-
GarrettCom FT14 - page 1
Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http ://www.GarrettCom .com email support@ garrettcom.com ww m c om w Garre t t C o .. www Garre t t C om c om .. MagnumFT14 and FT14H 10Mb/s Media Converters Installation and User Guide ...
-
GarrettCom FT14 - page 2
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) i www Garre t t C om com .. Magnum ™ FT14 and FT14H 10Mb/s Media Converters Installation and User Guide Part #: 84-00134 Rev. A (09/04) Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Unde ...
-
GarrettCom FT14 - page 3
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) ii www Garre t t C om com .. Federal Communications C ommission Radio Frequency I nterference Statement This equipment generates, uses and can radiate frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer's instructio ...
-
GarrettCom FT14 - page 4
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) iii www Garre t t C om com .. Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http ://www.GarrettCom .co ...
-
GarrettCom FT14 - page 5
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) iv ww Garr w e t t C om com .. TABLE OF CONTENTS Page 1.0 SPECIFICATIONS ............................................................................... 1 1.1 Technical Specifications ..................................................................... 1 1.2 Summ ary of mode ...
-
GarrettCom FT14 - page 6
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) v www Garre t t C om com .. 3.6 Connecting Ethernet Medi a ............................................................... 34 3.6.1 Connecting Twisted Pair (RJ-45 ports ) ...................................... 34 3.6.2 Connecting Fiber Optic mm , sm (half- and full-duplex) .. ...
-
GarrettCom FT14 - page 7
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) vi www Garre t t C om com .. Revisions Rev A 09/04: Minor updates on UL Requirem ents, power supplies Rev A 06/04: Minor updates on Agency approvals and power supplies Rev A 05/03: Initial release of this user manual for FT14 and FT14H GarrettCom, Inc. reserves the right to c ...
-
GarrettCom FT14 - page 8
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 1 www Garre t t C om com .. 1.0 SPECIFICATIONS 1.1 Technical Specifications Model FT14, FT14H multi-mode and single-mode Performance: Data Rate: 10 Mbps (IEEE 802.3), half duplex mode Network Standards: Ethernet: Ethernet V1.0/2.0 IEEE 802.3: 10BASE-T, 10BASE-FL IEEE 802.3, ( ...
-
GarrettCom FT14 - page 9
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 2 www Garre t t C om com .. Maximum Standard Ethernet Segment Lengths: 10BASE-T (twisted pair): 100 m (328 ft) 10BASE-FL Fiber optic : 2.0 km (6,562 ft) 10BASE-FL Single-mode Fi ber optic: 10.0 km (32,810ft) Note for single-mode: HDX collision domain lim its may restrict dist ...
-
GarrettCom FT14 - page 10
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 3 www Garre t t C om com .. Ambient Relative Hum idity: 5% to 95% (non-condensing) UL 2043 tested for above-the –ceiling (plenum) installation Conformal coating (hum id ity protection) option, request quote. Designed for NEBS compliance, including vibration, shock, and alti ...
-
GarrettCom FT14 - page 11
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 4 www Garre t t C om c om .. 100-240V AC at 50-60Hz, for high temp. with built-in IEC320 connector for “-Hi” DC to unit : “Hi” international model 9V DC, 2.5mm jack, center +ve, 6ft. cord Power Supply ( DC Direct): built-in terminal block for +, -, ground. The 9V DC j ...
-
GarrettCom FT14 - page 12
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 5 www Garre t t C om com .. RJ-45 Port: Modular 8-Pin female , with “cross-over” up-link switch Fiber Port: Fiber optic (standard ST type) Packaging: Enclosure: Rugged sheet metal (Steel). Dimensions, Media Converter unit: Height x Width x Depth FT14 and FT14H: 3.5 in H x ...
-
GarrettCom FT14 - page 13
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 6 www Garre t t C om com .. Metal Mounting clips for panel mou nting : included DIN-Rail mounting option : Model # DIN-RAIL MC2 (see Section 3.4) Rack-mount option : MC14-TRAY, see http ://www. garr ettc om. com /mc _tray. htm Mean Tine Between Failure (MTBF ) – 15+ years, ...
-
GarrettCom FT14 - page 14
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 7 www Garre t t C om com .. 1.2 Summary of models and de sc r i ptions: FT14-Hd = TP to 10Mb m m Fiber ST , external 115 60Hz AC power supply, for 0 to 50`C FT14-Hi = TP to 10Mb m m Fiber ST , external 230 50Hz AC power supply, for 0 to 50`C FT14H-Hd = TP to 10Mb m m Fiber ST ...
-
GarrettCom FT14 - page 15
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 8 www Garre t t C om com .. 2.0 INTRODUCTION This section describes the FT14 and FT14H models, including appearance, features and typical applications. 2.1 Inspecting the Package and the Product Examine the shipping container for obvious damage prior to installing this produc ...
-
GarrettCom FT14 - page 16
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 9 www Garre t t C om com .. Remove the Magnum Media Converter from the sh ipping container. Be sure to keep the shipping container should you need to ship the unit at a later date. In the event there are items missing or dam age d contact your supplier. If you need to return ...
-
GarrettCom FT14 - page 17
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 10 www Garre t t C om c om .. The FT14 regular-package units are for office and wiring closet environments and use an external AC power supply. A meta l case with convection cooling is featured. LINK LINK RX/ACT PWR FIBER COPPER P 9VDC .0.3A MP Magnum FT14 onverte 10Mb/s Medi ...
-
GarrettCom FT14 - page 18
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 11 www Garre t t C om com .. Operation may be in 0° to 50°C ambient temp erature. The units can be mounted securely on a closet wall or metal cabinet, or by usi ng the metal panel mounting clips included. The FT14H Hardened unit features a sealed metal case which is also us ...
-
GarrettCom FT14 - page 19
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 12 www Garre t t C om c om .. All units are compatible with Ethernet V 1.0 / 2.0 specifications and comply with IEEE 802.3 standards. Twisted Pair ( 10BASE- Fiber optic - ST Connecto r (10BASE-FL and LINK LINK RX/ACT PWR FIBER COPPER P 9VDC L R X/ A C T Magnum FT14 onverte 10 ...
-
GarrettCom FT14 - page 20
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 13 www Garre t t C om com .. The up-link (or crossover) switch on the RJ-45 por t simplifies cable installation. All fiber models operate in transparent full- or ha lf-duplex mode, supporting matched sets of either mode type, i.e., attached devices ar e either both full-duple ...
-
GarrettCom FT14 - page 21
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 14 www Garre t t C om com .. extended temperature power supply AC/DC (External/Internal) to qualify for un- controlled and Industrial application. Each c onverter features two full sets of LEDs that convey essential diagnostic and st atus information at any angle. See Section ...
-
GarrettCom FT14 - page 22
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 15 www Garre t t C om com .. 2.3 Features and Benefits Reduces Networ k Costs Magnum Media Converters offer the ideal solution to efficiently and inexpensively connect Twisted Pair with 10Mb Fiber media within an expanding Ethernet network where full repeaters are not req ...
-
GarrettCom FT14 - page 23
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 16 www Garre t t C om com .. Two sets of LEDs for viewing status from any angle. Each FT14 Media Converter is equippe d with a two sets (front and side) of LEDs to provide status informa tion when viewed at any angle or mounting arrangement, rack-mount (MC14- Tray) or wal ...
-
GarrettCom FT14 - page 24
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 17 www Garre t t C om com .. Qualifie d to use for temperature un-c ontr olled “outdoor” appli c ati o n The Magnum FT14H Hardened versi on of media converter supports the ambient temperature rating up to –40C to +75C for DC options model, which qualified for un-con ...
-
GarrettCom FT14 - page 25
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 18 www Garre t t C om com .. 2.4 Applications for FT14’s and harde ne d FT14H’s The primary function of a 10Mb Ethernet Media Converter is to permit two different 10Mb media types to coexist ine xpensively within the same network by allowing data to be transmitted and rec ...
-
GarrettCom FT14 - page 26
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 19 www Garre t t C om c om .. In this application, in a Industrial envir onment where extended temp . supported units is a requirement, the existing Twisted pair networ k can be easily connected to longer distance through fiber media using Magnum FT14 or FT14H 10 Mb media con ...
-
GarrettCom FT14 - page 27
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 20 www Garre t t C om com .. 2.5 Full / Half-duplex capability For 10Mb FT14-series Media convert ers, the twisted-pair to fiber combination is capable of full-duplex (i.e., sim ultaneously transmitting and receiving on the same cable segm ent) opera tion. Full-duplex is rare ...
-
GarrettCom FT14 - page 28
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 21 www Garre t t C om c om .. networks, the LINK signal on a managed switch (o r hub) port is used as an indicator that the attached cable segment is installed and operable. The network manager, using the SNMP agent, can troubleshoot the cabling by examining the LINK status o ...
-
GarrettCom FT14 - page 29
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 22 www Garre t t C om c om .. the cable attached to a managed switch port. The Link-Pass-through in the FT14H models provides the LINK “see-through” feature desired for managed networks. On the FT14H models, either both LINK LEDs are lit or neither is lit. And, the FT14 a ...
-
GarrettCom FT14 - page 30
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 23 www Garre t t C om c om .. 3.0 INSTALLATION This section describes the installa tion of the Magnum FT14-series Media Converters, including location, segment distance calculation and media connection. 3.1 Locating the Media Converter U nit Secure attachme n t of mou n ti ng ...
-
GarrettCom FT14 - page 31
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 24 www Garre t t C om com .. Velcro strip may be used for mounting the unit on a vertical surface such as a w all or cabinet, or for securing the unit on a table-top or shelf. Alternatively, metal mounting clips and screws are included for a rugged and secure mounting in any ...
-
GarrettCom FT14 - page 32
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 25 www Garre t t C om c om .. 3.2 MC14-TRAY for Rack Mounting of FT14 and FT14H Media Converter s For 19” rack-mounting of Magnum FT14-series Media Converters, a rack-mount tray is available, MC14-TRAY. The Media Converter units are mounted w ith their RJ-45 port and DC pow ...
-
GarrettCom FT14 - page 33
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 26 www Garre t t C om com .. specific to the “14”-series, a nd do not permit other models). A typical installation of the model MC14-TRAY, 19” rack-mount tray will hold a few (often three to eight) 14-series Media Convert ers, with their power supplies plugged into powe ...
-
GarrettCom FT14 - page 34
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 27 www Garre t t C om c om .. MC14-TR+PS9 and 16 units of Fiber medi a converters for MC14-TR+PS9X2. The MC14-TR+PS9X2 Model has two groups of ei ght units per power s upply. These models are equipped with auto- ranging AC input to the power supplies for use worldwide. (The M ...
-
GarrettCom FT14 - page 35
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 28 www Garre t t C om com .. The side-view picture shown here (above) is an example of an installation of the model MC14-TR+PS9, 19” rack-mount tray, holding a few 10Mbps FT14’s and 100Mb 14E Media Converters, each with their power input plugged into the built-in common A ...
-
GarrettCom FT14 - page 36
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 29 www Garre t t C om c om .. The metal DIN-Rail mounting hardware is optional and needs to be ordered as a separate item, e.g. Model # DIN-RAIL- MC2. It comes with four screws to attach the bracket to the MC unit. The rail clip is spring- loaded with a pull-up latch at the t ...
-
GarrettCom FT14 - page 37
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 30 www Garre t t C om com .. order to maintain optimum network perform ance. (See also Technical Specs, Maximu m Standard Ethernet Segment Distan ces, Section 1.1 of this manual.) When installing the Magnum FT14-series Medi a Converter, it is impor tant to consider the combin ...
-
GarrettCom FT14 - page 38
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 31 www Garre t t C om c om .. Twisted Pair ( 10BASE-T) Y = 55m Fiber optic - ST Connecto r (10BASE-FL and FOIRL) X = 780m LINK LINK RX/ACT PWR FIBER COPPER P 9VDC .0.3A MP GarrettCom Bes t Ethernet at its L = X A L K X = UP LIN R X/ A C T Magnum FT14 onverte 10 Mb/s 10Mb/s Me ...
-
GarrettCom FT14 - page 39
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 32 www Garre t t C om com .. Media Distance Formula for Magnum Media Converters: X% + Y% < 100% Where X = The segment distance on one side of the Magnum Media Converter divided by the Standard Maximum Media Distance for that media type, x 100%. Where Y = The segment length ...
-
GarrettCom FT14 - page 40
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 33 www Garre t t C om com .. allowable distance for UTP 10BASE-T media (100 m) [55/100 x 100% = 55%]. The total of the two percentages (39% + 55%) is 94%, which is allowable. Note 1 : Where more than one media converter is used in one segment run, the percentages for all of t ...
-
GarrettCom FT14 - page 41
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 34 www Garre t t C om com .. 3.6 Connecting Ethern et Media Connecting Ethernet media to the Ma gnum FT14 Series Media Converter is very simple and straightforward. Using pr oper media segment, simp ly attach the cable end to the appropriate connector. See Sections 4.4 for de ...
-
GarrettCom FT14 - page 42
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 35 www Garre t t C om com .. 2. Connect the other end of the cable to the corresponding device. Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the units are powered and proper connections established. If the LINK LED is not illu ...
-
GarrettCom FT14 - page 43
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 36 www Garre t t C om com .. Fiber Cable Type cable diameter * Max. length Wavelength Multi-mode fiber 50/125, 62.5/125. 2km 850 nm Fiber Cable Type cable diameter * Max. length Wavelength Single-mode fiber 2/15 - 8/60 10km 1300 nm * xx/yy are the diameters of the core and th ...
-
GarrettCom FT14 - page 44
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 37 www Garre t t C om com .. 5. The LINK LED corresponding to the fiber port on the front of the product will illuminate (for standard non-Link-Pass- thr ough models ) when a proper connection has been established at both ends (and when power is ON in the units at each end). ...
-
GarrettCom FT14 - page 45
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 38 www Garre t t C om com .. The following data has been collected from component manufacturer’s (HP’s and Siemens’) web sites and catalogs to provide gui dance to network designers and installers. Fiber Port Module Speed, Std. Mode Std. km fdx (hdx) Wave - length nm Ca ...
-
GarrettCom FT14 - page 46
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 39 www Garre t t C om com .. 4.0 OPERATION This section describes the operati on of the Magnum FT14 and FT14H, 10Mb Media Converters, including power supply re quirements, up-link switch functionality, and a description of all LEDs. 4.1 Power Re quirements, Po w er Supply Ty ...
-
GarrettCom FT14 - page 47
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 40 www Garre t t C om c om .. The FT14H Hardened media converters are designed to provide reliable operation, withstand higher temperature environments, a nd provide the direct DC power choices to the user to deploy in uncontro lled temperature environments. 9VDC 24VDC -48VDC ...
-
GarrettCom FT14 - page 48
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 41 www Garre t t C om c om .. Note: When connected to a -48 V centralized dc source these products are to be installed only in Restricted Access Areas ( dedicated equipment rooms, electrical closets or the like). 4.2 Powering the FT14H (DC Direct) with 12V, 24V or –48V DC p ...
-
GarrettCom FT14 - page 49
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 42 www Garre t t C om com .. is also present and optionally can be used with an external AC power supply. DC Power Terminals : “+”, “-”, floating GND : Terminal for “earth” or ground wire connection to the FT14H chassis Input Voltage : 7.5 - 15V DC (9V DC) 18 – ...
-
GarrettCom FT14 - page 50
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 43 www Garre t t C om c om .. 0.2 amp max.(-48V DC) Power Consumpti on : 1.5 watts typical, 2 watts maxm. 4.3 FT14H, DC-powered, -48VDC, 24VDC and 9VDC Installation This section describes the proper connection of the -48VDC leads (or 24VDC, 9VDC leads) to the Direct DC power ...
-
GarrettCom FT14 - page 51
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 44 www Garre t t C om com .. terminals are identified as positive (+) and ne gative (-), and they are floating inside the unit so that either of the terminal may be gr ounded by the user if desired. The chassis is “earth” or ground (GND). The connection procedure is strai ...
-
GarrettCom FT14 - page 52
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 45 www Garre t t C om com .. 4.4 Dual LEDs, front-panel and side -panel (Magnum FT14 and FT14H) LED Description PWR/P Illuminates GREEN to indicate power applied. LINK/L (TP) Illuminates GREEN, S teady ON when both attached cable segments are operational at the other end. LIN ...
-
GarrettCom FT14 - page 53
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 46 www Garre t t C om c om .. 4.5 Up-Link (Cross -over) Switch The FT14 and FT14H Media Converter is equipped with an Up-Link slide switch. When set to the UP position (X), the Media Converter is wired with cross-over functionality for direct up- link to a network hub, switch ...
-
GarrettCom FT14 - page 54
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 47 www Garre t t C om com .. 5.0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments. The installation of Magnum FT14-SERIESs 10 Mb/s Media Converters is a straightforward procedure (se ...
-
GarrettCom FT14 - page 55
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 48 www Garre t t C om com .. 5.1 Before Calling for Assistance 1. If difficulty is encountered when insta lling or operating the unit, refer back to the Installation Section of the applicable chapter of this manual. Also check to make sure that the various compone nts of the ...
-
GarrettCom FT14 - page 56
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 49 www Garre t t C om com .. 4. If the problem is isolated to a network device other than the Magnum FT14/FT14H 10 Mb/s Media Converters product, it is recommended that the problem device is replaced with a known good device. Verify whether or not the problem is corrected. If ...
-
GarrettCom FT14 - page 57
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 50 www Garre t t C om com .. 5.2 When Calling for Assistance Please be prepared to provide the following information. 1. A complete description of the problem, including the following points: a. The nature and duration of the problem; b. Situations when the problem occurs; c. ...
-
GarrettCom FT14 - page 58
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 51 www Garre t t C om com .. 3. It is useful to include other networ k equipment models and related hardware, including personal computers, workstati ons, terminals and pr inters; plus, the various network media ty pes being used. 4. A record of changes that have been made to ...
-
GarrettCom FT14 - page 59
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 52 www Garre t t C om com .. Product name Serial Number (or Invoice Number) Packing List Number (or Sales Order Number) Date of installation Failure sy mptoms, including a full description of the problem. GarrettCom will carefully test and evaluate all returned products, will ...
-
GarrettCom FT14 - page 60
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 53 www Garre t t C om com .. GarrettCom reserves the right to charge for the testing of non-defective units under warranty. Testing and repair of produc t that is not under warranty will result in a customer (user) charge. ...
-
GarrettCom FT14 - page 61
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 54 www Garre t t C om com .. 5.4 Shipping and Packaging Infor mati o n Should you need to ship the unit back to GarrettCom, please follow these instructions: 1. Package the unit carefully. It is recommended that you use the original container if available. Units should be wra ...
-
GarrettCom FT14 - page 62
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 55 www Garre t t C om com .. 4. Ship the package to: GarrettCom, I nc. 47823 Westinghouse Dr. Fremont, CA 94539 Attn.: Customer Service APPENDIX A: WARRANTY INFORMATION GarrettCom, Inc. warrants its products to be free from defects in materials and workmanship for a period of ...
-
GarrettCom FT14 - page 63
FT14 and FT14H 10Mb Media Converters In stallation and User Guide (09/04) 56 www Garre t t C om com .. This warranty will not be effective if, in the opinion of GarrettCom, the product has been damaged by misuse, misapplication, or as a result of service or modification other than by GarrettCom. GarrettCom reserves the right to make a charge for ha ...
Do you have a question concerning GarrettCom FT14?
Use the form below
If you did not solve your problem by using a manual GarrettCom FT14, ask a question using the form below. If a user had a similar problem with GarrettCom FT14 it is likely that he will want to share the way to solve it.