English dropdown-ico

Manual GarrettCom DS60s

39 pages 0.54 mb
Download

Go to site of 39

Summary
  • GarrettCom DS60s - page 1

    www Garre t t C om c om .. Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http ://www.GarrettCom .com email support@garrettc om.com Magnum DS50 / DS60s Dual Speed Hubs Plus Installation and User Guide www Garre t t C om c om .. ...

  • GarrettCom DS60s - page 2

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) i www Garre t t Com com .. Magnum ™ DS50 / DS60s Dual Speed Ethernet Hubs Plus Installation and User Guide Part #: 84-00055 (Rev C 10/01) Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Unde ...

  • GarrettCom DS60s - page 3

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) ii www Garre t t Com com .. Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc. 47823 Westinghouse Dr.. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http ://www.GarrettCom .com e ...

  • GarrettCom DS60s - page 4

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) iii www Garre t t Com com .. 1.0 SPECIFICATIONS ............................................................................................................. ............2 1.1 Technical Sp ecifications ............................................................................ ...

  • GarrettCom DS60s - page 5

    Magnum DS50 & DS60s Dual Speed Hubs Installation and User Guide (06/02) The Magnum Line ETHERNET CONNECTIVITY PRODUCTS "DESIGNED AND M ANUFACTURED IN THE US A" OVERVIEW GarrettCom offers the Magnum line of Et hernet LAN connectivity products with industry-standard functionality. Magnum products are available worldwide through OEMs, in ...

  • GarrettCom DS60s - page 6

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 1.0 SPECIFICATIONS 1.1 Technical Specifications Performance Port 1-5: Repeater Ports, with bridge between Data Rate: 10/100 Mbps (Dual-Speed) PDV (Path Delay Value): 80BT Port 6: Switched Port (DS60C only) 10/100Mbps (Dual-Speed) When set to “FF”: Data Rate: 100 Mbps Full D ...

  • GarrettCom DS60s - page 7

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Power Supply (Internal) AC AC Power connector: IEC-type, ma le recessed, rear of chassis Power Input Voltage: 100 to 240 VAC (auto-ranging) Power Input Frequency: 47-63 Hz Power Consumption: typical 6 watts, 10 watts m ax. Power Supply (Internal), Optional 24VDC and -48VDC -48V ...

  • GarrettCom DS60s - page 8

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 1.2 Ordering Information Magnum DS50 / DS60 Dual-speed Hubs Plus Models Magnum DS60C Six dual speed ports, five 10/100 Dual-speed shared “hub” ports plus one 10/100 switched port, with shielded RJ-45 connectors and front-mounte d LED’s. The port #6 switched port is a sepa ...

  • GarrettCom DS60s - page 9

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 2.0 INTRODUCTION 2.1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that y ou believe occurred during shipment or delivery. Inspect the contents of this package for any sign ...

  • GarrettCom DS60s - page 10

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 2.2 Product Description The Magnum DS60C Dual-speed Hub Plus is an easy to in stall, cost-effective Dual- speed hub. It has five 10/100Mb repeater shar ed ports along with a 10/100 Mbps switched port that can be configured to provide “auto-nego tiating” or “Full fixed” ...

  • GarrettCom DS60s - page 11

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) DS60s are “plug and play” units enclosed in a lightweight, compact, rugged metal enclosure suitable for office, lab and industrial sites. Th e DS50 / DS60s are available for horizontal or vertical mounting (see Section 3.1). 2.2.1 Magnum DS60F Dual-speed Hubs Plus, with Fib ...

  • GarrettCom DS60s - page 12

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 2.2.2 Fiber port, SC Connector for Model DS60F SC type (single-mode or multi-mod e) The Fast Ethernet fiber switched port on the Magnum DS60F is set to operate at fixed 100Mb speed for guaranteed high performance. The DS60F’s fiber port is factory-built and available either a ...

  • GarrettCom DS60s - page 13

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) five shared 10/100Mb RJ-45 ports and one “10/ 100Mb switched RJ-45 port. There is an up-link (UPLINK) switch for Port 1. There is a ma nual switch “FF-A” underneath the switched port #6 that controls and provides “full-fixed” and “Aut o-negotiation” capability to ...

  • GarrettCom DS60s - page 14

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 10 www Garre t t Com com .. Magnum DS50 Dual-speed Hubs The Magnum DS50 has a power (PWR) and collision (COL) LED’s and 10 and 100 LED’s for the unit. It also has link (LINK) and receive (RX) activity LED’s for each of the five shared ports. Rubber feet on th e bottom pro ...

  • GarrettCom DS60s - page 15

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) device or node indicates that it is capable of 100Mbps speed, then operation on that port will be at 100Mbps. If the connected device does not pos itively indicate that it is capable of 100Mbps speed, then the operation on that DS50 / DS60 por t will be at 10Mbps. Of course, th ...

  • GarrettCom DS60s - page 16

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) The up-link operates the same, whether Port # 1 is connected to eith er a 100Mbps or 10Mbps device. When the up-link port is used to cascad e two DS50 / DS60 hubs, the auto-sensing feature of the DS50 / DS60 will cause the connecting link to operate at 100Mbps speed. 2.3 Frame ...

  • GarrettCom DS60s - page 17

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) processing resumes. This flow-control sequence occurs in a small frac tion of a second and is transparent to an observer. See Section 4.6 for additional details. Another feature implemented in Magnum DS60’sSwitched port is a collision-based flow-control mechanism (when operat ...

  • GarrettCom DS60s - page 18

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 2.4 Features and Benefits  Supports 10 or 100Mbps network connections on each of six RJ-45 ports A Magnum DS50 / DS60 Dual-Speed hub co mbines two logical hubs -- one at 10Mbps and one at 100Mbps -- in one physi cal box supporting two traffic domains. Each port can operate a ...

  • GarrettCom DS60s - page 19

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 2.5 Applications The Magnum Dual-speed H ub Plus is designed to provide dual speed (10/100Mbps) connectivity. Pictured below, a Magnum DS50 Dual-sp eed Hubs serves a small office with mixed speed requirements. Some users operate at 100Mbps, and some users and utility devices (s ...

  • GarrettCom DS60s - page 20

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) To add more 10/100Mb stations, another 10/ 100Mb workgroup can be added using a DS60C hub. By placing the Magnum DS60C Dual-speed H ub Plus in the middle, it acts as a bridge separating the 10Mb and the 100Mb traffic domai ns and provides each department with full bandwidth. Th ...

  • GarrettCom DS60s - page 21

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) In this example, a Magnum DS60F Dual-speed Hub serves in an Industrial place with servers and mixed-speed requirements, such as collec ting data or downloading data from servers or other sources. Some users operate at 100Mbps, and some users and utility devices (such as print s ...

  • GarrettCom DS60s - page 22

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 3.0 INSTALLATION This chapter provides instructions fo r installing the Magnum DS50 / DS60 Dual- speed Hub Plus. 3.1 Locating the Magnum DS50 / DS60 Dual-speed Hubs Plus The location of the Magnum DS50 / DS60 Du al-speed Hub Plus is dependent on the physical layout of the netwo ...

  • GarrettCom DS60s - page 23

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Each Magnum DS50 / DS60 Dual-speed Hub Plus is shipped with two mounting brackets (and screws), to allow the unit to be mounted in nearly any desired orientation or position. The brackets are attached to the unit’ s cas e with one of the metal screws for each bracket. It is r ...

  • GarrettCom DS60s - page 24

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Media IEEE Standard Connector Twisted Pair (CAT 3 or 5) 10BA SE-T RJ-45 Twisted Pair (CAT 5) 100BASE-TX RJ-45 Fiber (Multi-mode) 100BASE-FX SC Fiber (Single-mode) 100BASE-FX SC NOTE : It is recommended that high quality CAT. 5 cables (which work for both 10Mbps and 100Mbps) be ...

  • GarrettCom DS60s - page 25

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 5. The LINK LED for the fiber connector will illuminate when a proper connection has been established at both ends (and when power is ON in the unit). If LIN K is not lit after cable connection, the normal cause is improper cable polarity. Swap the fiber cables at the fiber con ...

  • GarrettCom DS60s - page 26

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 3.2.5 Connections to NICs which support Auto-Negotiation, RJ-45 ports The copper ports of Magnum DS50 / DS60s will function properly with NICs (Network Interface Cards) which support Auto-N egotiation, and the Fast Link Pulse (FLP) coding for the 100BASE-TX signaling system. Wh ...

  • GarrettCom DS60s - page 27

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Each Fast Ethernet device component also has an associated BT delay, which depends on the physical signaling system employed. Table 3.2b shows each Fast Ethernet device component and the associated BT delay. Note that there is only one DTE pair associated with any device-to-dev ...

  • GarrettCom DS60s - page 28

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) needs to know the total length of the Category 5 cable used to cascade th e hubs. The variable “X” is used to represent th e unknown maximum cascade length. PDV = X + ((111.2 + 111.2) + (92 + 92) + (100) + 0 ) BT < 512 BT 512 > (X + 506.4) BT X < (512 - 506.4) BT X ...

  • GarrettCom DS60s - page 29

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Table 3.2c: Maximum segment length s for common network co nfi g ur ati o ns Number of Hubs Repeater Hop Count Max. User Segment Lengths (m) Max. Inter- Repeater (Cascade) Length (m) Notes 1 1 100.0 N/A. All ports TX 2 2 100.0 5.0 All ports TX 2 2 92.0 20.0 All ports TX 2 2 79. ...

  • GarrettCom DS60s - page 30

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 4.0 OPERATION This chapter describes the function a nd operation of the Magnum DS50 / DS60. 4.1 Dual-Speed Functionality The repeater ports (port #1-5) of a Ma gnum DS50 / DS60 handles the two different traffic domains separately. The DS50 / DS60 pr ovides switched (bridged) co ...

  • GarrettCom DS60s - page 31

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) Packet Source Destination Address Table Filter/Forw ard Source Address Add ress Maintenance Action 10 Mbps Not in table Not in ta ble Add source to table Forward 10Mbps Not in table In table Add source to table Filter 10Mbps In table Not in table None Forward 10Mbps In table In ...

  • GarrettCom DS60s - page 32

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 4.2 Auto-negotiation and speed-sensing The first five RJ-45 ports independen tly support auto-negotiation for shared 10BASE-T and 100BASE-TX modes. Operation is according to the IEEE 802.3u standard. When an RJ-45 cable connection is made and each time a LINK is enabled, auto-n ...

  • GarrettCom DS60s - page 33

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) will be forwarded to the appropriate port, and will not be sent to the other ports where it is not needed. Traffic needed for maintaining the ope ration of the network (such as occasional multi- cast packets) is forwarded to all ports. The Magnum DS60’s switched port operate ...

  • GarrettCom DS60s - page 34

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) After switching from Full fixed to auto-ne gotiation or vice versa, it is necessary that the unit be powered down and back up to rese t the internal buffers of the switch. Even though it is not always required, powering dow n and up will enable proper packet handling in all cas ...

  • GarrettCom DS60s - page 35

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 5.0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments. Both the installation and operation of a Magnum DS50 / DS60 Dual-speed Hub Plus are simple procedures (see Section 3.0, INSTALLATI ...

  • GarrettCom DS60s - page 36

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) 5.2 When Calling for Assistance Please be prepared to provide the following information. 1. A complete description of the problem, including the following points: a. The nature and duration of the problem; b. Situations when the problem occurs; c. The components involved in the ...

  • GarrettCom DS60s - page 37

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) GarrettCom reserves the right to charge for the testing of non-defective units under warranty. Testing and repair of produc t that is not under warranty will result in a customer (user) charge. 5.4 Shipping and Packaging Information Should y ou need to ship the unit back to Gar ...

  • GarrettCom DS60s - page 38

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) APPENDIX B : Optional 24VDC or -48VDC Power Supply B1.0 SPECIFICATIONS - FOR MAGNUM DS50 / DS60 DUAL-SPEED HUBS PLUS Power Supply (Inte rnal -48VDC Option) DC Power Connector: 3 terminals: ( -) , “GND”, (+) Input Voltage: -36 to -72 VDC Power Consumption: Model DS50 / DS60: ...

  • GarrettCom DS60s - page 39

    Magnum DS50 / DS60s Dual Speed Hubs Installation and User Guide (06/02) B4.0 INSTALLATION -36 to -70VDC _ + GND This section describes the installation of the 24VDC or -48VDC power source leads to the 24VDC or - 48VDC power terminal block on the Magnum DS50 / DS60. (see figure right). Figure B4.1: Optional Ter mi nal Block on Magnum DS50 / DS60 wit ...

Manufacturer GarrettCom Category Switch

Documents that we receive from a manufacturer of a GarrettCom DS60s can be divided into several groups. They are, among others:
- GarrettCom technical drawings
- DS60s manuals
- GarrettCom product data sheets
- information booklets
- or energy labels GarrettCom DS60s
All of them are important, but the most important information from the point of view of use of the device are in the user manual GarrettCom DS60s.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GarrettCom DS60s, service manual, brief instructions and user manuals GarrettCom DS60s. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GarrettCom DS60s.

Similar manuals

A complete manual for the device GarrettCom DS60s, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GarrettCom DS60s by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GarrettCom DS60s.

A complete GarrettCom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GarrettCom DS60s - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GarrettCom DS60s, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GarrettCom DS60s, that we can find in the current document
3. Tips how to use the basic functions of the device GarrettCom DS60s - which should help us in our first steps of using GarrettCom DS60s
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GarrettCom DS60s
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GarrettCom DS60s in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GarrettCom DS60s?

Use the form below

If you did not solve your problem by using a manual GarrettCom DS60s, ask a question using the form below. If a user had a similar problem with GarrettCom DS60s it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)