English dropdown-ico

Manual Digicom Tintoretto

32 pages Not applicable
Download

Go to site of 32

Summary
  • Digicom Tintoretto - page 1

    TINTORETTO USER'S MANUAL Cod. 7D1109 rev . 1.0 02/98 ...

  • Digicom Tintoretto - page 2

    http://www .digicom.it ...

  • Digicom Tintoretto - page 3

    Index I INDEX PREF ACE III 1. GENERALITY 1.1 1.1. PRODUCT P ACKAGE CONTENTS 1.1 1.1.2. PRODUCT OPTION (UPON REQUEST) 1.1 1.2. PRODUCT FEA TURES 1.1 2. INST ALLA TION 2.1 2.1. HARDWARE INST ALLA TION 2.1 2.1.1. TINTORETTO EXTERNAL 2.1 2.1.2. TINTORETTO INTERNAL ISA BUS 2.1 2.1.3. INTORETTO PC-CARD PCMCIA 2.2 2.2. SOFTWARE INST ALLA TION 2.2 2.2.1. W ...

  • Digicom Tintoretto - page 4

    Preface III PREF ACE All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise, without the prior written permission of Digicom S.p.A.. The contents of this booklet may be modified without prior permission. Every possible care has been taken in ...

  • Digicom Tintoretto - page 5

    Generality 1.1 1. GENERALITY This operating manual describes the installation procedures and the main features of the Tintoretto ISDN modem family: Tintoretto external (PC or Macintosh), T intoretto internal ISA card (PC) and T intoretto PCMCIA (PC or Macintosh). See the details of the installation procedure of your enviromental in the installation ...

  • Digicom Tintoretto - page 6

    Installation 2.1 2. INST ALLA TION 2.1. HARDW ARE INSTALLA TION 2.1.1. TINTORETT O EXTERNAL See the following picture to connect your modem to the COM port of your PC and the ISDN cable to the BRI socket. See the following picture to connect your modem to the GEO port of your Macintosh and the ISDN cable to the BRI socket. After the cable installat ...

  • Digicom Tintoretto - page 7

    2.2 Installation 2.1.3. INTORETT O PC-CARD PCMCIA The T intoretto PC Card is compliant with any PCMCIA 2.0 socket.Insert the card in the PCMCIA slot of your computer the correct way up. The way up sign is on the modem sticker . Connect the ISDN cable to the external line inerface of Tintoretto. For the next step see the section Software Installatio ...

  • Digicom Tintoretto - page 8

    Installation 2.3 3. From the window Install New Modem put a tick in the box “Don’t detect my modem: I will select it from a list” and select the button: Next. 4. From the new window Install New Modem click the button Disk ...

  • Digicom Tintoretto - page 9

    2.4 Installation 5. Insert the Floppy disk or the CD ROM in the appropriate drive and from the window : Install from disk check that the correct driver letter appears showing where your Floppy/CD ROM is inserted (eg. A or D), then click the button OK. 6. From the list select the driver to use (e.g. Digicom Tintoretto PPP) and click Next 7. Select t ...

  • Digicom Tintoretto - page 10

    Installation 2.5 Y our modem is installed and ready to make the first connection. 2.2.2. WINDOWS 95/NT4.0 PC CARD VERSION The installation of the driver for the PC Card (PCMCIA) is a little bit different for WIN95 release 4.00.950 or 4.00.950A or 4.00.950B. In this section is described the procedure for NT4.0 and WIN95 version 4.00.950B. If you hav ...

  • Digicom Tintoretto - page 11

    Description 3.1 3. DESCRIPTION 3.1. FRONT P ANEL EXTERNAL VERSION On the front panel are present LED that indicate the most important interface circuit in use and one push-button for TEST functions. In the following table, is present the complete description and function of each LED: NAME COLOR ST A TUS FUNCTION PWR green on Tintoretto powered ON D ...

  • Digicom Tintoretto - page 12

    3.2 Description 3.3. HARDW ARE SETUP EXTERNAL VERSION Inside T intoretto is present a four position dip switch and some jumper berg for the hardware setup. 3.3.1. JUMPER SETUP JUMPER POSITION DESCRIPTION DEF AUL T U1 1-2 T ransmit T ermination 100 ohm U1 2-3 The transmission channel is in high impedence l U2 1-2 Receive T ermination 100 ohm U2 2-3 ...

  • Digicom Tintoretto - page 13

    Description 3.3 3.3.2. HARDW ARE SETUP PC CARD VERSION Inside the external line interface of T intoretto PC Card are present two jumpers used to configure the ISDN line impedence. JUMPER POSITION DESCRIPTION DEF AUL T J2 Insert T ransmission impedence 100 Ohm J2 Not inserted T ransmission at high impedence l J3 Insert Receiver impedance 100 Ohm J3 ...

  • Digicom Tintoretto - page 14

    3.4 Description Dip Switch Setting In the following table are described all the possible combination to set the communication port (COM1 to COM4) properly . COM ADD. IRQ 1 2 3 4 5 6 7 8 l 1 3F8 4 OFF OFF OFF ON OFF OFF OFF OFF l 2 2F8 3 OFF ON ON OFF OFF OFF OFF OFF l 3 3E8 4 ON OFF OFF ON OFF OFF OFF OFF l 4 2E8 3 ON ON ON OFF OFF OFF OFF OFF 1 3F ...

  • Digicom Tintoretto - page 15

    Description 3.5 ST ART DA T A P ARITY STOP TOT 17 1 1 1 0 18 0 1 1 0 17 0 2 1 0 18 1 1 1 1 The modem will accept even, odd, mark, or space. 3.4.1. A T COMMAND SET OF TINTORETTO COMMAND DESCRIPTION A T Attention A/ Repeat last command A Answer incoming data call DD i a l E Echo commands ON/OFF H Hang up I Interrogate product status N Selct speed con ...

  • Digicom Tintoretto - page 16

    3.6 Description COMMAND DESCRIPTION *I Caller Identification function (CALLER ID) *K CTS (C106) during the handshaking *M MultiSubscriber Number function (MSN) *S Subaddress function *X Clock in Off-Line %A2 CSD call type (V .1 10 or V .120) %A3 Select data channel %C V42bis data compression (see also &U command) %F Flash eprom upgrade facility ...

  • Digicom Tintoretto - page 17

    Description 3.7 DS=0-19 Dial the dial string associated to the memory location (from 0 to 19) stored using &Z command Dn1*n2 Dial two number (n1 and n2) for MLPPP at 128Kbps. If the service access at 128Kbps is over a single telephone number the n1 is egual to n2. Example: A TD70261 1*70261 1 See also the command A%A2 for MLPPP activation Store ...

  • Digicom Tintoretto - page 18

    3.8 Description Q Returns code Enable or disable the return codes from Tintoretto to the Computer . Q0 Messages transmission enabled Q1 Messages transmission disabled Q3 Reserved Q4 Reserved Q5 Reserved Store: S14 (bit 0,2,4) S52 (bit 0) Default= Q0 S S Registers Show and change the contect of "r" register Sr=xxx Store the number xxx, in ...

  • Digicom Tintoretto - page 19

    Description 3.9 NUMERIC VERBOSE 0O K 1 CONNECT 2R I N G 3 NO CARRIER 4 ERROR 6 NO DIAL TONE 7 BUSY 5 CONNECT 1200 10 CONNECT 2400 1 1 CONNECT 4800 12 CONNECT 9600 14 CONNECT 19200 28 CONNECT 38400 32 CONNECT 48000 18 CONNECT 57600 19 CONNECT 64000 20 CONNECT 1 15200 46 CARRIER 1200 47 CARRIER 2400 48 CARRIER 4800 49 CARRIER 7200 50 CARRIER 9600 54 ...

  • Digicom Tintoretto - page 20

    3.10 Description Z Load user configuration Reset T intoretto and load a user configuration stored in non volatile memory . Z0 Load user configuration n. 0 Z1 Load user configuration n. 1 Z2 Load user configuration n. 2 Z3 Load user configuration n. 3 Store: n/a Default= n/a C C109 (DCD) Control Determine how the state of the C109 relates to the dat ...

  • Digicom Tintoretto - page 21

    Description 3.11 &K4 Bi-directional software XON/XOFF (Tintoretto —> Computer and Computer —> Tintoretto) flow control. The T intoretto doesn’t transmit to the remote the XON/XOFF chars received from the Computer . &K8 Unidirectional software XON/XOFF (Tintoretto —> Computer) flow control. The T intoretto doesn’t recogniz ...

  • Digicom Tintoretto - page 22

    3.12 Description &S C107 (DSR) control Establish how the C107 (DSR) will operate. &S0 C107 (DSR) is always ON. &S1 C107 (DSR) function as standard; DSR is ON when the connection is established and will be OFF when Tintoretto hangs-up. Store: S21 Default=&S0 &T Enable or disable Loop test Allow to select the of loop test. &T0 ...

  • Digicom Tintoretto - page 23

    Description 3.13 &Y Define the user configuration to be loaded at power on Define what user configuration, stored using the &W command, must be loaded at T intoretto power on. &Y0 Load the user configuration stored to user memory 0. &Y1 Load the user configuration stored to user memory 1. &Y2 Load the user configuration stored t ...

  • Digicom Tintoretto - page 24

    3.14 Description *M MultiSubscriber Number function (MSN) The MultiSubscriber Number permits the association of maximum 8 consecutive numbers to a BRI access of the national plan number . There’s a principal number with the last digit always equal to “0” and associated with it is an auxiliary number that may vary between “1” and “7”. ...

  • Digicom Tintoretto - page 25

    Description 3.15 %A2=2 V .120 protocol. %A2=5 PPP protocol at 64Kbps %A2=6 MLPPP protocol at 128Kbps Store: S15 Default=%A2=1 %A3 Select Data Channel %A3=2 Preferred B1 channel. If busy, Tintoretto try to use the B2 channel %A3=3 Forced B1 channel. If busy , T intoretto hangs-up the communication %A3=4 Preferred B2 channel. If busy, Tintoretto try ...

  • Digicom Tintoretto - page 26

    3.16 Description It is important to remember that the CCITT rules for the asincronus V25bis function, provide a format of 7 data bit Even parity . T o return in A T command from V25bis command set (%V1 or %V3), turn ON the Tintoretto pushing the TEST push-button for minimum 5 seconds. Store: S31 (bit 0, 1, 7) Default= %V0 %Z1 Master reset Master re ...

  • Digicom Tintoretto - page 27

    Description 3.17 !N2=”nnnn” where “nnnn” is composed of prefix + number (p.e. 331263122) !N2? show the stored MultiSubscriber number T o enable the MultiSubscriber Number function, please also make reference to the A T*M command. Store: yes Default= n/a !N3= Store Subaddress number This command enable to store the Subbaddres field for the S ...

  • Digicom Tintoretto - page 28

    3.18 Description S1 RING count Number of ring in a period of 8 seconds. V alue Unit Function 0 RING No ring in a period of 8 seconds 1-5 RING RING count Default=0 T ype:Non Storable S2 ESCAPE sequence character V alue Unit Function 0-127 ASCII Contain the ESCAPE sequence character . If the value is greater then 127, escape sequence is disabled. Def ...

  • Digicom Tintoretto - page 29

    Description 3.19 S13 Call W aiting time V alue Unit Function 0 sec. Call Waiting time disable 0-255 1 sec. Defines the duration of buzzer/TEST led flash when arrives a new call. Default=30 T ype:Storable S25 DTR control V alue Unit Function 0-255 sec/100 Sets the length of time that the modem will ignore DTR for before hanging up. Default =5 T ype: ...

  • Digicom Tintoretto - page 30

    3.20 Description 6 = 2400 bps 15 = 4800 bps 16 = 7200 bps 17 = 9600 bps 18 = 12000 bps 19 = 14400 bps 27 = 19200 bps 50 = 38400 bps (asyncronous only) 51 = 48000 bps (syncronous only) 53 = 64000 bps (syncronous only) Default =0 Type: Storable S49 Tintoretto-DTE flow control Display the value of the &K command, which specifies DTE flow control s ...

  • Digicom Tintoretto - page 31

    Diagnostic 4.1 4. DIAGNOSTIC 4.1. DIAGNOSTIC ACTIV A TION FOR PC CARD VERSION If T intoretto is turned off and on, starts automatically the internal self test diagnostic to understand particular problem before the normal function. During the automatic diagnostic, the led present on the external interface follows this status: RED----->ORANGE----- ...

  • Digicom Tintoretto - page 32

    Declaration CE of Conformity V DECLARA TION OF CONFORMITY This product satisfies the basic requirements of Electromagnetic Compatibility and Safety of the below indicated Directive: l 91/263/EEC of 29 april 1991 (Directive 93/68/CEE of july 22,1993 and Directive 93/97/ CEE of 29 october 1993). CHECK REPORT The equipment has been successfully tested ...

Manufacturer Digicom Category Router

Documents that we receive from a manufacturer of a Digicom Tintoretto can be divided into several groups. They are, among others:
- Digicom technical drawings
- Tintoretto manuals
- Digicom product data sheets
- information booklets
- or energy labels Digicom Tintoretto
All of them are important, but the most important information from the point of view of use of the device are in the user manual Digicom Tintoretto.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Digicom Tintoretto, service manual, brief instructions and user manuals Digicom Tintoretto. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Digicom Tintoretto.

Similar manuals

A complete manual for the device Digicom Tintoretto, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Digicom Tintoretto by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Digicom Tintoretto.

A complete Digicom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Digicom Tintoretto - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Digicom Tintoretto, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Digicom Tintoretto, that we can find in the current document
3. Tips how to use the basic functions of the device Digicom Tintoretto - which should help us in our first steps of using Digicom Tintoretto
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Digicom Tintoretto
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Digicom Tintoretto in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Digicom Tintoretto?

Use the form below

If you did not solve your problem by using a manual Digicom Tintoretto, ask a question using the form below. If a user had a similar problem with Digicom Tintoretto it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)