English dropdown-ico

Manual Weider WESY37530

37 pages 3.11 mb
Download

Go to site of 37

Summary
  • Weider WESY37530 - page 1

    CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY37530 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfact ...

  • Weider WESY37530 - page 2

    2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . ...

  • Weider WESY37530 - page 3

    3 IMPORT ANT PRECAUTIONS 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only . Do not use the weight system in ...

  • Weider WESY37530 - page 4

    ASSEMBLED DIMENSIONS: Height: 90 in. Width: 87 in. Depth: 77 in. 4 Leg Lever High Pulley Station Ab Pulley Station Lat Bar Backrest Knob Foot Plate Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the seat; they do not correspond to right and left on the drawings in the manual. ...

  • Weider WESY37530 - page 5

    5 Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape. Note: Assembly will be more convenient if you have a socket set, a set of open-end ...

  • Weider WESY37530 - page 6

    1. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press a 40mm x 60mm Inner Cap (42) into the Right Base (1). Insert four M10 x 53mm Carriage Bolts (83) up through the Right Base (1). Note: It may be helpful to place tape over the heads of the Carriage Bolts to hold them in place. 2. Press three 40mm x 60mm Inner Caps (42) into the L ...

  • Weider WESY37530 - page 7

    7 4. Attach the Right Upright (5) to the Right Base (1) with the indicated two M10 x 53mm Carriage Bolts (83) and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet. Attach the Left Upright (6) to the Left Base (2) with the indicated two M10 x 53mm Carriage Bolts (83) and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet. Attac ...

  • Weider WESY37530 - page 8

    8 6. Press a 50mm x 75mm Inner Cap (45) into the Right Seat Frame (3). Orient the Right Seat Frame (3) as shown. Attach the Right Seat Frame to the Right Leg (7) with two M10 x 78mm Bolts (86), two M10 W ashers (74), and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet. Attach the Right Seat Frame (3) to the Right Upright (5) with two M ...

  • Weider WESY37530 - page 9

    9 10. Slide sixteen Weights (30) onto the W eight Guides (9). Make sure the slots for the Weight Pin (not shown) are on the indicated side and on the bottom of the Weights. Press a Weight Tube Bumper (35) into a W eight T ube (34). Insert the Weight T ube into the stack of Weights (30) as shown. Lubricate the indicated holes in a T op W eight (31) ...

  • Weider WESY37530 - page 10

    10 1 1. Press a 40mm x 60mm Inner Cap (42) and two 40mm x 60mm Thick Inner Caps (89) into the Left T op Frame (1 1). Attach the Left T op Frame (1 1) to the Left Upright (6) with two M10 x 62mm Bolts (92), a Support Plate (29), and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet. 12. Press a 40mm x 60mm Inner Cap (42) into the Right T ...

  • Weider WESY37530 - page 11

    15. Open the part bag labeled “ARM ASSEMBL Y .” Press a 50mm x 75mm Inner Cap (45) into the Leg Press Arm (12). Lubricate an M12 x 104mm Bolt (67) with grease. Attach the Leg Press Arm (12) to the Right Base (1) with the Bolt and an M12 Nylon Locknut (81). Do not overtighten the Locknut; the Leg Press Arm must be able to pivot easily . 16. Lubr ...

  • Weider WESY37530 - page 12

    12 19. Press two 50mm Square Inner Caps (43) into the Leg Lever (18). Lubricate an M10 x 78mm Bolt (86) with grease. Orient the Leg Lever (18) as shown and attach it to the Left Leg (8) with the Bolt and an M10 Nylon Locknut (75). Do not overtighten the Locknut; the Leg Lever must be able to pivot easily . 20. Lubricate both axles on the Left T op ...

  • Weider WESY37530 - page 13

    13 22. Lubricate an M10 x 81mm Bolt (85) with grease. Attach the left Butterfly Arm (20) to the Left Fly Pivot (21) with the Bolt and an M10 Nylon Locknut (75). Attach the right Butterfly Arm (20) to the Right Fly Pivot (22) in the same manner . 23. Locate the High Cable (61). Route the small ball on the Cable (61) through the Right Upright (5) and ...

  • Weider WESY37530 - page 14

    14 26. Route the High Cable (61) up through the Right T op Frame (10) and over a 90mm Pulley (38). Attach the Pulley inside the T op Frame with an M10 x 78mm Bolt (86), two M10 W ashers (74), two 17mm Spacers (58), and an M10 Nylon Locknut (75). 27. Route the High Cable (61) over a 90mm Pulley (38) and down through the Right T op Frame (10). Attach ...

  • Weider WESY37530 - page 15

    15 31. Route the Short Cable (62) over a 90mm Pulley (38). Attach the Pulley to the front bracket on the Right T op Frame (10) with an M10 x 45mm Bolt (78) and an M10 Nylon Locknut (75). 31 62 78 75 38 10 Front Bracket 32. Thread an M12 Nut (80) onto the Short Cable (62) as far as it will go. Slide a 50mm W asher (59) onto the Cable and thread the ...

  • Weider WESY37530 - page 16

    35. Route the Low Cable (63) through the Leg Lever (18), around a 90mm Pulley (38), and back through the Leg Lever and Left Leg (8). Attach the Pulley inside the Leg Lever with an M10 x 67mm Bolt (88), two M10 W ashers (74), two 12mm Spacers (57), and an M10 Nylon Locknut (75). 35 57 57 75 74 38 63 18 8 16 36. Wrap the Low Cable (63) under a 90mm P ...

  • Weider WESY37530 - page 17

    17 40. Wrap the Low Cable (63) around a “V”-pulley (40). Attach the “V”-pulley and a Large Cable T rap (39) to the center bracket on the Left Upright (6) with an M10 x 60mm Bolt (82) and an M10 Nylon Locknut (75). Make sure that the Cable T rap is turned to hold the Cable in the groove of the “V”-pulley . 42. Note: The “V”-pulley (4 ...

  • Weider WESY37530 - page 18

    18 43. Wrap the Low Cable (63) under a 90mm Pulley (38). Attach the Pulley and a Cable T rap (37) to the Left Base (2) with an M10 x 48mm Bolt (23) and an M10 Nylon Locknut (75). Make sure that the Cable T rap is turned to hold the Cable in place. 43 75 38 63 37 23 2 44. Wrap the Low Cable (63) under a 90mm Pulley (38). Attach the Pulley and a Cabl ...

  • Weider WESY37530 - page 19

    19 48. Wrap the Low Cable (63) over a 90mm Pulley (38). Attach the Pulley and a Cable T rap (37) to the second set of holes from the bottom of the Double “U”-bracket (41) with an M10 x 48mm Bolt (23) and an M10 Nylon Locknut (75). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley . 51. Wrap the Low Cable (63) und ...

  • Weider WESY37530 - page 20

    20 53. Wrap the Low Cable (63) over a 90mm Pulley (38). Attach the Pulley and a Cable T rap (37) to the Leg Press Arm (12) with an M10 x 120mm Bolt (76), an M10 W asher (74), and an M10 Nylon Locknut (75). Make sure that the Cable T rap is turned to hold the Cable in place. Do not tighten the Locknut yet. 54. Wrap the Low Cable (63) around a 90mm P ...

  • Weider WESY37530 - page 21

    21 59. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Seat (26) with the serial number decal to the Left Seat Frame (4) with four M6 x 16mm Screws (79). Attach the other Seat (26) to the Right Seat Frame (not shown) in the same manner . 59 26 Wide End Serial Number Decal 4 79 Seat Assembly 58. Remove the M10 Nylon Locknut ...

  • Weider WESY37530 - page 22

    22 62. Attach the Curl Pad (28) to the Curl Post (19) with four M6 x 16mm Screws (79). 62 28 79 19 63. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page. Before using the weight system, pull each cable a few times to make sure that the cables move ...

  • Weider WESY37530 - page 23

    This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 29 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise. IMPORT ANT : When attaching the accessories, make sure that they are in the co ...

  • Weider WESY37530 - page 24

    24 CHANGING THE WEIGHT SETTING T o change the setting of a weight stack, insert a Weight Pin (32) under the desired W eight (30). Insert the Weight Pin so that the bent end touches the weight stack. T urn the bent end down. Note: Due to the cables and pulleys, the amount of resistance at each exercise station may vary from the weight setting. Use t ...

  • Weider WESY37530 - page 25

    WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “T op” refers to the 6 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. W eight resistance shown for the butterfly arm sta- tion is for each butterfly arm. Note: The actual resistance at each station may vary due to d ...

  • Weider WESY37530 - page 26

    26 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when ...

  • Weider WESY37530 - page 27

    CABLE DIAGRAMS The cable diagrams show the proper routing of the High Cable (61), the Short Cable (62), and the Low Cable (63). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight system will not function properly and damage may occur . The number ...

  • Weider WESY37530 - page 28

    9 11 12 13 8 14 5 15 16 17 18 19 20 24 25 26 21 22 23 7 10 Low Cable (63) Length: 52 feet 10 inch 1 4 6 3 2 28 ...

  • Weider WESY37530 - page 29

    29 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS MUSCLE BUILDING T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise. Y ou can adjust the intensity level of an individual exercise in two w ...

  • Weider WESY37530 - page 30

    30 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout. Plan to spend the first couple of weeks familiarizing yourself wit ...

  • Weider WESY37530 - page 31

    31 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts. ...

  • Weider WESY37530 - page 32

    M10 x 48mm Bolt (23) M10 x 45mm Bolt (78) M10 x 25mm Button Screw (60) M10 Nylon Locknut (75) M8 Nylon Locknut (54) M4 W asher (84) 50mm W asher (59) M4 x 25mm Self-tapping Screw (77) M6 x 16mm Screw (79) M6 x 20mm Screw (64) M8 x 20mm Shoulder Bolt (36) M12 Nut (80) M10 W asher (74) M12 Nylon Locknut (81) P ART IDENTIFICA TION CHART— Model No. W ...

  • Weider WESY37530 - page 33

    M10 x 120mm Bolt (76) M10 x 60mm Bolt (82) M10 x 78mm Bolt (86) M10 x 70mm Bolt (87) M10 x 81mm Bolt (85) M10 x 67mm Bolt (88) M10 x 1 10mm Bolt (90) M10 x 53mm Carriage Bolt (83) M12 x 104mm Bolt (67) M10 x 62mm Bolt (92) M10 x 91mm Bolt (91) ...

  • Weider WESY37530 - page 34

    19mm Round Inner Cap (24) 25mm Retainer Ring (53) 40mm x 60mm Inner Cap (42) 40mm x 60mm Thick Inner Cap (89) 50mm x 75mm Inner Cap (45) 50mm Square Inner Cap (43) 60mm Square Inner Cap (46) 25mm Round Outer Cap (47) 25mm Round Inner Cap (65) 38mm Square Inner Cap (44) ...

  • Weider WESY37530 - page 35

    P ART LIST—Model No. WESY37530 R1003A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 Right Base 2 1 Left Base 3 1 Right Seat Frame 4 1 Left Seat Frame 5 1 Right Upright 6 1 Left Upright 7 1 Right Leg 8 1 Left Leg 9 2 Weight Guide 10 1 Right T op Frame 1 1 1 Left T op Frame 12 1 Leg Press A ...

  • Weider WESY37530 - page 36

    42 92 86 74 58 38 58 74 75 75 47 47 75 38 78 10 38 58 74 86 75 74 61 58 65 27 26 42 83 75 75 74 75 49 75 77 7 46 79 86 86 75 37 38 3 79 79 45 38 86 86 37 76 23 37 38 23 75 41 23 75 37 38 1 83 75 75 75 73 72 50 34 35 31 30 82 39 40 75 75 40 75 39 82 42 74 86 74 86 6 48 44 75 74 74 75 75 42 74 86 86 86 23 68 69 68 70 71 83 38 37 74 86 78 38 75 2 83 7 ...

  • Weider WESY37530 - page 37

    Part No. 202143 R1003A Printed in China © 2003 ICON Health & Fitness, Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the ...

Manufacturer Weider Category Home Gym

Documents that we receive from a manufacturer of a Weider WESY37530 can be divided into several groups. They are, among others:
- Weider technical drawings
- WESY37530 manuals
- Weider product data sheets
- information booklets
- or energy labels Weider WESY37530
All of them are important, but the most important information from the point of view of use of the device are in the user manual Weider WESY37530.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Weider WESY37530, service manual, brief instructions and user manuals Weider WESY37530. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Weider WESY37530.

Similar manuals

A complete manual for the device Weider WESY37530, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Weider WESY37530 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Weider WESY37530.

A complete Weider manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Weider WESY37530 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Weider WESY37530, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Weider WESY37530, that we can find in the current document
3. Tips how to use the basic functions of the device Weider WESY37530 - which should help us in our first steps of using Weider WESY37530
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Weider WESY37530
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Weider WESY37530 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Weider WESY37530?

Use the form below

If you did not solve your problem by using a manual Weider WESY37530, ask a question using the form below. If a user had a similar problem with Weider WESY37530 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)