Manual Stovax PR0919

33 pages 1.57 mb
Download

Go to site of 33

Summary
  • Stovax PR0919 - page 1

    STUDIO B a l a n c e d F l u e Instructions for Use, Installation and Servicing For use in GB, IE (Great Britain and Eire) PR0919 Issue 5 (January 2008) IMPORTANT Do not attempt to burn rubbish in this appliance. This appliance must only be operated with the glass door secured firmly in position. The front casing of this appliance will become hot w ...

  • Stovax PR0919 - page 2

    2 COVERING THE FOLLOWING MODEL: STUDIO 1 BALANCED FLUE: STUDIO 2 BALANCED FLUE: 8700BFCHEC 8701BFCHEC P8700BFCHEC P8701BFCHEC PAGE APPLIANCE COMMISSIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Requirements Installation 14 SERVICING INSTRUCTIONS 22 Fault Finding 22 How to replace parts 24 Basic s ...

  • Stovax PR0919 - page 3

    3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test N/A 3. Spillage test N/A GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full 4. Gas rate m 3 /h 5. Does ventilation meet appliance requirements N/A A ...

  • Stovax PR0919 - page 4

    4 USER INSTRUCTIONS 1. GENERAL 1.1 A competent person must carry out installation and servicing. 1.2 In all correspondence, please quote the appliance type and serial number, which can be found on the data badge located on a plate under the access panel, see Diagram 2, Installation. 1.3 Do not place curtains above the fire: You must have 300mm (1? ...

  • Stovax PR0919 - page 5

    5 USER INSTRUCTIONS  DECREASINGTEMPERATURE  • Pressthe DOWNarrow onceto decreaseflame height  one stage  • Pressand holdthe DOWNarrow todecrease to  minimum At the lowest point the fire goes to ‘standby mode’ (only pilot lit) NOTE: While pressing a button a ...

  • Stovax PR0919 - page 6

    6 USER INSTRUCTIONS  • Pressthe ON-OFFbutton toturn theappliance off EMERGENCY SHUT OFF If the batteries fail during use of the fire, move the switch to theOFF (O) position,Diagram 3  (Thisswitch is setto beON duringnormal operationand mustremain ON) 3 AR1933 3 ...

  • Stovax PR0919 - page 7

    7 USER INSTRUCTIONS 5. ARRANGEMENT OF FUEL BED 5.1 If you need to replace pebbles or refill the tray, make sure the pebbles are flattened so they are level with the rim of the tray. TAKE CARE NOT TO SPILL PEBBLES INTO THE PILOT AREA ONLY PEBBLES SUPPLIED BY GAZCO CAN BE USED IN THIS FIRE 6. FLAME FAILURE DEVICE 6.1 This is a safety feature incorpor ...

  • Stovax PR0919 - page 8

    8 Model Gas CAT. Gas Type Working Pressure Aeration Injector Gas Rate m 3 /h Input kW (Gross) Country High Low Studio 1 BF 12H Natural G20 20mbar 16 x 23 400 0.600 6.3 3.0 GB, IE Studio 1 BF 13P Propane G31 37mbar 14 x 16 (1) 16 x 23 (1) 185 0.230 6.1 3.0 GB, IE Studio 2 BF 12H Natural G20 20nbar 14 X 16 600 0.800 8.4 4.3 GB, IE Studio 2 BF 13P Pro ...

  • Stovax PR0919 - page 9

    9 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the translated instructions and in some cases the appliance will require modification. Contact Gazco for further information. PACKING CHECKLIST Qt ...

  • Stovax PR0919 - page 10

    10 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION Steel Frame Dimensions Dimension Studio 1 Studio 2 A 1120 1350 B 675 675 C 646 846 D 320 320 E 177 177 F 237 237 G 25 25 Profil Frame Dimensions Dimension Studio 1 Studio 2 A 836 1036 B 510 510 C 740 940 D 414 414 E 48 48 F 48 48 G 12.5 12.5 Bauhaus Frame Dimensions Dimension Studio 1 Studio 2 A ...

  • Stovax PR0919 - page 11

    11 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS Note: This appliance must only be installed with the flue supplied. You must adhere to the following: 1.1 The flue must be sited in accordance with BS5440: Part 1 (latest edition). See Diagram 1. 1.2 Fit a guard to protect people from any terminal less than 2 metres above any access such as level groun ...

  • Stovax PR0919 - page 12

    12 STUDIO 1 BF 1A AR1671 STUDIO 2 BF 1A AR1971 Start of bend to centre line of horizontal flue 170mm. Centre line of vertical flue to end of bend 220mm. 2.1 TOP FLUE UP & OUT KIT STUDIO 1 BF (8534/8534AN) Vertical from the top of the appliance then horizontally out. (See Diagram 1A). The basic kit comprises: 1 x 200mm vertical length 1 x 500mm ...

  • Stovax PR0919 - page 13

    13 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1C AR1673 2.3 TOP FLUE VERTICAL KIT (8524/8524AN) Vertical from the top of the appliance (See Diagram 1C). A minimum vertical rise 3m (9’10") to a maximum 10m (32’10"). The basic kit comprises: 2 x 1m lengths 1 x 1m terminal length 1 x 52mm restrictor 1 x 47mm restrictor 1 x 60mm restrict ...

  • Stovax PR0919 - page 14

    14 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS/INSTALLATION 5. APPLIANCE LOCATION 5.1 Please note this appliance has been specifically designed for stud work applications. There are two methods of installation, see Installation Instructions 3.2 Frame, 3.3 Edge 5.2 Thisappliance must standon anon-combustible hearth/ platform ...

  • Stovax PR0919 - page 15

    15 INSTALLATION INSTRUCTIONS INSTALLATION 2 AR1869 access panel 2 AR1888 3. STUD WORK INSTALLATION 3.1 Combustible parts of the stud work must be kept beyond theminimum dimensions shownin Diagram4. Evenif the frameworkis protected bynon-combustible material,you must maintain these dimensions, Diagr ...

  • Stovax PR0919 - page 16

    16 INSTALLATION INSTRUCTIONS INSTALLATION  • Fitthesupplied topsupportbar intothe studworkat the correct height, Diagram 7, because no combustible material can be used above the fire 7 AR1904  • Attachthe 4frame fixingbrackets tothe fire,Diagram 8  • Fix ...

  • Stovax PR0919 - page 17

    17 INSTALLATION INSTRUCTIONS INSTALLATION 13 AR1905 3.3 STUD WORK INSTALLATION METHOD 2 (EDGE)  Forthis cool-wallEdge installation, theconvected heatof the fire is channelled into the chimney cavity and vented at the top.  Thereis an optionalStudio EdgeFixing Kitavailable for installing ...

  • Stovax PR0919 - page 18

    18 INSTALLATION INSTRUCTIONS INSTALLATION Studio 1 BF 17 Studio 2 BF Studio 1 & 2 BF AR1671, AR1971, AR1673 TAKE CARE WHEN MARKING OUT FOR THE FLUE AS IT IS DIFFICULT TO MOVE AFTER INSTALLATION. IF A RESTRICTOR IS REQUIRED FIT THIS BETWEEN THE SMALL OUTLET SPIGOT AND THE AIR DUCT SEE DIAGRAM 18. REFER TO TECHNICAL SPECIFICATIONS FOR RESTRICTO R ...

  • Stovax PR0919 - page 19

    19 INSTALLATION INSTRUCTIONS INSTALLATION 4.6 Onlythe horizontalterminal section canbe reducedin size. To find the length:  • Measurefrom theoutside ofthe wallto thestop onthe 90°  • Add 10 mm to the outlet end   • Measure fromthe edgeof ...

  • Stovax PR0919 - page 20

    20 INSTALLATION INSTRUCTIONS INSTALLATION  • Offerthe frameto thefoot ofthe opening  • Slidethe frameto theright tolocate theright hingepin 24 AR1865 5.4 • Manoeuvrethe frame uptowards theleft sideto locate the left hinge pin  • Sl ...

  • Stovax PR0919 - page 21

    21 INSTALLATION INSTRUCTIONS INSTALLATION  • Pressthe ON-OFFbutton tolight theappliance, (upto   30 seconds)  • Pressthe UPbutton toincrease theflame height.  • Pre ssthe DOW Nbutton to decreasethe flameheight.At the lowest point it ...

  • Stovax PR0919 - page 22

    22 INSTALLATION INSTRUCTIONS COMMISSIONING 7. COMMISSIONING 7.1 Complete the Commissioning Checklist at the front of this manual covering:  • Fluechecks  • Gaschecks  • Pebblelayout -flame picture For working pressure test, use the access panel at the gas connection ensuring the burner is in position. 7.2 I ...

  • Stovax PR0919 - page 23

    23 IGNITION FUNCTIONAL CHECK 1 PILOTWILL NOTLIGHT Ensurethere isno debrisaroundthe pilotassembly, (e.g. soot, etc.) which could short the spark, clean the area. Operatethe valve. Is there a spark? Consult User Instructions and retry. Check alignment of pilot burner head, change the ignition lead. See Replac ...

  • Stovax PR0919 - page 24

    24 PILOTWILL NOTSTAY LITORFIRE GOESOUT INUSE Ensurethere isno debrisaroundthe pilotassembly, (e.g. soot etc.) Check for fluff in the pilot aeration hole. See the Diagram in the Replacing Parts section. Problem is with the pipe work or fittings which lead to the fire. Correct and retry. Is the ...

  • Stovax PR0919 - page 25

    3.2 To completely remove the glass front:  • Removethe securingspring clipfrom thebottom-right of the window frame, Diagram 3 3 AR1862 3.3 Withthe window framein anupright position:  • Slidethe frameto theleft sothat itcomes offthe left ? ...

  • Stovax PR0919 - page 26

    26 SERVICING INSTRUCTIONS REPLACING PARTS 4. GLASS WINDOW 4.1 Remove the two clips and brackets from either side of the frame, Diagram 5 5 AR1864  • Liftthe glassclear fromthe lockbracket atthe topof the frame and slide out 5. BLACK ENAMELLED PANELS 5.1 Slide the side panels forward until clear of t ...

  • Stovax PR0919 - page 27

    27 9 AR1868  • Slidethe burnerto theright andout ofits location  • Refitin reverseorder  Whenrefilling the stonepebbles, fillto thelevel ofthe rim of the burner tray and flatten level. Ensure no stone pebbles fall into the pilot area. 7. MAIN CONTROL ASSEM ...

  • Stovax PR0919 - page 28

    28 SERVICING INSTRUCTIONS REPLACING PARTS 8. PILOT UNIT ASSEMBLY 8.1 The pilot assembly consists of four components which can be individually changed: 1. Pilot burner bracket 2. Pilot injector  3. Electrode 4. Thermocouple Before commencing work on the pilot the Main Control Assembly must be removed, see Section 7 above. 8.2 Pilot Burner B ...

  • Stovax PR0919 - page 29

    29 SERVICING INSTRUCTIONS REPLACING PARTS 10. GAS VALVE 10.1 To change the gas valve:  • Removethe controlassembly, Section7  • Releasethe gasinlet pipe,Diagram 18,Arrow A  • Removethe thermocouplefrom theinterrupter block  andrelease thesecond thermo ...

  • Stovax PR0919 - page 30

    30 SERVICING INSTRUCTIONS REPLACING PARTS 13. MAIN INJECTOR 13.1 To change the main injector:  • Undothe injectorfee pipe  • Undothe locknut fromthe injector  • Replacewith thecorrect sizeinjector 14. PRIMARY AERATION PLATE  NOTALL MODELS HAVEAERATION PLATES.R ...

  • Stovax PR0919 - page 31

    31 SERVICING INSTRUCTIONS REPLACING PARTS 15. SHORT SPARES LIST STUDIO 1 BF STUDIO 2 BF COMPONENT NG LPG NG LPG PILOTINJECTOR PI0069 PI0070 PI0069 PI0070 MAININJECTOR IN0007 IN0040 IN0005 IN0041 BURNER ASSEMBLY GZ5983 GZ6363 GZ6417 GZ6418 AERATION PLATE G20- N/A G30 -N/A G20- GZ2025 G31 -GZ2025 G25- G ...

  • Stovax PR0919 - page 32

    32 SERVICE RECORDS 1ST SERVICE Date of Service:........................................................................... Next Service Due:....................................................................... Signed:........................................................................................ Dealer'sStamp/CORGIRegistration ...

  • Stovax PR0919 - page 33

    Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group ...

Manufacturer Stovax Category Stove

Documents that we receive from a manufacturer of a Stovax PR0919 can be divided into several groups. They are, among others:
- Stovax technical drawings
- PR0919 manuals
- Stovax product data sheets
- information booklets
- or energy labels Stovax PR0919
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stovax PR0919.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stovax PR0919, service manual, brief instructions and user manuals Stovax PR0919. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stovax PR0919.

Similar manuals

A complete manual for the device Stovax PR0919, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stovax PR0919 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stovax PR0919.

A complete Stovax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stovax PR0919 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stovax PR0919, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stovax PR0919, that we can find in the current document
3. Tips how to use the basic functions of the device Stovax PR0919 - which should help us in our first steps of using Stovax PR0919
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stovax PR0919
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stovax PR0919 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stovax PR0919?

Use the form below

If you did not solve your problem by using a manual Stovax PR0919, ask a question using the form below. If a user had a similar problem with Stovax PR0919 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)