English dropdown-ico

Manual Grizzly H6145

20 pages 1.19 mb
Download

Go to site of 20

Summary
  • Grizzly H6145 - page 1

    COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL6905 PRINTED IN CHINA 2 8 ° C L I P P E D H E A D F R A M I N G N A I L E R MODEL H6145 INSTRUCTION MANUAL ...

  • Grizzly H6145 - page 2

    For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. R ...

  • Grizzly H6145 - page 3

    H6145 28° Clipped Head Framing Nailer -1 - 6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PER- SONNEL TO OPERATE MACHIN- ERY. Make sure operation instruc- tions are safe and clearly under- stood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visi- tors a safe distance from the work area. 8 . MAKE WORKSHOP CHILD PROOF. Use padlocks, mast ...

  • Grizzly H6145 - page 4

    H6145 28° Clipped Head Framing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source . Only use fil- tered ...

  • Grizzly H6145 - page 5

    H6145 28° Clipped Head Framing Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your ...

  • Grizzly H6145 - page 6

    H6145 28° Clipped Head Framing Nailer -4 - INTRODUCTION If you have any c omme nts reg ard ing th is man ual, pl ease w rite to u s at the follow ing add ress : Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we s tand b ehin d ou r too ls. If you have any ser vi ce que stio ns o ...

  • Grizzly H6145 - page 7

    H6145 28° Clipped Head Framing Nailer -5 - SET UP Figure 1. Model H6145 inventory. B C D G Unpacki ng Y our Mo del H 61 4 5 lef t our ware hou se i n a c arefu lly pac ked b ox. If you d isc over th e n ail er is d amag ed af te r yo u have sig ned for del iver y , ple ase i mme diat ely cal l Cu stom er Ser vice at ( 57 0 ) 54 6- 96 63 for advic ...

  • Grizzly H6145 - page 8

    H6145 28° Clipped Head Framing Nailer -6 - Compressed Air Sy stem The M ode l H 61 4 5 is des igne d t o b e o per- ated at 70-1 20 PS I us ing cle an, dr y , r egu - late d, c omp ress ed a ir . DO NOT exce ed th e max imum op er ati ng pre ssu re for your mod el . Befo re u sing your new na iler, reg ulate the air pr essu re on you r air co mpre ...

  • Grizzly H6145 - page 9

    H6145 28° Clipped Head Framing Nailer -7 - Safety Y ok e A safet y yoke me chan ism (b ump fi re) o n the nos e of the nai ler ac ts as a se con d- ar y safet y d evic e. W hen th e t rig ger i s pres sed , the nailer wil l not f ire un til t he safet y yoke m ech anis m i s de pres sed. Befo re you us e your nai ler for t he fir st tim e, che ck ...

  • Grizzly H6145 - page 10

    H6145 28° Clipped Head Framing Nailer -8 - OPERATIONS Loadin g Figure 3. Sliding pusher toward the catch lever pusher. When replacing nails in your Model H6145, follow these guidelines: Diameter: 7 ⁄ 64 "- 1 ⁄ 8 " Length: 2"-3 1 ⁄ 2 " Capacity: 100 Strip Angle: 28 ° NO TI CE : A nu mbe r of m anu fac tur ers' nai ls ...

  • Grizzly H6145 - page 11

    H6145 28° Clipped Head Framing Nailer -9 - Figure 6. Loosening cap screw for depth adjustment. The nose of the gun houses a depth adjust- ment mechanism for setting the nail depth. To adjust the dep th: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. If the nail is driven too far into the workpiece, loosen the cap screw on the safety nose with a 4mm ...

  • Grizzly H6145 - page 12

    H6145 28° Clipped Head Framing Nailer -10 - A jammed nail must be cleared before using the nailer again. The two places where a nail ca n get jammed are the maga- zine and the discharge area. To clear a jammed nail from the maga- zine: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2 . Pull back and lo ck th e maga zine push- er. 3. Remove the nail sti ...

  • Grizzly H6145 - page 13

    H6145 28° Clipped Head Framing Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u us e your na iler day i n an d day out , repa ir pisto ns are chea p ins uran ce agai nst wa sted do wn tim e and los t profi ts, in the event that a p isto n or pi ston sha ft bec ome s wo rn o ut. 5. The top of the piston should now be visible inside the cylinde ...

  • Grizzly H6145 - page 14

    H6145 28° Clipped Head Framing Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od s olven t to cl ean t he no se ass emb ly of the nail er . Always be s ure th at t he n ail er i s dr y bef ore us ing it agai n. Do not a llow du st, c hips , s and, etc . i nto the air co nnec tor s or i nto t he bo dy o f th e nai ler; th is may res ult ...

  • Grizzly H6145 - page 15

    H6145 28° Clipped Head Framing Nailer -13 - H6145 PARTS BREAKDOWN                                             ? ...

  • Grizzly H6145 - page 16

    H6145 28° Clipped Head Framing Nailer -14 - H6145 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6145001 SPCL CAP SCR M8-1.25 X 30 48 PW02M FLAT WASHER 5MM 2 PH6145002 AIR DEFLECTOR 49 PH6145049 ADJUSTING � NUT 3 PH6145003 RUBBER WASHER 50 PH6145050 SAFETY � YOKE 4 PH6145004 SPRING 51 PH6145051 SAFETY � NOSE 5 PH6145005 SPRING ...

  • Grizzly H6145 - page 17

    H6145 28° Clipped Head Framing Nailer -15 - 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use teflon tape 1. Replace damaged seals. 1. Tighten screws and fit - tings. 2. Clean nose. 3. Clean magazine and inspect/repair damage. 4. Check fitting, hose, c ...

  • Grizzly H6145 - page 18

    Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr ...

  • Grizzly H6145 - page 19

    Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6145 28° Clipped Head Framing Nailer Serial#_______________Order ...

  • Grizzly H6145 - page 20

    FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...

Manufacturer Grizzly Category Nail Gun

Documents that we receive from a manufacturer of a Grizzly H6145 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- H6145 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly H6145
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly H6145.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly H6145, service manual, brief instructions and user manuals Grizzly H6145. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly H6145.

Similar manuals

A complete manual for the device Grizzly H6145, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly H6145 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly H6145.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly H6145 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly H6145, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly H6145, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly H6145 - which should help us in our first steps of using Grizzly H6145
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly H6145
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly H6145 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly H6145?

Use the form below

If you did not solve your problem by using a manual Grizzly H6145, ask a question using the form below. If a user had a similar problem with Grizzly H6145 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)