English dropdown-ico

Manual Troy-Bilt CS4210, CS4265

13 pages 2.39 mb
Download

Go to site of 13

Summary
  • Troy-Bilt CS4210, CS4265 - page 1

    Oper ator’ s Man ual Chipper / Shredder Models CS4210 CS4265 IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD LLC P .O . BO X 361131 CL EVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal co mbustion engine and should not be used on or nea r any unimproved forest-covered, brush - covered or grass-covered lan ...

  • Troy-Bilt CS4210, CS4265 - page 2

    2 TABLE OF CONTENTS Content Page Important Safe Op eration Practic es .............. ............. ................ ................ ............. 3 Assembling Your Chippe r Shredder .............. ............. ................ ................ ............. 5 Know Your Chipper Shr edder ..... ................ ................ ............. ...... ...

  • Troy-Bilt CS4210, CS4265 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions whic h, if not followed, could endanger the person al safety and/or property of your self and others. Read and follow all instructions in this manual before atte mpting to operate this machine. Failur e to comply with these instructions ma ...

  • Troy-Bilt CS4210, CS4265 - page 4

    4 i. Never store the machine or fuel containe r inside where th ere is an open flame, spar k, or pilot light (e.g. furn ace, water heater, space heater , clothes dryer, et c.) j. To reduce a fire hazard, keep machine free of grass, le aves, or ot her debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris . k. Allow machine ...

  • Troy-Bilt CS4210, CS4265 - page 5

    5 SAFETY LABELS FOUND ON YOUR UNIT SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER IMPORT ANT: This unit is shipped without gaso line or oil in the engine. Be cer tain to service engine with gasoline and oil as instructed in the Briggs & Stratton Owner/ Operator man ual packed with your unit. before operating you r machine. Loose P arts In Carton ? ...

  • Troy-Bilt CS4210, CS4265 - page 6

    6 Attaching The Debris Collection Bag • To attach the bag, place the opening of the bag completely over the d ischarge chute. • Position the bag so that the wing kno bs which secure the discharge chut e to the impeller housing are completely covered. • Pull on the drawstrap until t he bag is tight aro und discharge ch ute opening. Figure 2 At ...

  • Troy-Bilt CS4210, CS4265 - page 7

    7 Figure 4 SECTION 4: OPERATING YOUR CHIPPER SHREDDER WARNING: The operation of any chipper shredder can result in foreign objects being thrown. Always wear the safety glass es provided with this unit or eye shield s before chipping or shreddin g and while performing any adjustme nts or repairs. Gas And Oil Fill-Up Service the eng ine with gasoline ...

  • Troy-Bilt CS4210, CS4265 - page 8

    8 • Grasp the starte r handle and pull the rope out slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly a llow the rope to recoil. Then pull rope with a r apid, continuous, full arm st roke. Keep a firm grip on starter handle. NOTE: A “clanking” noise may be heard when pulling the starter rope. It is comp ...

  • Troy-Bilt CS4210, CS4265 - page 9

    9 • Use the tamper to assist in feeding branches into the chipper chute. • Apply intermittent pressure (force, in short pulses) while feeding larger (2- 3-inch diam eter) branches into the chipper chute, to avoid bogging or stalling the engine . IMPORT ANT: Never fee d branches with a dia meter greater than thre e (3) inches into the chipper ch ...

  • Troy-Bilt CS4210, CS4265 - page 10

    10 Discharge Chute: Lubrica te the pivot points on the chute deflector wit h light oil once a season. Engine: Refer to the Briggs & Stratton Ow ner/Oper ator manual packed with your unit for lubr ication instructions. Maintenance Engine Refer to the Mainte nance section of the Briggs & Stratton Owner/Opera tor manual packed with your unit. ...

  • Troy-Bilt CS4210, CS4265 - page 11

    11 Figure 9 NOTE: Use a 3/16” hex key (Allen) wrench on t he outside of the blade an d a 1/2” box (or socket) wrench on the inside of the impeller. See Figure 9. Hold the Allen wrench stationary and rot ate the box (or socket) wrench to loosen the nut. • Install a replacemen t blade (Part No. 742-0544) with the hardware r emoved earlier. IMPO ...

  • Troy-Bilt CS4210, CS4265 - page 12

    12 Storing Y our Chipper Shredder • Clean the equipment t horoughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine man ual for cor rect engi ne storage instructions • Store unit in a clean, dry are a. Do not store next to corrosive materials such as fertilizer. SECTION 6: TROUBLESHOOTING NOTE: For repairs beyond t he ...

  • Troy-Bilt CS4210, CS4265 - page 13

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this produc t against defects in material and workmanship for a pe riod of two (2) years commencing on the date ...

Manufacturer Troy-Bilt Category Chipper

Documents that we receive from a manufacturer of a Troy-Bilt CS4210, CS4265 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- CS4210, CS4265 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt CS4210, CS4265
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt CS4210, CS4265.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt CS4210, CS4265, service manual, brief instructions and user manuals Troy-Bilt CS4210, CS4265. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt CS4210, CS4265.

Similar manuals

A complete manual for the device Troy-Bilt CS4210, CS4265, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt CS4210, CS4265 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt CS4210, CS4265.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt CS4210, CS4265 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt CS4210, CS4265, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt CS4210, CS4265, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt CS4210, CS4265 - which should help us in our first steps of using Troy-Bilt CS4210, CS4265
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt CS4210, CS4265
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt CS4210, CS4265 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt CS4210, CS4265?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt CS4210, CS4265, ask a question using the form below. If a user had a similar problem with Troy-Bilt CS4210, CS4265 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)