English dropdown-ico

Manual Hand Held Products 5700

100 pages 0.91 mb
Download

Go to site of 100

Summary
  • Hand Held Products 5700 - page 1

    Decoded Output ...

  • Hand Held Products 5700 - page 2

    Disclaimer W elch Allyn  reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult W elch Allyn to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of W elc ...

  • Hand Held Products 5700 - page 3

    SCANTEAM 5700 User ’s Guide CDRH Statement This product complies with 21 CFR Part 1040. This product is a Class II (Class IIIa for 5700ALR) laser product with a maximum output of 1.0 mW (1.5 mW for 5700ALR) at 650 nanometers and continuous wave. This equipment does not exceed the Class B limits for radio noise emissions as described in the Radio ...

  • Hand Held Products 5700 - page 4

    SCANTEAM 5700 User’s Guide The SCANTEAM 5700 product is covered by one or more of the following U.S. Patents: 4,360,798; 4,369,361; 4,387,297; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,816,660; 4,845,350; 4,896,026; 4,923,281; 4,992,717; 5,017,765; 5,047,617; 5,1 13,445; 5,140,144; 5,149,950; 5,168,148; 5,168, ...

  • Hand Held Products 5700 - page 5

    i SCANTEAM 5700 User’s Guide T ABLE OF CONTENTS Section 1 Introduction & Quick Start Menu Section Page Introduction 1–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scanner Identification 1–2 . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Scanner 1–3 . . . . . . . . . . . . . . . . . . . . . ...

  • Hand Held Products 5700 - page 6

    ii SCANTEAM 5700 User’s Guide Section 2 Output Parameters Menu, continued Output Selections Beeper V olume Selection 2–8 . . . . . . . . . . . . . . . . . . . . . . . Output Delays Selection 2–8 . . . . . . . . . . . . . . . . . . . . . . . . Reread Delay Selection 2–9 . . . . . . . . . . . . . . . . . . . . . . . . . Good Read Delay Select ...

  • Hand Held Products 5700 - page 7

    iii SCANTEAM 5700 User’s Guide Section 4 Symbology Menu Section Page Industrial Symbology Selections Introduction 4–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Codabar Selection 4–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 39 Selection 4–4 . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Hand Held Products 5700 - page 8

    iv SCANTEAM 5700 User’s Guide Section 8 Maintenance and T roubleshooting Section Page Maintenance 8–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T roubleshooting 8–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 9 Customer Service Section Page Obtaining Factory Service 9–1 . . . . . . . . . . ...

  • Hand Held Products 5700 - page 9

    1–1 SCANTEAM 5700 User’s Guide The scanner recognizes and decodes 14 industry-standard bar code symbologies. Y our scanner provides high value performance in an economical, durable solution for a wide variety of bar code data collection applications. The scanner contains Welch Allyn’ s Instant Interface module, which integrates aggressive (? ...

  • Hand Held Products 5700 - page 10

    SCANTEAM 5700 User’s Guide 1–2 SCANTEAM 5700 Identification Label Interface Option Option IBM 4683 OCIA OCR Bar Image Laser Out W and Emulation TTL RS–232 T rue RS–232 Keyboard Wedge 0* 1 2 3 4** DD D D D D D D D D D V arious V arious DEC Only RS–232 Wedge D ➌ ➋ ➌ ➊ Model Number 5X00/A–12 Scanner Identification AutoT rigger Opti ...

  • Hand Held Products 5700 - page 11

    1–3 SCANTEAM 5700 User’s Guide Connecting the Scanner Install the scanner by following the steps shown below: ➊ T urn off the power to the host system. ➋ Connect the interface cable to the scanner and to the terminal/computer . Keyboard Wedge Interface Example Disconnect 1 2 3 ➌ T urn on the power to the host system. ➍ Program your scan ...

  • Hand Held Products 5700 - page 12

    SCANTEAM 5700 User ’s Guide 1–4 In. T ypical Depth of Field in Inches/Centimeters Cm. 0 0 2 5.08 4 10.2 6 15.2 8 20.3 10 25.4 12 30.5 14 35.6. 16 40.6 18 45.7 20 50.8 22 55.9 24 61 26 66 28 71.1 30 76.2 32 81.3 In. Cm. 9.65 24.51 1 9.65 24.51 1 5 mil 2.5 3.5 7.5 mil 2 7 20mil 1.5 18 40 mil 3.5 26 55 mil 4 31 19.3” T ypical Performance at 20 ? ...

  • Hand Held Products 5700 - page 13

    1–5 SCANTEAM 5700 User’s Guide In. Cm. 2 5.08 2 5.08 1 2.54 00 1 2.54 2.0” 3” 3 mil 1.0 2.5 .5 5 mil 7.5 mil 4.0 4.5 In. T ypical Depth of Field in Inches/Centimeters Cm. 0 0 1 2.54 2 5.08 3 7.62 4 10.16 5 12.7 6 15.24 T ypical Performance at 20 ° C for SCANTEAM 5700/HD 2.8” 13 mil 6.0 .5 1.0 10 mil 5.5 .5 ...

  • Hand Held Products 5700 - page 14

    SCANTEAM 5700 User’s Guide 1–6 In. Cm. 41 15 mil 25 88 55 mil In. T ypical Depth of Field in Inches/Centimeters Cm. 0 90 180 270 360 T ypical Performance at 20 ° C for SCANTEAM 5700ALR 100 mil 322 123 30 104.1 20 76.2 10 50.8 25.4 00 25.4 10 50.8 20 76.2 30 104.1 41 30 mil 43 22 99 40 70 mil retroreflective – 68” (172.7 cm) – 13.5’ (41 ...

  • Hand Held Products 5700 - page 15

    1–7 SCANTEAM 5700 User’s Guide IBM PC A T and Compatibles Interface (Default) IBM PC, W and Emulation Inter face IBM PS/2 and Compatibles Interface IBM PC XT and Compatibles Interface These bar codes also program a carriage return (CR) suffix. (also PS/2 30-286, 50, 55SX, 60, 70, 70-061, 70-121, 80) ( for PS/2 25, 30 models) W and Emulation (Co ...

  • Hand Held Products 5700 - page 16

    SCANTEAM 5700 User’s Guide 1–8 IBM 4683 Port 5B Interface IBM 4683 Inter face IBM 4683 Port 9B HHBCR–1 Interface IBM 4683 Port 9B HHBCR–2 Interface IBM 4683 Port 17 Interface EAN 8 0C Code 39 00 0A 0B EAN 13 16 I 2 of 5 00 0D 0B UPC A 0D Code 128 00 18 0B UPC E 0A Symbology Suffix Symbology Prefix These bar codes also program the following ...

  • Hand Held Products 5700 - page 17

    1–9 SCANTEAM 5700 User’s Guide The bar code above also programs the following parameters: Spectra-Physics OCIA Interface OCIA Inter face NCR OCIA Short Form Format (Eight Bit) Interface NCR OCIA Long Form Format (Nine Bit) Interface EAN 8 06 06 UPC A 01 EAN 13 06 UPC E 05 Symbology Suffix Symbology Prefix EAN 8 0F 0F UPC A 0A EAN 13 0F UPC E 0E ...

  • Hand Held Products 5700 - page 18

    SCANTEAM 5700 User ’s Guide 1–10 The bar code above also programs the following parameters: EAN 8 0C UPC A 0D EAN 13 16 UPC E 0A Code 128 1D EAN 8 17 UPC A 17 EAN 13 17 UPC E 17 I 2 of 5 03 ( Application Dependent ) Fujitsu OCR Interface OCR, RS232 Inter face IBM OCR (Port 21) Interface Symbology Suffix Symbology Prefix Symbology Suffix Symbolo ...

  • Hand Held Products 5700 - page 19

    1–1 1 SCANTEAM 5700 User’s Guide Supported T er minals T erminal Model(s) T erminal I.D. ADI 1496 72 Apple Desktop Bus ADB MAC Classic, SE SE30, II (All) 49 Bull BDS–7 (HDS–7) 35 Burroughs B25 75 Decision Data DDC3596, 3597 30 DEC VT–220, 320, 330, 340 420 04 Esprit 200, 400 05 Falco 5220 47 Heath Zenith PC 90 HP 700/44, 700/92, 700/94, 2 ...

  • Hand Held Products 5700 - page 20

    SCANTEAM 5700 User’s Guide 1–12 Supported T er minals T erminal Model(s) T erminal I.D. ICL 300 77 IDEAS 08 ITT 9271 07 Lee Data IIS 07 Link MC–5 18 Mac 49 OCIA 52 OCR 53 Olivetti M19, M24, M28, M200 01 Olivetti 240, 250, 290, 380, P500 03 Qume ANSI QVT 61, 62, 70, 191, 321, 322 82 Qume ASCII QVT 31, 51, 61, 62, 70, 191 74 Qume Enhanced PC QV ...

  • Hand Held Products 5700 - page 21

    1–13 SCANTEAM 5700 User’s Guide Show Software Revision Factory Default Settings Reset Factory Settings Status Check Program Carriage Return Suffix Quick Suffix Selections Clear Bar Code Suffix Scanning the Factory Default Settings bar code resets the scanner to the original factory settings, clearing any programming changes you may have made. I ...

  • Hand Held Products 5700 - page 22

    SCANTEAM 5700 User’s Guide 1–14 Scanner models 5700–X1 and 5700/X–X2 support the dual interface option allowing you to connect to two different terminals by switching interface cables. This option supports interfaces common to portable data terminals. T o program the scanner for secondary interface, follow the steps below . (Dual Interface ...

  • Hand Held Products 5700 - page 23

    1–15 SCANTEAM 5700 User’s Guide Same Code W and Emulation Selection [ ✱ Code 39 W and Emulation Selection Code 39 W and Emulation Selection Same Code W and Emulation Selection RS-232 Selection RS-232 Selection Laser Emulation Selection Laser Emulation Selection [ Supports Code 39, UPC, EAN, Code 128, Interleaved 2 of 5, and Codabar . All othe ...

  • Hand Held Products 5700 - page 24

    SCANTEAM 5700 User’s Guide 1–16 Dual Inter face Enable/Disable Selection Power Up Delay Laser Emulation Power Up Delay Selection Switched Power Mode Selections ✱ Switched Power (Low Power) Mode Enable ✱ Disable Constant Power Mode Dual Interface Disable Selection lets you temporarily disable the dual interface selection, while retaining you ...

  • Hand Held Products 5700 - page 25

    2–1 SCANTEAM 5700 User’s Guide Introduction Use this chapter to program the output parameters for the Hand-Held Laser Scanner . This programming section contains the following menuing selections: • Prefix and Suffix • Output • Serial Communication (RS-232) • Data Formatter Section 2 Serial Inter face Menu ...

  • Hand Held Products 5700 - page 26

    2–2 SCANTEAM 5700 User ’s Guide Primary Inter face Prefix and Suffix The scanner transmits a decoded message after every successful bar code read. Prefix and Suffix characters are data characters you may assign to be sent before and after the transmitted bar code data. Transmitted data frame –> Prefix Suffix Bar Code Message Programming St ...

  • Hand Held Products 5700 - page 27

    2–3 SCANTEAM 5700 User’s Guide Add Primary Prefix ] Clear All Primary Prefixes Add Primary Suffix ] Primary Inter face Prefix Selection Primary Inter face Suffix Selection Exit Selection for Prefix / Suffix Discard Current Prefix or Suffix Changes Clear All Primary Suffixes ] One or more two-digit numbers are required after scanning this progra ...

  • Hand Held Products 5700 - page 28

    2–4 SCANTEAM 5700 User’s Guide Secondary (Dual) Inter face Prefix and Suf fix The scanner will transmit a decoded message after every successful bar code read. Prefix and Suffix characters are data characters you may assign to be sent before and after the transmitted bar code data. Transmitted data frame –> Prefix Suffix Bar Code Message P ...

  • Hand Held Products 5700 - page 29

    2–5 SCANTEAM 5700 User’s Guide Add Secondary Prefix ] Clear All Secondary Prefixes Add Secondary Suffix ] Secondary Inter face Prefix Selection Secondary Inter face Suffix Selection Exit Selection for Prefix / Suffix Discard Current Prefix or Suffix Changes Clear All Secondary Suffixes ] One or more two-digit numbers are required after scanning ...

  • Hand Held Products 5700 - page 30

    2–6 SCANTEAM 5700 User’s Guide Example 1: Add Suffix for Specific Symbology Y ou want to send a CR (carriage return) Suffix for UPC only . Prefix and Suf fix Examples H Scan the Add Suffix Suf fix Selection bar code. H The Symbology Chart indicates that the Hex value of UPC is “63”. Scan 6 and 3 on the Programming Chart (inside back cover). ...

  • Hand Held Products 5700 - page 31

    2–7 SCANTEAM 5700 User’s Guide Hex V alue Symbology Chart Symbology 61 62 63 64 65 66 67 Codabar Code 39 UPC EAN Interleaved 2 of 5 Code 2 of 5 MSI Symbology 68 69 6A 6D 6E 99 Code 1 1 Code 93 Code 128 Matrix 2 of 5 Plessey All Symbologies (Prefix/Suffix Programming only .) Hex V alue Code ID [ a b c d e f g Code ID [ h i j m n Hex to ASCII Con ...

  • Hand Held Products 5700 - page 32

    2–8 SCANTEAM 5700 User’s Guide Interfunction Delay (x5mS) ] Intermessage Delay (x5mS) ] Output Delays Selection ] A two-digit number is required after scanning this programming bar code. Please scan your selection on the Programming Chart (inside back cover). Intercharacter Delay (x5mS) ] Medium ✱ High Beeper V olume Selection Off Low ✱ Def ...

  • Hand Held Products 5700 - page 33

    2–9 SCANTEAM 5700 User’s Guide ✱ None Low (500 milliseconds) Good Read Delay Selection Medium (1.0 second) High (1.5 second) High (1.0 second) Extra High (2.0 seconds) Reread Delay Selection ✱ Low (175 milliseconds) Medium (450 milliseconds) Enable ✱ Disable Laser V oting Selection This selection allows you to set a time period that must ...

  • Hand Held Products 5700 - page 34

    2–10 SCANTEAM 5700 User’s Guide Enable ✱ Disable Code I.D. T ransmit Selection Enable ✱ Disable AIM I.D. T ransmit Selection ✱ Enable Disable Function Code T ransmit Selection ✱ Enable Disable Buffered Scans Selection This allows you to enable or disable transmission of a Code I.D. before the decoded bar code symbology . (See the Symbol ...

  • Hand Held Products 5700 - page 35

    2–1 1 SCANTEAM 5700 User’s Guide ✱ Default All Serial Communication Settings ✱ Enable ✱ Disable CTS Check Selection 300 600 Baud Rate Selection 1200 2400 4800 ✱ 9600 19200 38400 This selection allows you to select the software programming feature that checks for a CTS signal, if your application does not have a CTS I/O line. Default = D ...

  • Hand Held Products 5700 - page 36

    2–12 SCANTEAM 5700 User’s Guide RS-232 W ord Length Selection 7 Data, 2 Stop 8 Data, 1 Stop ✱ 7 Data, 1 Stop Parity Selection Mark Space None Odd ✱ Even This selection allows you to set the RS-232 word length at seven or eight bits of data per character . The number of start and stop bits is fixed at one each. If an application requires onl ...

  • Hand Held Products 5700 - page 37

    2–13 SCANTEAM 5700 User’s Guide ✱ Record Protocol Selection Xon / Xoff Ack / Nak To P 2 T o P1 and P2 Serial W edge Output Selection ✱ To P 1 This selection allows you to program the scanner for the protocol required by your application. The protocol is a set of rules concerning the exchange of data between serially communicating devices. T ...

  • Hand Held Products 5700 - page 38

    2–14 SCANTEAM 5700 User’s Guide Data Format Editor This selection provides editing of all input (scanned) data. All Industrial and Retail symbologies can be formatted. Y ou may scan the Clear Data Format bar code if you are certain you want to delete or clear all formats. Use the Data Format Editor by following the steps below: ➊ Scan the Ent ...

  • Hand Held Products 5700 - page 39

    2–15 SCANTEAM 5700 User’s Guide Enable ✱ Disable Require Data For mat Enter Data Format Clear All Data Formats Data For mat Editor Status Check Show Formats Scan the Show Formats bar code to transmit the existing Data Format Editor formats. One format per line will be printed out. When disabled, the bar code data will be output to the host as ...

  • Hand Held Products 5700 - page 40

    2–16 SCANTEAM 5700 User’s Guide Format Editor Commands Chart F1 Send all characters followed by “XX” key or function code, starting from current cursor position. Syntax = F1XX (XX = HEX ASCII character or function code 00–FE HEX). Send Commands F2 Send “NN” characters followed by “XX” key or function code, starting from current cu ...

  • Hand Held Products 5700 - page 41

    2–17 SCANTEAM 5700 User’s Guide Y ou are using an IBM PC A T and are scanning a UPC A bar code with a five digit addenda (shown below). The bar code has a total of 18 characters, including the number system, the check digits, and a space between the main bar code data and the addenda bar code data. Data Formatter Example H Scan the Enter Data F ...

  • Hand Held Products 5700 - page 42

    2–18 SCANTEAM 5700 User’s Guide ...

  • Hand Held Products 5700 - page 43

    3–1 SCANTEAM 5700 User ’s Guide Introduction Use this chapter to program the Hand-Held Laser Scanner for General Operating features. This programming section contains the following menuing selections: • Laser Options • W and Emulation • Country Code • Keyboard ...

  • Hand Held Products 5700 - page 44

    3–2 SCANTEAM 5700 User’s Guide On ✱ Off Marker Beam Selection ✱ Enable Disable AutoT rigger Selection [ [ This programming feature is available only if you have purchased scanner models 5700/A–1X (refer to Sales Configuration Worksheet). When enabled, the scanner shows a marker or locator beam before the red scan line opens across a bar c ...

  • Hand Held Products 5700 - page 45

    3–3 SCANTEAM 5700 User’s Guide W ake Up Pulse Selection 10 ✱ 25 T ransmission Rate Selection 40 80 120 150 200 300 Enable ✱ Disable White High ✱ Black High Output Polarity Selection [ [ In Laser Emulation mode, the default polarity is White High. In W and Emulation mode, the default polarity is Black High. This programming selection sets ...

  • Hand Held Products 5700 - page 46

    3–4 SCANTEAM 5700 User’s Guide This programming selection allows you to re-map the keyboard layout for the selected country . As a general rule, the following characters are not supported by the scanner for countries other than the United States: @ | $ # { } [ ] = / ‘ < > ~ ✱ United States Belgium Foreign Keyboard Selection Denmark, ...

  • Hand Held Products 5700 - page 47

    3–5 SCANTEAM 5700 User’s Guide Note: The following Enable and Disable programming bar codes apply to SCANTEAM 5700 software prior to software revision level 2.0. NCR 7052 Keypad Selection [ Layout 2 (Calculator) Layout 3 (PC A T) ✱ Layout 1 (T elephone) A T Direct Connect Selection [ NCR 7052 applies to –X1 units only . This selection allow ...

  • Hand Held Products 5700 - page 48

    3–6 SCANTEAM 5700 User’s Guide Keyboard Style This programming selection allows you to program the scanner to support special keyboard features, such as CAPS LOCK, SHIFT LOCK, Data Entry , and CTRL+ codes. These special keyboard features are shown in the chart below . Default = Style A. Style A [ ASCII function codes (00–1F) are sent to the t ...

  • Hand Held Products 5700 - page 49

    3–7 SCANTEAM 5700 User’s Guide Keyboard Style Selections This programming selection allows you to program special keyboard features, such as Caps Lock and Shift Lock. Regular is used when you normally have the Caps Lock key off. Caps Lock is used when you normally have the Caps Lock key on. Shift Lock is used when you normally have the Shift Lo ...

  • Hand Held Products 5700 - page 50

    3–8 SCANTEAM 5700 User’s Guide Keyboard Style Modifiers This programming selection allows you to program special keyboard features, such as CTRL+ codes and T urbo Mode. Control + ASCII Mode On – If you scan this selection, the scanner sends key combinations for ASCII control characters for values 00–1F . Refer to page 6–1 for CTRL+ V alue ...

  • Hand Held Products 5700 - page 51

    4–1 SCANTEAM 5700 User’s Guide Introduction Use this chapter to program the Hand-Held Laser Scanner for Industrial and Retail Symbology selections. This programming section contains the following menuing selections: • Codabar Selections. • Code 39 Selections. • Code 93 Selections. • Interleaved 2 of 5 Selections. • Code 2 of 5 Selecti ...

  • Hand Held Products 5700 - page 52

    4–2 SCANTEAM 5700 User ’s Guide ✱ Default All Codabar Settings ✱ Codabar ✱ On Off Start / Stop Characters T ransmit ✱ Don’t Transmit Message Length Maximum ] Minimum ] ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back cover). Codabar Selection Decoding ...

  • Hand Held Products 5700 - page 53

    4–3 SCANTEAM 5700 User’s Guide Concatenation Don’t Allow (Concatenation Off) ✱ Allow Require V alidate, But Don’t Transmit ✱ No Check Character V alidate, And Transmit Check Character Codabar Selection, continued Concatenation Codabar supports symbol concatenation. When you Allow concatenation, the reader will look for a Codabar symbol ...

  • Hand Held Products 5700 - page 54

    4–4 SCANTEAM 5700 User’s Guide ✱ Default All Code 39 Settings ✱ Code 39 ✱ On Off T ransmit ✱ Don’t Transmit Start / Stop Characters Full ASCII ✱ Enable Disable Append Enable ✱ Disable ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back cover). Code 39 ...

  • Hand Held Products 5700 - page 55

    4–5 SCANTEAM 5700 User’s Guide V alidate, But Don’t T ransmit ✱ No Check Character V alidate, And Transmit Check Character Code 39 Selection, continued Message Length Maximum ] Minimum ] Decoding ✱ Adaptive T raditional Programming Tip: If a symbology will not be used, we recommend turning it off to minimize the chance of a misread. ...

  • Hand Held Products 5700 - page 56

    4–6 SCANTEAM 5700 User’s Guide Code 93 ✱ On Off Code 93 Selection ✱ Default All Code 93 Settings ✱ FULL ASCII CHART [ NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI %U $A $B $C $D $E $F $G $H $I $J $K $L $M $N $O DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US $P $Q $R $S $T $U $V $W $X $Y $Z %A %B %C %D %E SP ! ” # ...

  • Hand Held Products 5700 - page 57

    4–7 SCANTEAM 5700 User’s Guide Interleaved 2 of 5 ✱ On Off Message Length Maximum ] Minimum ] V alidate, But Don’t Transmit ✱ No Check Digit V alidate, And Transmit Check Digit Interleaved 2 of 5 Selection ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back c ...

  • Hand Held Products 5700 - page 58

    4–8 SCANTEAM 5700 User’s Guide Code 2 of 5 ✱ On Off Message Length Maximum ] Minimum ] Matrix 2 of 5 ✱ On Off Message Length Maximum ] Minimum ] Matrix 2 of 5 Selection Code 2 of 5 Selection ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back cover). ✱ Defaul ...

  • Hand Held Products 5700 - page 59

    4–9 SCANTEAM 5700 User’s Guide Code 128 ✱ On Off Message Length Maximum ] Minimum ] Code 128 Selection ✱ Default All Code 11 / Code 128 Settings ✱ ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back cover). Code 11 ✱ On Off ✱ 2 Check Digits 1 Check Digit ...

  • Hand Held Products 5700 - page 60

    4–10 SCANTEAM 5700 User’s Guide On ✱ Off Code 128 Function Character Selection When Code 128 Function Character is enabled, the scanner can substitute a <GS> for function character 1. T o enable the <GS> substitution, you must scan the Code 128 Function Character On bar code, and the <GS> Substitution On bar code. Note: For ...

  • Hand Held Products 5700 - page 61

    4–1 1 SCANTEAM 5700 User’s Guide Message Length Maximum ] Minimum ] Message Length Maximum ] Minimum ] Code 49 Selection [ Code 16K Selection [ ] A two-digit number is required after scanning this programming bar code. (16K may accept a 3–digit number .) Scan your selection on the Programming Chart (inside back cover). ✱ Default All Code 16 ...

  • Hand Held Products 5700 - page 62

    4–12 SCANTEAM 5700 User’s Guide EAN / JAN 13 ✱ On Off EAN / JAN 8 ✱ On Of f Check Digit ✱ T ransmit Don’t Transmit ✱ Default All EAN / UPC Settings ✱ EAN Selection ISBN Enable ✱ Disable Programming Tip: If a symbology will not be used, we recommend turning it off to minimize the chance of a misread. ...

  • Hand Held Products 5700 - page 63

    4–13 SCANTEAM 5700 User’s Guide UPC A ✱ On Off UPC E0 ✱ On Off UPC E1 On ✱ Off Check Digit ✱ T ransmit Don’t Transmit Number System ✱ T ransmit Don’t Transmit V ersion E Expand Expand ✱ Don’t Expand ✱ Default All UPC / EAN Settings ✱ UPC Selection Programming Tip: If a symbology will not be used, we recommend turning it of ...

  • Hand Held Products 5700 - page 64

    4–14 SCANTEAM 5700 User’s Guide Two Digit Addenda Enable ✱ Disable Five Digit Addenda Enable ✱ Disable EAN / UPC Addenda Require ✱ Don’t Require UPC Addenda Selection EAN Addenda Selection Two Digit Addenda Enable ✱ Disable Five Digit Addenda Enable ✱ Disable EAN / UPC Addenda For mat No Space ✱ Space Note: The EAN/UPC Addenda For ...

  • Hand Held Products 5700 - page 65

    4–15 SCANTEAM 5700 User’s Guide ✱ Default All MSI & Plessey Settings ✱ Plessey On ✱ Off Plessey Selection Message Length Maximum ] Minimum ] ] A two-digit number is required after scanning this programming bar code. Scan your selection on the Programming Chart (inside back cover). MSI On ✱ Off Message Length Maximum ] Minimum ] MSI ...

  • Hand Held Products 5700 - page 66

    4–16 SCANTEAM 5700 User’s Guide ...

  • Hand Held Products 5700 - page 67

    5–1 SCANTEAM 5700 User ’s Guide The scanner ’s internal operational firmware is contained in a “Flash EEPROM” (a programmable / erasable ROM – Read Only Memory). This enables you to download new firmware upgrades, without opening the scanner or changing a chip (IC). A download kit that includes the software (in DOS or Windows versions) ...

  • Hand Held Products 5700 - page 68

    5–2 SCANTEAM 5700 User’s Guide Scanning the Download New Firmware bar code prepares the scanner to be downloaded with new firmware. New firmware is downloaded by using the Quick*Load application software (in the download kit). Quick*Load can perform firmware uploads (reading the device’s memory) and downloads (writing to the device’s memory ...

  • Hand Held Products 5700 - page 69

    5–3 SCANTEAM 5700 User’s Guide For quick download communication configuration, scan the W + A bar code to temporarily configure the scanner for 9600 baud rate, no parity , 8 data bits, and 1 stop bit. Standard receive (RX) and transmit (TX) voltages are also selected. RTS / CTS handshaking is disabled. This change is temporary . The next time t ...

  • Hand Held Products 5700 - page 70

    5–4 SCANTEAM 5700 User’s Guide ...

  • Hand Held Products 5700 - page 71

    6–1 SCANTEAM 5700 User ’s Guide NUL 00 2 SOH 01 A STX 02 B ETX 03 C EOT 04 D ENQ 05 E ACK 06 F BEL 07 G BS 08 H HT 09 I LF 0A J VT 0B K FF 0C L CR 0D M SO 0E N SI 0F O DLE 10 P DC1 1 1 Q DC2 12 R DC3 13 S DC4 14 T NAK 15 U SYN 16 V ETB 17 W CAN 18 X EM 19 Y SUB 1A Z ESC 1B [ FS 1C GS 1D ] RS 1E 6 US 1F - Keyboard Function Relationships The fo ...

  • Hand Held Products 5700 - page 72

    6–2 SCANTEAM 5700 User’s Guide Supported Inter face Keys Supported Interface Keys NUL 00 SOH 01 STX 02 ETX 03 EOT 04 ENQ 05 ACK 06 BEL 07 BS 08 HT 09 LF 0A VT 0B FF 0C CR 0D SO 0E SI 0F DLE 10 DC1 1 1 DC2 12 DC3 13 DC4 14 NAK 15 SYN 16 ETB 17 CAN 18 EM 19 SUB 1A ESC 1B FS 1C GS 1D RS 1E US 1F Reserved Enter (KP) Cap Lock AL T make AL T break CT ...

  • Hand Held Products 5700 - page 73

    6–3 SCANTEAM 5700 User’s Guide Reserved Enter PF1 PF2 PF3 PF1 1 PF12 New Line PF4 TA B F13 F14 Remove New Line Insert Here Cursor Up Cursor Left Cursor Down Cursor Right Delete Print F15 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Reserved Enter PF10 PF1 1 PF12 Reserved Reserved New Line Field Forward Field Forward Reserved Field Forward Delete New Line Ins ...

  • Hand Held Products 5700 - page 74

    6–4 SCANTEAM 5700 User’s Guide Reserved New Line N/A N/A N/A N/A N/A New Line N/A Ta b N/A Ta b N/A New Line N/A Escape F1 1 Insert F13 Back Space Back T ab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Supported Inter face Keys Supported Interface Keys NUL 00 SOH 01 STX 02 ETX 03 EOT 04 ENQ 05 ACK 06 BEL 07 BS 08 HT 09 LF 0A VT 0B FF 0C CR 0D SO 0E SI 0F ...

  • Hand Held Products 5700 - page 75

    6–5 SCANTEAM 5700 User’s Guide Reserved Enter Caps Reserved Reserved Reserved Reserved Reserved Back Space Ta b Reserved Reserved Reserved Return Reserved Reserved Home Reserved Reserved Reserved Reserved Clear Screen F1 F2 F3 F4 F5 Escape F6 F7 F8 Reserved Reserved T ransmit Reserved Reserved Reserved Backtab Reserved Carriage Return Back Spac ...

  • Hand Held Products 5700 - page 76

    6–6 SCANTEAM 5700 User’s Guide Reserved Enter Reserved Reserved Reserved Reserved Reserved Return Reserved Ta b Line Feed Reserved Reserved Return Reserved Cursor Up Cursor Left Cursor Down Cursor Right Back Space Reserved Reserved F1 F2 F3 F4 F5 (CTRL F1) F6 (CTRL F2) F7 (CTRL F3) F8 (CTRL F4) F9 (SHIFT F2) F10 (SHIFT F3) Supported Inter face ...

  • Hand Held Products 5700 - page 77

    7–1 SCANTEAM 5700 User’s Guide Sectio 7 Product Specifications 7 ounces (198 g) 5.8 inches (14.8 cm) 5.8 inches (14.8 cm) 3.0 inches (7.6 cm) 670 nm visible laser diode (VLD); 5700ALR = 650nm VLD 36 ± 3 scans per second Minimum Reflective Difference = 25% (5700/A); MRD = 40% (5700ALR, 5700/HD) ± 65 degrees (from perpendicular) – 5700/A ± 6 ...

  • Hand Held Products 5700 - page 78

    7–2 SCANTEAM 5700 User’s Guide Laser Output only 5700–X0 (Laser Compatible Bar Image) Conventional laser data format is provided at the modular connector in the scanner handle. Signal Function Interface cables normally supplied with scanner model 5700–X0 are terminated with an 10 pin modular plug (P1) and a 9 pin T ype D (Squeeze–to–rel ...

  • Hand Held Products 5700 - page 79

    7–3 SCANTEAM 5700 User’s Guide Laser Output only 5700–X4 (Laser Compatible Bar Image +12VDC Input*) Conventional laser data format is provided at the modular connector in the scanner handle. Signal Function Interface cables normally supplied with scanner model 5700–X0 are terminated with an 10 pin modular plug (P1) and a 9 pin T ype D (Sque ...

  • Hand Held Products 5700 - page 80

    7–4 SCANTEAM 5700 User’s Guide W and Emulation 5700–X1, 5700–X2 Conventional wand data format is provided at the modular connector in the scanner handle. Signal Function Interface cables normally supplied with scanner model 5700–X1 and 5700–X2 are terminated with an 10 pin modular plug (P1) and a 9 pin T ype D (Squeeze–to–release) c ...

  • Hand Held Products 5700 - page 81

    7–5 SCANTEAM 5700 User’s Guide RS–232 5700–X1, 5700–X2 (TTL) and 5700–X3 (T rue) Decoded output data format is provided at the modular connector in the scanner handle. Signal Function Interface cables normally supplied with scanner model 5700–X1, 5700–X2 (TTL), and 5700–X3 (T rue) are terminated with an 10 pin modular plug (P1) an ...

  • Hand Held Products 5700 - page 82

    7–6 SCANTEAM 5700 User’s Guide Laser Output 5700–X1, 5700–X2 (Laser Compatible Bar Image, Low Power/Dual Inter face) Conventional laser data format is provided at the modular connector in the scanner handle. Signal Function Interface cables normally supplied with scanner model 5700–X1 and 5700–X2 are terminated with an 10 pin modular pl ...

  • Hand Held Products 5700 - page 83

    8–1 SCANTEAM 5700 User’s Guide The Hand-Held Decoded Output Laser Scanner provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks insure dependable scanner operation: Maintenance Cleaning the Scan Window Scanning performance may degrade if the scan window is ...

  • Hand Held Products 5700 - page 84

    8–2 SCANTEAM 5700 User’s Guide Replacing the Inter face Cable The standard interface cable is attached to the scanner with an 8–pin modular connector . When properly seated, the connector is held in the scanner handle by a flexible retention tab. The cable’s designed to be field replaceable. Notes: • Order replacement cables from Welch Al ...

  • Hand Held Products 5700 - page 85

    8–3 SCANTEAM 5700 User’s Guide T roubleshooting The Hand-Held Decoded Output Laser scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly , review the following T roubleshooting Guide to try to isolate the problem. T roubleshooting Guide Is the power on? Is the red illuminated beam on? If ...

  • Hand Held Products 5700 - page 86

    8–4 SCANTEAM 5700 User’s Guide Does the scanner read your bar code incorrectly? If the scanner reads a bar code ( one beep for a good read ), but the bar code is not displayed correctly on the host screen: ➊ The scanner may not be programmed for the appropriate terminal interface. Example: Y ou scan “12345” and the host displays “@es%.? ...

  • Hand Held Products 5700 - page 87

    9–1 SCANTEAM 5700 User’s Guide European Office Welch Allyn, Ltd. Hondsruglaan 87 D 5628 DB Eindhoven The Netherlands T elephone: Int+ 31 40 242 4486 Fax: Int+ 31 40 2425672 United Kingdom Office Welch Allyn U.K., Ltd. Dallam Court Dallam Lane W arrington Cheshire W A2 7L T United Kingdom T elephone: Int+44–1925–240055 Fax: Int+44–1925–6 ...

  • Hand Held Products 5700 - page 88

    9–2 SCANTEAM 5700 User ’s Guide For service in Asia, please contact your Welch Allyn representative (at address below) or your local distributor . Asia / Pacific Office Welch Allyn 10/F T ung Sun Commercial Centre 194–200 Lockhart Road W anchai, Hong Kong T elephone: Int+852–251 1–3050 or 251 1–3132 Fax: Int+852–251–1355 For service ...

  • Hand Held Products 5700 - page 89

    9–3 SCANTEAM 5700 User’s Guide The warranty does not apply to product which have been damaged by improper handling, shipping, or misuse. The warranty does not apply , if, in the sole opinion of Welch Allyn, Inc., the unit has been damaged by accident, misuse, neglect, improper shipping and handling. Since the unit is sensitive to static, the re ...

  • Hand Held Products 5700 - page 90

    9–4 SCANTEAM 5700 User ’s Guide ...

  • Hand Held Products 5700 - page 91

    SCANTEAM 5700 User ’s Guide The following chart lists the factory default Serial Interface Menu settings (indicated by a “ ✱ ” on the programming menu pages). Parameter Name Page Reference Default Setting Prefix / Suf fix Selections Beeper V olume High Page 2–8 Output Selections Code I.D. T ransmit Disable Page 2–10 AIM I.D. T ransmit D ...

  • Hand Held Products 5700 - page 92

    SCANTEAM 5700 User’s Guide The following chart lists the factory default General Operating Menu settings (indicated by a “ ✱ ” on the programming menu pages). Parameter Name Page Reference Default Setting Laser Options W and Emulation Selections T ransmission Rate 25 ips Page 3–3 W ake Up Pulse Disable Page 3–3 Country Code Selections F ...

  • Hand Held Products 5700 - page 93

    SCANTEAM 5700 User’s Guide The following chart lists the factory default Industrial Symbology Menu settings (indicated by a “ ✱ ” on the programming menu pages). Parameter Name Page Reference Default Setting Code 39 Selections Symbology Menu Defaults – Industrial Codabar Selections Codabar On Page 4–2 Start / Stop Characters Don’t T r ...

  • Hand Held Products 5700 - page 94

    SCANTEAM 5700 User’s Guide The following chart lists the factory default Industrial Symbology Menu settings (indicated by a “ ✱ ” on the programming menu pages). Parameter Name Page Reference Default Setting Symbology Menu Defaults – Industrial Code 11 Selections Code 1 1 On Page 4–9 Check Digits Required 2 Check Digits Page 4–9 Messa ...

  • Hand Held Products 5700 - page 95

    SCANTEAM 5700 User’s Guide The following chart lists the factory default Retail Symbology Menu settings (indicated by a “ ✱ ” on the programming menu pages). Parameter Name Page Reference Default Setting Symbology Menu Defaults – Retail EAN Selections MSI Selections MSI Off Page 4–15 Page 4–15 Message Length Min = 4, Max = 48 Plessey ...

  • Hand Held Products 5700 - page 96

    SCANTEAM 5700 User’s Guide ...

  • Hand Held Products 5700 - page 97

    ...

  • Hand Held Products 5700 - page 98

    ...

  • Hand Held Products 5700 - page 99

    0 1 2 3 4 5 67 8 9 A B C D E F ...

  • Hand Held Products 5700 - page 100

    Code 128 CODE 128 Interleaved 2 of 5 1234567890 Code 39 TEST–SHEET Code 2 of 5 Matrix 2 of 5 123456 6543210 123456–9$ Code 93 UPC A with 5 digit addenda 56098 0 12345 67890 5 EAN 13 9 780330 290951 5700/DO/UG Rev K Skaneateles Falls, New Y ork 13153–0187 P .O. Box 187 4619 Jordan Road ...

Manufacturer Hand Held Products Category Scanner

Documents that we receive from a manufacturer of a Hand Held Products 5700 can be divided into several groups. They are, among others:
- Hand Held Products technical drawings
- 5700 manuals
- Hand Held Products product data sheets
- information booklets
- or energy labels Hand Held Products 5700
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hand Held Products 5700.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hand Held Products 5700, service manual, brief instructions and user manuals Hand Held Products 5700. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hand Held Products 5700.

Similar manuals

A complete manual for the device Hand Held Products 5700, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hand Held Products 5700 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hand Held Products 5700.

A complete Hand Held Products manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hand Held Products 5700 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hand Held Products 5700, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hand Held Products 5700, that we can find in the current document
3. Tips how to use the basic functions of the device Hand Held Products 5700 - which should help us in our first steps of using Hand Held Products 5700
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hand Held Products 5700
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hand Held Products 5700 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hand Held Products 5700?

Use the form below

If you did not solve your problem by using a manual Hand Held Products 5700, ask a question using the form below. If a user had a similar problem with Hand Held Products 5700 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)