English dropdown-ico

Manual Audiovox 128-8613

12 pages 0.21 mb
Download

Go to site of 12

Summary
  • Audiovox 128-8613 - page 1

    128-8613 1 of 12 Page 1 Model APS-620N Inst allation Manual This Remote St art System is designed to be used with Automatic T ransmission- Fuel Injection V ehicles Only! COMPONENTS: Control Module 2 Four Button RF T ransmitters Antenna/Receiver 1 1” X 1.75” Foam Pad 6 Pin Main Power Harness 7 Pin Accessory Harness 1 Hood Pin Switch 2 Pin Door L ...

  • Audiovox 128-8613 - page 2

    128-8613 2 of 12 Page 2 INST ALLA TION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location ...

  • Audiovox 128-8613 - page 3

    128-8613 3 of 12 Page 3 the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switch in the hood locations away from wate ...

  • Audiovox 128-8613 - page 4

    128-8613 4 of 12 Page 4 YELLOW W ire: S tarter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from st arting while in gear . Understanding the difference between a me- chanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation ...

  • Audiovox 128-8613 - page 5

    128-8613 5 of 12 Page 5 3 Wire Ground Switched Door Lock Circuits: In this application, the Red wire of the 2 pin harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay . The Green wire of th ...

  • Audiovox 128-8613 - page 6

    128-8613 6 of 12 Page 6 Wiring The 4 Pin Auxiliary Output Harness, Connector “A” The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote S tart unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if th ...

  • Audiovox 128-8613 - page 7

    128-8613 7 of 12 Page 7 2 Pin V alet/Program/Override Push-Button Switch, Connector “D” The Black & Grey twin lead wires loaded in the two pin blue connector are the ground supply and program/valet/override input of the Remote S tart unit. Route the two wires from the previously installed Push-Button switch to the mating connector on the co ...

  • Audiovox 128-8613 - page 8

    128-8613 8 of 12 Page 8 3 Pin Antenna/Receiver , Connector “F” Route the 3 pin connector from the previously installed antenna receiver assemble to the mating connector on the control module. This connector supplies 5 volts, ground and RF data from the antenna receiver to the remote start module. Be certain this connector is firmly seated makin ...

  • Audiovox 128-8613 - page 9

    128-8613 9 of 12 Page 9 T o test this circuit, while the vehicle is running under control of the remote start unit, open the vehicle’s hood. The remote start unit should shut down immediately . If not, check the wiring to the control module and the under hood pin switch. DO NOT RELEASE THE VEHICLE TO THE CONSUMER IF THIS CIRCUIT DOES NOT PERFORM ...

  • Audiovox 128-8613 - page 10

    128-8613 10 of 12 Page 10 The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: B. Additional Ignition Output: C. GM V A TS Key Override: Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm o ...

  • Audiovox 128-8613 - page 11

    128-8613 11 of 12 Page 11 Setting Up The System Programming Features: Bank 1 Transmitter Channels S tart with the system disarmed, turn the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully en ...

  • Audiovox 128-8613 - page 12

    128-8613 12 of 12 Page 12 4 PIN IN VEHICLE DA T A BUS PORT (DBI Port) The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder inter- ...

Manufacturer Audiovox Category Remote Starter

Documents that we receive from a manufacturer of a Audiovox 128-8613 can be divided into several groups. They are, among others:
- Audiovox technical drawings
- 128-8613 manuals
- Audiovox product data sheets
- information booklets
- or energy labels Audiovox 128-8613
All of them are important, but the most important information from the point of view of use of the device are in the user manual Audiovox 128-8613.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Audiovox 128-8613, service manual, brief instructions and user manuals Audiovox 128-8613. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Audiovox 128-8613.

Similar manuals

A complete manual for the device Audiovox 128-8613, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Audiovox 128-8613 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Audiovox 128-8613.

A complete Audiovox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Audiovox 128-8613 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Audiovox 128-8613, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Audiovox 128-8613, that we can find in the current document
3. Tips how to use the basic functions of the device Audiovox 128-8613 - which should help us in our first steps of using Audiovox 128-8613
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Audiovox 128-8613
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Audiovox 128-8613 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Audiovox 128-8613?

Use the form below

If you did not solve your problem by using a manual Audiovox 128-8613, ask a question using the form below. If a user had a similar problem with Audiovox 128-8613 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)