Manual Brinkmann Gas FirePit

40 pages 5.67 mb
Download

Go to site of 40

Summary
  • Brinkmann Gas FirePit - page 1

    OWNER’S MANUAL / MANUAL DEL PROPIET ARIO W ARNING/ADVERTENCIA HAZARDOUS EXPLOSION MA Y RESUL T IF THESE W ARNINGS AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL W ARNINGS AND INSTRUCTIONS IN THIS MANUAL T O A VOID PERSONAL INJUR Y , INCLUDING DEA TH OR PROPERTY DAMAGE. SE PUEDE PRODUCIR UNA EXPLOSIÓN PELIGROSA SI SE HACE CASO OMISO A EST AS A ...

  • Brinkmann Gas FirePit - page 2

    1 WE W ANT YOU T O ASSEMBLE AND USE YOUR FIREPIT AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR FIREPIT . WHEN YOU SEE THE SAFETY ALERT SYMBOL P A Y CLOSE A TTENTION TO THE INFORMA TION WHICH FOLLOWS! READ ALL SAFETY W ARNINGS AND INSTRUCTIONS CAREFULL ...

  • Brinkmann Gas FirePit - page 3

    2 Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Firepit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cylinder Specifications / Cylinder Installation . . . . . . . . . . . . . . . . . . . . . . . 4–7 Leak T esting . . . . . . . ...

  • Brinkmann Gas FirePit - page 4

    3 W ARNING • The installation must conform with local codes or , in the absences of local codes, with the National Fuel Code, ANSI Z223.1. • The appliance, when installed, must be electrically grounded in accordance with local codes or , in the absence of local codes, with The National Electrical Code, ANSI/NFP A70. (If applicable) • Always p ...

  • Brinkmann Gas FirePit - page 5

    4 W ARNING LP GAS CYLINDER (NOT SUPPLIED WITH THIS FIREPIT) The LP cylinder is available for purchase at the same location the firepit was purchased. The LP (Liquid Propane) gas cylinder specifically designed to be used with this firepit must have a 20 lb. (9.1 kg) capacity incorporating a T ype 1 cylinder valve and an over-filling protection devic ...

  • Brinkmann Gas FirePit - page 6

    5 • T urn off the cylinder valve when your firepit is not in use. • Handle the tank with care. • Always secure the cylinder in an upright position. • Never connect an unregulated LP gas cylinder to your firepit. • DO NOT expose LP gas cylinders to excessive heat or ignition sources. • DO NOT store a spare LP gas cylinder under or near y ...

  • Brinkmann Gas FirePit - page 7

    INST ALLING THE LP GAS CYLINDER ONT O THE FIREPIT : 1. Check that the cylinder valve is closed by turning the knob clockwise. 2. Place the cylinder into the tank holder in the bottom of cabinet. 3. Orient the cylinder such that the valve opening faces the center of the firepit, and so that the hose is not kinked or damaged. 4. Fully tighten the cyl ...

  • Brinkmann Gas FirePit - page 8

    7 W ARNING • Never use your firepit without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas firepit must be used. • DO NOT attempt to connect it to any other fuel supply source such as a natural gas line ...

  • Brinkmann Gas FirePit - page 9

    LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the firepit is in use or while firepit is still hot. WHEN TO ...

  • Brinkmann Gas FirePit - page 10

    W ARNING 9 6. Check each place listed (A – K) for growing bubbles which indicates a leak. 7. T urn off gas supply at cylinder valve. 8. T urn on the control knob to release gas pressure in hose. 9. T urn the control knob to "OFF" position. 10. T ighten any leaking connections. 1 1. Repeat soapy water test until no leaks are detected. 12 ...

  • Brinkmann Gas FirePit - page 11

    LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. REMOVE THE FIREPIT COVER before attempting to light the burner so that gas fumes do not accumulate inside the firepit. An explosion could occur if firepit cover is down. 2. Check that the burner control knob and the cylinder valve are turned to the "OFF" position. 3. T urn on the ...

  • Brinkmann Gas FirePit - page 12

    T o obtain the best performance from your firepit, you must perform the following storage and maintenance activities on a regular basis: • Allow at least 35 minutes for the firepit to cool down after use, then disconnect and remove the cylinder . • Cylinder must be stored outdoors in a well-ventilated area out of the reach of children. Disconne ...

  • Brinkmann Gas FirePit - page 13

    12 TROUBLE SHOOTING PROBLEM OBSERVED POSSIBLE CAUSE CORRECTIVE MEASURES Gas leakage Check all gas connections Low gas pressure Check gas supply pressure Clogged or dirty burner ports Clean burner ports-see manual section Bad battery Change battery Incorrect gas supply or pressure Check gas supply pressure Clogged or dirty burner ports Clean burner ...

  • Brinkmann Gas FirePit - page 14

    34 M6 X 14mm Bolts 1 M5 W asher 8 M6 W ashers 4 M4 X 30mm Bolts P ARTS BAG CONTENTS Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process. Y our Parts Bag will include: M6 X 14mm Bolts M5 Nut M4 X 30mm Bolts M4 X 10mm Bolts M6 W ashers M5 W asher AA /1.5V Alkaline Battery 1 M5 Nut 4 ...

  • Brinkmann Gas FirePit - page 15

    FOR FIREPIT W ARRANTY REPLACEMENT P ARTS, PLEASE VISIT US A T : www .grillpartsonline.com ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR FIREPIT . 14 2 1 3 4 5 6 7 8 16 10 9 11 13 12 14 15 WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT . The following to ...

  • Brinkmann Gas FirePit - page 16

    15 Choose a good, cleared assembly area and get a friend to help you to unpack and set up your firepit. CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary . Step 1 Attach the four table panels by using eight M6 x14mm bolts and eight M6 washers. Step 2 Attach the front and back panels to the table assembly by using twel ...

  • Brinkmann Gas FirePit - page 17

    Step 5 Connect the drawer panel with the tank holder support by using four M6 x 14mm bolts. Attach both strengthener supports to the drawer panel and tank holder support by using four M6 x 14mm bolts. Insert cylinder clamp screw as shown. Note: With the help of a friend, turn the cart to its upright position. Step 6 Pull out the sliding tracks on t ...

  • Brinkmann Gas FirePit - page 18

    Step 7 Align tank holder support runners with the sliding tracks on the front and rear panels. Insert runners fully until locked into position. Step 8 Place the burner assembly on the table with the control panel facing the front panel door , attach it by using four M4 x 30mm bolts. 17 ...

  • Brinkmann Gas FirePit - page 19

    18 Step 9 Insert cover handle through firepit cover and secure it to cover by using one M5 washer and M5 nut. Step 10 Place firepit grate directly over burner assembly . Step 1 1 Arrange lava rocks on firepit grate. Step 12 Place firepit cover directly over firepit grate when not in use. Step 13 Unscrew battery compartment cap, located on control p ...

  • Brinkmann Gas FirePit - page 20

    Charmglow ® Rectangular Gas Firepit (Assembled) 19 ...

  • Brinkmann Gas FirePit - page 21

    20 Si la información en este manual no se sigue exactamente, fuego o explosión pueden resultar causando daño de propiedad, heridas personales o pérdida de vida. • No guarde ni use gasolina ni otros líquidos inflamables con vapores en las cercanías de este o de ningún otro artefacto. • ¿QUE HACER SI USTED HUELE GAS? • No trata de encen ...

  • Brinkmann Gas FirePit - page 22

    21 Información Importante de Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Especificaciones para Calentador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Especificaciones / Instalación para Cilindro de propano líquido . . . . . . . 23–26 Pruebas de Detección de Fugas . . . . . . . . . . . . . ...

  • Brinkmann Gas FirePit - page 23

    22 • La instalación debe conformarse con códigos locales o, en ausencia de códigos locales, con el Código Nacional del Combustible, “National Fuel Code, ANSI Z223.1.” • El aparato, cuando instalado, debería estar aterrizado eléctricamente en conformidad con códigos locales o, en ausencia de códigos locales, con El Código Eléctrico ...

  • Brinkmann Gas FirePit - page 24

    23 ESPECIFICACIONES P ARA CALENT ADOR RECT ANGULAR A GAS: Nombre de Producto No. de Modelo Producción de Calor Combustible Suministro de Gas Presión de Colector T amaño de Orificio (diámetro) Presión de Suministro de Gas Rectangular Calentador a Gas 832-7000-S 40,000 BTU/HR Propane-LPG 20 lb. LP-cilindro de gas 1 1 pulgadas por columna de gas ...

  • Brinkmann Gas FirePit - page 25

    24 • Apaga la válvula del cilindro cuando su calentador no está en uso. • Maneja el tanque con el cuidado. • Siempre asegure el cilindro en una posición vertical. • Nunca conecte un cilindro de gas de propano líquido no regulado a su calentador . • Nunca exponga un tanque de gas de propano líquido a fuentes excesivas de calor ni igni ...

  • Brinkmann Gas FirePit - page 26

    25 Abrazadera del Cilindro Portatanque 1. V erifique que la válvula del cilindro está cerrada girando la perilla en sentido horario. 2. Coloque el cilindro en el portatanque en el extremo inferior del gabinete. 3. Sitúe el cilindro de manera que la abertura de la válvula apunte hacia el centro de el calentador y de modo que la manguera no esté ...

  • Brinkmann Gas FirePit - page 27

    26 • Nunca use el calentador sin haber verificado que no hay fugas en las conexiones y mangueras de gas. Consulte los procedimientos apropiados en la sección de "Pruebas de detección de fugas" en este manual. Se debe utilizar el conjunto del regulador de presión y manguera suministrado con el calentador a gas. • NO intente conectar ...

  • Brinkmann Gas FirePit - page 28

    27 PRUEBAS DE DETECCIÓN DE FUGAS: Para impedir los peligros de incendio o explosión: • NO fume ni permita que haya fuentes de encendido en el área mientras realiza la prueba de detección de fugas. • Realice la prueba AL AIRE LIBRE únicamente, en un área bien ventilada. • Nunca realice una prueba para detectar fugas con un cerillo o llam ...

  • Brinkmann Gas FirePit - page 29

    28 6. Inspeccione cada uno de los elementos indicados (A-K) para ver si hay burbujas, lo cual indica una fuga. 7. Cierre el suministro de gas en la válvula del cilindro. 8. Gire las perillas de control para descargar la presión de gas en la manguera. 9. Gire las perillas de control a la posición "OFF" (de apagado). 10. Apriete todas la ...

  • Brinkmann Gas FirePit - page 30

    29 ENCENDIDO DE LA HORNILLA: 1. Abra la tapa para ver el tabla de control. 2. Quite la cubierta antes de encender quemador . 3. Cerciórese que la perilla de control este en la posición "OFF" (apagado). 4. Empuje y gire la perilla de control de la hornilla a la izquierda “IGNITE” (encender). 5. Continúe girando perilla por 30 segund ...

  • Brinkmann Gas FirePit - page 31

    30 Para obtener el mejor uso de su calentador , usted debe realizar las actividades siguientes de almacenamiento y conservación en una base regular: • Permite por lo menos 35 minutos para que el calentador se enfrié después de uso, después desconecte y quite el cilindro. • El Cilindro se debe almacenar fuera en un área bien-ventilado fuera ...

  • Brinkmann Gas FirePit - page 32

    31 Olor de gas Ignición demorada Llama de quemador incorrecta IDENTIFICACIÓN Y CORRECCIÓN DE PROBLEMAS PROBLEMA CAUSAS POSIBLES MEDIDAS CORRECTIV AS Fuga de gas V erifique todas conexiones de gas Suministro bajo de gas Cheque la presión de gas Quemador atascado Limpie quemadores - vea section de manual Batería gastada Cambie a batería El sumi ...

  • Brinkmann Gas FirePit - page 33

    32 34 Pernos M6 X 14mm 1 Arandelas M5 8 Arandelas M6 4 Pernos M4 X 30mm M6 X 14mm Pernos M5 T uerca M4 X 30mm Pernos M4 X 10mm Pernos M6Arandelas M5 Arandelas Bateria Alcalina AA /1.5V 1 T uerca M5 4 Pernos M4 X 10mm 1 Bateria Alcalina AA /1.5V Qty . Qty . CONTENIDO DE LA BOLSA DE P ARTES V erifique que tiene todos los artículos indicados en la LI ...

  • Brinkmann Gas FirePit - page 34

    33 LIST A DE P ARTES: 1 Panel Frontal Lateral 1 Panel Izquierdo Lateral 1 Soporte para Portatanque 2 Reforzado para Soportes 2 Vías Deslizante 1 T ubo de Conexión 1 Bolsa para Pierdas de Lava 1 T ornillo de Abrazadera para el Cilindro 1 Asidero d e Cobertura 1 Cobertura 1 Pierdas de Lava 1 Rejilla de Calentador 1 Asamblaje de Quemador 2 Panel Der ...

  • Brinkmann Gas FirePit - page 35

    34 Elija un lugar adecuado y despejado para armar la parrilla y pídale a un amigo que le ayude. CUIDADO: Algunas partes pueden tener bordes afilados. Póngase guantes de protección si es necesario. Paso 1 Ate los cuatro paneles para la mesa utilizando ocho pernos M6 x14mm y ocho arandelas M6. Paso 2 Ate el panel frontal y trasero al asamblaje de ...

  • Brinkmann Gas FirePit - page 36

    35 Paso 5 Conecte el panel del portatanque con el portatanque utilizando cuatro pernos M 6 x 14mm. Ate el reforzado para soportes así como el panel del potatanque y el portatanque juntos utilizando cuatro pernos M6 x 14mm. Inserte el tornillo de abrazadera para el cilindro como mostrado. Nota: Con la ayuda de un amigo, gire el carrito a su posici? ...

  • Brinkmann Gas FirePit - page 37

    36 Paso 7 Alinee corredores de apoyo del el portatanque con las vías deslizantes en los paneles frontal y trasero. Inserte corredores y métalos completamente hasta que se traben en posición. Paso 8 Coloque el asamblaje del quemador sobre la mesa con el tablero de control frente a la puerta frontal, átelo utilizando cuatro pernos M4 X 30 mm. ...

  • Brinkmann Gas FirePit - page 38

    37 Paso 9 Inserte el asidero de cobertura del calentador y lo asegúrelo a la cobertura del calentador utilizando una arandela M5 y tuerca M5. Paso 10 Coloque la rejilla de calentador directamente sobre asamblaje del quemador . Paso 1 1 Arregle piedras de lava sobre la rejilla de calentador . Paso 12 Coloque la cobertura d e l calentador sobre el c ...

  • Brinkmann Gas FirePit - page 39

    38 Charmglow ® Rectangular Calentador de Fuego a Gas (Armada) ...

  • Brinkmann Gas FirePit - page 40

    140-7000-S 5/07 Owner ’s Manual for Model Manual del Propietario para el Modelo 832-7000-S The Brinkmann Corporation warrants to the original purchaser that the Charmglow ® Rectangular Gas Firepit is free from defects due to workmanship or materials for: Five-year: on stainless steel burners Three-year: on all other stainless steel parts One-yea ...

Manufacturer Brinkmann Category Fire Pit

Documents that we receive from a manufacturer of a Brinkmann Gas FirePit can be divided into several groups. They are, among others:
- Brinkmann technical drawings
- Gas FirePit manuals
- Brinkmann product data sheets
- information booklets
- or energy labels Brinkmann Gas FirePit
All of them are important, but the most important information from the point of view of use of the device are in the user manual Brinkmann Gas FirePit.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Brinkmann Gas FirePit, service manual, brief instructions and user manuals Brinkmann Gas FirePit. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Brinkmann Gas FirePit.

A complete manual for the device Brinkmann Gas FirePit, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Brinkmann Gas FirePit by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Brinkmann Gas FirePit.

A complete Brinkmann manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Brinkmann Gas FirePit - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Brinkmann Gas FirePit, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Brinkmann Gas FirePit, that we can find in the current document
3. Tips how to use the basic functions of the device Brinkmann Gas FirePit - which should help us in our first steps of using Brinkmann Gas FirePit
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Brinkmann Gas FirePit
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Brinkmann Gas FirePit in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Brinkmann Gas FirePit?

Use the form below

If you did not solve your problem by using a manual Brinkmann Gas FirePit, ask a question using the form below. If a user had a similar problem with Brinkmann Gas FirePit it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)