English dropdown-ico

Manual Faber 36

14 pages 0.53 mb
Download

Go to site of 14

Summary
  • Faber 36 - page 1

    V ersion 04/08 - Page 1 PERLA W all Mount Canopy Rangehood READ AND SA VE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner . The homeowner must keep these instructions for future reference and for local electrical inspectors' use. • Installation Instructions • Use and Care Information READ THESE INSTRUCTION ...

  • Faber 36 - page 2

    V ersion 04/08 - Page 2 VENTING REQUIREMENTS Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof. The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient performance. The size of the ductwork should be uniform. Do not install two elbows to ...

  • Faber 36 - page 3

    V ersion 04/08 - Page 3 RÈGLEMENTS D'ÉV ACUA TION Conrmer la sortie d'évacuation - soit par le mur , soit par le toit. Uti lise z une longu eur de tuyau teri e mini male avec les mo indre s de coudes pour la plus grande efcacité. Le diamètre de tuyauterie doit être uniforme. N'installez jamais 2 coudes ensemble. Scellez b ...

  • Faber 36 - page 4

    V ersion 04/08 - Page 4 (B) 24" high, mounts to the wall beneath the rangehood for a coordinated look 24” High Backsplash/Dosseret 24 po 30 x 24 Stainless 30 x 24 White 30 x 24 Black 36 x 24 Stainless 36 x 24 White 36 x 24 Black 6098835 6098836 6098837 6098815 6098816 6098817 Ductless Conversion Kit/ Kit Pour Conversion Du Conduit 6097340 60 ...

  • Faber 36 - page 5

    V ersion 04/08 - Page 5 TOOLS NEEDED FOR INST ALLA TION • Saber Saw or Jig Saw • Drill • 1 1/4" Wood Drill Bit • Pliers • Phillips Screwdriver • Flat Blade Screwdriver • Wire Stripper or Utility Knife • Metal Snips • Measuring T ape or Ruler • Level • Pencil • Caulking Gun • Duct T ape P ARTS SUPPLIED FOR INST ALLA TI ...

  • Faber 36 - page 6

    V ersion 04/08 - Page 6 PREP ARE THE W ALL 1. Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt. 2. Determine and clearly mark with a pencil the center line on the wall where the ...

  • Faber 36 - page 7

    V ersion 04/08 - Page 7 FIGURE 9 6. Connect the Power Supply Cable to the rangehood. At - tach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connector . Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector . Connect the Green (Green and Y e ...

  • Faber 36 - page 8

    V ersion 04/08 - Page 8 Light On/Off Button ( L ) On/Off switch for the halogen lights. Move the switch to "1" to turn the light ON and to "0" to turn it OFF . Blower On/Off Button ( M ) On/Off switch for the blower . Move the switch to "1" to turn the blower ON and to "0" to turn it OFF . Blower Speed Button ...

  • Faber 36 - page 9

    V ersion 04/08 - Page 9 F ABER W ARRANTY & SER VICE (SA VE FOR YOUR RECORDS) All Faber products are warranteed against any defect in materials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replacement parts. To obtain warranty service, contact the dealer from ...

  • Faber 36 - page 10

    V ersion 04/08 - Page 10 ASSEMBLAGE DE LA HOTTE OUTILS NÉCESSAIRES À L’INST ALLA TION • Scie sauteuse ou à découper • Perceuse • Foret à bois 1 1/4 po • Pinces • T ournevis Phillips • T ournevis à lame plate • Dénude l ou couteau tout usage • Pince coupante à l métallique • Ruban à mesurer ou règle • Niveau ? ...

  • Faber 36 - page 11

    V ersion 04/08 - Page 1 1 4. La cheminée s’installe au mur par deux xations (2 de la FIGURE 5) . Noter la position des xations. La xation supérieure doit être installée à environ 1/8 po du plafond. La xation inférieure doit être installée au point inférieur du manchon de la cheminée supérieure. Déterminer l’emplacement a ...

  • Faber 36 - page 12

    V ersion 04/08 - Page 12 6. Brancher le câble d’alimentation sur la hotte. Attacher le l blanc du câble d’alimentation sur le l blanc de la hotte avec une cosse. Attacher le l noir du câble d’alimentation au l noir de la hotte avec une cosse. Brancher le l de mise à la terre vert (jaune et vert) sous la vis de mise à la te ...

  • Faber 36 - page 13

    V ersion 04/08 - Page 13 DIAGRAMME DE CÂBLAGE • Cette hotte utilise les ampoule halogènes de 20 W . UTILISA TION ET ENTRETIEN Ce tte hott e es t con çue pour enl eve r la fumé e, les vape urs de cuisson et les odeurs de la cuisine. Panneau de commandes Le panneau de commandes est situé sur le côté droit sous la hotte . La position et la fo ...

  • Faber 36 - page 14

    V ersion 04/08 - Page 14 F ABER GARANTIE ET SERVICE ( ÉCONOMISER POUR VOS ENREGISTREMENTS ) Faber garantit à l’utilisateur-acheteur d’origine que les produits Faber vendus neufs par nous sont sans vice de matériel et de main-d’oeuvre d’origine pour une période d’un an à partir de la date d’achat. La garantie couvre la main-d’oeuv ...

Manufacturer Faber Category Ventilation Hood

Documents that we receive from a manufacturer of a Faber 36 can be divided into several groups. They are, among others:
- Faber technical drawings
- 36 manuals
- Faber product data sheets
- information booklets
- or energy labels Faber 36
All of them are important, but the most important information from the point of view of use of the device are in the user manual Faber 36.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Faber 36, service manual, brief instructions and user manuals Faber 36. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Faber 36.

Similar manuals

A complete manual for the device Faber 36, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Faber 36 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Faber 36.

A complete Faber manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Faber 36 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Faber 36, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Faber 36, that we can find in the current document
3. Tips how to use the basic functions of the device Faber 36 - which should help us in our first steps of using Faber 36
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Faber 36
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Faber 36 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Faber 36?

Use the form below

If you did not solve your problem by using a manual Faber 36, ask a question using the form below. If a user had a similar problem with Faber 36 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)