English dropdown-ico

Manual Raypak B-195

23 pages 0.52 mb
Download

Go to site of 23

Summary
  • Raypak B-195 - page 1

    CATALOG NO.: 3300.51 I Effective: 01-01-03 Replaces: 01-01-01 Model B-195 FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS *Do not try to light any appliance. *Do not touch any electrical switch; do not use any phone in your building. *Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. *If you c ...

  • Raypak B-195 - page 2

    CONTENTS PAGE DESCRIPTION 3 1. RECEIVING EQUIPMENT 3 2. GENERAL SPECIFICATIONS AND DIMENSIONS 4 3. INSTALLATION PROCEDURES 4 - Code Requirements 4 - Combustion/Ventilation Air 5 - Venting 8 - Gas Piping 8 - Water Piping 11 - Electrical Wiring 12 4. START-UP AND OPERATION 12 - Component Location 12 - Sequence of Operation 12 - START-UP Procedures. 1 ...

  • Raypak B-195 - page 3

    3 1. RECEIVING EQUIPMENT On receipt of your equipment it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the Bill of Lading when signing for equipment. Remove the heater from the carton and if it is damaged report the damage to the carrier immediately. Be sure ...

  • Raypak B-195 - page 4

    3. INSTALLATION PROCEDURES. CODE REQUIREMENTS Installation must be in accordance with local codes, or in the absence of local codes with the latest edition of the National Fuel Gas Code, ANSI Z223.1, the National Electrical Code, ANSI/NFPA 70. For Canada, CAN/ CGA B149.1 and .2, and CSA C22.2 No. 1. LEG INSTALLATION Four (4) legs are supplied loose ...

  • Raypak B-195 - page 5

    Measures must be taken to prevent the entry of corrosive chemical fumes to the combustion and ventilation air supply. Such chemicals include, but are not limited to, chlorinated and/or fluorinated hydrocarbons such as found in refrigerants, aerosol propellants, dry-cleaning fluids, degreasers, and paint removers. Other harmful elements may come fro ...

  • Raypak B-195 - page 6

    6 Fig. #8975.3 Applies only to exhaust hood over cooking equipment. ...

  • Raypak B-195 - page 7

    All horizontal runs of the vent pipe shall have a minimum rise of 1/4" per foot of length and should be supported at maximum intervals of 5 feet (for Canada, 3 feet) and at each point where an elbow is used. For horizontal venting, the total length of 4-inch diameter pipe shall not exceed 30 feet with up to two 90° elbows and 1 termination ve ...

  • Raypak B-195 - page 8

    GAS PIPING The gas inlet pipe size is 1/2" NPT to the gas valve. Provide an adequate size gas supply line. The line should not be smaller than 1/2" NPT according to the chart below. MAXIMUM EQUIVALENT PIPE LENGTH (FEET) Pipe Size Gas 1/2" 3/4" 1" Natural 5 30 100 Propane 70 180 Gas piping must have a sediment trap ahead of ...

  • Raypak B-195 - page 9

    9 A drain valve is provided in the tank for draining water during servicing. The temperature and pressure relief valve is easily accessible through the front. A nipple is provided (shipped loose with the heater) for installation in the T & P relief valve. A drain line must be connected to the nipple and run to a safe place of disposal. WARNING: ...

  • Raypak B-195 - page 10

    ELECTRICAL The electrical power supply requirement for the heater is 120 volts, 60 Hz, 5.0 amps or less . Field wiring connections and electrical grounding must comply with the local codes, or in the absence of local codes, with the latest edition of the National Electrical Code, ANSI/NFPA 70. NOTE: Polarity must be observed for the heater to opera ...

  • Raypak B-195 - page 11

    11 LADDER DIAGRAM CONNECTION DIAGRAM DANGER: SHOCK HAZARD Turn off electrical power to boost heater before servicing any component in the heater to prevent equipment damage or personal injury. NOTE: If it is necessary to replace any of the original wiring, it must be replaced with 105°C rated wire or its equivalent. ...

  • Raypak B-195 - page 12

    SEQUENCE OF OPERATION The booster heater is designed to maintain a tempera- ture of 180 deg. F (82.2 Deg. C) of 490 GPH water required for the rinse cycle of a commercial dish- washer. An inlet temperature of 140 Deg. F (60 Deg. C) will produce optimum results. Provided the necessary power, water, gas and vent connections are completed, the unit is ...

  • Raypak B-195 - page 13

    SECTION 3. LIGHTING THE HEATER Safety lighting and other performance criteria were met for the burner assembly and control assembly when the heater was tested for design certification under the ANSI Z21.10.3 Standard WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or ...

  • Raypak B-195 - page 14

    SECTION 4. TESTING THE IGNITION SAFETY SHUT-OFF The ignition system safety shut-off must be tested by conducting the following method of tests: a) With the system power off, manually shut off the gas supply. b) Turn power back on, observe the igniter start to heat up and glow bright orange. c) After about four (4) seconds, the gas valve is energize ...

  • Raypak B-195 - page 15

    5. Limit Control Module a) Shut-off electrical power to the heater. b) Remove control cover screws and open con- trol compartment. c) Disconnect wiring connections to the board. d) Carefully pull out the control board from the nylon pin supports. e) Reverse above procedure to reinstall. 6. Sensor Probe Replacement a) Shut off electrical power to th ...

  • Raypak B-195 - page 16

    5. SERVICING UNIT TROUBLE SHOOTING GUIDE PROBLEM 1. On-Off switch energized. Unit does not operate. 2. Pump/Blower NOT running. 3. Unit energized, pump and blower running, but burner is NOT on. POSSIBLE CAUSE 1a. No power to heater 1b. Defective transformer 2a. Loose wire(s) 2b. Defective pump 2c. Defective blower. 3a . Limit control (operating lim ...

  • Raypak B-195 - page 17

    Continuation TROUBLE SHOOTING GUIDE 3d. Excessive negative pressure exerted by the exhaust system on the vent will prevent N.O. combustion air/vent switch from closing. Provide means to relieve pressure and close the N.O. switch. If combustion air/vent switch will not close, replace switch. 3e. Disconnect igniter leads from ignition module. Make su ...

  • Raypak B-195 - page 18

    18 6. REPLACEMENT PARTS LIST NOTE: To supply the correct part it is important that you state the model number, serial number and type of gas when applicable. Any part returned for replacement under standard company warranties must be properly tagged with RAYPAK return parts tag, completely filled in with the heater Serial Number, Model Number etc., ...

  • Raypak B-195 - page 19

    19 ...

  • Raypak B-195 - page 20

    20 ...

  • Raypak B-195 - page 21

    21 ...

  • Raypak B-195 - page 22

    LIMITED PARTS WARRANTY COMMERCIAL BOOSTER HEATER SCOPE: Raypak, Inc. ("Raypak") warrants to the owner that all parts of this booster heater, excluding controls and pump, will be free from failure under normal use and service for the specified warranty periods and subject to the conditions set forth in this Warranty. The Warranty is effect ...

  • Raypak B-195 - page 23

    Raypak, Inc. , 2151 Eastman Avenue, Westlake Village, CA 93030 (805) 278-5300 FAX (800) 872-9725 Raypak Canada Limited , 2805 Slough St., Mississauga, Ontario, Canada L4T 1G2 (416) 677-7999 FAX (416) 677-8036 Litho in U.S.A. www .raypak.com ...

Manufacturer Raypak Category Water Heater

Documents that we receive from a manufacturer of a Raypak B-195 can be divided into several groups. They are, among others:
- Raypak technical drawings
- B-195 manuals
- Raypak product data sheets
- information booklets
- or energy labels Raypak B-195
All of them are important, but the most important information from the point of view of use of the device are in the user manual Raypak B-195.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Raypak B-195, service manual, brief instructions and user manuals Raypak B-195. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Raypak B-195.

Similar manuals

A complete manual for the device Raypak B-195, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Raypak B-195 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Raypak B-195.

A complete Raypak manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Raypak B-195 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Raypak B-195, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Raypak B-195, that we can find in the current document
3. Tips how to use the basic functions of the device Raypak B-195 - which should help us in our first steps of using Raypak B-195
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Raypak B-195
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Raypak B-195 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Raypak B-195?

Use the form below

If you did not solve your problem by using a manual Raypak B-195, ask a question using the form below. If a user had a similar problem with Raypak B-195 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)