English dropdown-ico

Manual Star Micronics SP312F

26 pages 0.24 mb
Download

Go to site of 26

Summary
  • Star Micronics SP312F - page 1

    DOT MA TRIX PRINTER SP312F SP342F-A MANUALE DI ISTRUZIONI ...

  • Star Micronics SP312F - page 2

    Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ...

  • Star Micronics SP312F - page 3

    – 37 – INDICE 1. CARICAMENTO DELLA CARTUCCIA DEL NASTRO .............. 38 1-1. SP312 ......................................................................................... 38 1-2. SP342 ......................................................................................... 39 2. CARICAMENTO DELLA CARTA ..................................... ...

  • Star Micronics SP312F - page 4

    – 38 – 1. CARICAMENTO DELLA CARTUCCIA DEL NASTRO Fig. 1-1 Rimozione del coperchio anteriore (SP312) Fig. 1-2 Caricamento della cartuccia del nastro (SP312) 1 Regolare l’interruttore di alimenta- zione della stampante sulla posizio- ne di spegnimento. 2 Per rimuovere il coperchio anterio- re sollevarlo di circa 3 cm e tirarlo in avanti. NOTA: ...

  • Star Micronics SP312F - page 5

    – 39 – 1-2. SP342 Fig. 1-3 Rimozione del coperchio anteriore (SP342) Fig. 1-4 Sollevare la taglierina automatica e rimuovere il materiale di imballaggio (SP342) 1 Regolare l’interruttore di alimenta- zione della stampante sulla posizio- ne di spegnimento. 2 Per rimuovere il coperchio anterio- re sollevarlo di circa 3 cm e tirarlo in avanti. N ...

  • Star Micronics SP312F - page 6

    – 40 – 4 Per eliminare allentamenti del na- stro girare la manopola di avanza- mento del nastro sulla cartuccia del nastro in direzione della freccia. 5 Allineare la guida della cartuccia del nastro con la parte incassata del telaio. Inserire la cartuccia del na- stro da quella posizione fino a quan- do si sente uno scatto. Inserire il nastro i ...

  • Star Micronics SP312F - page 7

    – 41 – 2. CARICAMENTO DELLA CART A 2-1. SP312 Fig. 2-2 Montaggio dei supporti per carta in rotolo (SP312) Fig. 2-1 Rimozione del coperchio posteriore (SP312) Interruttori DIP 1 Regolare l’interruttore di alimenta- zione della stampante sulla posizio- ne di spegnimento. 2 Regolare l’interruttore DIP 2-4 in base alla larghezza della carta usa ...

  • Star Micronics SP312F - page 8

    – 42 – 5 Regolare le guide della carta sini- stra e destra. Lasciare uno spazio di 0,5 mm tra la guida della carta e il bordo della carta e fissare la leva di blocco. • Quando si inserisce l’anello di fermo corrispondente alla scana- latura sull’asta delle guide della carta mostrata nella Fig. 2-3, quella sarà la posizione quando si fiss ...

  • Star Micronics SP312F - page 9

    – 43 – 2-2. SP342 1 Regolare l’interruttore di alimenta- zione della stampante sulla posizio- ne di spegnimento. 2 Per rimuovere il coperchio anterio- re sollevarlo di circa 3 cm e tirarlo in avanti. NOTA: Non toccare la testina di stampa subito dopo la stampa perché può essere molto calda. 3 Per rimuovere il coperchio poste- riore sollevar ...

  • Star Micronics SP312F - page 10

    – 44 – A: Un foglio di carta (posizione standard) B: Carta carbone Fig. 2-6 Posizione della leva di regolazione (SP342) Fig. 2-8 Guida della carta in rotolo (SP342) Fig. 2-9 Sollevare la taglierina automatica (SP342) Fig. 2-7 Montaggio dei supporti carta in rotolo (SP342) 5 Regolare le guide della carta sini- stra e destra. Lasciare uno spazio ...

  • Star Micronics SP312F - page 11

    – 45 – 7 Regolare l’interruttore di alimenta- zione della stampante sulla posizio- ne di accensione. 8 Tagliare la parte iniziale della carta in rotolo su una linea diritta. • Se la parte iniziale della carta è fissata con un’etichetta, ecc., ri- muovere la parte adesiva dell’eti- chetta. Se rimane dell’adesivo sulla carta, si può a ...

  • Star Micronics SP312F - page 12

    – 46 – Fig. 2-12 Inserimento della carta nella taglierina automatica (quando si usa carta carbone) (SP342) C Tirare il bordo della carta per ri- muovere eventuali allentamenti e quindi abbassare la taglierina auto- matica. D Inserire la carta attraverso l’uscita carta sul coperchio anteriore e quin- di rimettere il coperchio anteriore eseguen ...

  • Star Micronics SP312F - page 13

    – 47 – 3. P ANNELLO DI CONTROLLO POWER ALARM ON LINE FEED 3 4 5 1 2 1 Interruttore “ON LINE” Alterna lo stato dello stampante tra “ON LINE” e “OFF LINE”. Quan- do la stampante alterna tra “ON LINE” e “OFF LINE”, il cicalino emette un breve segnale acustico. (la commutazione “ON LINE” e “OFF LINE” è possibile solo qu ...

  • Star Micronics SP312F - page 14

    – 48 – ...

  • Star Micronics SP312F - page 15

    – 49 – Serial interface connector APPENDIX Connectors and Signals (Serial Interface) RS-232C Pin no. Signal name I/O Function direction 1 F-GND — Frame ground 2 TXD OUT Transmitted data 3 RXD IN Received data 4 RTS OUT Data transmission request signal. This is always “SPACE” when the printer is turned on. 5 CTS IN This signal changes to ? ...

  • Star Micronics SP312F - page 16

    – 50 – APPENDIX 20 mA current loop (option) Pin no. Signal name I/O Function direction 9 TTY TXDR — Indicates the ground side of the data signal of 20 mA loop current. 10 TTY TXD OUT Transmitted data of 20 mA current loop. 17 TTY TXDR — Indicates the ground side of the data signal of 20 mA loop current. 18 TTY RXDR — Indicates the ground ...

  • Star Micronics SP312F - page 17

    – 51 – Interface Connections (Serial Intefface) The following is a basic example of interface connections. (For interface connections, refer to the specifications for the respective interface.) An IBM PC type serial port is shown in below. Example of interface connections for an IBM PC APPENDIX ...

  • Star Micronics SP312F - page 18

    – 52 – Connectors and Signals (Parallel Interface) Pin No. Signal IN/OUT Function Name 1 STROBE IN Signals when data is ready to be read. Signal goes from HIGH to LOW (for at least 0.5 microsec.) when the data is available. 2-9 DATA1-8 IN These signals provide the information of the first to eighth bits of parallel data. Each signal is at HIGH ...

  • Star Micronics SP312F - page 19

    – 53 – Peripheral Unit Drive Circuit [Drive output 24V, max. 1.0 A] Drive circuit APPENDIX ...

  • Star Micronics SP312F - page 20

    – 54 – General Specifications Printing method: Serial impact dot matrix Print direction: Bi-directional Number of head pins: 9 wires Number of print columns: 40 columns, 15 CPI 33 columns, 12 CPI 22 columns, 8 CPI Character set: ASCII 96 (characters) Special characters 64 Block graphics 64 IBM special characters 64 IBM block graphics 50 KATAKAN ...

  • Star Micronics SP312F - page 21

    – 55 – Print speed: Approx. 3.2 lines per sec. Line spacing: 1/6-inch (initial setting), 1/8-inch, 1/12-inch, n /72-inch Paper feed method: Friction feed Paper feed speed: Approx. 3 inches/sec. Paper specifications Paper type: Ordinary bond and carbonless copy paper Paper width: 82.5 ± 0.5 mm (3.25 inches) 76 ± 0.5 mm (3.0 inches) 57.5 ± 0.5 ...

  • Star Micronics SP312F - page 22

    – 56 – AC power cable: Approx. 155 cm long Power consumption: Max. 60 W Avg. 30 W (During continuous printing of ASCII characters) Ambient temperature/humidity Operating temperature: 0 ° C to +50 ° C Operating humidity: 10 % to 90 % RH (without condensation) Storage temperature: –20 ° C to +70 ° C Storage humidity: 5 % to 95 % RH (at 40 ? ...

  • Star Micronics SP312F - page 23

    – 57 – Overall dimensions (mm) (SP342) 169 W × 330 D × 176 H (mm) Approx 4.5 kg APPENDIX ...

  • Star Micronics SP312F - page 24

    – 64 – MEMO ...

  • Star Micronics SP312F - page 25

    ...

  • Star Micronics SP312F - page 26

    Printed in Japan, 80870015 HEAD OFFICE STAR MICRONICS CO., LTD. 20-10 Nakayoshida, Shizuoka, 422 Japan Tel: (054) 263-1115, Telefax: (054) 263-8714 OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC. 70-D Ethel Road West, Piscataway, NJ 08854 U.S.A Tel: (908) 572-9512, Telefax: (908) 572-5095, Telex: 299766 STAR UR STAR MICRONICS DEUTSCHLAND ...

Manufacturer Star Micronics Category Printer

Documents that we receive from a manufacturer of a Star Micronics SP312F can be divided into several groups. They are, among others:
- Star Micronics technical drawings
- SP312F manuals
- Star Micronics product data sheets
- information booklets
- or energy labels Star Micronics SP312F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Star Micronics SP312F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Star Micronics SP312F, service manual, brief instructions and user manuals Star Micronics SP312F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Star Micronics SP312F.

Similar manuals

A complete manual for the device Star Micronics SP312F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Star Micronics SP312F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Star Micronics SP312F.

A complete Star Micronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Star Micronics SP312F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Star Micronics SP312F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Star Micronics SP312F, that we can find in the current document
3. Tips how to use the basic functions of the device Star Micronics SP312F - which should help us in our first steps of using Star Micronics SP312F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Star Micronics SP312F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Star Micronics SP312F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Star Micronics SP312F?

Use the form below

If you did not solve your problem by using a manual Star Micronics SP312F, ask a question using the form below. If a user had a similar problem with Star Micronics SP312F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)