-
QSC PL-1.0 - page 1
33 ▼ PL-1.0 ▼ PL-1.0 HV ▼ PL-1.4 ▼ PL-1.5 X ▼ PL-1.6 HVX ▼ PL-1.8 ▼ PL-2.0 HV ▼ PL-2.4 MB PowerLight ™ Series TD-000063-00 Rev. C User Manual Manuel de l’utilisateur Bedienhandbuch Manual del Usuario TD-000063-00 ...
-
QSC PL-1.0 - page 2
...
-
QSC PL-1.0 - page 3
1 T urn-on/turn-off m uting .................................... 24 Mise en sourdine lors de la mise sous/hors tension Stummschaltung bei An- und Ausschalten Enmudecimiento de encendido/apagado Short circuit protection .................................... 2 4 Protection contre les court-circuits Schutz bei Kurzschluß Protección contra corto-circu ...
-
QSC PL-1.0 - page 4
2 Erklärung der Bildsymbole Das Blitzzeichen innerhalb eines gleichseitigen Dreiecks warnt den Benutzer vor nicht-isolierter , gefährlicher Spannung im Inneren des Gerätes. Diese Spannung ist hoch genug, um Personen durch elektrischen Schlag zu gefährden. Das Ausrufungszeichen innerhalb eines gleichseitigen Dreiecks weist den Benutzer auf wicht ...
-
QSC PL-1.0 - page 5
3 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses, and can radiate radio frequency energy and, if not ins ...
-
QSC PL-1.0 - page 6
4 © Copyright 1998, 2000 QSC Audio Products, Inc. QSC® is a registered trademark, and PowerLight™ and MultiSignal Processor™ are trademarks, of QSC Audio Products, Inc. “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. "Combo" is a trademark of Neutrik AG. All other trademarks are the property of ...
-
QSC PL-1.0 - page 7
5 INTRODUCTION EINFÜHRUNG INTRODUCCIÓN A V ANT -PROPOS This manual covers these eight PowerLight models. All are 2RU high (3.5 inches, or 8.9 centimeters) and weigh approximately 18 pounds (8.2 kilograms). PowerLight 1.0 T wo-channel model; 500 watts/channel @ 2 ohms. PowerLight 1.0 HV "High-voltage" two-channel model; 500 watts/ channe ...
-
QSC PL-1.0 - page 8
6 Front panel 1. Power switch 2. Protect, Standby , and Power LEDs 3. Gain control (Channel 1) 4. Clip limiter switch (Channel 1) 5. Clip, -10 dB, -20 dB and Signal LEDs (Channel 1) 6. Clip, -10 dB, -20 dB and Signal LEDs (Channel 2) 7. Clip limiter switch (Channel 2) 8 . Gain control (Channel 2) 9. Mounting holes for handles Panel frontal 1. Inter ...
-
QSC PL-1.0 - page 9
7 Rear panel 1. Parallel/Stereo/Bridge switch 2. Data port 3. Input barrier strip 4. Input (Channel 1) 5. Input (Channel 2) 6. + Output (Channel 1) 7. + Output (Channel 2) 8. - Output (Channel 1) 9. - Output (Channel 2) 10. Cooling fan 11. Remote power supply control 12. AC mains cable 13. Rear chassis support tab Panneau arrière 1. Sélecteur de ...
-
QSC PL-1.0 - page 10
8 MONT AGE Avant Utiliser quatre vis de montage. BEFESTIGUNG V orn Benutzen Sie vier Befestigungsschrauben. MONT AJE Frente Utilice cuatro tornillos. MOUNTING Front Use four mounting screws. ...
-
QSC PL-1.0 - page 11
9 Rear Rear rack ears are optional but recommended. Kits are available from QSC’ s T echnical Services Department or from your local dealer/distributor . Arrière Bien que facultatif, l’installation d’un support à l’arrière de l’amplificateur est recommandé. Un jeu de plaquettes est disponible à cet effet au département des services ...
-
QSC PL-1.0 - page 12
10 Operating voltage (AC mains) The serial number label indicates the correct AC mains voltage. Connecting to the wrong voltage is dangerous and may damage the amplifier . T ension d’utilisation (alimentation CA) L ’étiquette sur laquelle est inscrit le numéro de série de l’appareil indique la tension CA appropriée. Raccorder à une sourc ...
-
QSC PL-1.0 - page 13
11 Outputs Strip back insulation not more than 13 mm (½ inch). Sorties Dénuder le fil sur un maximum de 13 mm (½ pouce). Ausgänge Das Kabelende nicht länger als max. 13 mm abisolieren. Salidas Remueva el aislamiento no más de 13 mm (½ pulgada). Non-European models only . Insérer le fil de façon à ce qu'aucune partie du conducteur ne ...
-
QSC PL-1.0 - page 14
12 Speaker cabling Câblage du haut- parleur Lautsprecherkabel Cableado de bocinas Shorter cable Câblage plus court Kürzeres Kabel Cable más corto Larger wire size Section du fil plus gros Stärkerer Draht Cable más espeso More power Plus de puissance Höhere Leistung Más de potencia Longer cable Câblage plus long Längeres Kabel Cable más l ...
-
QSC PL-1.0 - page 15
13 • One amplifier • Un amplificateur • Ein Verstärker • Un amplificador • Multiple amplifiers • Multiples amplificateurs • Mehrere Verstärker • Multi amplificadores Operate Marche Betrieb Marcha Standby En attente OPERA TION Gain controls Actual voltage gain of amplifier , in dB. FONCTIONNEMENT Commandes de gain Gain de tension v ...
-
QSC PL-1.0 - page 16
14 Clip limiter The clip limiter will prevent continuous clipping in either amplifier channel output. Below clipping, and during short clips on peaks, the clip limiter does not act on the audio signal. Limiteur d'écrêtement Le limiteur d'écrêtement prévient l'écrêtement continuel. Sous le niveau d'écrêtement, et pendant ...
-
QSC PL-1.0 - page 17
15 LED indicators Indicateurs DEL LED-Anzeigen Indicadores LED • This red LED lights when the channel clips. • Este indicador LED rojo se enciende cuando el canal está recortando. • Cette DEL rouge s’allume pour indiquer l’écrêtement du signal. • Diese rote LED leuchtet bei Übersteuerung. • Diese grüne LED leuchtet bei etwa 30 dB ...
-
QSC PL-1.0 - page 18
16 Parallel, stereo, and bridged mono Modes parallèle, stéreo, et mono ponté (bridgé) Eingangsparallelschaltung, Stereobetrieb, und Mono-Brückenbetrieb Estéreo, paralelo y mono puente Ch. 1 Ch. 1 Ch. 1 Ch. 1 Ch. 1 Ch. 1 Ch. 2 Ch. 2 Ch. 2 Ch. 2 Ch. 2 Ch. 2 Ch. 1 input Ch. 1 input Ch. 1 input Ch. 2 input Ch. 2 input Ch. 2 input P arallel Stereo ...
-
QSC PL-1.0 - page 19
17 2 Ω 2 Ω 2 Ω 2 Ω Connecting outputs Connexion des sorties Ausgangsanschluß Conexión de las salidas POWERLIGHT 1.0 HV & POWERLIGHT 2.0 HV : POWERLIGHT 1.0, POWERLIGHT 1.0 HV , POWERLIGHT 1.4, POWERLIGHT 1.8, & POWERLIGHT 2.0 HV P ARALLEL AND STEREO OPERA TION (continued) OPÉRA TION EN MODES P ARALLÈLE ET STÉRÉO (suite) EINGANGSP ...
-
QSC PL-1.0 - page 20
18 BRIDGED MONO OPERA TION MONO-BRÜCKENBETRIEB FUNCIONAMIENTO EN MONO PUENTE OPÉRA TION EN MODE MONO STEREO PARALLEL BRIDGE dB dB CLIP -10dB -20dB SIGNAL CHANNEL 1 CHANNEL 2 Channel 2's gain control has no effect in this mode. Le contrôle de gain du canal 2 est hors circuit dans ce mode. Utiliser le canal 1 pour ajuster le gain. Use Channel ...
-
QSC PL-1.0 - page 21
19 32 16 8 Ω Ω Ω 4 Ω 4 Ω Connecting outputs (See instructions on page 11) Connexion des sorties (Voir instructions en page 11) Ausgangsanschluß (Anleitungen auf Seite 11) Conexión de las salidas (Instrucciones en pagina 11) 16 8 4 Ω Ω Ω 2 Ω 2 Ω Connecting outputs (See instructions on page 11) Connexion des sorties (Voir instructions en ...
-
QSC PL-1.0 - page 22
20 Using the PowerLight 1.5 X and 1.6 HVX CONNECTING INPUTS These models are designed for use with an external active crossover for bi-amp applications, as shown here. Connect the crossover's low- frequency output to the input of Channel 1, which is the higher- powered channel of the amplifier . Connect the high-frequency output of the crossov ...
-
QSC PL-1.0 - page 23
21 Instead of the "combo" connectors, you can also use the screw terminals for connecting inputs. POWERLIGHT 1.5 X & POWERLIGHT 1.6 HVX Au lieu des connecteurs "Combo," vous pouvez utiliser les bornes pour le branchement des entrées. En lugar de conectores ‘combo’, también puede usar las terminales de rosca para conect ...
-
QSC PL-1.0 - page 24
22 SL V RING TIP P2 P1 P3 PARALLEL OUTPUT LINE LEVEL OUTPUT INPUT RING P2 P1 P3 D A T A P O R T OUTPUT SL V RING TIP 16 8 4 2* Ω Ω Ω Ω PARALLEL OUTPUT parallel load (optional) charge parallèle (optionnel) Parallel-Last (möglic h) carga paralela (opcional) LINE-LEVEL A UDIO IN ENTRÉE A UDIO NIVEAU LIGNE LINEPEGEL-A UDIO-EINGANG ENTRADA DE NIV ...
-
QSC PL-1.0 - page 25
23 Use the additional connections shown for connecting to other amplifiers as needed. If you decide to connect the amplifiers via XLR-to- XLR, you will need either an XLR male-to-XLR male cable, or a male- to-male "gender changer" with a standard shielded XLR cable. NOTE: If you make an unbalanced input connection with any of a group of a ...
-
QSC PL-1.0 - page 26
24 T urn-on/turn-off muting The amplifier outputs are muted for a couple of seconds after turn-on, and immediately at turn-off. PROTECTION Short circuit protection The Output Averaging™ circuit protects the output devices from short circuits and stressful loads. SCHUTZSCHAL TUNGEN PROTECCIÓN Mise en sourdine lors de la mise sous/hors tension Les ...
-
QSC PL-1.0 - page 27
25 Thermal protection A variable-speed fan provides adequate cooling air flow . However, if the heatsink temperature should climb above 90° C, the outputs will mute until the amplifier cools down. Protection thermique Un ventilateur à vitesse variable fournit le courant d’air nécessaire au refroidissement de l’amplificateur . Si la températ ...
-
QSC PL-1.0 - page 28
26 PowerLight 1.0 PowerLight 1.0 HV PowerLight 1.4 PowerLight 1.5 X OUTPUT POWER in watts FTC: 20 Hz–20 kHz @ 0.1% THD 16 Ω per channel — 16 5 — — 8 Ω per channel 20 0 30 0 30 0 450 (Ch. 1), 200 (Ch. 2) 4 Ω per channel 32 5 50 0 50 0 700 (Ch. 1), 325 (Ch. 2) EIA: 1 kHz @ 1% THD 8 Ω per channel 21 0 32 5 32 5 475 (Ch. 1), 210 (Ch. 2) 4 ? ...
-
QSC PL-1.0 - page 29
27 PowerLight 1.6 HVX PowerLight 1.8 PowerLight 2.0 HV PowerLight 2.4 MB OUTPUT POWER in watts FTC: 20 Hz–20 kHz @ 0.1% THD 16 Ω per channel 425 (Ch. 1), 155 (Ch. 2) — 4 0 0 — 8 Ω per channel 725 (Ch. 1), 275 (Ch. 2) 40 0 65 0 1000 4 Ω per channel 1100 (Ch. 1), 450 (Ch. 2) 65 0 N / A 1550 EIA: 1 kHz @ 1% THD 16 Ω per channel 450 (Ch. 1), ...
-
QSC PL-1.0 - page 30
28 TECHNISCHE DA TEN SPECIFICA TIONS SPÉCIFICA TIONS ESPECIFICACIONES PowerLight 1.0 PowerLight 1.0 HV PowerLight 1.4 PowerLight 1.5 X AMPLIFIER PROTECTION Full short circuit†, open circuit, thermal, ultrasonic, and RF protection Stable into reactive or mismatched loads LOAD PROTECTION Turn-on/turn-off muting, DC-fault power supply shutdown, cli ...
-
QSC PL-1.0 - page 31
29 TECHNISCHE DA TEN SPECIFICA TIONS SPÉCIFICA TIONS ESPECIFICACIONES PowerLight 1.6 HVX PowerLight 1.8 PowerLight 2.0 HV PowerLight 2.4 MB AMPLIFIER PROTECTION Full short circuit†, open circuit, thermal, ultrasonic, and RF protection Stable into reactive or mismatched loads LOAD PROTECTION Turn-on/turn-off muting, DC-fault power supply shutdown ...
-
QSC PL-1.0 - page 32
30 WARRANTY INFORMA TION INFORMA TIONS DE GARANTIE GARANTIE- BEDINGUNGEN INFORMACIÓN DE GARANTÍA Disclaimer QSC Audio Products, Inc. is not liable for any damage to speakers, amplifiers, or any other equipment that is caused by negligence or improper installation and/or use of the PowerLight amplifier . Product Warranty QSC guarantees the PowerLi ...
-
QSC PL-1.0 - page 33
31 ADDRESS & TELEPHONE INFORMA TION ADRESSE POST ALE ET NUMÉROS DIRECCIÓN Y TELÉFONO ANSCHRIFT UND TELEFON- NUMMERN Mailing address / Adresse postale / Postanschrift / Dirección postal: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elephone Numbers / Numéros de téléphone / T elefonnummern / Números de ...
-
QSC PL-1.0 - page 34
32 ...
-
QSC PL-1.0 - page 35
...
-
QSC PL-1.0 - page 36
34 QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. ©1998, 2000 QSC Audio Products, Inc. ...
Do you have a question concerning QSC PL-1.0?
Use the form below
If you did not solve your problem by using a manual QSC PL-1.0, ask a question using the form below. If a user had a similar problem with QSC PL-1.0 it is likely that he will want to share the way to solve it.