English dropdown-ico

Manual Seagate ST410800N/ND

40 pages 0.34 mb
Download

Go to site of 40

Summary
  • Seagate ST410800N/ND - page 1

    Elite 9 Disc Drive ST410800N/ND ST410800W/WD Installation Guide ...

  • Seagate ST410800N/ND - page 2

    2 Elite 9 Installation Guide, Rev. B Contents Preface .................................................................. 1 Electrostatic discharge protection ........................... 1 Important safety information and precautions ......... 2 Wichtige Sicherheitshinweise ............................... 5 Technical support services ............... ...

  • Seagate ST410800N/ND - page 3

    Elite 9 Installation Guide, Rev. B 1 Preface This manual contains information for users of Seagate ® Elite™ 9 SCSI disc drives. It provides support services, performance specifications, and initial setup informa- tion. Additional information is available in the Elite 9 Product Manual (part number 83328860). Contact your Seagate sales representat ...

  • Seagate ST410800N/ND - page 4

    2 Elite 9 Installation Guide, Rev. B • Ground yourself to the drive whenever the drive elec- tronics are or will be exposed. Connect yourself to ground with a wrist strap (Seagate part number 12263496). Connection may be made to any grounded metal assembly. As a general rule, remember that you and the drive electronics must all be grounded to avo ...

  • Seagate ST410800N/ND - page 5

    Elite 9 Installation Guide, Rev. B 3 read and followed to minimize or eliminate the risk of personal injury. The warnings point out conditions or practices that may endanger you or others. The cautions point out conditions or practices that may damage the unit, possibly making it unsafe for use. These warnings and cautions are not exhaustive. We ca ...

  • Seagate ST410800N/ND - page 6

    4 Elite 9 Installation Guide, Rev. B • Ensure that the internal temperature of the rack or cabinet does not exceed the limits defined for the drive when the drive is mounted in an equipment rack or cabinet. When units are stacked vertically, pay atten- tion to the top where temperatures are usually highest. • Follow the precautions listed above ...

  • Seagate ST410800N/ND - page 7

    Elite 9 Installation Guide, Rev. B 5 dards. Typical applications of these disc drives include customer packaging and subsystem design. Safety agencies conditionally certify component assemblies, such as the Elite disc drive, based on their final acceptability in the end-use product. The subsystem designers are responsible for meeting these conditio ...

  • Seagate ST410800N/ND - page 8

    6 Elite 9 Installation Guide, Rev. B dürfen nur von qualifiziertem Fachpersonal vorgenommen werden. Wir empfehlen die Verfahren in diesem Handbuch als effektive Methoden zur Wartung und Reparatur der Einheit. Einige Verfahren erfordern Spezialwerkzeuge; diese müssen zur sachgemäßen Ausführung der Wartungsarbeiten und aus Sicherheitsgründen de ...

  • Seagate ST410800N/ND - page 9

    Elite 9 Installation Guide, Rev. B 7 zuerst sicher, daß das gewählte Verfahren weder Ihre persönliche Sicherheit noch die Leistung der Einheit gefährdet. Beachten Sie in jedem Fall die folgenden Warn-und Vorsichtshinweise: • Führen Sie alle Wartungsarbeiten entsprechend den Anweisungen in diesem Handbuch aus. • Beachten Sie alle Warn- und ...

  • Seagate ST410800N/ND - page 10

    8 Elite 9 Installation Guide, Rev. B • Befolgen Sie die oben unter “Electrostatic Discharge Protection” angegebenen Sicherheitsmaßnahmen. • Nehmen Sie keine Platinen aus dem Laufwerkgehäuse. Wenn eine Platine defekt ist, muß das gesamte Laufwerk zur Reparatur eingeschickt werden. Die Herausnahme von Platinen durch andere Personen als die ...

  • Seagate ST410800N/ND - page 11

    Elite 9 Installation Guide, Rev. B 9 geltenden Standards zu gewährleisten. Zu den typischen Anwendungen dieser Festplattenwerke zählen Systemeinbau durch den Kunden und die Konstruktion von Untersystemen. Sicherheitsbehörden gewähren eine bedingte Zulassung für Komponenten wie das Elite- Festplattenlaufwerk vorbehaltlich der endgültigen Zulas ...

  • Seagate ST410800N/ND - page 12

    10 Elite 9 Installation Guide, Rev. B Technical support services Seagate Technology provides technical support litera- ture and diagnostic utilities to authorized distributors. Please contact your dealer for technical support and installation troubleshooting. Product technical support is available for all Seagate products by calling the SeaFAX™, ...

  • Seagate ST410800N/ND - page 13

    Elite 9 Installation Guide, Rev. B 11 access this service, which is available from 8:00 A . M . to 5:00 P . M . PST, Monday through Friday. SeaBOARD: The Seagate Technical Support Bulletin Board System (BBS) is available 24 hours a day, 7 days a week. A modem is required to access this service. The commu- nications software must be set for 8 data b ...

  • Seagate ST410800N/ND - page 14

    12 Elite 9 Installation Guide, Rev. B General description Elite 9 SCSI disc drives are high capacity, random- access digital-data storage devices. An Elite 9 drive is illustrated in Figure 1. Specifications and DC power requirements for the drive are listed in a table following the figure. The drive is a component for installation in an enclosure d ...

  • Seagate ST410800N/ND - page 15

    Elite 9 Installation Guide, Rev. B 13 DC Power Connector J4A SCSI I/O Connector J4B J01 Figure 1. Elite 9 family disc drive (ST410800N shown) ...

  • Seagate ST410800N/ND - page 16

    14 Elite 9 Installation Guide, Rev. B Characteristics of ST410800 drives N/ND W/WD SCSI-2 Interface 1 Fast Fast & Wide Multi-segmented cache Physical 1,024 Kbytes 1,024 Kbytes Available to user 960 Kbytes 960 Kbytes Capacity Unformatted 10,800 Mbytes 10,800 Mbytes Formatted 2 9,090 Mbytes 9,090 Mbytes Recording Cylinders (user access ible) 4,92 ...

  • Seagate ST410800N/ND - page 17

    Elite 9 Installation Guide, Rev. B 15 DC power requirements for ST410800N/ND drives Single-ended Differential + + + + + 5V 11 + + + + + 12V + + + + + 5V 11 + + + + + 12V Voltage regulation 5 ± ± ± ± ± 5% ± ± ± ± ± 5% 2 ± ± ± ± ± 5% ± ± ± ± ± 5% 2 Amps Max operating current DC 3 σ 1 0.95 1.85 1.4 1.85 Avg idle current DC X 1, 12 ...

  • Seagate ST410800N/ND - page 18

    16 Elite 9 Installation Guide, Rev. B DC power requirements for ST410800W/WD drives Single ended Differential 5V [11] 12V 5V [11] 12V Voltage regulation [5] ± ± ± ± ± 5% ± ± ± ± ± 5% [2] ± ± ± ± ± 5% ± ± ± ± ± 5% [2] Amps Max operating current DC 3 σ 1 1.0 1.94 1.27 1.94 Avg idle current DC X 1, 12 0.7 1.56 1.0 1.56 Max startin ...

  • Seagate ST410800N/ND - page 19

    Elite 9 Installation Guide, Rev. B 17 1 Measured with an average reading DC ammeter. Instan- taneous +12V current peaks will exceed these values. 2 A − 10% tolerance is permissible during initial start of the spindle but m ust return t o ± 5% before reaching 5,400 RP M. The ± 5% must be maintained after the drive signifies that its power-up seq ...

  • Seagate ST410800N/ND - page 20

    18 Elite 9 Installation Guide, Rev. B continued from previous page 12 All power-saving features are enabled. 13 Seeking is defined as a third-stroke seek at OD. A com- mand is issued every 23 msec. 14 Read track is defined as repeat reads of track 15 with an 88% duty cycle. 15 Operating condition is a third-stroke seek at OD and read 1 track. A com ...

  • Seagate ST410800N/ND - page 21

    Elite 9 Installation Guide, Rev. B 19 Setting the SCSI ID jumpers Each device on the SCSI chain must have a unique SCSI ID. The host system’s SCSI controller usually uses the highest-numbered ID available (ID7 in non-wide sys- tems); therefore the lower-numbered SCSI IDs are nor- mally used for the other SCSI devices such as this Elite disc drive ...

  • Seagate ST410800N/ND - page 22

    20 Elite 9 Installation Guide, Rev. B SCSI ID = 0 (factory setting) SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 J4A SCSI ID = 8* SCSI ID = 9* SCSI ID = Ah (10)* SCSI ID = Bh (11)* SCSI ID = Ch (12)* SCSI ID = Dh (13)* SCSI ID = Eh (14)* SCSI ID = Fh (15)* *Applicable only for W- and WD-type drives. DC Power? ...

  • Seagate ST410800N/ND - page 23

    Elite 9 Installation Guide, Rev. B 21 Terminating the drive If you are installing the drive in a system that has other SCSI devices installed, terminate only the end devices on the SCSI chain. A SCSI “device” is any disc drive, scanner, tape backup unit, or other piece of hardware connected to your system using the SCSI bus. The top example in ...

  • Seagate ST410800N/ND - page 24

    22 Elite 9 Installation Guide, Rev. B To terminate ST410800N and ST410800W drives, en- able the permanently mounted IC terminators by install- ing a jumper on J4A pins 19 and 20 as shown in Figure 4. If you install one of these models and it is not on the end of the SCS I bu s, r em ov e i nte rna l te rmi n a tion f r om the dr ive by removing the ...

  • Seagate ST410800N/ND - page 25

    Elite 9 Installation Guide, Rev. B 23 ST410800ND and ST410800WD (differential) drives are shipped with terminators (part number 15479501) in- stalled on the circuit board. Figure 5 illustrates the locations of the terminators. To remove termination from the drive, carefully lift the terminators from their sockets. Wide I/O Connector ST410800WD I ...

  • Seagate ST410800N/ND - page 26

    24 Elite 9 Installation Guide, Rev. B Internal terminator power  source (factory setting) External terminator  power source Internal terminator  power to I/O J01 4 J01 2 3 1 Terminator  Power Option Pin 4 Pin 3 Pin 1 Pin 2 Figure 6. Setting terminator power jumpers (ST410800N shown) Changing other applicable jumper options Elite 9 drive ...

  • Seagate ST410800N/ND - page 27

    Elite 9 Installation Guide, Rev. B 25 Write Protect Reserved J4A DC Power Connector J4A SCSI I/O Connector J4B J01 Spinup delay equal to the SCSI bus ID multiplied by 10 seconds. Valid only if the Start Command jumper is disconnected. J4B Spinup Delay Option Pin 1 Immediate spinup. Valid only if the Start Command  Option jumper is disconne ...

  • Seagate ST410800N/ND - page 28

    26 Elite 9 Installation Guide, Rev. B Spindle Sync Cable Connector J4A SSREF DC Power Connector J4A SCSI I/O Connector J4B J01 Pin 1 Figure 8. Spindle sync jumpers and connectors (ST410800N shown) Synchronizing spindles in multiple drive configurations If you are installing two or more Elite 9 drives, you may (optionally) synchronize their sp ...

  • Seagate ST410800N/ND - page 29

    Elite 9 Installation Guide, Rev. B 27 Figure 9 illustrates a typical synchronized spindle configuration. After connecting each drive with spindle sync cables, you must designate a master spindle sync reference source. This master source is normally a disc drive located on the same SCSI bus as the other drives you want to synchronize with. To design ...

  • Seagate ST410800N/ND - page 30

    28 Elite 9 Installation Guide, Rev. B Providing adequate cooling The enclosure design must ensure adequate cooling for the drive. The maximum ambient temperature is 45 o C. The drive’s product manual (83328860) describes how to evaluate the air-flow design. The evaluation consists of ensuring that the case temperature of certain critical componen ...

  • Seagate ST410800N/ND - page 31

    Elite 9 Installation Guide, Rev. B 29 Kühlung des Systems Die Gehäusekonstruktion muß eine ausreichende Kühlung des Laufwerkes gewährleisten. Die Umgebungstemperatur darf maximal 45 o C betragen. Die Produkthandbuch Elite 9 (Dokument 83328860) enthalten Anweisungen zur Beurteilung der Luftstromkonstruktion. Die Beurteilung muß sicherstellen, ...

  • Seagate ST410800N/ND - page 32

    30 Elite 9 Installation Guide, Rev. B Note. Air flows in the direction shown (front to back) or in reverse direction (back to front) Above unit Über der Einheit Under unit Unter der Einheit Note. Air flows in the direction shown or in reverse direction (side to side) Above unit Über der Einheit Under unit Unter der Einheit Hinwe ...

  • Seagate ST410800N/ND - page 33

    Elite 9 Installation Guide, Rev. B 31 Mounting the drive and connecting cables Do not touch the connector pins or any components on the control board without observing static-discharge precautions. Always handle the drive by the frame only. The drive may be mounted in any orientation (horizon- tally, vertically, and any combination thereof); howeve ...

  • Seagate ST410800N/ND - page 34

    32 Elite 9 Installation Guide, Rev. B Installation des Laufwerkes und Anschluß der Kabel Beachten Sie beim Handhaben und Anfassen der Anschlußstifte und Komponenten die Vorsichtsmaßnahmen zur Verhinderung statischer Aufladung. Fassen Sie das Laufwerk nur am Rahmen an. Das Laufwerk kann in beliebiger Orientierung (horizon- tal, vertikal oder schr ...

  • Seagate ST410800N/ND - page 35

    Elite 9 Installation Guide, Rev. B 33 K M4 x .70 Metric Threads (4) B C D E F J C.G. L 6-32 Threads (4) C.G. I I G H A Side A B C D E F G H I J K L 3.25 0.86 0.39 1.93 3.120 8.06 5.50 5.75 0.12 3.90 1.55 3.15 0.01 0.01 0.01 0.01 0.005 0.01 0.01 0.01 0.05 0.05? ...

  • Seagate ST410800N/ND - page 36

    34 Elite 9 Installation Guide, Rev. B 2. Verify that all connections between the drive and the host system are correctly installed. 2. Prüfen Sie, ob alle Verbindungen zwischen dem Laufwerk und dem Host-System korrekt hergestellt sind. 3. Verify that you have correctly installed SCSI ID jump- ers and that you have properly terminated the SCSI bus ...

  • Seagate ST410800N/ND - page 37

    Elite 9 Installation Guide, Rev. B 35 Pin 1 2 3 4 Power +12V +12V return + 5V return + 5V 4321 Pin 1 2 3 4 Gleichstrom +12V +12V Rückleitung + 5V Rückleitung + 5V 4. Schließen Sie das 50-polige SCSI-Kabel an den SCSI-Steckverbinder des Laufwerkes an (wie bereits in Abbildung 1 gezeigt). Das Kabel d ...

  • Seagate ST410800N/ND - page 38

    36 Elite 9 Installation Guide, Rev. B Note. Signal ground on the power control board (PCB) and the head and disc assembly (HDA) are con- nected together in this drive and you cannot separate them. The equipment in which you have mounted the drive is connected directly to the HDA and PCB without electrically isolating shock mounts. Maximizing the co ...

  • Seagate ST410800N/ND - page 39

    Elite 9 Installation Guide, Rev. B 37 Systemgehäuse nicht an die HDA/PCB-Erdung anschließen wollen, müssen Sie das Laufwerk auf nichtleitende Weise (galvanisch isoliert) im Host- System einbauen. Die daraus u.U. resultierende verstärkte elektromagnetische Strahlung fällt in den Zuständigkeitsbereich des Systemdesigners. 5. Replace the host sy ...

  • Seagate ST410800N/ND - page 40

    38 Elite 9 Installation Guide, Rev. B Seagate Technology, Inc. 920 Disc Drive, Scotts Valley, CA 95066-4544, USA Publication Number: 83328850, Rev. B, Printed in USA ...

Manufacturer Seagate Category Computer Hardware

Documents that we receive from a manufacturer of a Seagate ST410800N/ND can be divided into several groups. They are, among others:
- Seagate technical drawings
- ST410800N/ND manuals
- Seagate product data sheets
- information booklets
- or energy labels Seagate ST410800N/ND
All of them are important, but the most important information from the point of view of use of the device are in the user manual Seagate ST410800N/ND.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Seagate ST410800N/ND, service manual, brief instructions and user manuals Seagate ST410800N/ND. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Seagate ST410800N/ND.

Similar manuals

A complete manual for the device Seagate ST410800N/ND, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Seagate ST410800N/ND by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Seagate ST410800N/ND.

A complete Seagate manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Seagate ST410800N/ND - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Seagate ST410800N/ND, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Seagate ST410800N/ND, that we can find in the current document
3. Tips how to use the basic functions of the device Seagate ST410800N/ND - which should help us in our first steps of using Seagate ST410800N/ND
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Seagate ST410800N/ND
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Seagate ST410800N/ND in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Seagate ST410800N/ND?

Use the form below

If you did not solve your problem by using a manual Seagate ST410800N/ND, ask a question using the form below. If a user had a similar problem with Seagate ST410800N/ND it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)