English dropdown-ico

Manual Paradise RCP2-1000

48 pages 3.69 mb
Download

Go to site of 48

Summary
  • Paradise RCP2-1000 - page 1

    203987 Rev A ECO 3171 11/28/2005 Operations Manual RCP2-1000 Remote Controller for Rack Mount SSP As Paradise Datacom L LC Phone: (814) 238-3450 328 Innovation Blvd. Fax: (814) 238-3829 State College, PA 16803 USA Web: www.paradisedata.com Email: sales@paradisedata.com RCP2-1000 SSPA REMOTE CONTROLLER PARADISE DATACOM ...

  • Paradise RCP2-1000 - page 2

    2 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual PROPRIETARY NOTICE Paradise Datacom has made every effort to ensure that the instru ctions contained in this document are adequate and free of errors and omissions. Paradise Datacom will, if necessary, explain issues, which may not be covered by this document. Paradise Datacom’s lia ...

  • Paradise RCP2-1000 - page 3

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 3 T able of Contents Table of C ontents ........................................................................................................ 3 Section 1: Genera l Information .................................................................................. 7 1.0 Introdu ction ..... ...

  • Paradise RCP2-1000 - page 4

    4 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 3.2.1.6 Sys In fo Page 6 .................................................................................... 22 3.2.1.7 Sys In fo Page 7 .................................................................................... 22 3.2.1.8 Sys In fo Page 8 .................................. ...

  • Paradise RCP2-1000 - page 5

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 5 Section 5: Seri al Prot ocol ......................................................................................... 33 5.0 Introdu ction ................................................................................................. 33 5.1 Remote Control - Serial Comm unicati on ...

  • Paradise RCP2-1000 - page 6

    6 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual Figures Figure 1-1: Outline Dra wing of RCP2 -1000 RM ................................................. 7 Figure 2-1: RCP2-1000 RM Rear Panel ........................................................... 12 Figure 2-2: Cable Connec tions for RCP2- 1000 RM ............................... ...

  • Paradise RCP2-1000 - page 7

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 7 1.0 Introduction This section provides the general information for the Paradise Datacom LLC Redundant Control Panel for Ra ck Mount SSPAs. This secti on describes the supplied equipment and safety precautions. 1.1 Description The RCP2-1000 RM controller provides control of Paradise Da ...

  • Paradise RCP2-1000 - page 8

    8 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 1.2 Equipment Supplied The following equipment is supplied with each unit: • RCP2-1000 RM Redundant System Controller (1 RU high) • (2) IEC Line Cord Sets • Operations Manual (203987) RCP2 -1000 RM System Controller Paradise Data can provide t he following optional equipment: ? ...

  • Paradise RCP2-1000 - page 9

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 9 1.3.2 Electrical Discharge Hazards A spark can not only create ESD reliability pr oblems, it can also cause serious safety hazards. The following precautions should be taken when there is a risk of electrical discharge: • Follow all ESD guidelines. • Remove all flammable material ...

  • Paradise RCP2-1000 - page 10

    10 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual THIS PAGE LEFT INTENTIONALLY BLANK ...

  • Paradise RCP2-1000 - page 11

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 11 2.0 Introduction This section provides information for the initial inspe cti on, installation and external connections for the RCP2-1000 RM redundant system controller. 2.1 Inspection When the unit is received, an initial inspecti on should be completed. First, ensure that the shippi ...

  • Paradise RCP2-1000 - page 12

    12 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 2.5 Cable Connectors The RCP2-1000 RM has several I/O interconnections av ailable on the rear panel. The controller rear panel is shown in Figure 2-1. The RCP2-1000 RM and a Rack Mount SSPA are linked to gether through 2-wire twisted pair shielded cable (such as 24 AW G twisted pair ...

  • Paradise RCP2-1000 - page 13

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 13 Figure 2-3: Top Level Wiring Diagram ...

  • Paradise RCP2-1000 - page 14

    14 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual In order to achieve successful operati on of the RCP2-1000 RM , the SSPA must be configured with the following par ameters: Baud Rate - 9600; Serial Interface - RS485; Network Address - any. See your SSPA manual for details. Maximum cable length is 4000 feet (1.3 km). 2.5.1 Serial Po ...

  • Paradise RCP2-1000 - page 15

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 15 2.5.2 Serial Port, Local (J5) A DB9 male connector serves as a serial in terface with a remote SSPA. Interface parameters are set by internal RCP hardwar e and can't be reconfigured by user. The remote SSPA serial interface must be proper ly set to provide connection with the RC ...

  • Paradise RCP2-1000 - page 16

    16 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual Pin # Function Description 1 Closed on Power Supply Fault Form C relay NC 2 Opened on Power Supply Fault Form C relay NO 20 Power Supply Fault Common 3 1. Standalone mode. Closed on Auxiliary Fault 2. 1:1 Redundancy Mode. Closed on Auto matic switchover mode. Form C relay NC 21 1. St ...

  • Paradise RCP2-1000 - page 17

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 17 Section 3: RCP2-1000 RM Front Panel Operation 3.0 Introduction Control of the RCP2-1000 RM can be handled th rough Front Panel operation, or remotely through Parallel or Seri al communication to a computer. For Local (front panel) operati on of the controller, simply toggle the Local ...

  • Paradise RCP2-1000 - page 18

    18 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 3.1.4 Liquid Crystal Display The 40 character by 2 line fr ont panel liquid crystal displa y (LCD) provides a conven- ient method of selecting various operating par ameters of the controller. All internal set - tings can be achieved via the LCD and menu st ructure. There is no need t ...

  • Paradise RCP2-1000 - page 19

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 19 3.2 Main Menu The Main Menu organized in several functi onal subgroups, diagramed in Figure 3-2. 1. Sys.Info - System Information menu sublevel 2. PanelCom - Serial Communication-related settings 3. SSPA Setup - System operation-related settings 4. Panel Setup - Fault handling settin ...

  • Paradise RCP2-1000 - page 20

    20 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 3.2.1 Sys Info The informative sublevel of the menu structur e contains 8 pages, shown in Figure 3-3. The "Up" and "Down" keys allow the user to navigate through the pages. Pressing the "Left" and "Right" buttons will display the at tenuation a ...

  • Paradise RCP2-1000 - page 21

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 21 3.2.1.2 Sys Info Page 2 This page shows a variety of alarm states wh ich may be present within the HPA. Fault values could be "Fault", "Normal" and "N/A" • PS - power supply alarm, displays "Norma l" if HPA power supplies are normally op- era ...

  • Paradise RCP2-1000 - page 22

    22 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 3.2.1.5 Sys Info Page 5 Page 5 shows settings related to the HPA 1:1 Redundant System operation. • Mode - indicates HPA operational mode. Value can be set to "1:1" for 1:1 redun- dancy mode and "Stdaln" for stand alone mode; • Stby. - shows HPA standby state s ...

  • Paradise RCP2-1000 - page 23

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 23 If the HPA controller card can not reliabl y communicate with an SSPA module, that module will be declared faulted. Th is type of fault will not affe ct the HPA overall summary fault state, because the controller card has the ability to track RF module faults independently. 3.2.2 Pan ...

  • Paradise RCP2-1000 - page 24

    24 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 3.2.3.3 Redundancy Under this menu, the user may select the following red undancy settings for units in a 1:1 redundant mode. • Switching - User may select between Au to and Manual switching. • Standby Select - Allows user to select between Standby and Online states. • Standby ...

  • Paradise RCP2-1000 - page 25

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 25 3.2.4.2 Fault Latch Determines the alarm reporting condition. A latched alarm will remain indicate d on the front panel until the operator clear s the alarm by pressing t he “Enter” button. Unlatched alarms will allow the summary alarm indicator to stop displaying the alarm condi ...

  • Paradise RCP2-1000 - page 26

    26 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual THIS PAGE LEFT INTENTIONALLY BLANK ...

  • Paradise RCP2-1000 - page 27

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 27 4.0 Introduction The RCP2-1000 RM was designed to provide easy Remote Monitor and Control for the Paradise Datacom Rack Mount Solid State Power Amplifier (SSPA). The unit is designed to fit a standard 1 rack unit high, 19'' wide EIA rack. The RCP2-1000 allows the user to re ...

  • Paradise RCP2-1000 - page 28

    28 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 4.1.3 Voltage Regulator Output Low Fault Fault effective when remote SSPA internal vo ltage regulators drop output voltage below 8 volts. Fault always retains its last state when SSPA is muted. Fault threshold value is factory fixed and can't be changed by the user. Fault state ...

  • Paradise RCP2-1000 - page 29

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 29 4.1.9 RF Switch Fault In Redundant mode, the SSPA alwa ys tracks position of RF s witch(es). The user is informed about the RF switch state through t he front panel LCD and se rial protocol. If the switch position for any reason can't reliably be determined, the SSPA declares a ...

  • Paradise RCP2-1000 - page 30

    30 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 4.2 Design Philosophy The RCP2-1000 RM remote controller was designed to achieve a new level in high reli- ability, maintenance free operation. A tightly integrated modular assembly approach has been used to realize a versatile controller while maintaining its user friendly opera- to ...

  • Paradise RCP2-1000 - page 31

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 31 The digital core board also contains the in terface circuitry that allows the RCP2-1000 RM to be firmware upgradeable in the field. A block diagram of the Digital Core Board is shown in Figure 4-1. 4.2.2 I/O Board Assembly The I/O Board Assembly contains the primary (hardware) interf ...

  • Paradise RCP2-1000 - page 32

    32 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 32 XXXXXX Rev - Xyxyxyxy THIS PAGE LEFT INTENTIONALLY BLANK ...

  • Paradise RCP2-1000 - page 33

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 33 5.0 Overview A system, which includes an RCP2-1000 a nd Rack Mount SSPA, can be managed from a remote computer over serial interf ace. To achieve this, the RCP2-1000 utilize s the same serial protocol as the Rack Mount SSPA with some minor exceptions. Requested parameter changes wil ...

  • Paradise RCP2-1000 - page 34

    34 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 5.1.1 Header Packet The Header packet is divided into 3 sub-packets which are the Frame Sync, Destina- tion Address and Source Address packets (See Figure 5-2). 5.1.1.1 Frame Sync Word The Frame Sync word is a two byte field that marks the beginning of a packet. This value is always ...

  • Paradise RCP2-1000 - page 35

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 35 5.1.2 Data Packet The data sub-packet is comprised of 6 to 32 bytes of information. It is further divided into seven (7) fields as shown in Figure 5-3. The first six (6) fiel ds comprise the com- mand preamble while the last field is the actual data. 5.1.2.1 Protocol ID This field pr ...

  • Paradise RCP2-1000 - page 36

    36 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 5.1.2.4 Data Tag The data tag specifies the ty pe of internal resource of information needed to be ac- cessed on the amplifier. The dat a associated with certain tags is read only. Therefore, only the “Get” command byte would be associ ated with these data tags. The data tag byte ...

  • Paradise RCP2-1000 - page 37

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 37 5.1.2.6 Data Length This byte contains different information for Request and Response frames. In a Re- quest frame, it specifies the number of data bytes that are to be accessed starting from the first byte of the value s pecified in the Data Address by te. That byte must not ex- cee ...

  • Paradise RCP2-1000 - page 38

    38 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual 5.1.3.1 Frame Check The Frame Check field provides a checksum during packet transmission. This value is computed as a function of t he content of the destination address, source address and all Command Data Substructure bytes. In general, the sender formats a message fram e, calculat ...

  • Paradise RCP2-1000 - page 39

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 39 The Paradise Datacom RCP2-1000 utilizes Te rminal Mode Serial Pr otocol (TMSP) as a secondary serial protocol for Management and Control through a Remote Serial In- terface. TMSP allows the user to access internal SSPA functions via a r emote ASCII Terminal or its equivalent (such as ...

  • Paradise RCP2-1000 - page 40

    40 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual The following procedure will guide the user through the remote terminal setup, using the Windows 95/98 HyperTerminal software. The RCP2 must be connected to a PC com port and configured to use TMSP with 9600 Baud rate pr ior to setting up the PC configurations. • Start the Windows ...

  • Paradise RCP2-1000 - page 41

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 41 • In the next window, select the following as shown in Figure 6-3: Bits per Second: 9600; Data bits: 8; Parity: None; Stop bits: 1; Flow control: none. Click “OK”. • Normally, the SSPA will not echo back charac ters typed by the user in Terminal window. For added security and ...

  • Paradise RCP2-1000 - page 42

    42 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual • Your PC is now configured to work with the RCP2 in Terminal mode. To es- tablish a session with the RCP2, type “UNIT#170” Note : When using a RS485 connection, avoid using the global address (170). Instead, use the uni que RCP2 address. An example of a terminal mode session s ...

  • Paradise RCP2-1000 - page 43

    RCP2-1000 RM Remote Controller Operations M anual 203987 Rev A 43 Appendix A: Specifications The following pages comprise the specific ation sheet (203211) for the RCP2-1000 Remote Controller for Rack Mo unt SSPAs. For the latest revi sion of this document, refer to the Paradise Datacom w eb site (http://www.paradisedata.com). ...

  • Paradise RCP2-1000 - page 44

    44 203987 Rev A RCP2-1000 RM Remote Controller Operations M anual THIS PAGE LEFT INTENTIONALLY BLANK ...

  • Paradise RCP2-1000 - page 45

    RCP2-1000 Remote Control Panel for Rack Mount SSP As 203211 Rev C ECO 3171 1 OF 4 DESCRIPTION The Paradise Datacom Remote Control Panel (RCP2-1000-RM) was designed to provide easy remote monitor and control of Paradise Datacom’s Rack Mount Solid State Power Amplifier. Control of the RCP2-1000-RM can be handled through Front P anel operation, or r ...

  • Paradise RCP2-1000 - page 46

    RCP2-1000 Remote Control Panel for Rack Mount SSP As 203211 Rev C ECO 3171 2 OF 4 RCP2-1000 SSPA REMOTE CONTROLLER PARADISE DATACOM System Identification Fault Indicators Signal Path mimic display LCD Display Main Menu Key Local / Remote Key Auto / Manual Mode Key Enter Key Display Navigation Keys RCP2-1000 FRONT P ANEL DESCRIPTION Characteristic S ...

  • Paradise RCP2-1000 - page 47

    RCP2-1000 Remote Control Panel for Rack Mount SSP As 203211 Rev C ECO 3171 3 OF 4 Rear Panel Connectors and Pin Identification Main Serial Port (J4) Pin Outs Pin Function 1 RS485 TX+ (HPA Transmit +) 2 RS485 TX- (HPA Transmit -)/RS23 2 TX 3 RS485 RX+ (HPA Receive -)/RS 232 RX 4 RS485 RX- (HPA Receive +) 5 GND 6 Service Req u est 1 Form C relay NC c ...

  • Paradise RCP2-1000 - page 48

    RCP2-1000 Remote Control Panel for Rack Mount SSP As 203211 Rev C ECO 3171 4 OF 4 J7, Parallel I/O Connector Pin-out Pin # Function / Description 1 Closed on Power Suppl y Fault Form C relay NC 2 Opened on Power Supply Fault F orm C relay NO 20 Po wer Supply Fault Common 21 1. Standalone mode. Closed on Auxiliary Fault 2. 1:1 Redundancy Mode. Cl os ...

Manufacturer Paradise Category Universal Remote

Documents that we receive from a manufacturer of a Paradise RCP2-1000 can be divided into several groups. They are, among others:
- Paradise technical drawings
- RCP2-1000 manuals
- Paradise product data sheets
- information booklets
- or energy labels Paradise RCP2-1000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Paradise RCP2-1000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Paradise RCP2-1000, service manual, brief instructions and user manuals Paradise RCP2-1000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Paradise RCP2-1000.

Similar manuals

A complete manual for the device Paradise RCP2-1000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Paradise RCP2-1000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Paradise RCP2-1000.

A complete Paradise manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Paradise RCP2-1000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Paradise RCP2-1000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Paradise RCP2-1000, that we can find in the current document
3. Tips how to use the basic functions of the device Paradise RCP2-1000 - which should help us in our first steps of using Paradise RCP2-1000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Paradise RCP2-1000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Paradise RCP2-1000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Paradise RCP2-1000?

Use the form below

If you did not solve your problem by using a manual Paradise RCP2-1000, ask a question using the form below. If a user had a similar problem with Paradise RCP2-1000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)