.0) - page 1342

    graceful-restart grace-period Enable OSPFv3 graceful restart globally by setting the grace period (in seconds) that an OSPFv3 router’s neighbors continues to advertise the router as adjacent during a graceful restart. Z9500 Syntax graceful-restart grace-period seconds To disable OSPFv3 graceful restart, enter no graceful-restart grace- period . P ...

  • Dell 9.8(0.0) - page 1343

    graceful-restart mode Specify the type of events that trigger an OSPFv3 graceful restart. Z9500 Syntax graceful-restart mode {planned-only | unplanned-only} To disable graceful restart mode, enter no graceful-restart mode . Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned rest ...

  • Dell 9.8(0.0) - page 1344

    ipv6 ospf area Enable IPv6 OSPF on an interface. Z9500 Syntax ipv6 ospf process id area area id To disable OSPFv6 routing for an interface, use the no ipv6 ospf process-id area area-id command. Parameters process-id Enter the process identification number. area area-id Specify the OSPF area. The range is from 0 to 65535. Defaults none Command Modes ...

  • Dell 9.8(0.0) - page 1345

    key- encryption- type (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). key Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non- encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 ...

  • Dell 9.8(0.0) - page 1346

    show crypto ipsec sa ipv6 – displays the security associations set up for OSPFv3 interfaces in authentication policies. ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters. Z9500 Syntax ipv6 ospf bfd all-neighbors [disable | [interval interval min_rx min_rx m ...

  • Dell 9.8(0.0) - page 1347

    Version Description 9.2(1.0) Introduced on the Z9500. 9.2.0.0 Introduced on the Z9000, S4820T, and S4810. Usage Information This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set ...

  • Dell 9.8(0.0) - page 1348

    Using this formula, the default path cost is calculated as: • 10-Gigabit Ethernet—Default cost is 1 • 40-Gigabit Ethernet — Default cost is 1 ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down. Z9500 Syntax ipv ...

  • Dell 9.8(0.0) - page 1349

    ipv6 ospf encryption Configure an IPsec encryption policy for OSPFv3 packets on an IPv6 interface. Z9500 Syntax ipv6 ospf encryption {null | ipsec spi number esp encryption- algorithm [ key-encryption-type ] key athentication-algorithm [ key-encryption-type ] key }} Parameters null Causes an encryption policy configured for the area to not be inher ...

  • Dell 9.8(0.0) - page 1350

    For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the ...

  • Dell 9.8(0.0) - page 1351

    ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Z9500 Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject . Defaults The helper-reject role is not configured. Comm ...

  • Dell 9.8(0.0) - page 1352

    To return to the default time interval, enter no ipv6 ospf hello—interval . Parameters seconds Enter the time interval in seconds as the time between hello packets. The range is from 1 to 65525 seconds. Defaults 10 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other plat ...

  • Dell 9.8(0.0) - page 1353

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced ...

  • Dell 9.8(0.0) - page 1354

    Version Description 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Z9500 Syntax maximum-paths number ...

  • Dell 9.8(0.0) - page 1355

    passive-interface Disable (suppress) sending routing updates on an interface. Z9500 Syntax passive—interface interface To enable sending routing updates on an interface, use the no passive- interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, e ...

  • Dell 9.8(0.0) - page 1356

    On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute into OSPFv3. Z9500 Syntax redistribute {bgp as number }{connected | static}[metric metric- value | metric-type type-va ...

  • Dell 9.8(0.0) - page 1357

    tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPFv3. The range is from 0 to 4294967295 The default is 0 . Defaults Not configured. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the r ...

  • Dell 9.8(0.0) - page 1358

    Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introdu ...

  • Dell 9.8(0.0) - page 1359

    Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series TeraScale. 8.3.19.0 Introduced on the S4820T. Usage Information The show crypto ipsec policy command output displays the AH and ESP parameters configured in IPsec security policies, including the SPI number, keys, an ...

  • Dell 9.8(0.0) - page 1360

    show crypto ipsec policy Command Fields Field Description Policy name Displays the name of an IPsec policy. Policy refcount Number of interfaces on the router that use the policy. Inbound ESP SPI Outbound ESP SPI The encapsulating security payload (ESP) security policy index (SPI) for inbound and outbound links. Inbound ESP Auth Key Outbound ESP Au ...

  • Dell 9.8(0.0) - page 1361

    Defaults No default behavior or values. Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2( ...

  • Dell 9.8(0.0) - page 1362

    IPSecv6 policy name: OSPFv3-1-600 inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : A ...

  • Dell 9.8(0.0) - page 1363

    show ipv6 ospf interface View OSPFv3 interface information. Z9500 Syntax show ipv6 ospf [ process-number ] [vrf vrf-name ] [ interface ] Parameters process- number Enter the OSPF process number. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display neighbors corresponding to that VRF. NOTE: If you do not specify t ...

  • Dell 9.8(0.0) - page 1364

    If you enable BFD at the interface level, show ipv6 ospf interface shows the BFD interval timers. Example Dell#show ipv6 ospf 3 interface tengigabitethernet 1/2 TenGigabitEthernet 1/2 is up, line protocol is up Link Local Address fe80::201:e8ff:fe17:5bbd, Interface ID 67420217 Area 0, Process ID 1, Instance ID 0, Router ID 11.1.1.1 NetworkType BROA ...

  • Dell 9.8(0.0) - page 1365

    Command History Version Description 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.4.2.2 Added support for the display of graceful restart parameters and Type-11 Grace LSAs on E-Series TeraScale routers. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Ser ...

  • Dell 9.8(0.0) - page 1366

    LSA count 6 Rtr LSA Count 2 Net LSA Count 1 Inter Area Pfx LSA Count 1 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 Area 1 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 8 Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area ...

  • Dell 9.8(0.0) - page 1367

    • For a port channel interface, enter the keywords port- channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults none Command Modes EXEC EXEC Privilege Command History Version Description 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 ...

  • Dell 9.8(0.0) - page 1368

    • holdtime = 10 seconds Command Modes ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0) Intr ...

  • Dell 9.8(0.0) - page 1369

    36 Pay As You Grow The Pay As You Grow (PAYG) software feature allows you to purchase a Z9500 switch with 36 40G ports (144 10G ports) and upgrade to a larger number of ports as your networking needs grow. install license Install the license for Z9500 ports from local flash, a remote server using a file transfer method, or an external flash device. ...

  • Dell 9.8(0.0) - page 1370

    Version Description 9.5(0.1) Introduced on the Z9500. Usage Information If your Z9500 switch has a 36 40G-port license, all 40G ports (144 10G ports) on line card 0 are enabled and usable. You can purchase a license to use additional ports: • 84 40G ports on line cards 0 and 1 (336 10G ports) • 132 40G ports on line cards 0, 1, and 2 (528 10G p ...

  • Dell 9.8(0.0) - page 1371

    show license Check the status of a Z9500 license and display the number of usable ports or verify a license stored on a remote server before you install it. Z9500 Syntax show license [flash:// filepath | ftp:// userid:password@host-ip/ filepath | scp:// userid:password@hostip/filepath | tftp:// host- ip/filepath | usbflash:// filepath ] Parameters ...

  • Dell 9.8(0.0) - page 1372

    Example If no license is installed, information about the factory-installed 36 40G-port or 132 40G-port configuration is displayed. Dell# show license LICENSE INFORMATION Vendor : Dell Product : Dell Force10 Z950 System Service Tag: RtHvKsJ License Service Tag: Current State : HW-Port-License 36 Ports (Fo 0/0-Fo 0/140) Next Boot : HW-Port-License 3 ...

  • Dell 9.8(0.0) - page 1373

    37 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the platform. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particu ...

  • Dell 9.8(0.0) - page 1374

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. Usage Information This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale in ...

  • Dell 9.8(0.0) - page 1375

    Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. Usage Information If you use this command on a local VLT node, all multicast routes from the local PIM TIB, the entire multicast route table, and all the entries in the data plane are deleted. The local VLT node send ...

  • Dell 9.8(0.0) - page 1376

    register (OPTIONAL) Enter the keyword register to view PIM register address in dotted decimal format (A.B.C.D). state (OPTIONAL) Enter the keyword state to view PIM state changes. timer [assert | hello | joinprune | register] (OPTIONAL) Enter the keyword timer to view PIM timers. Enter one of the optional parameters: • assert : to view the assert ...

  • Dell 9.8(0.0) - page 1377

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 ...

  • Dell 9.8(0.0) - page 1378

    hash-mask- length (OPTIONAL) Enter the hash mask length. The range is from zero (0) to 32. The default is 30 . priority (OPTIONAL) Enter the priority used in Bootstrap election process. The range is from zero (0) to 255. The default is zero (0) . Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. F ...

  • Dell 9.8(0.0) - page 1379

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaSc ...

  • Dell 9.8(0.0) - page 1380

    Version Description 9.7(0.0) Removed the in and out parameters. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the p ...

  • Dell 9.8(0.0) - page 1381

    Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced Example Dell(conf)# ip access-list standard map1 Dell(config-std-nacl)# permit 224.0.0.1/24 Dell(config-std-nacl)#exit Dell(conf)#int tengig 1/1 Dell(config-if-te-1/1)# ip pim ingress-interface-map map1 ip pim neighbor-filter To prevent a router from participating in protocol ...

  • Dell 9.8(0.0) - page 1382

    Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Usage Information Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim que ...

  • Dell 9.8(0.0) - page 1383

    ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. Z9500 Syntax ip pim [vrf vrf-name ] register-filter access-list To return to the default, use the no ip pim [vrf vrf-name ] register- filter access-list command. Parameters vrf vrf-name (OPTIONAL) ...

  • Dell 9.8(0.0) - page 1384

    ip pim rp-address Configure a static PIM rendezvous point (RP) address for a group or access-list. Z9500 Syntax ip pim [vrf vrf-name ] rp-address address {group-address group- address mask } [override] To remove an RP address, use the no ip pim [vrf vrf-name ] rp-address address {group-address group-address mask } [override] command. Parameters vrf ...

  • Dell 9.8(0.0) - page 1385

    Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information First-hop routers use this address by to send register packets on behalf of source multicast hosts. The RP addresses are stored in the order in which they are entered. The RP is chosen based ...

  • Dell 9.8(0.0) - page 1386

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduce ...

  • Dell 9.8(0.0) - page 1387

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the port-channels and the S- Series. Usage Information The interface must be enabled (the no shutdown command) and not have the switchport command configured. Multicast must also ...

  • Dell 9.8(0.0) - page 1388

    Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the port-channels and the S- Series. 7.7.1.1 Introduced Usage Information This command configures an expiration ...

  • Dell 9.8(0.0) - page 1389

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. Usage Information This command is appl ...

  • Dell 9.8(0.0) - page 1390

    If the PIM DR flood is not disabled (default setting): • Multicast traffic is transmitted on the egress port towards the PIM DR if the port is not the incoming interface. • Multicast traffic for an unknown group is sent on the port towards the PIM DR. When DR flooding is disabled, multicast traffic for an unknown group is dropped. show ip pim b ...

  • Dell 9.8(0.0) - page 1391

    show ip pim interface View information on the interfaces with IP PIM enabled. Z9500 Syntax show ip pim [vrf vrf-name ] interface Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The followi ...

  • Dell 9.8(0.0) - page 1392

    Field Description Query Intvl Displays the query interval for Router Query messages on that interface (configured with ip pim query-interval command). DR Prio Displays the Designated Router priority value configured on the interface (use the ip pim dr-priority command). DR Displays the IP address of the Designated Router for that interface. The sho ...

  • Dell 9.8(0.0) - page 1393

    Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. Usage Information The following describes the show ip pim neighbor command shown in the following example. Field Description Neighbor address Displays the IP address of the PIM neighbor. Interface List the interface ...

  • Dell 9.8(0.0) - page 1394

    mapping (OPTIONAL) Enter the keyword mapping to display the multicast groups-to-RP mapping and information on how RP is learnt. group-address (OPTIONAL) Enter the multicast group address mask in dotted decimal format to view RP for a specific group. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For comma ...

  • Dell 9.8(0.0) - page 1395

    show ip pim snooping interface Display information on VLAN interfaces with PIM-SM snooping enabled. Syntax show ip pim snooping interface [vlan vlan-id ] Parameters vlan vlan-id (OPTIONAL) Enter a VLAN ID to display information about a specified VLAN configured for PIM-SM snooping. The valid VLAN IDs range is from 1 to 4094. Command Modes • EXEC ...

  • Dell 9.8(0.0) - page 1396

    Example (#2) Dell#show ip pim snooping interface Interface Ver Nbr DR DR Count Prio Vlan 2 v2 3 1 165.87.32.2 show ip pim snooping neighbor Display information on PIM neighbors learned through PIM-SM snooping. Syntax show ip pim snooping neighbor [vlan vlan-id ] Parameters vlan vlan-id (OPTIONAL) Enter a VLAN ID to display information about PIM nei ...

  • Dell 9.8(0.0) - page 1397

    Field Description • v2 = PIM version 2 DR prio/Mode Displays the Designated Router priority and the mode: • 1 = default Designated Router priority (use the ip pim dr-priority command) • DR = Designated Router • S = Sparse mode Example Dell#show ip pim snooping neighbor Neighbor Interface Uptime/Expires Ver DR Prio Address 165.87.32.2 Vl 2 [ ...

  • Dell 9.8(0.0) - page 1398

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series ExaScale. Usage Information The following describes the show ip pim snooping tib commands shown in the following example. Field Description (S, G) Displays the entry in the PIM multicast snooping database. uptime Displays the ...

  • Dell 9.8(0.0) - page 1399

    (*, 225.1.2.1), uptime 00:00:01, expires 00:02:59, RP 165.87.70.1, flags: J Incoming interface: Vlan 2, RPF neighbor 0.0.0.0 Outgoing interface list: TenGigabitEthernet 2/11 RPF 165.87.32.2 00:00:01/00:02:59 TenGigabitEthernet 2/13 Upstream Port -/- Dell#show ip pim snooping tib vlan 2 225.1.2.1 165.87.1.7 PIM Multicast Snooping Table Flags: J/P - ...

  • Dell 9.8(0.0) - page 1400

    Version Description 7.8.1.0 Introduced on the S-Series. Example Dell# show ip pim summary PIM TIB version 495 Uptime 22:44:52 Entries in PIM-TIB/MFC : 2/2 Active Modes : PIM-SNOOPING Interface summary: 1 active PIM interface 0 passive PIM interfaces 3 active PIM neighbors TIB summary: 1/1 (*,G) entries in PIM-TIB/MFC 1/1 (S,G) entries in PIM-TIB/MF ...

  • Dell 9.8(0.0) - page 1401

    group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D). source-address (OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D). Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS ...

  • Dell 9.8(0.0) - page 1402

    Field Description • F = Dell Networking OS is registering this entry for a multicast source • T = packets were received via Shortest Tree Path • J = first packet from the last hop router is received and the entry is ready to switch to SPT • K = acknowledge pending state Incoming interface Displays the reverse path forwarding (RPF) interface ...

  • Dell 9.8(0.0) - page 1403

    show running-config pim Display the current configuration of PIM-SM snooping. Syntax show running-config pim Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networki ...

  • Dell 9.8(0.0) - page 1404

    Defaults none Command Modes EXEC Privilege Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0(1.3) Introduced on the S5000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Related Commands show ipv6 pim tib – displays the IPv6 PIM tree in ...

  • Dell 9.8(0.0) - page 1405

    • hello : to view the IPv6 PIM neighbor keepalive timer • joinprune : to view the expiry timer (join/prune timer) • register : to view the register suppression timer Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Network ...

  • Dell 9.8(0.0) - page 1406

    priority (OPTIONAL) Enter the priority value for Bootstrap election process. The range is from 0 to 255. The default is 0 . Defaults Refer to Parameters. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . ...

  • Dell 9.8(0.0) - page 1407

    Version Description 8.3.12.0 Introduced on the S4810. 7.4.1.0 Introduced on the S6000. Usage Information The router with the largest value assigned to an interface becomes the designated router. If two interfaces contain the same designated router priority value, the interface with the largest interface IP address becomes the designated router. ipv ...

  • Dell 9.8(0.0) - page 1408

    Dell(conf-if-te-1/1)#ipv6 pim join-filter JOIN-FIL_ACL in Dell(conf-if-te-1/1)#ipv6 pim join-filter JOIN-FIL_ACL out ipv6 pim neighbor-filter Prevent the system from forming a PIM adjacency with a neighboring system. Syntax ipv6 pim neighbor-filter { access-list } Parameters access-list Enter the name of a standard access list. Maximum 16 character ...

  • Dell 9.8(0.0) - page 1409

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduc ...

  • Dell 9.8(0.0) - page 1410

    Dell(conf-ipv6-acl)#permit ipv6 any any Dell(conf-ipv6-acl)#exit ipv6 pim rp-address Configure a static PIM rendezvous point (RP) address for a group. First-hop routers use this address to send register packets on behalf of the source multicast host. Syntax ipv6 pim rp-address address group-address group-address mask override To remove an RP addres ...

  • Dell 9.8(0.0) - page 1411

    Usage Information The RP addresses are stored in the order in which they are entered. RP addresses learned via BSR take priority over static RP addresses. Without the override option, the BSR-advertised RPs updates take precedence over the statically configured RPs. ipv6 pim rp-candidate Specify an interface as an RP candidate. Syntax ipv6 pim rp-c ...

  • Dell 9.8(0.0) - page 1412

    ipv6 pim sparse-mode Enable IPv6 PIM sparse mode on the interface. Syntax ipv6 pim sparse-mode To disable IPv6 PIM sparse mode, use the no ipv6 pim sparse-mode command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS C ...

  • Dell 9.8(0.0) - page 1413

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Intr ...

  • Dell 9.8(0.0) - page 1414

    This system is a candidate BSR Candidate BSR address: 14::2, priority: 0, hash mask length: 126 Dell# show ipv6 pim interface Display IPv6 PIM enabled interfaces. Syntax show ipv6 pim interface Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relev ...

  • Dell 9.8(0.0) - page 1415

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. ...

  • Dell 9.8(0.0) - page 1416

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.4.1.0 Introduced on the S6000. Example Dell#show ipv6 pim rp Group RP ff0e::225:1:2:1 14::1 ff0e::225:1:2:2 14::1 ff0e::226:1:2:1 14::1 ff0e::226:1:2:2 14::1 Dell# Example (Mapping) Dell#s ...

  • Dell 9.8(0.0) - page 1417

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0(1.3) Introduced on the S5000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.4.1.0 Introduced Example Dell#show ipv6 pim tib PIM Multicast Routing Table Flags: D - Dense, S - Sparse, C - Connected, ...

  • Dell 9.8(0.0) - page 1418

    38 PIM-Source Specific Mode (PIM-SSM) The protocol-independent multicast source-specific mode (PIM-SSM) commands in this section are supported in the Dell Networking operating system. IPv4 PIM Commands The following commands apply to IPv4 PIM-SM, IPv4 PIM-SSM, and PIM-DM. • clear ip pim tib • debug ip pim • ip pim dr-priority • ip pim neigh ...

  • Dell 9.8(0.0) - page 1419

    NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. access_list_na me Enter the name of the access list. Defaults Default SSM range is 232/8 and ff3x/32 Command Modes CONFIGURATION Command History Version Description 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6 ...

  • Dell 9.8(0.0) - page 1420

    When you remove the SSM ACL, PIM SSM is supported for the default SSM range only. show ip pim ssm-range Display the non-default groups added using the SSM range feature. Z9500 Syntax show ip pim [vrf vrf-name ] ssm-range Defaults none Command Modes • EXEC • EXEC Privilege Command History Version Description 9.7(0.0) Introduced on the S6000-ON. ...

  • Dell 9.8(0.0) - page 1421

    IPv6 PIM Commands The following commands apply to IPv6 PIM-SM and IPv6 PIM-SSM. • clear ipv6 pim tib • debug ip pim • ipv6 pim dr-priority • ipv6 pim join-filter • ipv6 pim query-interval • ipv6 pim neighbor-filter • show ipv6 pim interface • show ipv6 pim neighbor • show ipv6 pim tib IPv6 PIM-Source Specific Mode Commands This se ...

  • Dell 9.8(0.0) - page 1422

    When the ACL rules change, the ACL manager and PIM modules apply the new rules automatically. When you remove the SSM ACL, the default range is restored. When you configure the SSM range, the system supports SSM for the configured group range as well as the default SSM range. show ipv6 pim ssm-range Display the non-default groups added using the SS ...

  • Dell 9.8(0.0) - page 1423

    39 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is support ...

  • Dell 9.8(0.0) - page 1424

    Version Description 8.4.2.0 Introduced on the E-Series TeraScale. 7.7.1.0 Introduced on the E-Series ExaScale. Related Commands ip redirect-list – enables an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple time ...

  • Dell 9.8(0.0) - page 1425

    Usage Information You can apply any number of redirect-groups to an interface. A redirect list can contain any number of configured rules. These rules includes the next-hop IP address where the incoming traffic is to be redirected. If the next hop address is reachable, traffic is forwarded to the specified next hop. Otherwise, the normal routing ta ...

  • Dell 9.8(0.0) - page 1426

    Version Description 6.5.3.0 Introduced on the E-Series ExaScale. permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Z9500 Syntax permit { ip-protocol-number | protocol-type } { source mask | any | host ip-address } { destination mask | any | host ip-address ...

  • Dell 9.8(0.0) - page 1427

    • ack = acknowledgement • fin = finish (no more data from the user) • psh = push function • rst = reset the connection • syn = synchronize sequence number • urg = urgent field operator (OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than ? ...

  • Dell 9.8(0.0) - page 1428

    mask | any | host ip-address } { destination mask | any | host ip-address } [ operator ] To remove this filter, use one of the following: • Use the no seq sequence-number command if you know the filter’s sequence number. • You can also use the no redirect { ip-address | slot/port }| tunnel tunnel-id }[track <obj-id> ] { ip-protocol-numb ...

  • Dell 9.8(0.0) - page 1429

    destination Enter the IP address of the network or host to which the packets are sent. operator (OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port comman ...

  • Dell 9.8(0.0) - page 1430

    To delete a filter, use the no seq sequence-number command. Parameters sequence- number Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the IP address of the forwarding router. ip-protocol- number ...

  • Dell 9.8(0.0) - page 1431

    operator (OPTIONAL) For the TCP and UDP parameters only. Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command parameter.) source port Enter the keywords source-port then the port number to be ...

  • Dell 9.8(0.0) - page 1432

    show cam pbr Display the PBR CAM content. Z9500 Syntax show cam pbr {[interface interface ] | linecard slot-number port-set number ]} [summary] Parameters interface interface Enter the keyword interface then the name of the interface. linecard number Enter the keyword linecard then the slot number. The range is from 0 to 2 . port-set number Enter t ...

  • Dell 9.8(0.0) - page 1433

    00000 1 100 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:00:04:b7:14:25 Vl 1003(0/2) 00000 1 100 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:00:04:b7:14:26 Vl 1004(0/2) 00000 1 100 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:00:00:78:58:11 Vl 1005(0/3) 00000 1 100 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:00:04:b7:14:27 Vl 1006(0/3) 00000 1 100 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:00:04:b7 ...

  • Dell 9.8(0.0) - page 1434

    Vl 1002) , Next-hop reachable (via Vl 1003) , Next-hop reachable (via Vl 1004) , Next-hop reachable (via Vl 1005) , Next-hop reachable (via Vl 1006) , Next-hop reachable (via Vl 1007) , Next-hop reachable (via Vl 1008) Applied interfaces: Vl 100 Dell# 1434 Policy-based Routing (PBR) ...

  • Dell 9.8(0.0) - page 1435

    40 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). • The mo ...

  • Dell 9.8(0.0) - page 1436

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 ...

  • Dell 9.8(0.0) - page 1437

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0) Introduced on the S6000, Z9500, S6000-ON. Related Commands show runni ...

  • Dell 9.8(0.0) - page 1438

    ttl_value IP TTL value of the ERSPAN traffic. The range is from 1 to 255. The default value is 255. drop Monitors only the dropped packets in the Ingress. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Ref ...

  • Dell 9.8(0.0) - page 1439

    rate-limit Configure the rate-limit to limit the mirrored packets. Syntax rate-limit limit To remove the limit, use the no rate-limit limit command. Parameters limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. Defaults 60 Command Modes CONFIGURATION Command History This guide is platform-specific. For command infor ...

  • Dell 9.8(0.0) - page 1440

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Example ...

  • Dell 9.8(0.0) - page 1441

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ...

  • Dell 9.8(0.0) - page 1442

    Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on ...

  • Dell 9.8(0.0) - page 1443

    To disable a monitor source, use the no source interface destination interface direction {rx | tx | both} command. Parameters source interface Enter one of the following keywords and slot/port information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet inte ...

  • Dell 9.8(0.0) - page 1444

    Defaults none Command Modes MONITOR SESSION (conf-mon- sess-session-ID ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0 ...

  • Dell 9.8(0.0) - page 1445

    41 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell Networking operating software. Private VLANs extend the system security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The private VLAN i ...

  • Dell 9.8(0.0) - page 1446

    • Isolated port : An isolated port is a port that, in Layer 2, can only communicate with promiscuous ports that are in the same PVLAN. • Promiscuous port : A promiscuous port is a port that is allowed to communicate with any other port type. • Trunk port : A trunk port carries VLAN traffic across switches: – A trunk port in a PVLAN is alway ...

  • Dell 9.8(0.0) - page 1447

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Related Commands private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN. show arp — ...

  • Dell 9.8(0.0) - page 1448

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1449

    private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Z9500 Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters vlan-list Enter the list of secondary VLANs to associate ...

  • Dell 9.8(0.0) - page 1450

    switchport mode private-vlan — sets PVLAN mode of the selected port. show interfaces private-vlan Display type and status of PVLAN interfaces. Z9500 Syntax show interfaces private-vlan [interface interface ] Parameters interface interface (OPTIONAL) Enter the keyword interface followed by the interface type and slot/port numbers or port-channel n ...

  • Dell 9.8(0.0) - page 1451

    The following describes the show interfaces private-vlan command shown in the Examples below. Field Description Interface Displays the type of interface and associated slot and port number. Vlan Displays the VLAN ID of the designated interface. PVLAN-Type Displays the type of VLAN in which the designated interface resides. Interface Type Displays t ...

  • Dell 9.8(0.0) - page 1452

    community vlan-id (OPTIONAL) Enter the keyword community and a PVLAN ID number to display the configuration for a community PVLAN. interface interface (OPTIONAL) Enter the keyword interface followed by the interface type and slot/port numbers or port-channel number to display the PVLAN configuration for a member interface. The range of Z9500 slot I ...

  • Dell 9.8(0.0) - page 1453

    Field Description Primary Displays the VLAN ID of the designated or associated primary VLAN(s). Secondary Displays the VLAN ID of the designated or associated secondary VLAN(s). Type Displays the type of VLAN in which the listed interfaces reside. Active States whether the interface is operationally up or down. Ports Displays the interface IDs in t ...

  • Dell 9.8(0.0) - page 1454

    Primary : 10 Isolated : 30 Community : 20 Usage Information Note that if the VLAN ID you enter is a primary VLAN, the entire private VLAN output is displayed, as shown below. If the VLAN ID is a secondary VLAN, only its primary VLAN and secondary VLAN properties are displayed, as shown in the second Example below. Example Dell# show vlan private-vl ...

  • Dell 9.8(0.0) - page 1455

    Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8 ...

  • Dell 9.8(0.0) - page 1456

    42 Per-VLAN Spanning Tree Plus (PVST+) The Dell Networking operating software implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. NOTE: For easier command line entry, the plus (+) sign is not used at the command line. description Enter a description of the PVST+. Z9500 Syntax descriptio ...

  • Dell 9.8(0.0) - page 1457

    Related Commands protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Z9500 Syntax disable To enable PVST+, use the no disable command. Defaults Disabled. Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to ...

  • Dell 9.8(0.0) - page 1458

    extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Z9500 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command H ...

  • Dell 9.8(0.0) - page 1459

    Related Commands protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Z9500 Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For com ...

  • Dell 9.8(0.0) - page 1460

    Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands disable — disables PVST+. show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. Z9500 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Par ...

  • Dell 9.8(0.0) - page 1461

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.4.2.1 Support for the optional guard keyword was added on the ...

  • Dell 9.8(0.0) - page 1462

    128.147 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge ----------------------------------------------------- Te 1/0 Root 128.130 128 20000 FWD 20000 P2P No Te 1/1 Altr 128.131 128 20000 BLK 20000 P2P No Te 1/16 Desg 128.146 128 20000 FWD 20000 P2P Yes Te 1/17 Desg 128.147 128 20000 FWD 20000 P2P Yes Example Dell#show spanning-tree pvs ...

  • Dell 9.8(0.0) - page 1463

    TenGigabitEthernet 1/1 of VLAN 2 is LBK_INC discarding Edge port:no (default) port guard :none (default) Link type: point-to-point (auto) bpdu filter:disable (default) Bpdu guard :disable (default) Bpdus sent 152, received 27562 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------------------------------------------------- ...

  • Dell 9.8(0.0) - page 1464

    spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard. Z9500 Syntax spanning-tree pvst {edge-port [bpduguard [shutdown-on- violation]] | err-disable | vlan ...

  • Dell 9.8(0.0) - page 1465

    Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9 ...

  • Dell 9.8(0.0) - page 1466

    Enabling Portfast BPDU guard and loop guard at the same time on a port results in a port that remains in a Blocking state and prevents traffic from flowing through it. For example, when Portfast BPDU guard and loop guard are both configured: • If a BPDU is received from a remote device, BPDU guard places the port in an Err-Disabled Blocking state ...

  • Dell 9.8(0.0) - page 1467

    Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced. Usage Information Some non-Dell Networking systems which have hybrid ports participating in PVST+ transmit two kinds of BPDUs: an 802.1D BPDU and an untagged PVST+ BPDU. Dell Networking systems do not expect PVST+ BPDU on an untagged port. If this happens, the system places th ...

  • Dell 9.8(0.0) - page 1468

    Version Description 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. Usage Information By default, the system implements an optimized flush mechanism for PVST+. This implementation helps in flushing the MAC addresses only when necessary (and less often) allowing for faster convergence during topology changes. However, if a standards-based fl ...

  • Dell 9.8(0.0) - page 1469

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. Related Commands vlan forward-delay — changes the time interval before the system transitions to the Forwarding state. vlan hello-time — change the time interval between BPDUs. vlan max-age — changes the time interval before PVST+ r ...

  • Dell 9.8(0.0) - page 1470

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. Related Commands vlan bridge-priority — sets the bridge-priority value. vlan hello-time — changes ...

  • Dell 9.8(0.0) - page 1471

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. Related Commands vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — chang ...

  • Dell 9.8(0.0) - page 1472

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1473

    43 Quality of Service (QoS) The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. This chapter contains the following sections: • Global Configuration Commands • Per-Port QoS Commands • Policy-Based QoS Commands Global Configuration Commands There is only one global c ...

  • Dell 9.8(0.0) - page 1474

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the C ...

  • Dell 9.8(0.0) - page 1475

    POLICY-OUT mode supersedes the service-class bandwidth-percentage command. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. Z9500 Syntax service-class dot1p-mapping {dot1p0 value | dot1p1 value | dot1p2 value | dot1p3 value | dot1p4 value | dot1p5 value | dot1p6 value | dot1p7 value } Parameters dot1p0 value . ...

  • Dell 9.8(0.0) - page 1476

    service-class dynamic dot1p Honor all 802.1p markings on incoming switched traffic on an interface (from INTERFACE mode) or on all interfaces (from CONFIGURATION mode). A CONFIGURATION mode entry supersedes an INTERFACE mode entry. Z9500 Syntax service-class dynamic dot1p To return to the default setting, use the no service-class dynamic dot1p comm ...

  • Dell 9.8(0.0) - page 1477

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the command to permit configuration on port channels. 6.1.1.1 Introduced on the E-Series. Usage Information To honor all incoming 802.1p markings on incoming switched traffic on the interface, enter this command. By default, this facility is ...

  • Dell 9.8(0.0) - page 1478

    number Enter a weight for the queue as a number in the range of 1 to 15. This parameter applies only if you specify the green or yellow drop precedence. string Enter the WRED profile name. It is a string of up to 32 characters. Or use one of the five pre-defined WRED profile names. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, ...

  • Dell 9.8(0.0) - page 1479

    Parameters service-class Define the mapping between the service class and policy- based QoS or routing. wred Associate WRED with ECN to mark packets instead of dropping them. ecn Cause explicit congestion notification (ECN) to be used to indicate network congestion, rather than dropping packets, queues-list Enter the queue numbers, either as indivi ...

  • Dell 9.8(0.0) - page 1480

    packets in the queue is above the maximum threshold, packets are dropped based on the drop probability. This behavior is the identical treatment a packet receives when WRED is enabled without ECN configured on the router. Example Dell(conf)#service-class wred ecn 0, 3-5, 7 backplane service-pool wred Configure a global buffer pool that serves as a ...

  • Dell 9.8(0.0) - page 1481

    Command History Version Description 9.2.1.0 Introduced on the Z9500 switch. 9.3.0.0 Introduced on the S6000 and Z9000 platforms. Usage Information You can configure only service pools 0 and 1 because the Dell Networking OS uses only these two service pools. The service0 pool is used for lossy queues; the service1 pool is used for lossless (PFC) que ...

  • Dell 9.8(0.0) - page 1482

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. Related Commands service-class dot1p-mapping — Identifies the class map. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on ...

  • Dell 9.8(0.0) - page 1483

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 1484

    Defaults Granularity for commited-rate and peak-rate is Mbps unless you use the kbps option. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history ...

  • Dell 9.8(0.0) - page 1485

    rate Enter the outgoing rate in multiples of 10 Mbps. The range is from 0 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB. The range is from 0 to 10000. The default is 50. Defaults Granularity for rate is Mbps unless you use the kbps option. Command Modes INTERFACE Command History This guide is platform-specific. For command information ab ...

  • Dell 9.8(0.0) - page 1486

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.2(1.0) Introduced on the Z9500. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.1 ...

  • Dell 9.8(0.0) - page 1487

    Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Intro ...

  • Dell 9.8(0.0) - page 1488

    cpu-qos Enter the keyword cpu-qos to create a class map to filter protocol traffic for rate-limiting control-plane traffic (CoPP). Defaults Layer 3 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The fo ...

  • Dell 9.8(0.0) - page 1489

    match mac dot1p — configures a match criterion for a class map based on a dot1p value. match mac vlan — configures a match criterion for a class map based on VLAN ID. service-queue — assigns a class map and QoS policy to different queues. show qos class-map — views the current class map information. clear qos statistics Clears Matched Packe ...

  • Dell 9.8(0.0) - page 1490

    Related Commands show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. Z9500 Syntax description { description } To remove the description, use the no description { description } command. Parameters description Enter a description to identify the policies (80 characters maximum). ...

  • Dell 9.8(0.0) - page 1491

    match ip access-group Configure match criteria for a class map, based on the access control list (ACL). Z9500 Syntax match ip access-group access-group-name [set-ip-dscp value ] To remove ACL match criteria from a class map, use the no match ip access- group access-group-name [set-ip-dscp value] command. Parameters access-group- name Enter the ACL ...

  • Dell 9.8(0.0) - page 1492

    Related Commands class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria. Z9500 Syntax match {ip | ipv6 | ip-any} dscp dscp-list [set-ip-dscp value ] To remove a DSCP value as a match criteria, use the no match {ip | ipv6 | ip-any} dscp dscp-list [[multicast] set-ip-dscp value ...

  • Dell 9.8(0.0) - page 1493

    Version Description 7.7.1.0 Added the keyword multicast . Added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Added support for the DSCP Marking option. 6.2.1.1 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class ...

  • Dell 9.8(0.0) - page 1494

    set-ip-dscp value (OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63. Defaults none Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant ...

  • Dell 9.8(0.0) - page 1495

    Related Commands class-map — identifies the class map. match ip vlan Uses a VLAN as the match criterion for an L3 class map. Z9500 Syntax match ip vlan vlan-id To remove VLAN as the match criterion, use the no match ip vlan vlan-id command. Parameters vlan vlan-id Enter the keyword vlan and then the ID of the VLAN. The range is from 1 to 4094. De ...

  • Dell 9.8(0.0) - page 1496

    Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19 ...

  • Dell 9.8(0.0) - page 1497

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.1.0 Introduced. Usage Information To access this command, enter the class-map command. After the class map is identified, you ...

  • Dell 9.8(0.0) - page 1498

    Related Commands class-map — identifies the class map. policy-aggregate Allow an aggregate method of configuring per-port QoS via policy maps. An aggregate QoS policy is part of the policy map (input/output) applied on an interface. Z9500 Syntax policy-aggregate qos-policy-name To remove a policy aggregate configuration, use the no policy-aggrega ...

  • Dell 9.8(0.0) - page 1499

    policy-map-input Create an input policy map. Z9500 Syntax policy-map-input policy-map-name [layer2] [cpu-qos] To remove an input policy map, use the no policy-map-input policy-map- name [layer2] [cpu-qos] command. Parameters policy-map- name Enter the name of the policy map in character format (32 characters maximum). layer2 (OPTIONAL) Enter the ke ...

  • Dell 9.8(0.0) - page 1500

    Related Commands service-queue — assigns a class map and QoS policy to different queues. policy-aggregate — allows an aggregate method of configuring per-port QoS using policy maps. service-policy input — applies an input policy map to the selected interface. policy-map-output Create an output policy map. Z9500 Syntax policy-map-output policy ...

  • Dell 9.8(0.0) - page 1501

    policy-aggregate — allows an aggregate method of configuring per-port QoS using policy maps. service-policy output — applies an output policy map to the selected interface. qos-policy-input Create a QoS input policy on the router. Z9500 Syntax qos-policy-input qos-policy-name [layer2] [cpu-qos] To remove an existing input QoS policy from the ro ...

  • Dell 9.8(0.0) - page 1502

    Usage Information To specify the name of the input QoS policy, use this command. After the input policy is specified, rate-police is defined. This command enables Qos-Policy-Input Configuration mode — (conf-qos-policy-in). When changing a Service-Queue configuration in a QoS policy map, all QoS rules are deleted and re-added automatically to ensu ...

  • Dell 9.8(0.0) - page 1503

    Version Description 6.1.1.1 Introduced on the E-Series. Usage Information To specify the name of the output QoS policy, use this command. After the output policy is specified, rate-shape, bandwidth-percentage, and WRED can be defined. This command enables Qos-Policy-Output Configuration mode — (conf-qos- policy-out). Related Commands rate shape ? ...

  • Dell 9.8(0.0) - page 1504

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S- Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Informat ...

  • Dell 9.8(0.0) - page 1505

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(1.0) Added support for packets-per-second and committed rate. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Serie ...

  • Dell 9.8(0.0) - page 1506

    To remove the input policy map from the interface, use the no service-policy input policy-map-name [layer2] command. Parameters policy-map- name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. layer2 (OPTIONAL) Enter the keyword layer2 to spe ...

  • Dell 9.8(0.0) - page 1507

    service-policy output Apply an output policy map to the selected interface. Z9500 Syntax service-policy output policy-map-name To remove the output policy map from the interface, use the no service- policy output policy-map-name command. Parameters policy-map- name Enter the name for the policy map in character format (32 characters maximum). You c ...

  • Dell 9.8(0.0) - page 1508

    service-queue Assign a class map and QoS policy to different queues. Z9500 Syntax service-queue queue-id [class-map class-map-name ] [qos-policy qos-policy-name ] To remove the queue assignment, use the no service-queue queue-id [class-map class-map-name ] [qos-policy qos-policy-name ] command. Parameters queue-id Enter the value used to identify a ...

  • Dell 9.8(0.0) - page 1509

    Usage Information There are eight queues per interface on the Z9500. This command assigns a class map or QoS policy to different queues. Related Commands class-map — identifies the class map. service-policy input — applies an input policy map to the selected interface. service-policy output — applies an output policy map to the selected inter ...

  • Dell 9.8(0.0) - page 1510

    Usage Information After the IP DSCP bit is set, other QoS services can then operate on the bit settings. show qos class-map View the current class map information. Z9500 Syntax show qos class-map [ class-name ] Parameters class-name (Optional) Enter the name of a configured class map. Defaults none Command Modes • EXEC • EXEC Privilege Command ...

  • Dell 9.8(0.0) - page 1511

    show qos policy-map View the QoS policy map information. Z9500 Syntax show qos policy-map {summary [ interface ] | detail [ interface ]} Parameters summary interface To view a policy map interface summary, enter the keyword summary and optionally one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interf ...

  • Dell 9.8(0.0) - page 1512

    Version Description 6.2.1.1 Introduced on the E-Series. Example (IPv4) Dell#show qos policy-map detail tengigabitethernet 1/1 Interface TenGigabitEthernet 1/1 Policy-map-input policy Trust diffserv Queue# Class-map-name Qos-policy-name 0 - q0 1 CM1q1 2 CM2q2 3 CM3q3 4 CM4q4 5 CM5q5 6 CM6q6 7 CM7q7 Dell# Example (IPv6) Dell# show qos policy-map deta ...

  • Dell 9.8(0.0) - page 1513

    class class- map-name Enter the keyword class then the class map name. qos-policy- input qos- policy-name Enter the keyword qos-policy-input then the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Netw ...

  • Dell 9.8(0.0) - page 1514

    7 c7 q7 Dell# show qos policy-map-output View the output QoS policy map details. Z9500 Syntax show qos policy-map-output [ policy-map-name ] [qos-policy-output qos-policy-name ] Parameters policy-map- name Enter the policy map name. qos-policy- output qos- policy-name Enter the keyword qos-policy-output then the QoS policy name. Defaults none Comma ...

  • Dell 9.8(0.0) - page 1515

    show qos qos-policy-input View the input QoS policy details. Z9500 Syntax show qos qos-policy-input [ qos-policy-name ] Parameters qos-policy- name Enter the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant D ...

  • Dell 9.8(0.0) - page 1516

    Parameters qos-policy- name Enter the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for t ...

  • Dell 9.8(0.0) - page 1517

    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40–Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about ot ...

  • Dell 9.8(0.0) - page 1518

    Field (EF) Description Queue # Queue Number Queued Bytes Snapshot of the byte count in that queue. Queued Pkts Cumulative packet count in that queue. Matched Pkts The number of packets that matched the class-map criteria. NOTE: When you configure trust , matched packet counters are not incremented in this field. Matched Bytes The number of bytes th ...

  • Dell 9.8(0.0) - page 1519

    Version Description 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. Example Dell#show qos wred-profile Wred-profile-name min-threshold max-threshold wred_drop 0 0 wred_ge_y 1024 2048 wred_ge_g 2048 4096 wred_teng_y 4096 8192 wred_teng_g 8192 16384 WRED1 2000 7000 test cam-usage Verify CAM usage for an input policy-map configura ...

  • Dell 9.8(0.0) - page 1520

    Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This feature allows you to determine if the CAM has enough space available before applying the configuration on an interface. An input policy map with both Trust and Class-map configuration, the Class-map rules are ignored and ...

  • Dell 9.8(0.0) - page 1521

    Linecard|Portpipe|CAM Partition|Available CAM|Estimated CAM| Status | | | |per Port | (Allowed ports) 0 0 L2ACL 500 200 Allowed (2) 0 1 L2ACL 100 200 Exception 1 0 L2ACL 1000 200 Allowed (5) 1 1 L2ACL 0 200 Exception … … … 13 1 L2ACL 400 200 Allowed (2) Dell# threshold Specify the minimum and maximum threshold values for the configured WRED p ...

  • Dell 9.8(0.0) - page 1522

    Version Description 6.1.1.1 Introduced on the E-Series. Usage Information To configure the minimum and maximum threshold values for user-defined profiles, use this command. Additionally, to modify the minimum and maximum threshold values for the pre-defined WRED profiles, use this command. If you delete the threshold values of the pre-defined WRED ...

  • Dell 9.8(0.0) - page 1523

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added fallback to the E-Series. 8.2.1.0 Added dot1p to the C-Series and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added dot1p and IPv6 DSC ...

  • Dell 9.8(0.0) - page 1524

    wred Configure a WRED profile for yellow or green traffic. Z9500 Syntax wred {yellow | green} profile-name To remove the WRED drop precedence, use the no wred {yellow | green} [ profile- name] command. Parameters yellow | green Enter the keyword yellow for yellow traffic. A DSCP value of xxx100, xxx101, and xxx110 maps to yellow. Enter the keyword ...

  • Dell 9.8(0.0) - page 1525

    Related Commands wred-profile — creates a WRED profile and name that profile. trust — defines the dynamic classification to trust DSCP. wred weight Configure the weight factor used to determine the average-queue size for WRED and ECN operation. The weight value is used in an output QoS policy applied to a front-end or backplane port. Z9500 Synt ...

  • Dell 9.8(0.0) - page 1526

    To stop marking packets, use the no wred ecn command. Defaults none Command Modes QOS-POLICY-OUT mode Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this comma ...

  • Dell 9.8(0.0) - page 1527

    Parameters wred-profile- name Enter your WRED profile name in character format (32 character maximum). Or use one of the pre-defined WRED profile names. You can configure up to 26 WRED profiles plus the five pre-defined profiles, for a total of 31 WRED profiles. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_g. Defaul ...

  • Dell 9.8(0.0) - page 1528

    available bandwidth or drop the packet due to no ability to send. Traffic marked as red (high drop precedence) is dropped. dscp Sets the number of specific DSCP values for a color map profile to yellow or red. Syntax dscp {yellow | red} [ list-dscp-values ] To remove a color policy map profile, use the no dscp {yellow | red} [ dscp-list ] command. ...

  • Dell 9.8(0.0) - page 1529

    • A DSCP value cannot be in both the yellow and red lists. Setting the red or yellow list with any DSCP value that is already in the other list results in an error and no update to that list is made. • Each color map can only have one list of DSCP values for each color; any DSCP values previously listed for that color that are not in the new DS ...

  • Dell 9.8(0.0) - page 1530

    Example Dell(conf)#qos dscp-color-map mymap Related Commands qos dscp-color-map — associates the DSCP color map profile with an interface so that all IP packets received on it is given a color based on that color map dscp — sets the number of specific DSCP values for color map profile to yellow or red. qos dscp-color-policy Associates the DSCP ...

  • Dell 9.8(0.0) - page 1531

    qos dscp-color-map — configures the DSCP color map. show qos dscp-color-map Display the DSCP color map for one or all interfaces. Syntax show qos dscp-color-map map-name Parameters map-name Enter the name of the color map. Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platfor ...

  • Dell 9.8(0.0) - page 1532

    44 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking operating software supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, refer to the Dell Network ...

  • Dell 9.8(0.0) - page 1533

    clear ip rip Update all the RIP routes in the system routing table. Z9500 Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version h ...

  • Dell 9.8(0.0) - page 1534

    • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the key ...

  • Dell 9.8(0.0) - page 1535

    default-information originate Generate a default route for the RIP traffic. Z9500 Syntax default-information originate [always] [metric metric-value ] [route-map map-name ] To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to enable the switch software to always ...

  • Dell 9.8(0.0) - page 1536

    default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command. Z9500 Syntax default-metric number To return the default metric to the original values, use the no default-metric command. Parameters number Specify a number. The range is from 1 to ...

  • Dell 9.8(0.0) - page 1537

    description Enter a description of the RIP routing protocol. Z9500 Syntax description { description } To remove the description, use the no description { description } command. Parameters description Enter a description to identify the RIP protocol (80 characters maximum). Defaults none Command Modes ROUTER RIP Command History This guide is platfor ...

  • Dell 9.8(0.0) - page 1538

    distance Assign a weight (for prioritization) to all routes in the RIP routing table or to a specific route. Lower weights (“administrative distance”) are preferred. Z9500 Syntax distance weight [ ip-address mask [ prefix-name ]] To return to the default values, use the no distance weight [ ip-address mask ] command. Parameters weight Enter a n ...

  • Dell 9.8(0.0) - page 1539

    distribute-list in Configure a filter for incoming routing updates. Z9500 Syntax distribute-list prefix-list-name in [ interface ] To delete the filter, use the no distribute-list prefix-list-name in command. Parameters prefix-list- name Enter the name of a configured prefix list. interface (OPTIONAL) Identifies the interface type slot/port as one ...

  • Dell 9.8(0.0) - page 1540

    Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Related Commands ip prefix-list — enters PREFIX-LIST mode and configures a prefix list. distribute-list out Configure a filter for outgoing routing updates. Z9500 Syntax distribute-list prefix-list-name out [ interface | bgp | connected | isis |ospf | ...

  • Dell 9.8(0.0) - page 1541

    Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introdu ...

  • Dell 9.8(0.0) - page 1542

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands ip split-horizon — sets the RIP routing updates to exclude routing ...

  • Dell 9.8(0.0) - page 1543

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information If you want the interface to receive both versions of RIP, use the ip rip receive version 1 2 command. Related Commands ip rip send ...

  • Dell 9.8(0.0) - page 1544

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information To enable the interface to send both version of RIP packets, use the ip rip send version 1 2 command. Related Commands ip rip receive ver ...

  • Dell 9.8(0.0) - page 1545

    Version Description 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands ip poison-reverse — sets the prefix for RIP routing updates. maximum-paths Set RIP to forward packets over multiple paths. Z9500 Syntax maximum-paths number To return to the default values, use the no maximum-paths commands. Parameters num ...

  • Dell 9.8(0.0) - page 1546

    neighbor Define a neighbor router with which to exchange RIP information. Z9500 Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command. Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured. Command Modes ROUTER RIP Comma ...

  • Dell 9.8(0.0) - page 1547

    network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command. Syntax network ip-address To disable RIP for a network, use the no network ip-address command. Parameters ip-address Specify an IP network address in dotted decimal format. You cannot specify a subnet. Defaults No RIP network is conf ...

  • Dell 9.8(0.0) - page 1548

    offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. Z9500 Syntax offset-list prefix-list-name {in | out} offset [ interface ] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [ interface ] command. Parameters prefix-list- name Enter the name of an established Prefix lis ...

  • Dell 9.8(0.0) - page 1549

    Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information When the offset metric is applied to an interface, that value takes precedence over an offset value that is not extended to an interface. Related Commands ip prefix-l ...

  • Dell 9.8(0.0) - page 1550

    Version Description 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command is intended for low-speed interfaces. passive-interface Suppress routing updates on a specified interface. Z9500 Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. ...

  • Dell 9.8(0.0) - page 1551

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information Although the passive interface does ...

  • Dell 9.8(0.0) - page 1552

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default ...

  • Dell 9.8(0.0) - page 1553

    Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z ...

  • Dell 9.8(0.0) - page 1554

    Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z ...

  • Dell 9.8(0.0) - page 1555

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information To enable RIP, assign a network address using the network command. Example Dell(conf)#router rip Dell(conf-router_rip)# Related Commands ...

  • Dell 9.8(0.0) - page 1556

    Version Description 6.2.1.1 Introduced on the E-Series. Example Dell(conf-router_rip)#show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 0/1 Dell(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Z9500 Syntax show ip rip database [ ip ...

  • Dell 9.8(0.0) - page 1557

    Usage Information The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned th ...

  • Dell 9.8(0.0) - page 1558

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1559

    holddown Enter the number of seconds to specify a time interval during which the route is marked as unreachable but still sending RIP packets. The holddown value should be at least three times the update timer value. The range is from zero (0) to 4294967295. The default is 180 seconds . flush Enter the number of seconds to specify the time interval ...

  • Dell 9.8(0.0) - page 1560

    version Specify either RIP version 1 or RIP version 2. Z9500 Syntax version {1 | 2} To return to the default version setting, use the no version command. Parameters 1 Enter the keyword 1 to specify RIP version 1. 2 Enter the keyword 2 to specify RIP version 2. Defaults The system sends RIPv1 and receives RIPv1 and RIPv2. Command Modes ROUTER RIP Co ...

  • Dell 9.8(0.0) - page 1561

    45 Remote Monitoring (RMON) Dell Networking operating software remote monitoring (RMON) is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection. RMON supports the following RMON groups, as defined in RFC-2819, RFC-3273, and RFC-3434: • Ethernet Statistics Table; RFC-2819 • Ethernet Statistics ...

  • Dell 9.8(0.0) - page 1562

    variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to tes ...

  • Dell 9.8(0.0) - page 1563

    Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Z9500 Syntax rmon collection history {controlEntry integer } [owner name ] [buckets numbe ...

  • Dell 9.8(0.0) - page 1564

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon collection statistics Enable RMON MIB statistics collection on an interface. Z950 ...

  • Dell 9.8(0.0) - page 1565

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table. Z9500 Syntax rmon event number [log] [trap community ] [description string ] [owner name] To disable RMON ...

  • Dell 9.8(0.0) - page 1566

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon hc-alarm Set an alarm on any MIB object. Z9500 Syntax rmon hc-alarm number variab ...

  • Dell 9.8(0.0) - page 1567

    there is no corresponding rising-threshold event, the value is zero. falling- threshold value event-number Enter the keywords falling-threshold then the value (64 bit) the falling-threshold alarm is either triggered or reset. Then enter the event-number to trigger when the falling threshold exceeds its limit. This value is the same as the alarmFall ...

  • Dell 9.8(0.0) - page 1568

    Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on th ...

  • Dell 9.8(0.0) - page 1569

    Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on th ...

  • Dell 9.8(0.0) - page 1570

    22 1.3.6.1.2.1.1.3 Dell# show rmon events Display the contents of the RMON event table. Z9500 Syntax show rmon events [ index ] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format. Defaults none Command Modes E ...

  • Dell 9.8(0.0) - page 1571

    Example (Brief) Dell#show rmon event br index description ------------------------------ 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 Dell# show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. Z9500 Syntax show rmon hc-alarm [ index ] [brief] Parameters index ...

  • Dell 9.8(0.0) - page 1572

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon hc-alarm 1 RMON high-capacity alarm entry 1 object: 1.3 ...

  • Dell 9.8(0.0) - page 1573

    brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an easy-to-read format Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Net ...

  • Dell 9.8(0.0) - page 1574

    show rmon log Display the contents of the RMON log table. Z9500 Syntax show rmon log [ index ] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON log table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is p ...

  • Dell 9.8(0.0) - page 1575

    4 4 Dell# show rmon statistics Display the contents of RMON Ethernet statistics table. Z9500 Syntax show rmon statistics [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet statistics table in an easy-to-read format. Defaults none ...

  • Dell 9.8(0.0) - page 1576

    over-size packets: 0 fragment errors: 0 jabber errors: 0 collision: 0 64bytes packets: 0 65-127 bytes packets: 0 128-255 bytes packets: 0 256-511 bytes packets: 0 512-1023 bytes packets: 0 1024-1518 bytes packets: 0 owner: 1 status: OK <high-capacity data> HC packets received overflow: 0 HC packets received: 0 HC bytes received overflow: 0 HC ...

  • Dell 9.8(0.0) - page 1577

    46 Rapid Spanning Tree Protocol (RSTP) The Dell Networking operating software implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking ...

  • Dell 9.8(0.0) - page 1578

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. Z9500 Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disa ...

  • Dell 9.8(0.0) - page 1579

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introd ...

  • Dell 9.8(0.0) - page 1580

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1581

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Z9500 Syntax ...

  • Dell 9.8(0.0) - page 1582

    Related Commands hello-time — changes the time interval between BPDUs. max-age — changes the wait time before RSTP refreshes the protocol configuration information. hello-time Set the time interval between the generation of the RSTP bridge protocol data units (BPDUs). Z9500 Syntax hello-time [milli-second] seconds To return to the default value ...

  • Dell 9.8(0.0) - page 1583

    Usage Information The hello time is encoded in BPDUs in increments of 1/256ths of a second. The standard minimum hello time in seconds is 1 second, which is encoded as 256. Millisecond hello times are encoded using values less than 256; the millisecond hello time equals (x/1000)*256. When you configure millisecond hellos, the default hello interval ...

  • Dell 9.8(0.0) - page 1584

    Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Related Commands forward-delay — changes the wait time before RSTP transitions to the Forwarding state. hello-time — changes the time interval between BPDUs. protocol spanning-tree rstp ...

  • Dell 9.8(0.0) - page 1585

    Usage Information RSTP is not enabled when you enter RSTP mode. To enable RSTP globally on the system, use the no disable command from RSTP mode. Example Dell(conf)#protocol spanning-tree rstp Dell(config-rstp)##no disable Related Commands disable — disables RSTP globally on the system. show config View the current configuration for the mode. Onl ...

  • Dell 9.8(0.0) - page 1586

    show spanning-tree rstp Display the RSTP configuration. Z9500 Syntax show spanning-tree rstp [brief] [guard] Parameters brief (OPTIONAL) Enter the keyword brief to view a synopsis of the RSTP configuration information. guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. Comm ...

  • Dell 9.8(0.0) - page 1587

    Field Description Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), disabled (DIS), or shut down (EDS Shut). Guard Type Types of STP guard configured (Root, Loop, or BPDU guard) Example (Brief) Dell#show spanning-tree rstp brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 8192, ...

  • Dell 9.8(0.0) - page 1588

    Port 257 (TenGigabitEthernet 0/0) is LBK_INC Discarding Port path cost 20000, Port priority 128, Port Identifier 128.257 Designated root has priority 32768, address 0001.e801.6aa8 Designated bridge has priority 32768, address 0001.e801.6aa8 Designated port id is 128.257, designated path cost 0 Number of transitions to forwarding state 1 BPDU : sent ...

  • Dell 9.8(0.0) - page 1589

    shutdown-on- violation (OPTIONAL) Enter the keywords shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled. priority priority Enter keyword priority then a value in increments of 16 as the priority. The range is from 0 to 240. The default is 128 . loopguard Enter the keyword loopguard to enable loop ...

  • Dell 9.8(0.0) - page 1590

    If you do not enable shutdown-on-violation , BPDUs are still sent to the RPM CPU. You cannot enable STP root guard and loop guard at the same time on a port. For example, if you configure loop guard on a port on which root guard is already configured, the following error message displays: % Error: RootGuard is configured. Cannot configure LoopGuard ...

  • Dell 9.8(0.0) - page 1591

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. Usage Information By default, the system implements an optimized flush mechanism for R ...

  • Dell 9.8(0.0) - page 1592

    47 Security This chapter contains various types of security commands offered in the Dell Networking operating software. The commands are listed in the following sections: • AAA Accounting Commands • Authorization and Privilege Commands • Obscure Password Command • Authentication and Password Commands • RADIUS Commands • TACACS+ Commands ...

  • Dell 9.8(0.0) - page 1593

    aaa authorization role-only Configure authentication to use the user’s role only when determining if access to commands is permitted. Syntax aaa authorization role-only To return to the default setting, use the no aaa authentication role-only command. Parameters name Enter a text string for the name of the user up to 63 characters. It cannot be o ...

  • Dell 9.8(0.0) - page 1594

    role Changes command permissions for roles. Syntax role mode { { { addrole | deleterole } role-name } | reset } command To delete access to a command, use the no role mode role-name Parameters mode Enter one of the following keywords as the mode for which you are controlling access: configure for CONFIGURATION mode exec for EXEC mode interface for ...

  • Dell 9.8(0.0) - page 1595

    Related Commands userrole show role Display information on permissions assigned to a command, including user role and/or permission level. Syntax show role mode { mode } { command } Parameters command Enter the command’s keywords to assign the command to a certain access level. You can enter one or all of the keywords. mode mode Enter keyword the ...

  • Dell 9.8(0.0) - page 1596

    show userroles Display information on all defined user roles. Syntax show userroles Command Modes EXEC Privilege Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Example Dell#show userroles Role Inheritance Modes netoperator Exec netadmin Exec Config Interface Line Ro ...

  • Dell 9.8(0.0) - page 1597

    Defaults none Command Modes CONFIGURATION Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Usage Information Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first ...

  • Dell 9.8(0.0) - page 1598

    As with authentication and authorization, you must configure AAA Accounting by defining a named list of accounting methods, and then applying that list to various interfaces. aaa accounting Enable AAA Accounting and create a record for monitoring the accounting function. Z9500 Syntax aaa accounting {system | exec | commands level | role role- name ...

  • Dell 9.8(0.0) - page 1599

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Added support for roles on the Z9500. 9.5 ...

  • Dell 9.8(0.0) - page 1600

    aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL. Z9500 Syntax aaa accounting suppress null-username To permit accounting records to users with user name value of NULL, use the no aaa accounting suppress null-username command. Defaults Accounting records are recorded for all users. Comma ...

  • Dell 9.8(0.0) - page 1601

    Parameters exec Enter the keyword exec to apply an EXEC level accounting method list. commands { level | role role-name } Enter the keywords commands level to apply an EXEC and CONFIGURATION level accounting method list by enter the keyword role and then the role name for accounting of commands executed by a user with that user role. method-list En ...

  • Dell 9.8(0.0) - page 1602

    show accounting Display the active accounting sessions for each online user. Z9500 Syntax show accounting Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Network ...

  • Dell 9.8(0.0) - page 1603

    Authorization and Privilege Commands To set command line authorization and privilege levels, use the following commands. authorization Apply an authorization method list to terminal lines. Z9500 Syntax authorization { exec | commands { level | role role-name }} method-list Parameters exec Enter the keyword exec to apply an EXEC level authorization ...

  • Dell 9.8(0.0) - page 1604

    Version Description 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. Related Commands aaa authorization commands — sets the parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands aaa authorization exec — sets the parameters that restrict (or permit) a user’s access to EXEC level ...

  • Dell 9.8(0.0) - page 1605

    Version Description 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6. ...

  • Dell 9.8(0.0) - page 1606

    Usage Information By default, the aaa authorization commands command configures the system to check both EXEC level and CONFIGURATION level commands. Use the command no aaa authorization config-commands to enable only EXEC- level command checking. aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level comman ...

  • Dell 9.8(0.0) - page 1607

    privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands. Z9500 Syntax privilege mode {level level command | reset command } To delete access to a level and command, use the no privilege mode level level command command. Parameters mode Enter one of the following keywords as the mode for which you are contro ...

  • Dell 9.8(0.0) - page 1608

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE ...

  • Dell 9.8(0.0) - page 1609

    Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ ...

  • Dell 9.8(0.0) - page 1610

    encrypted string for that line of configuration. To verify that you have successfully obscured passwords and keys, use the show running-config command or show startup-config command. If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command. Rela ...

  • Dell 9.8(0.0) - page 1611

    • tacacs+ : use the TACACS+ server(s) configured with the tacacs-server host command. ... method2 (OPTIONAL) In the event of a “no response” from the first method, the system applies the next configured method. Defaults Use the enable password. Command Modes CONFIGURATION Command History This guide is platform-specific. For command informatio ...

  • Dell 9.8(0.0) - page 1612

    aaa authentication login Configure AAA Authentication method lists for user access to EXEC mode ( Enable log-in ). Z9500 Syntax aaa authentication login { method-list-name | default} method [ ... method4 ] To return to the default setting, use the no aaa authentication login { method-list-name | default} command. Parameters method-list- name Enter ...

  • Dell 9.8(0.0) - page 1613

    Version Description 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6. ...

  • Dell 9.8(0.0) - page 1614

    access-class Restrict incoming connections to a particular IP address in a defined IP access control list (ACL). Z9500 Syntax access-class access-list-name To delete a setting, use the no access-class command. Parameters access-list- name Enter the name of an established IP Standard ACL. Defaults Not configured. Command Modes LINE Command History T ...

  • Dell 9.8(0.0) - page 1615

    enable password Change the password for the enable command. Z9500 Syntax enable password [level level ] [ encryption-type ] password To delete a password, use the no enable password [ encryption-type ] password [level level ] command. Parameters level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 ...

  • Dell 9.8(0.0) - page 1616

    Usage Information To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: • Start with a letter, not a number. • Passwords can have a regular expression as the password. To create a password with a regular expressi ...

  • Dell 9.8(0.0) - page 1617

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information Only Dell Networking Technical Support staff use this command. enabl ...

  • Dell 9.8(0.0) - page 1618

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Us ...

  • Dell 9.8(0.0) - page 1619

    default Enter the keyword default to specify that the default method list, created in the aaa authentication login command, is applied to the terminal line. Defaults No authentication is performed on the console lines. Local authentication is performed on the virtual terminal and auxiliary lines. Command Modes LINE Command History This guide is pla ...

  • Dell 9.8(0.0) - page 1620

    password Enter a text string up to 32 characters long. The first character of the password must be a letter. You cannot use spaces in the password. Defaults No password is configured. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li ...

  • Dell 9.8(0.0) - page 1621

    password-attributes Configure the password attributes (strong password). Z9500 Syntax password-attributes [min-length number ] [max-retry number ] [lockout-period minutes ][character-restriction [upper number ] [lower number ] [numeric number ] [special-char number ]] To return to the default, use the no password-attributes [min-length number ] [ma ...

  • Dell 9.8(0.0) - page 1622

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced the lockout-period option on the Z9500. 9.5(0.0) Introduced the lockout-period option on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S ...

  • Dell 9.8(0.0) - page 1623

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Us ...

  • Dell 9.8(0.0) - page 1624

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example Dell#show privilege Current privilege level is 15 Dell# Related Commands privilege level (CONFIGURATION mode) — assigns access control to differe ...

  • Dell 9.8(0.0) - page 1625

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show users command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lin ...

  • Dell 9.8(0.0) - page 1626

    • AUX: the range is from 1 to 300 seconds, the default is 0 seconds (no timeout). Defaults See the defaults settings shown in Parameters . Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a lis ...

  • Dell 9.8(0.0) - page 1627

    nopassword Enter the keyword nopassword to specify that the user should not enter a password. password Enter the keyword password then the encryption-type or the password. secret Enter the keyword secret then the encryption-type or the password. encryption- type Enter an encryption type for the password that you enter. • 0 directs the system to s ...

  • Dell 9.8(0.0) - page 1628

    Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for the secret option and the MD5 password encryption. Extended the name from 25 to 63 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information To view the defined user names, use the show runni ...

  • Dell 9.8(0.0) - page 1629

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections. Z9500 Syntax ip radius source-interface int ...

  • Dell 9.8(0.0) - page 1630

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. radius-server deadtime Configure a time interval during whi ...

  • Dell 9.8(0.0) - page 1631

    Version Description 6.1.1.0 Introduced on the E-Series. radius-server host Configure a RADIUS server host. Z9500 Syntax radius-server host { hostname | ipv4-address | ipv6-address } [auth-port port-number ] [retransmit retries ] [timeout seconds ] [key [ encryption-type ] key ] Parameters hostname Enter the name of the RADIUS server host. ipv4-addr ...

  • Dell 9.8(0.0) - page 1632

    Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 1633

    radius-server key Configure a key for all RADIUS communications between the switch and the RADIUS host server. Z9500 Syntax radius-server key [ encryption-type ] key To delete a password, use the no radius-server key command. Parameters encryption- type (OPTIONAL) Enter either zero ( 0 ) or 7 as the encryption type for the key entered. The options ...

  • Dell 9.8(0.0) - page 1634

    If you configure the key parameter in the radius-server host command, the key configured with the radius-server key command is the default key for all RADIUS communications. Related Commands radius-server host — configures a RADIUS host. radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADI ...

  • Dell 9.8(0.0) - page 1635

    Related Commands radius-server host — configures a RADIUS host. radius-server timeout To reply to a request, configure the amount of time the RADIUS client (the switch) waits for a RADIUS host server . Z9500 Syntax radius-server timeout seconds To return to the default value, use the no radius-server timeout command. Parameters seconds Enter the ...

  • Dell 9.8(0.0) - page 1636

    TACACS+ Commands The Dell Networking OS supports TACACS+ as an alternate method for login authentication. debug tacacs+ To assist with troubleshooting, view TACACS+ transactions. Z9500 Syntax debug tacacs+ To disable debugging of TACACS+, use the no debug tacacs+ command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is ...

  • Dell 9.8(0.0) - page 1637

    • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16838. • For the Null interface, enter the keywords null 0 . • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slo ...

  • Dell 9.8(0.0) - page 1638

    port number (OPTIONAL) Enter the keyword port then a number as the port to be used by the TACACS+ server. The range is from zero (0) to 65535. The default is 49 . timeout seconds (OPTIONAL) Enter the keyword timeout then the number of seconds the switch waits for a reply from the TACACS+ server. The range is from 0 to 1000. The default is 10 second ...

  • Dell 9.8(0.0) - page 1639

    tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server key Configure a key for communication between a TACACS+ server and a client. Z9500 Syntax tacacs-server key [ encryption-type ] key To delete a key, use the no tacacs-server key key command. Parameters encryption- type (OPTIONAL) Enter either zero ( 0 ) or 7 as the ...

  • Dell 9.8(0.0) - page 1640

    Port Authentication (802.1X) Commands An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the por ...

  • Dell 9.8(0.0) - page 1641

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. Related Commands dot1x authentication (Interface) — enables dot1x on an interface. dot1x authentication (In ...

  • Dell 9.8(0.0) - page 1642

    dot1x auth-fail-vlan Configure an authentication failure VLAN for users and devices that fail 802.1X authentication. Z9500 Syntax dot1x auth-fail-vlan vlan-id [max-attempts number ] To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number ] command. Parameters vlan-id Enter the VLAN Identifier. The ran ...

  • Dell 9.8(0.0) - page 1643

    show dot1x interface — displays the 802.1X information on an interface. dot1x auth-server Configure the authentication server to RADIUS. Z9500 Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networki ...

  • Dell 9.8(0.0) - page 1644

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1645

    Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced ...

  • Dell 9.8(0.0) - page 1646

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. Related Commands interface range — configures a range of interfaces. dot1x port-control Enable port control on an interface. Z9500 Syntax dot1x port-control {force-authorized | ...

  • Dell 9.8(0.0) - page 1647

    Usage Information The authenticator performs authentication only when port-control is set to auto . dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Z9500 Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command. Parameters seconds Ente ...

  • Dell 9.8(0.0) - page 1648

    Parameters interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated. The range is from 1 to 31536000 (1 year). The default is 3600 (1 hour) . Defaults 3600 seconds (1 hour) Command Modes INTERFACE Command History This guide is platform-specific. For command information abo ...

  • Dell 9.8(0.0) - page 1649

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Conf ...

  • Dell 9.8(0.0) - page 1650

    dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Z9500 Syntax dot1x supplicant-timeout seconds To return to the default, use the no dot1x supplicant-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The de ...

  • Dell 9.8(0.0) - page 1651

    Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. ...

  • Dell 9.8(0.0) - page 1652

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. Example Dell#show dot1x int Te 2/32 802.1x information on Te 2/32: ------ ...

  • Dell 9.8(0.0) - page 1653

    Parameters rsa Enter the keyword rsa then the key size to generate a SSHv2 RSA host keys. The range is from 1024 to 2048 if you did not enable FIPS mode; if you enabled FIPS mode, you can only generate a 2048-bit key. The default is 1024 . NOTE: You must have a license to access the FIPS mode. For more information, contact your Dell Networking repr ...

  • Dell 9.8(0.0) - page 1654

    Host key already exists. Do you want to replace. [y/n] :y Dell(conf)# Related Commands ip ssh server — enables the SSH server. show crypto — displays the SSH host public keys. crypto key zeroize rsa Removes the generated RSA host keys and zeroize the key storage location. Syntax crypto key zeroize rsa Defaults none Command Modes CONFIGURATION C ...

  • Dell 9.8(0.0) - page 1655

    Defaults Disabled on both client and server. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Intro ...

  • Dell 9.8(0.0) - page 1656

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command. Related Commands ip ssh serve ...

  • Dell 9.8(0.0) - page 1657

    Usage Information This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh connection-rate-limit Configure the maximum number of incoming SSH connections per minute. Z ...

  • Dell 9.8(0.0) - page 1658

    Parameters enable Enter the keyword enable to enable hostbased- authentication for SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Ne ...

  • Dell 9.8(0.0) - page 1659

    Parameters 512-869 Enter the key-size number for the server-generated RSA SSHv1 key. The range is from 512 to 869. The default is 768 . Defaults Key size 768 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guid ...

  • Dell 9.8(0.0) - page 1660

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Us ...

  • Dell 9.8(0.0) - page 1661

    Usage Information This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command on ...

  • Dell 9.8(0.0) - page 1662

    Command Modes CONFIGURATION mode Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.5(0.0) In ...

  • Dell 9.8(0.0) - page 1663

    Usage Information This command specifies the rhost file used for host-based authentication. This creates/ file overwrites the flash:/ADMIN_DIR/ssh/shosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command once ...

  • Dell 9.8(0.0) - page 1664

    Usage Information Enabling RSA authentication allows the user to log in without being prompted for a password. In addition, the OpenSSH compatible SSHv2 RSA public key must be added to the list of authorized keys ( ip ssh rsa-authentication my- authorized-keys device://filename command). Related Commands ip ssh rsa-authentication (EXEC) — adds ke ...

  • Dell 9.8(0.0) - page 1665

    flash://ADMIN_DIR/ssh/authorized-keys-username (where username is the user associated with this terminal). NOTE: The no form of this command deletes the file flash://ADMIN_DIR/ ssh/ authorized-keys-username file. Related Commands show ip ssh rsa-authentication — displays the RSA authorized keys. ip ssh rsa-authentication (Config) — enables RSA ...

  • Dell 9.8(0.0) - page 1666

    • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr mac hmac- algorithm Enter the keyword mac then a space-delimited list of hash message authentication code (HMAC) algorithms supported by the SSH server for keying hashing for the message authentication. The following HMAC algorithms are available: • hmac-sha1 • hmac-sha1-96 • hmac-sh ...

  • Dell 9.8(0.0) - page 1667

    • diffie-hellman-group14-sha1 port port- number (OPTIONAL) Enter the keyword port then the port number of the listening port of the SSH server. The range is from 1 to 65535. The default is 22 . [version {1 | 2}] (OPTIONAL) Enter the keyword version then the SSH version 1 or 2 to specify only SSHv1 or SSHv2. NOTE: If you enable FIPS mode, you can ...

  • Dell 9.8(0.0) - page 1668

    Version Description 6.1.1.0 Introduced on the E-Series. Usage Information This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22. Example Dell# conf Dell(conf)# ip ssh server port 45 Dell(conf)# ip ssh server enable Dell# Related Commands show ip ssh — displays the ssh i ...

  • Dell 9.8(0.0) - page 1669

    Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information The source-interface interface attribute is applicable for both the SSH client as well as the COPY (SCP) commands. Using these attributes the client session tags an error to the user during run time, in case there is a mismatch bet ...

  • Dell 9.8(0.0) - page 1670

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information This command is useful if the remote SSH client implements Strict Host Key Checking. You can copy the host key to your list of known host ...

  • Dell 9.8(0.0) - page 1671

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example Dell#sh ip ssh SSH server : enabled. SSH server version : v1 and v2. Password ...

  • Dell 9.8(0.0) - page 1672

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash://ADMIN_DIRssh/ knownhosts file. Example Dell#show ip ssh client-pub-keys poclab4,123.12.1.123 ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAox/ QQp8xYhzOxn07yh4VGPAo ...

  • Dell 9.8(0.0) - page 1673

    Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash:/ADMIN_DIR/ssh/ authorized-keys.username file. Example Dell#show ip ssh rsa-authentication my-authorized-keys ssh-rsa AAAAB ...

  • Dell 9.8(0.0) - page 1674

    hostname (OPTIONAL) Enter the IP address or the host name of the remote device. vrf instance (OPTIONAL) E-Series Only: Enter the keyword vrf then the VRF Instance name to open an SSH connection to that instance. ipv4 address (OPTIONAL) Enter the IP address in dotted decimal format A.B.C.D. ipv6-address prefix-length (OPTIONAL) Enter the IPv6 addres ...

  • Dell 9.8(0.0) - page 1675

    -v {1 | 2} (OPTIONAL) Enter the keyword -v then the SSH version 1 or 2. The default is the version from the protocol negotiation. Defaults As shown in the Parameters section. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command L ...

  • Dell 9.8(0.0) - page 1676

    -p SSH server port option (default 22) -v SSH protocol version <cr> Dell#ssh 10.11.8.12 -c ? 3des-cbc Force ssh to use 3des-cbc encryption cipher Dell#ssh 10.11.8.12 -m ? hmac-sha1 Force ssh to use hmac-sha1 HMAC algorithm hmac-sha1-96 Force ssh to use hmac-sha1-96 HMAC algorithm hmac-md5 Force ssh to use hmac-md5 HMAC algorithm hmac-md5-96 F ...

  • Dell 9.8(0.0) - page 1677

    ip dhcp relay Enable Option 82. Z9500 Syntax ip dhcp relay information-option [trust-downstream] Parameters trust- downstream Configure the system to trust Option 82 when it is received from the previous-hop router. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other pl ...

  • Dell 9.8(0.0) - page 1678

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information When enabled, no learning takes place until you enable snooping on a VLAN. After disabling DHCP Snooping, the binding table is ...

  • Dell 9.8(0.0) - page 1679

    Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8. ...

  • Dell 9.8(0.0) - page 1680

    Version Description 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping database renew Renew the binding table. Z9500 Syntax ip dhcp snooping database renew Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell ...

  • Dell 9.8(0.0) - page 1681

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable IP source guard. Z9500 Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes IN ...

  • Dell 9.8(0.0) - page 1682

    Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z950 ...

  • Dell 9.8(0.0) - page 1683

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Related Commands clear ip dhcp snooping — clears the contents of the DHCP binding table. Security 1683 ...

  • Dell 9.8(0.0) - page 1684

    48 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command line information (CLI) for the Dell Networking operat ...

  • Dell 9.8(0.0) - page 1685

    Parameters interface Enter one of the following interfaces and slot/port information: • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, ent ...

  • Dell 9.8(0.0) - page 1686

    protocol-tunnel Enable protocol tunneling on a stacked (Q-in-Q) VLAN for specified protocol packets. Z9500 Syntax protocol-tunnel {rate-limit rate | stp} To disable protocol tunneling for a Layer 2 protocol, use the no protocol- tunnel command. Parameters rate-limit rate Enter the keyword rate-limit followed by a number for the rate-limit for tunne ...

  • Dell 9.8(0.0) - page 1687

    protocol-tunnel destination-mac Overwrite the BPDU destination MAC address with a specific value. Z9500 Syntax protocol-tunnel destination-mac xstp address Parameters stp Change the default destination MAC address used for L2PT to another value. Defaults The default destination MAC is 01:01:e8:00:00:00. Command Modes CONFIGURATION Command History T ...

  • Dell 9.8(0.0) - page 1688

    Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z950 ...

  • Dell 9.8(0.0) - page 1689

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, E-Series TeraScale, and E- Series ExaScale. Maximum rate limit on E-Series reduced from 4000 to 3000. 7.4.1.0 Introduced Example Dell# Dell#conf Dell(conf)#pr ...

  • Dell 9.8(0.0) - page 1690

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, E-Series and E-Series ExaScale. 7.4.1.0 Introduced Example Dell#show protocol-tunnel System Rate-Limit: 75 frames/second VLAN Protocols Interface 1000 STP,PVS ...

  • Dell 9.8(0.0) - page 1691

    49 sFlow sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flow ...

  • Dell 9.8(0.0) - page 1692

    sflow collector Configure a collector device to which sFlow datagrams are forwarded. Z9500 Syntax sflow collector { ip-address | ipv6-address } agent-addr { ip- address | ipv6-address } [ number [max-datagram-size number ]] | [max-datagram-size number ] To delete a configured collector, use the no sflow collector { ip-address | ipv6-address } agent ...

  • Dell 9.8(0.0) - page 1693

    Version Description 8.4.2.3 Added support for IPv6 sFlow collectors and agents on the E-series TeraScale, C-Series, and S-Series. 8.4.1.1 Added support for IPv6 sFlow collectors and agents on the E-series ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced ...

  • Dell 9.8(0.0) - page 1694

    Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z950 ...

  • Dell 9.8(0.0) - page 1695

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on th ...

  • Dell 9.8(0.0) - page 1696

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1697

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S Series and Z ...

  • Dell 9.8(0.0) - page 1698

    Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information The polling interval for an interface is the maximum number of seconds between successive samples of counters sent to the collector. This command changes the global default counter polling (20 seconds) in ...

  • Dell 9.8(0.0) - page 1699

    Version Description 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This command sets the counter polling interval for an interface. Related Commands sflow polling-interval (Global) — ...

  • Dell 9.8(0.0) - page 1700

    Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This ...

  • Dell 9.8(0.0) - page 1701

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ...

  • Dell 9.8(0.0) - page 1702

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1703

    show sflow linecard Display sFlow information for a line card. Z9500 Syntax show sflow linecard slot-id Parameters slot number Enter a slot number to view information on the line-card ports in that slot. The range of Z9500 slot IDs is from 0 to 2. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command ...

  • Dell 9.8(0.0) - page 1704

    Samples rcvd from h/w :0 Total UDP packets exported :0 UDP packets exported via RPM :0 UDP packets dropped :0 Dell# 1704 sFlow ...

  • Dell 9.8(0.0) - page 1705

    50 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. The chapter contains the following sections: • SNMP Commands • Syslog Commands SNMP Commands The following SNMP commands are available in the Dell Networking operating ...

  • Dell 9.8(0.0) - page 1706

    show snmp Display the status of SNMP network elements. Z9500 Syntax show snmp Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version hist ...

  • Dell 9.8(0.0) - page 1707

    show snmp engineID Display the identification of the local SNMP engine and all remote engines that are configured on the router. Z9500 Syntax show snmp engineID Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li ...

  • Dell 9.8(0.0) - page 1708

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1709

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Example Dell#show snmp user User name: v1v2creadu Engine ID: 0000178B02000001E80214A8 storage-type: nonvolatile active Authentication Protocol: None Privacy ...

  • Dell 9.8(0.0) - page 1710

    to Router2. This is a port connected to IF-MIB::ifAlias.134792448 = STRING: !----command run on Force10 switch:-----------! Dell#snmp ifmib ifalias long !----command run on server connected to switch:------! > snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Ro ...

  • Dell 9.8(0.0) - page 1711

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1712

    guestuser Dell(conf)# Example Dell(conf)# ip access-list standard snmp-ro-acl Dell(config-std-nacl)#seq 5 permit host 10.10.10.224 Dell(config-std-nacl)#seq 10 deny any count ! Dell(conf)#snmp-server community guest ro snmp-ro-acl Dell(conf)# Related Commands ip access-list standard — names (or selects) a standard access list to filter based on I ...

  • Dell 9.8(0.0) - page 1713

    Version Description 7.5.1.0 Introduced on the C-Series. snmp-server enable traps Enable SNMP traps. Z9500 Syntax snmp-server enable traps [ notification-type ] [ notification- option ] To disable traps, use the no snmp-server enable traps [ notification- type ] [ notification-option ] command. Parameters notification- type Enter the type of notific ...

  • Dell 9.8(0.0) - page 1714

    • temperature For the snmp notification-type, enter one of the following optional parameters: • authentication • coldstart • linkdown • linkup Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li ...

  • Dell 9.8(0.0) - page 1715

    snmp-server engineID Configure the name for both the local and remote SNMP engines on the router. Z9500 Syntax snmp-server engineID [local engineID ] [remote ip-address udp- port port-number engineID ] To return to the default, use the no snmp-server engineID [local engineID ] [remote ip-address udp-port port-number engineID ] command. Parameters l ...

  • Dell 9.8(0.0) - page 1716

    Usage Information Changing the value of the SNMP Engine ID has important side effects. A user’s password (entered on the command line) is converted to a message digest algorithm (MD5) or secure hash algorithm (SHA) security digest. This digest is based on both the password and the local Engine ID. The command line password is then destroyed, as r ...

  • Dell 9.8(0.0) - page 1717

    The default is 1 . auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. noauth (OPTIONAL) Enter the keyword noauth to specify no authentication of a packet. priv (OPTIONAL) Enter the keyword priv to specify both authentication and then scrambling of the packet. read name (OPTIONAL) Enter the keyword read ...

  • Dell 9.8(0.0) - page 1718

    Usage Information The following Example specifies the group named harig as a version 3 user requiring both authentication and encryption and read access limited to the read named rview . NOTE: The number of configurable groups is limited to 16 groups. Example Dell#conf Dell(conf)# snmp-server group harig 3 priv read rview Dell# Related Commands sho ...

  • Dell 9.8(0.0) - page 1719

    • Version 2c allows transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. The default is version 1 . auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. noauth (OPTIONAL) Enter the keyword noauth to specify no authentication of a packet. priv (OP ...

  • Dell 9.8(0.0) - page 1720

    Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z950 ...

  • Dell 9.8(0.0) - page 1721

    NOTE: For v1 / v2c trap configuration, if the community-string is not defined using the snmp-server community command prior to using this command, the default form of the snmp-server community command automatically is configured with the community-name the same as specified in the snmp- server host command. Configuring Informs To send an inform, us ...

  • Dell 9.8(0.0) - page 1722

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Example Dell(conf)#snmp-server location MAA_LAB Dell(conf)#do show running-config snmp ! snmp-server community public ro snmp-server location MAA_LAB Related Commands show running-config snmp — displays the SNMP running configuration. snmp-server packetsiz ...

  • Dell 9.8(0.0) - page 1723

    snmp-server trap-source Configure a specific interface as the source for SNMP traffic. Z9500 Syntax snmp-server trap-source interface To disable sending traps out a specific interface, use the no snmp trap-source command. Parameters interface Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the k ...

  • Dell 9.8(0.0) - page 1724

    Related Commands snmp-server community — sets the community string. snmp-server user Configure a new user to an SNMP group. Z9500 Syntax snmp-server user name { group_name remote ip-address udp-port port-number } [1 | 2c | 3] [encrypted] [auth {md5 | sha} auth- password ] [priv des56 priv password ] [access access-list-name | ipv6 access-list-nam ...

  • Dell 9.8(0.0) - page 1725

    encrypted (OPTIONAL) Enter the keyword encrypted to specify the password appear in encrypted format (a series of digits, masking the true characters of the string). auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. md5 | sha (OPTIONAL) Enter the keyword md5 or sha to designate the authentication level. ...

  • Dell 9.8(0.0) - page 1726

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information NOTE: For IPv6 ACLs, only IPv6 and UDP types are valid for SNMP. TCP and ICMP rules are not valid for SNMP. In IPv6 ACLs port rules are not valid for SNMP. No default values exist for authentication or privacy algorithms and no default pass ...

  • Dell 9.8(0.0) - page 1727

    To remove an SNMPv3 view, use the no snmp-server view view-name oid- tree {included | excluded} command. Parameters view-name Enter the name of the view (not to exceed 20 characters). oid-tree Enter the OID sub tree for the view (not to exceed 20 characters). included (OPTIONAL) Enter the keyword included to include the MIB family in the view. excl ...

  • Dell 9.8(0.0) - page 1728

    snmp trap link-status Enable the interface to send SNMP link traps, which indicate whether the interface is up or down. Z9500 Syntax snmp trap link-status To disable sending link trap messages, use the no snmp trap link-status command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information ...

  • Dell 9.8(0.0) - page 1729

    Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8 ...

  • Dell 9.8(0.0) - page 1730

    default logging buffered Return to the default setting for messages logged to the internal buffer. Z9500 Syntax default logging buffered Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Co ...

  • Dell 9.8(0.0) - page 1731

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Related Commands logging console — sets the logging console parameters. default logging monitor Return to the default settings for messages logged to the ...

  • Dell 9.8(0.0) - page 1732

    default logging trap Return to the default settings for logging messages to the Syslog servers. Z9500 Syntax default logging trap Defaults level = 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refere ...

  • Dell 9.8(0.0) - page 1733

    hostname Enter the name of a host already configured and recognized by the switch. udp Enter the keyword udp to enable transmission of log message over UDP followed by port number. The default port is 514 tcp Enter the keyword tcp to enable transmission of log message over TCP followed by port number. Defaults Disabled. Command Modes CONFIGURATION ...

  • Dell 9.8(0.0) - page 1734

    logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. Z9500 Syntax logging buffered [ level ] [ size ] To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffe ...

  • Dell 9.8(0.0) - page 1735

    Related Commands clear logging — clears the logging buffer. default logging buffered — returns the logging buffered parameters to the default setting. show logging — displays the logging setting and system messages in the internal buffer. logging console Specify which messages are logged to the console. Z9500 Syntax logging console [ level ] ...

  • Dell 9.8(0.0) - page 1736

    default logging console — returns the logging console parameters to the default setting. show logging — displays the logging setting and system messages in the internal buffer. logging extended Logs security and audit events to a system log server. Syntax logging extended Defaults none Command Modes CONFIGURATION Command History This guide is p ...

  • Dell 9.8(0.0) - page 1737

    logging facility Configure the Syslog facility used for error messages sent to Syslog servers. Z9500 Syntax logging facility [ facility-type ] To return to the default values, use the no logging facility command. Parameters facility-type (OPTIONAL) Enter one of the following parameters: • auth (authorization system) • cron (Cron/at facility) ? ...

  • Dell 9.8(0.0) - page 1738

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1739

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network ...

  • Dell 9.8(0.0) - page 1740

    Usage Information When the number of messages reach the limit you set with the logging history size command, older messages are deleted as newer ones are added to the table. Related Commands show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications. Z9500 Syntax logg ...

  • Dell 9.8(0.0) - page 1741

    logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines. Z9500 Syntax logging on To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History ...

  • Dell 9.8(0.0) - page 1742

    logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server. Z9500 Syntax logging source-interface interface To disable this command and return to the default setting, use the no logging source-interface command. Parameters interface Enter the following keywords and slot/ ...

  • Dell 9.8(0.0) - page 1743

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information Syslog messages contain the IP address of the interface used to egress the router. By configuring the logging source-interface command, the Syslog packets contain the IP address of the interface configured. Related Commands logging — enab ...

  • Dell 9.8(0.0) - page 1744

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information When you enable logging synchronous , unsolicited messages appear between software prompts and outputs. Only the messages with a severity ...

  • Dell 9.8(0.0) - page 1745

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to ...

  • Dell 9.8(0.0) - page 1746

    Example Dell(conf)# logging version ? <0-1> Select syslog version (default = 0) Dell(conf)# logging version 1 show logging Display the logging settings and system messages logged to the internal buffer of the switch. Z9500 Syntax show logging [ number | history [reverse][ number ] | reverse [ number ] | summary] Parameters number (OPTIONAL) E ...

  • Dell 9.8(0.0) - page 1747

    (40960 bytes) Trap logging: level informational Logging to 172.16.1.162 Logging to 10.10.10.4 Logging to 10.1.2.4 Logging to 172.31.1.4 Logging to 133.33.33.4 Feb 18 01:17:32: %SYSTEM:CP %SEC-5-LOGOUT: Exec session is terminated for user admin on line vty0 ( 10.16.127.145 ) Feb 18 01:17:31: %SYSTEM:CP %IFMGR-5-ASTATE_DN: Changed interface Admin sta ...

  • Dell 9.8(0.0) - page 1748

    Example (History) Dell#show logging history Syslog History Table: 1 maximum table entries, saving level warnings or higher SNMP notifications not Enabled Feb 18 01:16:57: %SYSTEM:CP %SEC-3- AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success on vty0 ( 10.16.127.145 ) show logging auditlog Displays an audit log. Syntax show logging ...

  • Dell 9.8(0.0) - page 1749

    linecard slot-id Enter the linecard slot-id parameters to specify the line-card ports for which you want to display the driver log. The range of line-card slot IDs is from 0 to 2. defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relev ...

  • Dell 9.8(0.0) - page 1750

    9:Task(tUsrRoot): [ 36]SS DRV DEBUG: port:28 isfanout:0 10:Task(tUsrRoot): [ 35]SS DRV DEBUG: port:32 isfanout:0 Usage Information This command displays internal software driver information, which may be useful during troubleshooting switch initialization errors, such as a downed Port-Pipe. show logging kernellog Display the kernel log for the spec ...

  • Dell 9.8(0.0) - page 1751

    failed addr=0x20 cmd_reg=0xf rv=5 00:00:43:418634:PCI unit 0: Dev 0xb852, Rev 0x03, Chip BCM56852_A2, Driver BCM56850_A0 00:00:43:418655:PCI unit 1: Dev 0xb852, Rev 0x03, Chip BCM56852_A2, Driver BCM56850_A0 00:00:43:418671:PCI unit 2: Dev 0xb852, Rev 0x03, Chip BCM56852_A2, Driver BCM56850_A0 00:00:43:418687:PCI unit 3: Dev 0xb852, Rev 0x03, Chip ...

  • Dell 9.8(0.0) - page 1752

    1d 02:26:50:179846:qsfp-6 eeprom attempting to read on from iic at : 24 1d 02:26:50:187498:qsfp-7 eeprom attempting to read on from iic at : 23 1d 02:26:50:202989:qsfp-11 eeprom attempting to read on from iic at : 18 1d 02:28:50:440146:qsfp-0 eeprom attempting to read on from iic at : 17 1d 02:28:50:447933:qsfp-1 eeprom attempting to read on from i ...

  • Dell 9.8(0.0) - page 1753

    Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Related Commands logging monitor — sets the logging parameters on the monitor/terminal. Simple Network Management Protocol (SNMP) and Syslog 1753 ...

  • Dell 9.8(0.0) - page 1754

    51 SNMP Traps This chapter lists the traps sent by the Dell Networking operating system. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Message ID Trap Type Trap Option COLD_START SNMP COLDSTART %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent. WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP Copy Config Co ...

  • Dell 9.8(0.0) - page 1755

    Message ID Trap Type Trap Option %SYSTEM-P:CP %SNMP-4-RMON_FALLING_THRESHOLD: RMON falling threshold alarm from SNMP OID <oid> RMON_HC_RISHING_THRESHOLD SNMP NONE %SYSTEM-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID <oid> RMON_HC_FALLING_THRESHOLD SNMP NONE %SYSTEM-P:CP %SNMP-4-RMON_HC_F ...

  • Dell 9.8(0.0) - page 1756

    Message ID Trap Type Trap Option %CHMGR-5-MINOR_PS_CLR: Minor alarm cleared: power supply redundant CHM_MIN_ALRM_TEMP ENVMON TEMP %CHMGR-2-MINOR_TEMP: Minor alarm: chassis temperature CHM_MIN_ALRM_TEMP_CLR ENVMON TEMP %CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC) CHM_MAJ_ALRM ...

  • Dell 9.8(0.0) - page 1757

    Message ID Trap Type Trap Option %CHMGR-5-FANOK: Minor alarm cleared: all fans in fan tray are good TME_TASK_SUSPEND ENVMON NONE %TME-2-TASK SUSPENDED: SUSPENDED - svce:%d - inst: %d - task:%s TME_TASK_TERM ENVMON NONE %TME-2-ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CHM_CPU_THRESHOLD ENVMON NONE %CHMGR-5-CPU_THRESHOLD: Cpu %s usage above thres ...

  • Dell 9.8(0.0) - page 1758

    52 Storm Control The Dell Networking operating software storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and S- Series). Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks ...

  • Dell 9.8(0.0) - page 1759

    Parameters interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defau ...

  • Dell 9.8(0.0) - page 1760

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list ...

  • Dell 9.8(0.0) - page 1761

    • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list ...

  • Dell 9.8(0.0) - page 1762

    Command Modes CONFIGURATION (conf) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 ...

  • Dell 9.8(0.0) - page 1763

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the perce ...

  • Dell 9.8(0.0) - page 1764

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. Usage Information Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter. It is possible, however, that some multicast control traffi ...

  • Dell 9.8(0.0) - page 1765

    storm-control unknown-unicast (Configuration) Configure the percentage of unknown-unicast traffic allowed in or out of the network. Z9500 Syntax storm-control unknown-unicast [ packets_per_second in] To disable storm control for unknown-unicast traffic, use the no storm-control unknown-unicast [ packets_per_second in] command. Parameters packets_pe ...

  • Dell 9.8(0.0) - page 1766

    storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only). Z9500 Syntax storm-control unknown-unicast [ percentage decimal_value in] | [wred-profile name]] [ packets_per_second in] To disable unknown-unicast storm control on the interface, use the no storm- control unknown-unica ...

  • Dell 9.8(0.0) - page 1767

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series. Storm Control 1767 ...

  • Dell 9.8(0.0) - page 1768

    53 Spanning Tree Protocol (STP) The commands in this chapter configure and monitor the IEEE 802.1d spanning tree protocol (STP). bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs. Z9500 Syntax bpdu-destination-mac-address [xstp | gvrp] provider-bridge- group Parameters xstp Force STP, RSTP, and MSTP to ...

  • Dell 9.8(0.0) - page 1769

    bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree. Z9500 Syntax bridge-priority { priority-value | primary | secondary} To return to the default value, use the no bridge-priority command. Parameters priority-value Enter a number as the bridge priority value. The range is from 0 to 65535. The default is 32768 . pr ...

  • Dell 9.8(0.0) - page 1770

    debug spanning-tree Enable debugging of the spanning tree protocol and view information on the protocol. Z9500 Syntax debug spanning-tree { stp-id [all | bpdu | config | events | exceptions | general | root] | protocol } To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning ...

  • Dell 9.8(0.0) - page 1771

    Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information When you enable debug spanning-tree bpdu for multiple interfaces, the software only sends information on BPDUs for the last interface specified. Related Commands protocol spanning-tree — enters SPANNING TREE mode on the switch. descriptio ...

  • Dell 9.8(0.0) - page 1772

    disable Disable the spanning tree protocol globally on the switch. Z9500 Syntax disable To enable Spanning Tree Protocol, use the no disable command. Defaults Enabled (that is, the spanning tree protocol is disabled.) Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to ...

  • Dell 9.8(0.0) - page 1773

    Parameters seconds Enter the number of seconds the system waits before transitioning STP to the Forwarding state. The range is from 4 to 30. The default is 15 seconds . Defaults 15 seconds Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking ...

  • Dell 9.8(0.0) - page 1774

    Defaults 2 seconds Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z950 ...

  • Dell 9.8(0.0) - page 1775

    Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introdu ...

  • Dell 9.8(0.0) - page 1776

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1777

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Example Dell(config-stp)#show config protocol spanning-tree 0 no disable Dell(config-stp)# show spanning-tree 0 Display the spanning tree group configurati ...

  • Dell 9.8(0.0) - page 1778

    summary (OPTIONAL) Enter the keyword summary to only the number of ports in the spanning tree group and their state. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell ...

  • Dell 9.8(0.0) - page 1779

    Field Description “Timers” Lists the values for the following bridge timers: hold time, topology change, hello time, max age, and forward delay. “Times” List the number of seconds since the last: • hello time • topology change • notification • aging “Port 1...” Displays the Interface type slot/port information and the status of ...

  • Dell 9.8(0.0) - page 1780

    Port path cost 4, Port priority 8, Port Identifier 8.28 Designated root has priority 32768, address 0001.e800.0a56 Designated bridge has priority 32768, address 0001.e800.0a56 Designated port id is 8.28, designated path cost 0 Timers: message age 0, forward_delay 0, hold 0 Number of transitions to forwarding state 1 BPDU: sent:31, received 0 The po ...

  • Dell 9.8(0.0) - page 1781

    spanning-tree 0 Assigns a Layer 2 interface to STP instance 0 and configures a port cost or port priority, or enables loop guard, root guard, or the Portfast feature on the interface. Z9500 Syntax spanning-tree stp-id {cost cost | | portfast [bpduguard [shutdown-on-violation]] | priority priority } To disable Spanning Tree group on an interface, us ...

  • Dell 9.8(0.0) - page 1782

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.1 Introduced the loopguard and rootguard options on the S4810. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series TeraScale, C-Series, and S-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the shutdown-on-violation option. ...

  • Dell 9.8(0.0) - page 1783

    54 System Time and Date The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, refer to the “Network Time Protocol” section of the Ma ...

  • Dell 9.8(0.0) - page 1784

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information You can change the order of the month and day parameters to enter the time and date as time day month year. You cannot delete the softwa ...

  • Dell 9.8(0.0) - page 1785

    start-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter ...

  • Dell 9.8(0.0) - page 1786

    clock summer-time recurring Set the software clock to convert to daylight saving time on a specific day each year. Z9500 Syntax clock summer-time time-zone recurring [ start-week start-day start-month start-time end-week end-day end-month end-time [ offset ]] To delete a daylight saving time zone configuration, use the no clock summer- time command ...

  • Dell 9.8(0.0) - page 1787

    end-month Enter the name of one of the 12 months in English. end-time Enter the time in hours:minutes:seconds. For the hour variable, use the 24-hour format; example, 17:15:00 is 5:15 pm. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to 1440. The default is 60 minutes . Defaults Not configur ...

  • Dell 9.8(0.0) - page 1788

    clock timezone Configure a timezone for the switch. Z9500 Syntax clock timezone timezone-name offset To delete a timezone configuration, use the no clock timezone command. Parameters timezone- name Enter the name of the timezone. You cannot use spaces. offset Enter one of the following: • a number from 1 to 23 as the number of hours in addition t ...

  • Dell 9.8(0.0) - page 1789

    debug ntp Display network time protocol (NTP) transactions and protocol messages for troubleshooting. Z9500 Syntax debug ntp {adjust | all | authentication | events | loopfilter | packets | select | sync} To disable debugging of NTP transactions, use the no debug ntp {adjust | all | authentication | events | loopfilter | packets | select | sync} co ...

  • Dell 9.8(0.0) - page 1790

    Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp authenticate Enable authentication of NTP traffic between the switch and the NTP time serving hosts. Z9500 Syntax ntp authenticate To disable NTP authentication, use the no ntp authentication command. Defaults Not enab ...

  • Dell 9.8(0.0) - page 1791

    ntp authentication-key Specify a key for authenticating the NTP server. Z9500 Syntax ntp authentication-key number md5 [0 | 7] key Parameters number Specify a number for the authentication key. The range is from 1 to 4294967295. This number must be the same as the number parameter configured in the ntp trusted-key command. md5 Specify that the auth ...

  • Dell 9.8(0.0) - page 1792

    The Dell Networking OS versions 8.2.1.0 and later use an encryption algorithm to store the authentication key that is different from previous versions; beginning in version 8.2.1.0, the system uses DES encryption to store the key in the startup- config when you enter the ntp authentication-key command. Therefore, if your system boots with a startup ...

  • Dell 9.8(0.0) - page 1793

    ntp disable Prevent an interface from receiving NTP packets. Syntax ntp disable To re-enable NTP on an interface, use the no ntp disable command. Defaults Disabled (that is, if you configure an NTP host, all interfaces receive NTP packets) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other p ...

  • Dell 9.8(0.0) - page 1794

    • 224.0.1.1 is configured if the interface address is IPv4 • ff05::101 is configured if the interface address is IPv6 Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The followi ...

  • Dell 9.8(0.0) - page 1795

    Version Description 9.6(0.0) Introduced on the S4810, S4820T, S5000, S6000, Z9000, and Z9500. ntp server Configure an NTP time-serving host. Z9500 Syntax ntp server { hostname | ipv4-address | ipv6-address } [key keyid ] [prefer] [version number ] Parameters ipv4-address | ipv6-address Enter an IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X). h ...

  • Dell 9.8(0.0) - page 1796

    Version Description 6.1.1.0 Introduced on the E-Series. Usage Information You can configure multiple time-serving hosts (up to 250). From these time- serving hosts, the system chooses one NTP host with which to synchronize. To determine which server was selected, use the show ntp associations command. Because many polls to NTP hosts can impact netw ...

  • Dell 9.8(0.0) - page 1797

    The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp trust ...

  • Dell 9.8(0.0) - page 1798

    Usage Information The number parameter in the ntp trusted-key command must be the same number as the number parameter in the ntp authentication-key command. If you change the ntp authentication-key command, you must also change the ntp trusted-key command. Related Commands ntp authentication-key — sets an authentication key for NTP. ntp authentic ...

  • Dell 9.8(0.0) - page 1799

    Example (Detail) Dell#show clock detail 12:18:10.691 UTC Wed Jan 7 2009 Time source is RTC hardware Summer time starts 02:00:00 UTC Sun Mar 8 2009 Summer time ends 02:00:00 ABC Sun Nov 1 2009 Dell# Related Commands clock summer-time recurring — displays the time and date from the switch hardware clock. show ntp associations Display the NTP master ...

  • Dell 9.8(0.0) - page 1800

    Field Description • * means synchronized to this peer. • # means almost synchronized to this peer. • + means the peer was selected for possible synchronization. • - means the peer is a candidate for selection. • ~ means the peer is statically configured. remote Displays the remote IP address of the NTP peer. ref clock Displays the IP addr ...

  • Dell 9.8(0.0) - page 1801

    Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0 ...

  • Dell 9.8(0.0) - page 1802

    Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show ntp status command shown in the Example below. Field Description “Clock is...” States whether or not ...

  • Dell 9.8(0.0) - page 1803

    55 Tunneling Tunneling is supported on Dell Networking OS. ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and specify the interface from which the tunnel borrows its address. Z9500 Syntax ip unnumbered {interface-type slot/port} To set the tunnel back to default logical address use the no ip unnumbered command. ...

  • Dell 9.8(0.0) - page 1804

    NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address. The tunnel interface status is not changed to operationally up until the logical IP address is identified from the address family. ipv6 unnumbered Configure a tunnel interface to operate without a unique IPv6 address and spe ...

  • Dell 9.8(0.0) - page 1805

    tunnel allow-remote Configure the remote IPv4 or IPv6 addresses whose tunneled packets are accepted for decapsulation. If you do not configure an allow-remote address, tunneled packets from all remote peer addresses are accepted. Z9500 Syntax tunnel allow-remote { ip-address | ipv6-address } [ mask ] To delete a configured allow-remote entry, enter ...

  • Dell 9.8(0.0) - page 1806

    tunnel destination Set a destination endpoint for the tunnel. Syntax tunnel destination { ip-address | ipv6–address } To delete a tunnel destination address, use the no tunnel destination { ip- address | ipv6–address } command. Parameters ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 add ...

  • Dell 9.8(0.0) - page 1807

    value Enter a value to set the DSCP value in the tunnel header. The range is from 0 to 63. The default value of 0 denotes mapping of original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/Traffic Class (IPv6) depending on the mode of tunnel. Defaults 0 (Mapped) Command Modes INTERFACE TUNNEL (conf-if-tu) Command History V ...

  • Dell 9.8(0.0) - page 1808

    Version Description 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. Usage Information This command is only valid for tunnel interfaces with an IPv6 outer header. tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit ...

  • Dell 9.8(0.0) - page 1809

    tunnel keepalive Configure the tunnel keepalive target, interval and attempts. Syntax tunnel keepalive { ip-address | ipv6-address }[interval { seconds }] [attempts { count | unlimited}] To disable the tunnel keepalive probes use the no tunnel keepalive command. Parameters ip-address ipv6 address Enter the IPv4 or IPv6 address of the peer to which ...

  • Dell 9.8(0.0) - page 1810

    into a keepalive down state that does not clear in a few seconds, then performing shutdown - no shutdown sequence on one end should bring both ends back to up. tunnel-mode Enable a tunnel interface. . Syntax tunnel mode { ipip | ipv6 | ipv6ip }[ decapsulate-any ] To disable an active tunnel interface, use the no tunnel mode command. Parameters ipip ...

  • Dell 9.8(0.0) - page 1811

    Configuration of IPv6 commands over decapsulate-any tunnel causes an error. tunnel source Set a source address for the tunnel. Syntax tunnel source { ip-address | ipv6–address | interface-type- number | anylocal} To delete the current tunnel source address, use the no tunnel source command. Parameters ip-address Enter the source IPv4 address in A ...

  • Dell 9.8(0.0) - page 1812

    allows the multipoint receive-only tunnel to decapsulate tunnel packets addressed to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the switch that is operationally Up . 1812 Tunneling ...

  • Dell 9.8(0.0) - page 1813

    56 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link. clear ufd-disable Re-enable one or more downstream interfaces on the switch/router that are in a UFD-Disabled Error state so that an interface can send ...

  • Dell 9.8(0.0) - page 1814

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 ...

  • Dell 9.8(0.0) - page 1815

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. Related Commands clear ufd-disable — re-enables downstream interfaces that are in a UFD-Disabled Error state. description Enter a text description of an uplink-state group. Z9500 Syntax description text Parameters text ...

  • Dell 9.8(0.0) - page 1816

    downstream Assign a port or port-channel to the uplink-state group as a downstream interface. Z9500 Syntax downstream interface To delete an uplink-state group, enter the no downstream interface command. Parameters interface Enter one of the following interface types: • 10-Gigabit Ethernet: tengigabitethernet { slot/ port | slot/port-range } • ...

  • Dell 9.8(0.0) - page 1817

    You can assign an interface to only one uplink-state group. Configure each interface assigned to an uplink-state group as either an upstream or downstream interface, but not both. You can assign individual member ports of a port channel to the group. An uplink- state group can contain either the member ports of a port channel or the port channel it ...

  • Dell 9.8(0.0) - page 1818

    • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. downstream disable links Configure the number of downstream links in the uplink-state group that are disabled if one upstream link in an uplink-state group goes down. Z9500 Syntax downstream disable links { number |all} To revert to the default sett ...

  • Dell 9.8(0.0) - page 1819

    Related Commands • downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. enable Enable uplink state group tracking for a specific UFD group. Z9500 Syntax enable To disable upstream-link tracking without ...

  • Dell 9.8(0.0) - page 1820

    show running-config uplink-state-group Display the current configuration of one or more uplink-state groups. Z9500 Syntax show running-config uplink-state-group [ group-id ] Parameters group-id Displays the current configuration of all uplink-state groups or a specified group. The valid group-id values are from 1 to 16. Defaults none Command Modes ...

  • Dell 9.8(0.0) - page 1821

    show uplink-state-group Display status information on a specified uplink-state group or all groups. Z9500 Syntax show uplink-state-group [ group-id ] [detail] Parameters group-id Displays status information on a specified uplink-state group or all groups. The valid group-id values are from 1 to 16. detail Displays additional status information on t ...

  • Dell 9.8(0.0) - page 1822

    1/5(Up) Te 1/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 0/0(Dwn) Te 0/3(Dwn) Te 0/5(Dwn) Downstream Interfaces : Te 1/2(Dis) Te 1/4(Dis) Te 1/11(Dis) Te 1/12(Dis) Te 1/13(Dis) Te 1/14(Dis) Te 1/15(Dis) Uplink State Group : 6 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 7 Sta ...

  • Dell 9.8(0.0) - page 1823

    Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. Usage Information After you enter the command, to assign upstream and downstream interfaces to the group, enter Uplink-State-Group Configuration mode. An uplink-state group is considered ...

  • Dell 9.8(0.0) - page 1824

    • 40-Gigabit Ethernet: fortyGigE { slot/port | slot/port-range } • Port channel: port-channel { 1-512 | port- channel-range } Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: tengigabitethernet 1/1-2,5,9,11-12 port- channel 1-3,5 . A comma i ...

  • Dell 9.8(0.0) - page 1825

    57 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. For more information about basic VLAN commands, refer to the Virtual LAN (VLAN) Commands section in the Layer 2 chapter. Important Points to ...

  • Dell 9.8(0.0) - page 1826

    member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Z9500 Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a ...

  • Dell 9.8(0.0) - page 1827

    peer-domain-link port-channel exclude-vlan Configure proxy-gateway LLDP, specify a port-channel and a VLAN or range of VLANs, and exclude a VLAN or a range of VLANs from proxy routing. Z9500 Syntax [no] peer-domain-link port-channel interface-identifier exclude-vlan vlan-range Parameters port-channel Configure the proxy-gateway interface port-chann ...

  • Dell 9.8(0.0) - page 1828

    vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network. Z9500 Syntax vlan-stack access To remove access port designation, use the no vlan-stack access command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platfo ...

  • Dell 9.8(0.0) - page 1829

    To disable the Stackable VLAN feature on a VLAN, use the no vlan-stack compatible command. Defaults Not configured. Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Net ...

  • Dell 9.8(0.0) - page 1830

    vlan-stack dot1p-mapping Map C-Tag dot1p values to a S-Tag dot1p value. You can separate the C-Tag values by commas and dashed ranges are permitted. Dynamic mode CoS overrides any Layer 2 QoS configuration in case of conflicts. Z9500 Syntax vlan-stack dot1p-mapping c-tag-dot1p values sp-tag-dot1p value Parameters c-tag-dot1p value Enter the keyword ...

  • Dell 9.8(0.0) - page 1831

    You may specify both bytes of the 2-byte S-Tag TPID. The range is from 0 to FFFF. The default is 9100 . Defaults 0x9100 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Del ...

  • Dell 9.8(0.0) - page 1832

    vlan-stack trunk Specify a Layer 2 port or port channel as a trunk port to the Stackable VLAN network. Z9500 Syntax vlan-stack trunk To remove a trunk port designation from the selected interface, use the no vlan- stack trunk command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command infor ...

  • Dell 9.8(0.0) - page 1833

    In Example 1, a VLAN-Stack trunk port is configured and then also made part of a single-tagged VLAN. In Example 2, the tag protocol identifier (TPID) is set to 8848. The “Te 2/10” port is configured to act as a VLAN-Stack access port, while the “Te 1/0” port acts as a VLAN-Stack trunk port, switching stackable VLAN traffic for VLAN 10, whil ...

  • Dell 9.8(0.0) - page 1834

    Dell(conf-if-te-1/0)#vlan-stack trunk Dell(conf-if-te-1/0)#exit Dell(config)#interface vlan 10 Dell(conf-if-vlan)#vlan-stack compatible Dell(conf-if-vlan)#member Te 0/0, Te 1/0, Te 2/10 Dell(conf-if-vlan)#exit Dell(config)#interface vlan 30 Dell(conf-if-vlan)#untagged TenGi 1/0 Dell(conf-if-vlan)#exit Dell(config)# Dell(config)#interface vlan 40 De ...

  • Dell 9.8(0.0) - page 1835

    untagged port-channel Specify un-tagged VLAN ports. Z9500 Syntax untagged port-channel port-channel-number To remove un-tagged VLAN ports, use the no untagged port-channel port- channel-number command. Parameters port-channel- number Enter the port-channel number. The range is from 1 to 512. Defaults Not configured. Command Modes INTERFACE Command ...

  • Dell 9.8(0.0) - page 1836

    58 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist on the same router at the same time. ip vrf Creates a customer VRF. Syntax ip vrf { vrf-name | management} [ vrf_id ] To delete a customer VRF, use the no ip vrf { vrf-name | management } [ vrf_id ] command. Paramete ...

  • Dell 9.8(0.0) - page 1837

    creating a management VRF. For other types of VRFs, VRF ID is an optional parameter. All values in the valid range that are not already taken are allowed. ip http vrf Configures an HTTP client with a VRF that is used to connect to the HTTP server. Z9500 Syntax ip http vrf {management | vrf-name } To undo the HTTP client configuration, use the ip ht ...

  • Dell 9.8(0.0) - page 1838

    To delete the descriptive name for a customer VRF, use the no description string command. Parameters string Enter a descriptive name for the VRF. Defaults None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide ...

  • Dell 9.8(0.0) - page 1839

    Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. Usage Information Use this command to attach an interface to a configured VRF. You can attach an interface to either a non-default VRF or a management VRF. To assign a port-back to a default VRF, remove VRF association from the interfa ...

  • Dell 9.8(0.0) - page 1840

    Parameters route-export Enter the keyword to leak or share routes between VRFs. tag Enter a tag (export route target) to expose routes to other VRFs. This tag acts as an identifier for exported routes. You can use this identifier while importing these routes into another non-default VRF. route-map- name (Optional) Enter the name of the route-map to ...

  • Dell 9.8(0.0) - page 1841

    ip route-import Imports IPv4 routes that are leaked by another VRF using the tag specified by that VRF during export of these routes. Syntax ip route-import tag [ route-map —name] Parameters route-import Enter the keyword route-import to import routes into the VRF. tag Enter a tag (ASN number) to specify an import route target for importing route ...

  • Dell 9.8(0.0) - page 1842

    ipv6 route-export Enables route leaking between VRFs. Exports or shares IPv6 routes corresponding to one VRF with other non-default VRFs. Syntax ipv6 route-export tag [ route-map-name ] Parameters route-export Enter the keyword route-export to leak or share routes between VRFs. tag Enter a tag (ASN number) as the export route target to expose route ...

  • Dell 9.8(0.0) - page 1843

    filtering options to match BGP, the BGP route is not leaked as that route is not active in the Source VRF. Related Commands ipv6 route-import – imports IPv6 routes from another VRF. ipv6 route-import Imports IPv6 routes that are leaked by another VRF using the tag specified by that VRF during export of these routes. Syntax ipv6 route-import tag [ ...

  • Dell 9.8(0.0) - page 1844

    The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. Related Commands ipv6 route-export – exports IPv6 routes to another VRF. match source-protocol Enables you to specify matching criteria while exporting or importing routes. Syntax matc ...

  • Dell 9.8(0.0) - page 1845

    Related Commands ipv6 route-import – imports IPv6 routes from another VRF. redistribute Redistributes leaked or exported routes corresponding to specific protocols. Syntax redistribute {imported-bgp | import-ospf | import-isis} Parameters imported-bgp Enter the keyword imported-bgp to redistribute leaked routes that are learnt using the BGP proto ...

  • Dell 9.8(0.0) - page 1846

    Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduce ...

  • Dell 9.8(0.0) - page 1847

    Command Modes CONFIGURATION-VRF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OSCommand Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. ...

  • Dell 9.8(0.0) - page 1848

    Ma 0/0, Ma 1/0, Ma 2/0, Ma 3/0, Ma 4/0, Ma 5/0, Ma 6/0, Ma 7/0, Ma 8/0, Ma 9/0, Ma 10/0, Ma 11/0, Nu 0, Vl 1 test1 1 Te 0/14,16-17 test2 2 Te 0/15 management 64 FTOS#show ip vrf test1 VRF-Name VRF-ID Interfaces test1 1 Te 0/14,16-17 show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax show run vrf vrf- ...

  • Dell 9.8(0.0) - page 1849

    Example Dell#show run vrf test3 ! ip vrf test3 description "Banking Customer Chennai" Related Commands Virtual Routing and Forwarding (VRF) 1849 ...

  • Dell 9.8(0.0) - page 1850

    59 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free top ...

  • Dell 9.8(0.0) - page 1851

    ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format. interval seconds Enter the keyword interval to specify the time interval to send hello messages. The range is from 1 to 5 seconds. The default is 1 second. Defaults 1 second Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information abo ...

  • Dell 9.8(0.0) - page 1852

    ndp Clear the VLT statistics for NDP. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced o ...

  • Dell 9.8(0.0) - page 1853

    Defaults Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S ...

  • Dell 9.8(0.0) - page 1854

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S4820T, S4810, S6000, S5000, Z9000, S6000–ON and ...

  • Dell 9.8(0.0) - page 1855

    Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. Usage Information LACP on the VLT ports (on a VLT switch or access device), which are members of the virtual link trunk, is not brought up until ...

  • Dell 9.8(0.0) - page 1856

    Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON ...

  • Dell 9.8(0.0) - page 1857

    Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan parameter. 8.3.8.0 Introduced on the S4810. Usage Information To configure ...

  • Dell 9.8(0.0) - page 1858

    peer-routing-timeout Configure the delay after which peer routing is disabled when the peer is unavailable. This command is applicable for both IPV6/IPV4. If not configured, peer-routing will not be disabled at all even though the peer is unavailable. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout co ...

  • Dell 9.8(0.0) - page 1859

    Default 32768 Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9. ...

  • Dell 9.8(0.0) - page 1860

    Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell Networking OS version number. VLT version numbers are begin with odd numbers such as 3 or 5 ...

  • Dell 9.8(0.0) - page 1861

    Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Example Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------- Destination: 10.11.200.18 Peer HeartBeat status: Up HeartBeat Timer Interval: 1 Hear ...

  • Dell 9.8(0.0) - page 1862

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information If you do not add a parameter such as arp or mac , the output displays all of the counters. Example Dell# ...

  • Dell 9.8(0.0) - page 1863

    show vlt detail Displays detailed status information about VLT domains currently configured on the switch. Syntax show vlt detail Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The follo ...

  • Dell 9.8(0.0) - page 1864

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. Example Dell#show vlt inconsistency ip mroute Spanned Multicast ...

  • Dell 9.8(0.0) - page 1865

    Example Dell#show vlt mismatch Domain ------- Parameters Local Peer ---------- ----- ----- Unit-ID 0 1 Vlan-config ------------ Vlan-ID Local Mode Peer Mode ------- ---------- --------- 100 -- L3 Vlan IPV4 Multicast Status -------------------------- Vlan-ID Local Status Peer Status -------- ------------ ----------- 4094 Active Inactive Dell# Exampl ...

  • Dell 9.8(0.0) - page 1866

    --------- -------- ----------- ---------- 128 128 4094 100 Dell# show vlt private-vlan Display the private VLAN (PVLAN) associated with the VLT LAG for VLT peer nodes. Syntax show vlt private-vlan Command Modes EXEC Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the ...

  • Dell 9.8(0.0) - page 1867

    show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the r ...

  • Dell 9.8(0.0) - page 1868

    show vlt statistics Displays statistics on VLT operations. Syntax show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Display the VLT statistics for the domain. multicast Display the VLT statistics for multicast. mac Display the VLT statistics for the MAC address. arp Display the VLT statistics for ARP. igmp-sn ...

  • Dell 9.8(0.0) - page 1869

    HeartBeat Messages Sent: 930 HeartBeat Messages Received: 909 ICL Hello's Sent: 927 ICL Hello's Received: 910 Domain Mismatch Errors: 0 Version Mismatch Errors: 0 Config Mismatch Errors: 0 VLT MAC Statistics ---------------- L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 ...

  • Dell 9.8(0.0) - page 1870

    show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS C ...

  • Dell 9.8(0.0) - page 1871

    Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced ...

  • Dell 9.8(0.0) - page 1872

    Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Informatio ...

  • Dell 9.8(0.0) - page 1873

    Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information The VLT domain ID must be the same between the two VLT devices. If th ...

  • Dell 9.8(0.0) - page 1874

    Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 1874 Virtual Link Trunking (VLT) ...

  • Dell 9.8(0.0) - page 1875

    60 VLT Proxy Gateway You can configure a proxy gateway in VLT domains. A proxy gateway enables you to locally route the packets that are destined to a L3 endpoint in another VLT domain. proxy-gateway lldp Configure the LLDP proxy gateway Z9500 Syntax proxy-gateway lldp Command Modes VLT DOMAIN Command History Version Description 9.5(0.1) Introduced ...

  • Dell 9.8(0.0) - page 1876

    Example Dell(conf)#vlt-domain 1 Dell(conf-vlt-domain#proxy-gateway lldp proxy-gateway static Configure the VLT static proxy gateway Z9500 Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Inform ...

  • Dell 9.8(0.0) - page 1877

    mac-address Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn format. vlan-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination. For example: Comma-separated: 3, 4, 6 Range: 5-10 Combination: 3, 4, 5-10, 8 Command Modes VLT DOMAIN PROXY GW STATIC Command History Version Descrip ...

  • Dell 9.8(0.0) - page 1878

    vlan-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination. For example: Comma-separated: 3, 4, 6 Range: 5-10 Combination: 3, 4, 5-10, 8 Command Modes VLT DOMAIN PROXY GW LLDP Command History Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, ...

  • Dell 9.8(0.0) - page 1879

    Version Description 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Information In a square VLT topology with only one link connecting remote peers, a node must stop sending its VLT peer MAC address ("vlt-peer-mac transmit" enabled) when the VLT peer is down. If you configure this time out interval, it will k ...

  • Dell 9.8(0.0) - page 1880

    show vlt-proxy-gateway Display the VLT proxy gateway configuration. Z9500 Syntax show vlt-proxy-gateway info {lldp | static} Parameters lldp Display details about the LLDP VLT proxy gateway configuration static Display details about the static VLT proxy gateway configuration Command Modes EXEC EXEC Privilege EXEC Privilege Command History Version D ...

  • Dell 9.8(0.0) - page 1881

    ----- ----------- ------------ Po 55 00:01:e8:8a:e8:f7 3,7-8 << Macs learnt via port-channel 55 Po 55 00:01:e8:8b:1c:c0 3,7-8 VLT Proxy Gateway 1881 ...

  • Dell 9.8(0.0) - page 1882

    61 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on Dell Networking OS. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Z9500 Syntax advertise-interval { seconds | centisecs centis ...

  • Dell 9.8(0.0) - page 1883

    Version Description 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 ...

  • Dell 9.8(0.0) - page 1884

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1885

    Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. debug vrrp Allows you to enable debugging of VRRP. Z9 ...

  • Dell 9.8(0.0) - page 1886

    interface Enter the keyword interface to enable debugging of interface state changes.. ipv6 Enter the keyword ipv6 to enable debugging for IPv6. packets Enter the keyword packets to enable debugging of VRRP control packets. state Enter the keyword state to enable debugging of VRRP state changes. timer Enter the keyword timer to enable debugging of ...

  • Dell 9.8(0.0) - page 1887

    Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on th ...

  • Dell 9.8(0.0) - page 1888

    Usage Information To enable VRRP traffic, assign an IP address to the VRRP group using the virtual-address command and enter no disable . Related Commands virtual-address — specifies the IP address of the virtual router. hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router. By delaying the initialization of the ...

  • Dell 9.8(0.0) - page 1889

    Usage Information If a switch is a MASTER and you change the hold timer, disable and re-enable VRRP for the new hold timer value to take effect. Related Commands disable — disables a VRRP group. preempt To preempt or become the MASTER router, permit a BACKUP router with a higher priority value. Z9500 Syntax preempt To prohibit preemption, use the ...

  • Dell 9.8(0.0) - page 1890

    Parameters priority Enter a number as the priority. Enter 255 only if the router’s virtual address is the same as the interface’s primary IP address (that is, the router is the OWNER). The range is from 1 to 255. The default is 100 . Defaults 100 Command Modes VRRP Command History This guide is platform-specific. For command information about o ...

  • Dell 9.8(0.0) - page 1891

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 ...

  • Dell 9.8(0.0) - page 1892

    ipv6 (OPTIONAL) Enter the keyword ipv6 to view only VRRP IPv6 groups. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for ...

  • Dell 9.8(0.0) - page 1893

    Item Description • NA/IF (the interface is not available). • MASTER (the interface associated with the MASTER router). • BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router. Virtual addr(s) Displays the virtual IP addresses of the VRRP routers associated with the interface. Exampl ...

  • Dell 9.8(0.0) - page 1894

    Item Description • Adv sent displays the number of VRRP advertisements sent on the interface. • Gratuitous ARP sent displays the number of gratuitous ARPs sent. Virtual MAC address Displays the virtual MAC address of the VRRP group. Virtual IP address Displays the virtual IP address of the VRRP router to which the interface is connected. Authen ...

  • Dell 9.8(0.0) - page 1895

    version Set VRRP protocol version for IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters 2 Enter the 2 parameter to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the 2 parameter to specify VRRP version 3 as defined in RFC 5798, Virtual Route ...

  • Dell 9.8(0.0) - page 1896

    Dell(conf-if-te-0/0-vrid-100)#version 3 virtual-address Configure up to 12 IP addresses of virtual routers in the VRRP group. To start sending VRRP packets, set at least one virtual address for the VRRP group. Z9500 Syntax virtual-address ip-address1 [ ... ip-address12 ] To delete one or more virtual IP addresses, use the no virtual-address ip- add ...

  • Dell 9.8(0.0) - page 1897

    Usage Information The VRRP group only becomes active and sends VRRP packets when a virtual IP address is configured. When you delete the virtual address, the VRRP group stops sending VRRP packets. A system message appears after you enter or delete the virtual-address command. To guarantee that a VRRP group becomes MASTER, configure the VRRP group? ...

  • Dell 9.8(0.0) - page 1898

    • When an interface comes up, whether as part of a system reload or an interface reload, the system waits 300 seconds (5 minutes) to bring up VRRP on that interface. Related Command vrrp delay reload — sets the delay time for VRRP initialization after a system reboot. vrrp delay reload Set the delay time for VRRP initialization after a system r ...

  • Dell 9.8(0.0) - page 1899

    Related Command vrrp delay minimum — sets the delay time for VRRP initialization after a line card reboot. vrrp-group Assign a VRRP ID to an interface. You can configure up to 12 VRRP groups per interface. Z9500 Syntax vrrp-group vrrp-id Parameters vrrp-id Enter a number as the group ID. The range is from 1 to 255. Defaults Not configured. Comman ...

  • Dell 9.8(0.0) - page 1900

    IPv6 VRRP Commands The following are IPv6 VRRP commands. • clear counters vrrp ipv6 • debug vrrp ipv6 • show vrrp ipv6 • vrrp-ipv6-group The following commands apply to IPv4 and IPv6: • advertise-interval • description • disable • hold-time • preempt • priority • show config • virtual-address clear counters vrrp ipv6 Clear t ...

  • Dell 9.8(0.0) - page 1901

    Version Description 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series. Support was added for IPv6 VRRP groups in non-default VRF instances. 8.3.2.0 Introduced on the E-Series TeraScale. debug vrrp ipv6 Allows you to enable debugging of VRRP. Z9500 Syntax debug vrrp i ...

  • Dell 9.8(0.0) - page 1902

    Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2.(1.0) Introduced on the Z9500. 8.3.19.0 Intro ...

  • Dell 9.8(0.0) - page 1903

    • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. ...

  • Dell 9.8(0.0) - page 1904

    Line Beginning with Description • Bad pkts rcvd displays the number of invalid packets received on the interface. Virtual MAC address Displays the virtual MAC address of the VRRP group. Virtual IP address Displays the virtual IP address of the VRRP router to which the interface is connected. Tracking states... Displays information on the tracked ...

  • Dell 9.8(0.0) - page 1905

    Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version Description 9.2.(1.0) Introduced on the Z9500. 8.4.2.1 The range of valid VRID values on t ...

Manufacturer Dell Category Switch

Documents that we receive from a manufacturer of a Dell 9.8(0.0) can be divided into several groups. They are, among others:
- Dell technical drawings
- 9.8(0.0) manuals
- Dell product data sheets
- information booklets
- or energy labels Dell 9.8(0.0)
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dell 9.8(0.0).

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dell 9.8(0.0), service manual, brief instructions and user manuals Dell 9.8(0.0). Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dell 9.8(0.0).

Similar manuals

A complete manual for the device Dell 9.8(0.0), how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dell 9.8(0.0) by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dell 9.8(0.0).

A complete Dell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dell 9.8(0.0) - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dell 9.8(0.0), FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dell 9.8(0.0), that we can find in the current document
3. Tips how to use the basic functions of the device Dell 9.8(0.0) - which should help us in our first steps of using Dell 9.8(0.0)
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dell 9.8(0.0)
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dell 9.8(0.0) in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dell 9.8(0.0)?

Use the form below

If you did not solve your problem by using a manual Dell 9.8(0.0), ask a question using the form below. If a user had a similar problem with Dell 9.8(0.0) it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)