English dropdown-ico

Manual NEC LT 100

52 pages 0.98 mb
Download

Go to site of 52

Summary
  • NEC LT 100 - page 1

    Part No. 78409941 Printed in Japan Ultra-Portable Projector Ultra-Portable Projector Projector User’ s Manual NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 MultiSync ® LT 10 0 ™ NEC Technologies ...

  • NEC LT 100 - page 2

    RF Inter ference W ARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC T echnologies in this manual. F ailure to comply with this government regulation could void your right to operate this equip- ment. This equipment has been tested and found to comply with the limits f ...

  • NEC LT 100 - page 3

    Cleaning 1. Unplug the projector before cleaning. 2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Ne ver use strong deter gents or solvents such as alcohol or thinner . 3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens. Lamp Replacement • Perform lamp repla ...

  • NEC LT 100 - page 4

    Ce symbole a pour but de prévenir l’utilisateur de la présence d’une tension dangereuse, non isolée se trouvant à l’intérieur de l’appareil. Elle est d’une intensité suff isante pour constituer un risque d’électrocution. Eviter le contact avec les pièces à l’intérieur de cet appareil. Ce symbole a pour but de prévenir l’u ...

  • NEC LT 100 - page 5

    4. La fumée, la vapeur et l’exposition aux rayons directs du soleil risquent de détériorer sérieusement les composantes internes. 5. Eviter des manipulations brusques lors du déplacement du projecteur , car un choc violent pourrait endommager les composantes internes. 6. Ne pas deposer d’objets lourds sur le dessus du projecteur . 7. Lors ...

  • NEC LT 100 - page 6

    NEC MultiSync ® Pr ojector Pr oducts NEC T echnolo gies, Inc. (hereafter NECTECH) warr ants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY? Parts and labor are warranted f or (2) two years from the date of the fir st customer purchase. The lamp is warr anted for 1000 hours of op ...

  • NEC LT 100 - page 7

    1. Introduction Introduction T o The MultiSync L T100 Projector ............................................................ 13 How Do Y ou Get Started? ............................................................................................... 15 What ’ s I n The Box? .......................................................................... ...

  • NEC LT 100 - page 8

    This section introduces you to your new MultiSync L T100 (XGA) Projector , provides a list of materials that comes with your projector and describes the features and controls. Congratulations On Your Purchase Of The MultiSync LT100 Projector The MultiSync L T100 is one of the very best projectors av ailable today . The MultiSync L T100 enables you ...

  • NEC LT 100 - page 9

    How Do Y ou Get Started? The fastest way to get star ted is to take your time and do e verything right the first time. T ake a fe w minutes now to click through the training CD-R OM and r evie w the user’ s manual. This may sav e you hours later on. At the beginning of each section of the manual you'll find an o v ervie w . If the section do ...

  • NEC LT 100 - page 10

    Getting T o Know Y our MultiSync L T100 Projector Front Features T op features 17 INTRODUCTION 18 MEMU SELECT ENTER STATUS POWER ON / OFF Monaural Speaker (1W) Remote Sensor Ventilation Lens and lens Cap Focus Ring One-T ouch Tilt Button Adjustable Foot Cooling Fan Rear Features MEMU SELECT ENTER STATUS POWER ON / OFF AC IN Remote Sensor Power Swit ...

  • NEC LT 100 - page 11

    T op Features 1 P ower Button Use this button to turn the po wer on and off when Main Po wer Switch is on and the projector is on standby . 2 Enter Button Executes your menu selection. 3 Select ( ▲▼ § © ) / (+)(–) Buttons Select: After you press the “Menu” button, use the ▲ or ▼ button to select the menu icon of the item you wish to ...

  • NEC LT 100 - page 12

    T erminal Panel Features This panel is located in the side and is where you connect your cables. 1 Remote Control Jac ks a. Remote Contr ol Input Jack Connect your remote control cable here for wired operation. b . Remote Control Output Jack This terminal enables you to operate up to fi ve projectors with the same remote control. When your remote m ...

  • NEC LT 100 - page 13

    5 RGB Output Connector (Mini D-Sub 15 pin) Y ou can use this connector to loop your computer image to an external monitor from the RGB input source. Even if VIDEO is selected, the video image input to the RGB INPUT terminal is output. Audio Output Mini Jack Y ou can use this jack to loop your audio to an external monitor from the VIDEO audio input ...

  • NEC LT 100 - page 14

    Remote Contr ol Features Y ou can use your wireless remote control to operate your MultiSync L T100 Projector . W ith the remote mouse r eceiv er connected to your computer , you can also use the projector’ s remote control to operate your computer . (See pages 51 and 54 to connect the remote mouse receiv er to your computer .) NOTE : If you are ...

  • NEC LT 100 - page 15

    MAGNIFY SLIDE VOLUME POSITION FREEZE PIC-MUTE OFF VIDEO MENU LASER R-CLICK RGB PC CARD S-VIDEO ON POWER + - ++ + -- - 27 11 Laser Button Press and hold this button to acti v ate the laser pointer . When lit, you can use the laser to draw your audience's attention to a red dot that you can place on any object within 30 feet (10 m). 12 Mouse P o ...

  • NEC LT 100 - page 16

    This section describes ho w to set up your MultiSync L T100 projector and how to connect video and audio sources. Setting Up Y our MultiSync L T100 Pr ojector Y our MultiSync L T100 Projector is simple to set up and use. But before you get started, you must f irst: 1. Determine the image size 2. Set up a screen or select a non-glossy white wall ont ...

  • NEC LT 100 - page 17

    31 INST ALLA TION 32 Wide Screen size Projection angle α Screen width H A B Projection distance C D E inch Degree inch mm inch mm inch mm inch mm inch mm inch mm 40” 60” 70” 80” 90” 100” 120” 150” 180” 200” 240” 270” 300” 14.8 14.8 14.7 14.7 14.6 14.6 14.6 14.6 14.5 14.5 14.5 14.5 14.5 32 48 56 64 72 80 96 120 144 160 192 ...

  • NEC LT 100 - page 18

    33 INST ALLA TION 34 Desk top Ceiling mount C A Screen center D E B 3.8” (96.64mm) Projector base α Projector base C α D E B A Unit (inch) H (inch) = Width of screen A = C / cos α B = 3.7H / 25.4 C (WIDE) = (2.026 2 H) – 2.437 C (TELE) = C (WIDE) 2 1.3 D = E / 2 E = H / 4 2 3 Unit (mm) H (inch) = Width of screen A = C / cos α B = 3.7H C (WI ...

  • NEC LT 100 - page 19

    Using A T abletop Or Cart 1. Place your projector on a flat lev el surface at the optimal distance from the screen or wall so you realize the size image you want. (A v oid having bright room lighting or sun light directly on the screen or wall where you'll be projecting the image.) 2. Connect the power cable, remove the lens cap and turn the p ...

  • NEC LT 100 - page 20

    37 INST ALLA TION 38 MEMU SELECT ENTER STATUS POWER ON / OFF AC IN 2 1 Projector Zipper Note book PC Other Accessories T ransporting and storing the projector A padded carrying case has been supplied with your projector . Please use this case when transporting and storing the projector . The carrying case also has a compartment for your laptop comp ...

  • NEC LT 100 - page 21

    W ARNING • Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector s everely damaged. • Do not use the projector where temperatures vary g reatly . The projector must be used at temperatures between 41˚F (5˚C) and 9 5 ˚F (35˚C). • Do not expose the projector to moisture ...

  • NEC LT 100 - page 22

    PC CONTROL VIDEO INPUT RGB INPUT RGB OUTPUT S-VIDEO VIDEO L ( MONO ) - R - AUDIO OUTPUT INTPUT RGB RGB AUDIO AUDIO REMOTE CONTROL Document Camera VCR, Laser Disk Player or DVD Player Wiring Diagram T o video, S-video, and audio inputs on the projector 41 IBM VGA or Compatibles Macintosh or Compatibles (Desk top type) Remote Mouse Receiver PS/2 mous ...

  • NEC LT 100 - page 23

    Connecting Y our PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync L T100 (XGA) Projector will enable you to project your computer's scr een image for an impressi v e presentation. All of these follo wing display standar ds are supported: T o connect to a PC, Macintosh or computer equipped with an XGA/SVGA/VGA ...

  • NEC LT 100 - page 24

    Settings for Monitor Mode Number of DIP switch Monitor size 15” multi-scan mode /16”–13” 17” multi-scan mode /19”–13” 19” multi-scan mode /21”–13” 13” fixed mode /640 2 480 VGA/SVGA mode 16” fixed mode /832 2 624 19” fixed mode /1024 2 768 45 INST ALLA TION 46 S1 ON ON ON ON S2 S3 S4 ON S5 ON ON S6 ON S7 ON S8 ON NOTE ...

  • NEC LT 100 - page 25

    Changing Video Resolutions Depending on your computer's graphic capability , you may be able to select one of sev eral resolutions. Generally a computer- either a PC or Macintosh- with 1 meg. of memory will run: 640 2 480 at 16.7 million colors (24 bit T ruecolor) 800 2 600 at 65 thousand colors. 1024 2 768 at 256 colors. As the resolution inc ...

  • NEC LT 100 - page 26

    Connecting Y our DVD Player Y ou can connect your MultiSync L T100 Projector to a D VD player with the component outputs or V ideo output. T o do so, simply: 1. T urn of f the power to your projector and D VD player . 2. If your D VD player has the component video (Y ,Cb,Cr) output use the optional 15-pin-to-RCA 2 3 cable to connect your D VD playe ...

  • NEC LT 100 - page 27

    Connecting Y our Remote Mouse Receiver The remote mouse receiv er enables you to operate your computer's mouse functions from the NEC MultiSync L T100 remote control. It is a great con venience for clicking through your computer -generated presentations. T o connect the remote mouse r ecei v er: 1. T urn of f your computer . 2. For PCs: Remov ...

  • NEC LT 100 - page 28

    m The Remote Mouse Receiver as a mouse for y our computer INST ALLA TION 53 54 Serial cable (supplied) Serial cable (supplied) Remote cable (supplied) Remote Control Output m The Remote sensors on the pr ojector cabinet w ork as the remote sensor on the Remote Mouse Receiver m Y ou can daisy-chain as man y as five pr ojector s and operate them with ...

  • NEC LT 100 - page 29

    This section describes how to select a computer or video source and how to adjust the picture and sound. General Controls Bef ore you turn on your MultiSync L T100 Projector , ensure that the computer or video source is turned on and that your lens cap is remov ed. 1. T urn On The Projector The main po wer switch is on the back panel of the MultiSy ...

  • NEC LT 100 - page 30

    Using The Menus 1. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu. 2. Press the "Select" button on the projector cabinet or ( ▲ ) ( ▼ ) buttons on your remote control to highlight the menu for the item you want to adjust. 3. Press the "Enter" button on the projector cabi ...

  • NEC LT 100 - page 31

    Enables you to select a video source such as a VCR, D VD player , laser disk player , compu- ter or document camera depending on what is connected to your inputs. Press the "Select" button on the projector cabinet or ( ▲ ) ( ▼ ) buttons on your remote control to highlight the menu for the item you want to adjust. Video Selects device ...

  • NEC LT 100 - page 32

    Image Adjustment Menu 61 OPERA TION 62 Provides access to controls for your image and sound. Use the “Select” b utton on the projector cabinet or ( ▲ ) ( ▼ ) buttons on your remote control to highlight the menu for the item y ou want to adjust. The volume, image mode, brightness, contrast, color , tint, sharpness and white balance controls ...

  • NEC LT 100 - page 33

    63 OPERA TION 64 Brightness Use the “ Adjust” (+) or (–) b uttons to adjust the br ightness. Contrast Use the “ Adjust” (+) or (–) b uttons to adjust the contrast. Color* Use the “ Adjust” (+) or (–) b uttons to adjust the color. Tint* Use the “ Adjust” (+) or (–) b uttons to adjust the tint. Sharpness* Use the “ Adjust” ...

  • NEC LT 100 - page 34

    Provides access to Lamp Usage information, the Auto Start, Po wer Management and On- screen Mute features. Use the “Select” button on the projector cabinet or ( ▲ ) ( ▼ ) b uttons on your remote control to access a submenu. T hen press “ Adjust” (+) or (–) to choose a specific option. Lamp Usage This tells you how long the lamp has be ...

  • NEC LT 100 - page 35

    Settings Menu Enables you to set preferences and other operating options. Use the “Select” button on the projector cabinet or ( ▲ ) ( ▼ ) buttons on your remote control to access the submenu you w ant. Custom Memory This enables you to sa ve your current settings for an RGB source in one of fi ve memories, Custom 1-5. T o c hange the ST AND ...

  • NEC LT 100 - page 36

    Using the V iewer function If you use the V ie wer function on the projector , you must first install the optional L T V ie wer board (VK-L T) in the projector and set up the exclusi ve software included with the VK-L T kit. See the user's manual included with the VK-L T for installing and uninstalling the software. Mounting the Optional L T V ...

  • NEC LT 100 - page 37

    Projecting Slides Orientation of flash memory card insertion The flash memory card has a front and a back side and the flash memory card is designed to be inserted in only one orientation. The card is designed so that it cannot be inserted in rev erse. T rying to force the card into slot may result in damage to the card and the PCMCIA card slot. Se ...

  • NEC LT 100 - page 38

    Selecting a File from a List of Files * The V ie w er feature allo ws you to store one or more presentation materials in a single flash memory card. Each material is referred to as a "file" or "slide". T o select a file from a list of files 1. Press the Menu b utton on the remote control or cabinet to select "PC Card". ...

  • NEC LT 100 - page 39

    Switching Slides T o switc h slides, press "SLIDE +" or "SLIDE –" button. T his will cancel the Auto Play mode. T o set the Auto Play mode, press the Menu button to select “Start” from the Source menu and press the Enter button on the cabinet or the Left Click b utton on the remote control. This is valid only w hen the Aut ...

  • NEC LT 100 - page 40

    This section describes the simple maintenance procedures you should follow to replace the lamp and replace the batteries in the remote control. Replacing The Lamp After your lamp has been operating for 1000 hours or longer , the “sta- tus” light in the cabinet will turn red. Even though the lamp may still be working, replace it at 1000 hours to ...

  • NEC LT 100 - page 41

    79 Remote Contr ol Batter y Installation 1. Press firmly and slide the ba ttery cov er off. 2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries' polarity (+/–) aligned correctly . 3. Slip the cover back over the batteries until it snaps into place. MAINTENANCE 80 Operating Range Range of 360˚ and a dis ...

  • NEC LT 100 - page 42

    Etape 3 Etape 4 Etape 5 81 Cette section décrit les procédures simples d’entretien que vous aurez à suivre pour remplacer la lampe et remplacer les piles de la télécommande. Remplacement de la lampe Lorsque la lampe a été utilisée pendant 1000 heures ou plus, le voyant “Status” (état) du coffret s’allume. Même si la lampe peut enc ...

  • NEC LT 100 - page 43

    83 MAINTENANCE 84 Installation des piles de la télécommande 1. Appuyez fermement et retirez le couvercle des piles en le f aisant glisser . 2. Retirez les deux piles usagées et installez de nouvelles piles (AA). Assurez-v ous de respecter la polarité (+/–) des piles. 3. Remettez le couvercle des piles en le f aisant glisser, jusqu’à ce qu? ...

  • NEC LT 100 - page 44

    This section helps you resolv e problems you may encounter while setting up or using your MultiSync L T100 Projector . Status Light Messages TROUBLESHOOTING 5 85 Status m Normal m The projector lamp has exceeded 1000 hours of operation and should be replaced. m The lamp housing is not correctly installed. Install it correctly . • The temperature ...

  • NEC LT 100 - page 45

    Common Pr oblems & Solutions Problem Does not turn on No picture Image isn’t square to the screen Picture is blurred Check These Items • Check that the power cable is plugged in and that the power switch on the back panel is on. • Ensure that the lamp cover and lamp housing are installed correctly. (See page 77.) • Check the status ligh ...

  • NEC LT 100 - page 46

    This section pro vides technical information about the MultiSync L T100 Projector's performance. Optical DMD TM Single Chip Digital Micromirror De vice(DMD TM ), 1024 2 768 dots Lens Manual zoom, manual focus F 2.44 f =26-30 mm Lamp Metal halide lamp 280 W Image Size 610-7620 mm (24-300 inches) diagonal Projection Distance 1.2 – 12.3m Contra ...

  • NEC LT 100 - page 47

    Cabinet Dimensions 91 Unit : inch (mm) SPECIFICA TIONS 92 12.6" (320) 9.8" (250) 3.8" (97) 0.79" (20) 5.6" (142) 4.5" (114) 0.7" (19) 3.3" (83) Lens center ...

  • NEC LT 100 - page 48

    D-Sub Pin Assignments PC 15-Pin mini D-Sub Pin No . Signal to be connected 1 Red 2 Green 3 Blue 4 GND 5 GND 6 Red GND 7 Green GND 8 Blue GND 9 No Connection 10 Digital GND 11 GND 12 No Connection 13 Horizontal Sync 14 V ertical Sync 15 No Connection 1 2 3 4 5 11 12 13 14 15 6 7 8 9 10 PC 15-Pin mini D-Sub 93 SPECIFICA TIONS 94 ...

  • NEC LT 100 - page 49

    Timing Chart 95 SPECIFICA TIONS 96 Y/N Signal Resolution Refresh F .H. Dot Rate (Hz) (kHz) Clk(MHz) Y NTSC 640 2 480 60 15.734 - Y P AL 768 2 576 50 15.625 - Y SECAM 768 2 576 50 15.625 - Y VESA 640 2 350 85.08 37.86 31.5 Y IBM 640 2 400 70 31.47 25.175 Y VESA 640 2 400 85.08 37.86 31.5 Y MA C 640 2 400 66 35 30.24 Y VESA 640 2 480 59.94 31.47 25.1 ...

  • NEC LT 100 - page 50

    97 01 V ideo 03H No Same as remote 02 RGB 04H No Same as remote 03 S-V ideo C6H No Same as remote 04 PC CARD 27H No Same as remote (av ailable only when V ie wer kit is connected to) 05 Power On 08H No Same as remote 06 Power Of f 14H No Same as remote 07 Picture Mute 47H No Same as remote 08 Audio Mute 45H No 09 Onscreen Mute 11H No 10 Reset 43H N ...

  • NEC LT 100 - page 51

    Command Codes (continued) No. Function Code Data Description 99 SPECIFICA TIONS 100 32 Display Mode Select 1FH Y es 0 Normal Aspect 1 W ide Aspect 33 Pow er Management On 15H No 34 Pow er Management Off 16H No 35 Digital Zoom W 89H No Same as remote 36 Digital Zoom T 8AH No Same as remote 37 Brightness 60H Y es 0 (00H) –– 63 (3FH) 38 Contrast 6 ...

  • NEC LT 100 - page 52

    Cable Connection Communication Pr otocol Baud rate: 9600 bps Data length: 8 bits Parity: No parity Stop bit: One bit X on/off: None Communications Full duplex procedur e: If the CPU of the projector has recei ved the data correctly , it returns an A CK(C5H). If the receiv ed da ta is not correct, the CPU returns a NAK(CAH), then the following statu ...

Manufacturer NEC Category Projector

Documents that we receive from a manufacturer of a NEC LT 100 can be divided into several groups. They are, among others:
- NEC technical drawings
- LT 100 manuals
- NEC product data sheets
- information booklets
- or energy labels NEC LT 100
All of them are important, but the most important information from the point of view of use of the device are in the user manual NEC LT 100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NEC LT 100, service manual, brief instructions and user manuals NEC LT 100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NEC LT 100.

Similar manuals

A complete manual for the device NEC LT 100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NEC LT 100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NEC LT 100.

A complete NEC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NEC LT 100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NEC LT 100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NEC LT 100, that we can find in the current document
3. Tips how to use the basic functions of the device NEC LT 100 - which should help us in our first steps of using NEC LT 100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NEC LT 100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NEC LT 100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NEC LT 100?

Use the form below

If you did not solve your problem by using a manual NEC LT 100, ask a question using the form below. If a user had a similar problem with NEC LT 100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)