English dropdown-ico

Manual Honda Outboard Motor BF200A

112 pages 1.83 mb
Download

Go to site of 112

Summary
  • Honda Outboard Motor BF200A - page 1

    HONDA 02001 Honda Motor Co., Ltd. -All Rights Reserved 2002 ...

  • Honda Outboard Motor BF200A - page 2

    The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Keep this owner’s manual handy, so you can refer to it at any time. This owner’s manual is considered a permanent part of the outboard motor and should remain with the outboard motor if resold. The ...

  • Honda Outboard Motor BF200A - page 3

    INTRODUCTION Congratulations on your selection of a Honda outboard motor. We are certain you will be pleased with your purchase of one of the finest outboard motors on the market. We want to help you get the best results from your new outboard motor and to operate it safely. This manual contains the information on how to do that; please read it car ...

  • Honda Outboard Motor BF200A - page 4

    INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safety of others are very important. And using this outboard motor safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazar ...

  • Honda Outboard Motor BF200A - page 5

    CONTENTS OUTBOARD MOTOR SAFETY .................................... 7 IMPORTANT SAFETY INFORMATION ................. 7 SAFETY LABEL LOCATIONS ................................. 9 CONTROLS AND FEATURES ................................... 10 CONTROL AND FEATURE IDENTIFICATION CODES ................................................................... 10 ...

  • Honda Outboard Motor BF200A - page 6

    CONTENTS INDICATORS ............................................................ 28 Alternator (AGC) Indicator .................................... 28 Programmed Fuel Injection (PGM-FI) Indicator ... 28 Oil Pressure Indicator ............................................. 29 Overheating Indicator ............................................ 29 Cooli ...

  • Honda Outboard Motor BF200A - page 7

    CONTENTS SERVICING YOUR OUTBOARD MOTOR ............... 52 THE IMPORTANCE OF MAINTENANCE ............ 52 MAINTENANCE SAFETY ...................................... 53 MAINTENANCE SCHEDULE ................................ 55 TRIM TAB ADJUSTMENT ..................................... 57 MANUAL RELIEF VALVE ..................................... 58 ENGINE ...

  • Honda Outboard Motor BF200A - page 8

    CONTENTS TRANSPORTING ......................................................... 81 INSTALLED ON BOAT ....................................... 81 REMOVED FROM BOAT ................................... 81 TAKING CARE OF UNEXPECTED PROBLEMS ..... 82 WITH OUTBOARD MOTOR WITH OUTBOARD MOTOR BATTERY WILL NOT CHARGE AND ELECTRIC STARTER WILL NOT OPERATE ... ...

  • Honda Outboard Motor BF200A - page 9

    OUTBOARD MOTOR SAFETY IMPORTANT SAFETY INFORMATION Honda BF200NBF225A outboard motors are designed for use with boats that have a suitable manufacturer’s power recommendation. Other uses can result in injury to the operator or damage to the outboard motor and other property. Most accidents can be prevented if you follow all instructions in this m ...

  • Honda Outboard Motor BF200A - page 10

    OUTBOARD MOTOR SAFETY Refuel With Care Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well- ventilated area, with the engine stopped. Never smoke near gasoline, and keep other flames and sparks away. Refuel carefully to avoid spilling fuel. Avoid overfilling the fuel tank. After refueling, tighten the filler ...

  • Honda Outboard Motor BF200A - page 11

    OUTBOARD MOTOR SAFETY SAFETY LABEL LOCATIONS I A WARNING I IPLACE TRANSMISSION IN NEUTRAL BEFORE STARTING. ID0 NOT OPERATE WITH ENGINE COVER REMOVED. IBE SURE THE ANTIVENTILATION PLATE IS BELOW THE ID0 NOT SHIFT TO REVERSE SUDDENLY AT HIGH WATER LINE. SPEED. 1 I ICHECK OIL LEVEL BEFORE STARTING. IFLUSH THE SYSTEM THOROUGHLY WITH FRESH WATER AFTER E ...

  • Honda Outboard Motor BF200A - page 12

    CONTROLS AND FEATURES CONTROL AND FEATURE IDENTIFICATION CODES Model BF225A BFZOOA Type XXCA XXA XCA XA LA XXCA XXA XCA XA LA 20.0 in (508 mm) e Transom Height 25.0 in (635 mm) e e e e 30.0 in (762 nun) e e e e Standard Rotating Propeller Shaft e e e e e e Counterrotating Propeller Shaft e e e e e e e e e e Power TrimiTilt e e e e Refer to this cha ...

  • Honda Outboard Motor BF200A - page 13

    CONTROLS AND FEATURES COMPONENT AND CONTROL LOCATIONS OIL FILLER CAP (inside engine cover) J ENGINE COVER : OIL LEVEL DIPSTICK /ENGINE COVER LATCH L STERN BRACKET ANODE I SPARK PLUG (under coil) COOLING SYSTEM INDICATOR TILT LOCK ENGINE OIL DRAIN BOLT .. . . , (inside cover) '... ... FRAME SERIAL u I, FLUSH PLUG CONNECTOR GEAR OIL LEVEL PLUG ...

  • Honda Outboard Motor BF200A - page 14

    CONTROLS AND FEATURES Remote Controls (optional equipment) (SIDE-MOUNT REMOTE CONTROL) (PANEL-MOUNT REMOTE CONTROL) GEARSHIFTmHROTTLE GEARSHIFTiTHROTTLE CONTROL LEVER NEUTRAL CONTROL LEVER RELEASE NEUTRAL OIL PRESSURE DICATOR LIGHT SPARE SWITCH CLI CONTROL LEVER FRICTION ADJUSTER LANYARD EMERGENCY STOP SWITCH SWITCH CLIP 12 ...

  • Honda Outboard Motor BF200A - page 15

    CONTROLS AND FEATURES (SINGLE TOP-MOUNT REMOTE CONTROL) GEARSHIFTRHROTTLE CONTROL LEVER CONTROL PANEL (for PANELD'OP-MOUNT type) OIL PRESSURE INDICATOR LIGHT INDICATOR LIGl SWITCH CLIP EMERGENCY STOP SWITCH (DUAL TOP-MOUNT REMOTE CONTROL) GEARSHIFTRHROTTLE CONTROL LEVERS POWER TRIM/TILT SWITCH (RIGHT) POWER TRIM/TILT SWITCH (LEFT) FAST IDLE BU ...

  • Honda Outboard Motor BF200A - page 16

    CONTROLS AND FEATURES Trim Meter (optional equipment) 14 ...

  • Honda Outboard Motor BF200A - page 17

    CONTROLS AND FEATURES CONTROLS Side-Mount Type Ignition Switch The ignition switch controls the ignition system and starter motor. Turning the ignition switch key to the START position operates the starter motor. The key automatically returns to the ON position when released from the START position. The ignition switch can be used to operate the st ...

  • Honda Outboard Motor BF200A - page 18

    CONTROLS AND FEATURES Switch Clip and Emergency Stop Switch EMERGENCY STOP SWITCH I ” LANYARD SWITCH CLIP SWITCH CLIP The switch clip must be inserted in the emergency stop switch in order for the engine to start and run. The lanyard must be attached to the operator’s PFD (Personal Flotation Device) or worn around the wrist as shown. When use ...

  • Honda Outboard Motor BF200A - page 19

    CONTROLS AND FEATURES Moving the control lever 30" from N (neutral) selects the gear, and further movement increases engine speed. The control lever automatically locks itself in the N (neutral) position. To move the lever out of the N (neutral) position, you must squeeze the neutral release lever on the underside of the lever handle. A fricti ...

  • Honda Outboard Motor BF200A - page 20

    CONTROLS AND FEATURES Fast Idle Lever N (neutral) MAXIMUM FAST IDLE The fast idle lever is only needed for starting carbureted outboard models. The BF200A and BF225A models use programmed fuel injection so, this lever will not be needed for starting. After the engine starts and if the outside temperature is below 41 OF (5"C), the fast idle lev ...

  • Honda Outboard Motor BF200A - page 21

    CONTROLS AND FEATURES Turning the ignition switch key to the START position operates the starter motor. The key automatically returns to the ON position when released from the START position. The ignition switch can be used to operate the starter motor only when the control lever (p. 21 ) is in the N (neutral) position, and the switch clip is in th ...

  • Honda Outboard Motor BF200A - page 22

    CONTROLS AND FEATURES Fast Idle Button N (neutral) FAST IDLE BUTTON By moving the control lever forward or reverse when the fast idle button is pushed in, the throttle opening will be increased without engaging the gears. It is necessary to position the control lever in N (neutral) to push in the fast idle button. Gearshift/Throttle Control Lever C ...

  • Honda Outboard Motor BF200A - page 23

    CONTROLS AND FEATURES Moving the control lever 35" from N (neutral) selects the gear, and further movement increases engine speed. The control lever automatically locks itself in the N (neutral) position. To move, the lever out of the N (neutral) position, you must squeeze the neutral release lever on the underside of the lever handle. A frict ...

  • Honda Outboard Motor BF200A - page 24

    CONTROLS AND FEATURES Top-Mount Type Ignition Switch ON START I OFF IGNITION / SWITCH KEY The ignition switch controls the ignition system and starter motor. Turning the ignition switch key to the START position operates the starter motor. The key automatically returns to the ON position when released from the START position. The ignition switch c ...

  • Honda Outboard Motor BF200A - page 25

    CONTROLS AND FEATURES The switch clip must be inserted in the emergency stop switch in order for the engine to start and run. The lanyard must be attached to the operator’s PFD (Personal Flotation Device) or worn around the wrist as shown. When used as described, the emergency stop switch and lanyard system stops the engine if the operator falls ...

  • Honda Outboard Motor BF200A - page 26

    CONTROLS AND FEATURES Moving the control lever 35" from N (neutral) selects the gear, and further movement increases engine speed. A friction adjuster inside the control box adjusts the operating resistance of the control lever(s). Less friction allows easier control lever movement. More friction helps to hold a steady throttle setting while c ...

  • Honda Outboard Motor BF200A - page 27

    CONTROLS AND FEATURES Common Controls Power Trim/Tilt Switch (side-mount type) G R (top-mount type) SINGLE TYPE POWER TRIM/TILT SWITCH CONTROL POWER LEVER TRIM/TILT SWITCH CONTROL LEVER (panel-mount type) POWER TRIM/TILT SWITCH POWER TRIM/TILT SWITCH DUAL TYPE CONTROL LEVER The power tridtilt switch is located on the control lever. It is a rocker s ...

  • Honda Outboard Motor BF200A - page 28

    CONTROLS AND FEATURES Power Tilt Switch POWER TILT SWITCH The power tilt switch is located on the engine pan. It is a rocker switch with UP and DN (down) positions for changing the angle of the outboard motor. The power tilt switch will operate without turning the ignition switch ON. This switch is used with the engine stopped to raise the outboard ...

  • Honda Outboard Motor BF200A - page 29

    CONTROLS AND FEATURES Engine Cover Latch ENGINE COVER LATCH The engine cover latch fastens the engine cover to the outboard motor. Trim Tab TIGHTENING YLT TRIM * TAB The trim tab compensates for "torque steer," which is a reaction of the outboard motor to propeller rotation. If uncompensated, torque steer would make the outboard motor ten ...

  • Honda Outboard Motor BF200A - page 30

    CONTROLS AND FEATURES Tachometer (optional equipment) t TACHOMETER The tachometer shows engine speed in revolutions per minute. Refer to the tachometer when using the throttle and power tridtilt controls to achieve the best performance from the boat. 28 INDICATORS Alternator (ACG) Indicator ACG INDICATOR LIGHT The ACG indicator light turns on and t ...

  • Honda Outboard Motor BF200A - page 31

    CONTROLS AND FEATURES Oil Pressure Indicator (side-mount type) (panel-mounVtop-mount types) When the green light is lit, oil pressure is OK. If oil pressure becomes low, the green light will go off, and the engine protection system will limit engine speed. Remote controls are also equipped with a buzzer that sounds when the green light goes off. Lo ...

  • Honda Outboard Motor BF200A - page 32

    CONTROLS AND FEATURES If the engine overheats, the red light will come on, and the engine will stop in 20 seconds after the engine protection system will limit engine speed, Remote controls are also equipped with a buzzer that sounds when the red light comes on. Engine overheating may be the result of clogged water intakes. Cooling System Indicator ...

  • Honda Outboard Motor BF200A - page 33

    CONTROLS AND FEATURES Overrev Limiter The engine is equipped with an overrev limiter to prevent the possibility of mechanical damage from excessive engine speed. The overrev limiter may be activated during operation, limiting engine speed, if the outboard motor is tilted excessively, or when ventilation occurs during a sharp turn. If the overrev li ...

  • Honda Outboard Motor BF200A - page 34

    BEFORE OPERATION ARE YOU READY TO GET UNDER WAY ? Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the outboard motor and its operation before you get under way. ...

  • Honda Outboard Motor BF200A - page 35

    BEFORE OPERATION Safety Inspection Look around the outboard motor for signs of oil or gasoline leaks. Check that the fuel hose is undamaged and properly connected. Wipe up any spills before starting the engine. Check the stern bracket to be sure the outboard motor is securely installed. Check that all controls are operating properly. Replace any da ...

  • Honda Outboard Motor BF200A - page 36

    OPERATION SAFE OPERATING PRECAUTIONS To safely realize the full potential of this outboard motor, you need a complete understanding of its operation and a certain amount of practice with its controls. Before operating the outboard motor for the first time, please review the IMPORTANT SAFETY INFORMATION on page 7 and the chapter titled BEFORE OPERAT ...

  • Honda Outboard Motor BF200A - page 37

    OPERATION FUEL PRIMING OUTLET END (MOTOR) PRIMING BULB INLET END (TANK) Hold the priming bulb up in the direction of the arrow, then squeeze the priming bulb several times until it feels firm, indicating that fuel has reached the engine. Check to be sure there are no fuel leaks before starting the engine. Do not squeeze the priming bulb when the en ...

  • Honda Outboard Motor BF200A - page 38

    OPERATION STARTING THE ENGINE Side-Mount Type EMERGENCY STOP ?WITCH SWITCH CLIP LANYARD 1. Put the emergency stop switch clip in the emergency stop switch, and attach the lanyard to your PFD (Personal Flotation Device) or to your wrist, as shown. The engine will not start or run, unless the clip is in the switch. The emergency stop switch clip an ...

  • Honda Outboard Motor BF200A - page 39

    OPERATION FAST IDLE RANGE 3. Leave the fast idle lever in the OFF (fully lowered) position. Fast idle lever cannot be raised unless the control lever is in the N (neutral) position. The control lever cannot be moved away from the N (neutral) position unless the fast idle lever is lowered. ON IGNITION SWITCH KEY 4. Turn the ignition switch key to th ...

  • Honda Outboard Motor BF200A - page 40

    OPERATION MAXIMUM FAST IDLE --I @) 5. Before getting under way, allow the engine to warm up sufficiently to ensure good performance. Above 41°F (5"C), warm up the engine for 2 or 3 minutes. Below 41 OF (5OC), warm up the engine for at least 10 minutes at 2,000 rpm. Raise the fast idle lever to achieve approximately 2,000 rpm. During the warm- ...

  • Honda Outboard Motor BF200A - page 41

    OPERATION Panel-Mount Type EMERGENCY STOP SWITCH SWITCH CLIP LANYARD 1. Put the emergency stop switch clip in the emergency stop switch, and attach the lanyard to your PFD (Personal Flotation Device) or to your wrist, as shown. The engine will not start or run, unless the clip is in the switch. The emergency stop switch clip and lanyard system is ...

  • Honda Outboard Motor BF200A - page 42

    OPERATION START SWITCH KEY 3. Turn the ignition switch key to the START position and hold it there until the engine starts. When the engine starts, release the key, allowing it to return to the ON position. If the engine fails to start within 5 seconds, release the key and wait at least 10 seconds before operating the starter again. Using the ele ...

  • Honda Outboard Motor BF200A - page 43

    OPERATION ~~ During the warm-up period, check the oil pressure indicator (p. 29 ), overheating indicator (p. 29 ), and cooling system indicator (p. 30 ). If the indicators show any abnormal condition, immediately stop the engine and determine the cause of the problem. Refer to TAKING CARE OF UNEXPECTED PROBLEMS, p. 82. 5. If the fast idle control w ...

  • Honda Outboard Motor BF200A - page 44

    OPERATION N (neutral) , 2. Set the control lever in the N (neutral) position. The engine will not start if the F (forward) or R (reverse) gears are engaged. START IGNITION . SWITCH KEY 3. Turn the ignition switch key to the START position and hold it there until the engine starts. When the engine starts, release the key, allowing it to return to ...

  • Honda Outboard Motor BF200A - page 45

    OPERATION N (neutral) FAST IDLE BUTTON 4. Before getting under way, allow the engine to warm up sufficiently to ensure good performance. Above 41 "F (5"C), warm up the engine for 2 or 3 minutes. Below 41 "F (5"C), warm up the engine for at least 10 minutes at 2,000 rpm. Push the fast idle button then move the control lever forwa ...

  • Honda Outboard Motor BF200A - page 46

    OPERATION To stop the engine in an emergency, pull the clip out of the emergency stop switch by pulling the lanyard. We suggest that you stop the engine this way occasionally to verify that the engine and emergency stop switch is operating properly. 44 Normal Engine Stopping Side-Mount Type I N (neutral) Panel-Mount Type N (neutral) W Top-Mount Typ ...

  • Honda Outboard Motor BF200A - page 47

    OPERATION Side-Mount Type Panel-Mount/Top-Mount Types OFF IGNITION KEY 2. Turn the ignition switch key to the OFF position. 3. When the boat is not in use, remove and store the ignition key and the emergency stop switch clip and lanyard. GEARSHIFTING AND THROTTLE OPERATION Side-Mount Type CONTROL LEVER GUL RELEASE LEVER N (neutral) n F (forward) ...

  • Honda Outboard Motor BF200A - page 48

    OPERATION Panel-Mount Type N (neutral) To shift gears, move the control lever to select F (forward), N (neutral) and R (reverse) gears. The control lever cannot be moved from the N (neutral) position unless the neutral release lever is squeezed t$$& , ,/'. I (side-mountlpanel-mount types). LEVER Top-Mount Type N (neutral) F(forWqh R (reve ...

  • Honda Outboard Motor BF200A - page 49

    OPERATION Top-Mount Type 0 FRICTION I CONTROL LEVER FRICTION ADJUSTER Adjust the throttle friction adjuster so the control lever will hold a constant throttle setting while cruising. STEERING Steer the boat in the same manner as an automobile. 47 ...

  • Honda Outboard Motor BF200A - page 50

    OPERATION CRUISING Engine Speed For best fuel economy, limit the throttle opening to 80%. Use the throttle friction control (p. 46 ) to help you hold a steady speed. For rough water conditions or large waves, slow down to prevent the propeller from rising out of the water. The engine is equipped with an overrev limiter to prevent the possibility of ...

  • Honda Outboard Motor BF200A - page 51

    OPERATION Side-Mount Type Panel-Mount Type POWER TRIM/TILT SWITCH Top-Mount Type (single type) POWER TRIM/TILT SWITCH (dual type) POWER TRIM/TILT SWITCH (RIGHT) MOTOR MOTOR TRIMMED TOO TRIMMED TOO LOW HIGH MOTOR TRIMMED CORRECTLY BOW TOO LOW DUE TO 1. LOAD IN THE FRONT 2. MOTOR TRIMMED TOO LOW BOW TOO HIGH DUE TO 1. LOAD IN THE REAR 2. MOTOR TRIMME ...

  • Honda Outboard Motor BF200A - page 52

    OPERATION If steering effort is not equal in both directions, adjust the trim tab to compensate for “torque steer,” which is the reaction of the outboard motor to propeller rotation. TIGHTENING BOLT TRIM TAB Adjust the trim tab with the engine stopped. Loosen the bolt above the trim tab, turn the trim tab, then tighten the bolt securely. When t ...

  • Honda Outboard Motor BF200A - page 53

    OPERATION POWER TILT SWITCH TILT LOCK LEVER (Lock position) I pimi- Do not attempt to use the power tilt switch to tilt the outboard motor down while the tilt lock lever is in the lock position. Damage to the power tilt system may occur. MANUAL RELIEF VALVE (To fix) The outboard motor can also be tilted manually after opening the manual relief ...

  • Honda Outboard Motor BF200A - page 54

    SERVICING YOUR OUTBOARD MOTOR THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. Improperly maintaining this outboard motor, or failure to correct a problem before operation, can cause a malfunction in which you could be seriously hurt or killed. Alwa ...

  • Honda Outboard Motor BF200A - page 55

    SERVICING YOUR OUTBOARD MOTOR MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Failure to properly follow maintenance instructions and precautions can cause you ...

  • Honda Outboard Motor BF200A - page 56

    SERVICING YOUR OUTBOARD MOTOR TOOL KIT (optional equipment) The following tools are supplied by your dealer for simple maintenance procedures and emergency repairs. Keep these items on the boat, so they will always be available if you need them. r -l . - OIL CHECK OWNER'S MANUAL FUSE PULLER 16 X 17 mm BOX WRENCH L J SCREWDRIVER - - s==s - l ...

  • Honda Outboard Motor BF200A - page 57

    SERVICING YOUR OUTBOARD MOTOR MAINTENANCE SCHEDULE r REGULAR SERVICE PERIOD (3) I Perform at every indicated month or operating hour interval. whichever comes first. First month I Each use I After use I or 20 hrs. ITEM 0 1 Engine oil Check level 0 I I I ... . * 0 1 Engine oil Check level 0 Every 6 months 400 hrs. 200 hrs. 100 hrs. or or or Ev ...

  • Honda Outboard Motor BF200A - page 58

    SERVICING YOUR OUTBOARD MOTOR REGULAR SERVICE PERIOD (3) Perform at every indicated month or operating hour interval, whichever comes first. Each use ITEM @ I Fuel filter Check Replace Fuel filter Replace (High pressure type) Thermostat Check 0 Fuel line Check I After usc First month or 20 hrs. L Every 6 months Every year Every 2 years 100 hrs. I ...

  • Honda Outboard Motor BF200A - page 59

    SERVICING YOUR OUTBOARD MOTOR TRIM TAB ADJUSTMENT The trim tab compensates for “torque steer” which is a reaction of the outboard motor to propeller rotation. If uncompensated, torque steer would make the outboard motor tend to turn to one side. When the trim tab is correctly adjusted, steering effort is equal in either direction. If steering e ...

  • Honda Outboard Motor BF200A - page 60

    SERVICING YOUR OUTBOARD MOTOR MANUAL RELIEF VALVE MANUAL RELIEF VALVE NUAL release) The outboard motor can be tilted manually after opening the manual relief valve. This feature enables the outboard motor to be tilted or lowered when no battery is connected. For manual tilting, use a screwdriver to turn the valve counterclockwise 1 or 2 turns. Clos ...

  • Honda Outboard Motor BF200A - page 61

    SERVICING YOUR OUTBOARD MOTOR Latch Adjustment A loose engine cover may rattle or allow water to enter. Check whether the engine cover fits properly and adjust if necessary. Engine Cover Clearance Inspection FRONT INSPEC~ION POINT REAR I Q i (4.8 - 5.8'mm) in P INSPECTION POINT With the engine cover in place, measure the clearance between the ...

  • Honda Outboard Motor BF200A - page 62

    SERVICING YOUR OUTBOARD MOTOR Engine Oil Level Check Check the engine oil level with the engine stopped and the outboard motor in the vertical position. 1. Unlock and remove the engine cover (p. 58 ). 2. Remove the dipstick and wipe it clean. OIL LEVEL DIPSTICK 3. Insert the dipstick all the way in, then remove it and check the oil level shown on t ...

  • Honda Outboard Motor BF200A - page 63

    SERVICING YOUR OUTBOARD MOTOR DRAIN PLUG 3. Place a suitable container below the oil drain guide to catch the used oil, then remove the oil filler cap and the drain plug. 4. Allow the used oil to drain completely, then reinstall the engine oil drain plug, and tighten it securely. Improper disposal of engine oil can be harmful to the environment. If ...

  • Honda Outboard Motor BF200A - page 64

    SERVICING YOUR OUTBOARD MOTOR Engine Oil Recommendations Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. l-FR++l SAE Viscosity Grades -30 -20 -10 0 10 20 30 40°C AMBIENT TEMPERATURE SAE 1 OW-30 is recommended for general use. The SAE oil viscosity and service classification are in the API label ...

  • Honda Outboard Motor BF200A - page 65

    SERVICING YOUR OUTBOARD MOTOR Lubrication Points Wipe the outside of the engine with a cloth dipped in oil. 6 ENGINE COVER ARM SHAFT Apply marine anticorrosion grease to the following parts: Lubrication interval: After the first 20 hours or 1 month, then every 100 hours or 6 months. (Refer to the maintenance schedule page THROTTLE AMSHIFT 55 ). App ...

  • Honda Outboard Motor BF200A - page 66

    SERVICING YOUR OUTBOARD MOTOR Spark Plug Service RECOMMENDED SPARK PLUGS: IZFRGFll (NGK) VKJ20RZ-M11 (DENSO) pEl Incorrect spark plugs can cause engine damage. 1. Disconnect the battery negative (-) terminal. 2. Unlock and remove the engine cover (p. 58 ). SPECIAL SCREWS L.ENGINE UNDER COVER 3. Remove the twenty special bolts, and remove the R. and ...

  • Honda Outboard Motor BF200A - page 67

    SERVICING YOUR OUTBOARD MOTOR SPARK PLUG WRENCH 6. Remove the spark plugs with a spark plug wrench and 17 mm wrench. 7. Inspect the spark plugs. Replace them if the electrodes are worn, or if the insulators are cracked or chipped. 8. Measure the spark plug electrode gap with a suitable gauge. The gap should be 0.039 - 0.051 inches (1.00 - 1.30 mm). ...

  • Honda Outboard Motor BF200A - page 68

    SERVICING YOUR OUTBOARD MOTOR 11. Install the ignition coil. Reinstall the bolt. 12. Push the wire connector onto the ignition coil. Make sure it locks in place. 13. Repeat this procedure for the other five spark plugs. 14. Reinstall the covers. When reinstalling the covers, make sure not to jam the wire harnesses in between the covers and engine c ...

  • Honda Outboard Motor BF200A - page 69

    SERVICING YOUR OUTBOARD MOTOR REFUELING Check the fuel level and refill if neccessary. Do not fill the fuel tank above the UPPER LIMIT. Refer to Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immed ...

  • Honda Outboard Motor BF200A - page 70

    SERVICING YOUR OUTBOARD MOTOR FUEL RECOMMENDATIONS Use unleaded gasoline with a pump octane rating of 86 or higher. These outboard motors are certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasoline or an oil/gasoline mixture. ...

  • Honda Outboard Motor BF200A - page 71

    Fuel Pump Filter Inspection and Replacement The fuel pump filter (inside the strainer cup) is located below the engine oil filter. Water or sediment accumulated in the filter can cause loss of power or hard starting. To prevent engine malfunction, inspect the filter and replace when necessary. SERVICING YOUR OUTBOARD MOTOR Gasoline is highly flamma ...

  • Honda Outboard Motor BF200A - page 72

    SERVICING YOUR OUTBOARD MOTOR Id FUEL FILTER (inside strainer cup) 2. Looking through the translucent strainer cup, check the fuel filter for water accumulation or sediment. SCREW (3) FUEL HOSES SUSPENSION STRAP 3. Remove the suspension strap from the strainer bracket, then remove the strainer assembly from the strap. Before removing the fuel fil ...

  • Honda Outboard Motor BF200A - page 73

    SERVICING YOUR OUTBOARD MOTOR 8. Prime the engine using the priming bulb (refer to page 35). Check for fuel leaks. Repair any fuel leaks if necessary. If loss of power or hard starting are found to be caused by excessive water or sediment accumulation in the fuel filter, inspect the fuel tank. Clean the fuel tank and tank filter if necessary. It ma ...

  • Honda Outboard Motor BF200A - page 74

    SERVICING YOUR OUTBOARD MOTOR SUSPENSION STRAP I FUELTUBES SCREW (3) 1. Remove the engine cover (see page 58). 2. Disconnect the water level sensor connector. 3. Remove the suspension strap from the water separator bracket, then remove the separator assembly from the strap. 4. Pinch the fuel tubes with tube clips to prevent fuel leakage. 5. Remove ...

  • Honda Outboard Motor BF200A - page 75

    SERVICING YOUR OUTBOARD MOTOR Anode Replacement ANODE (stern bracket) ANODE (each side) The anodes are located on each side of the gearcase. They are made of a sacrificial material that helps to protect the outboard motor from corrosion. Replace the anodes when they have been reduced to about half their original size, or if they are crumbling. piq ...

  • Honda Outboard Motor BF200A - page 76

    SERVICING YOUR OUTBOARD MOTOR Propeller Replacement Before replacing the propeller, remove the clip from the engine stop switch to prevent any possibility of the engine being started while you are working with the propeller. The propeller blades may have sharp edges, so wear heavy gloves to protect your hands. Removal 1. Remove the cotter pin, unsc ...

  • Honda Outboard Motor BF200A - page 77

    STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your outboard motor troublefree and looking good. The following steps will help to keep rust and corrosion from impairing your outboard motor’s function and appearance, and will make the engine easier to start when you use the outboard motor again. Cleaning and Flushi ...

  • Honda Outboard Motor BF200A - page 78

    STORAGE FLUSH PLUG CONNECTOR WATER HOSE (Commercially available) 2. Screw the water hose into the flush plug connector. 3. Turn on the fresh water supply and flush the outboard motor for at least 10 minutes. 4. After flushing, remove the garden hose adapter, and install the flush plug cap. 76 ...

  • Honda Outboard Motor BF200A - page 79

    STORAGE Fuel Gasoline will oxidize and deteriorate in storage. Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system. If the gasoline in your fuel tank and vapor separetor deteriorates during storage, you may need to have the vapor separetor and other fuel system components serviced or replaced. The length of t ...

  • Honda Outboard Motor BF200A - page 80

    STORAGE 4. Tilt up the outboard motor. 5. Tilt down the outboard motor, and drain the vapor separator. 6. After draining thoroughly, tighten the drain bolt securely. 7. Clip the drain hose on the head cover. 8. Drain the fuel tank into an approved gasoline container, or if you need to store fuel in the fuel tank, you can extend fuel storage life by ...

  • Honda Outboard Motor BF200A - page 81

    STORAGE S 2. Attach the hoist hooks to the lifting eyes. 3. Disconnect the outboard motor from the boat, hoist the outboard motor, and move it to the storage area. 4. After the outboard motor is placed in storage and disconnected from the hoist, install the engine cover. STORAGE PRECAUTIONS Select a well-ventilated storage area. If possible, avoid ...

  • Honda Outboard Motor BF200A - page 82

    STORAGE PROTECTOR If it is necessary to store the outboard motor horizontally, drain the vapor separator (p. 77 ), and drain the engine oil (p. 60 ), before removing the outboard motor from the boat. Rest the motor on and cushion of protective packing material. Cover the outboard motor to keep out dust. Do not use sheet plastic as a dust cover. A n ...

  • Honda Outboard Motor BF200A - page 83

    WITH OUTBOARD MOTOR INSTALLED ON BOAT When trailering a boat with the outboard motor attached, leave the engine in the normal running position, if possible. Use a motor support bar to prevent the outboard motor from moving ' while trailering the boat. Refer to the manufacturer's instructions for using a motor support bar. MOTOR SUPPORT BA ...

  • Honda Outboard Motor BF200A - page 84

    TAKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT START 1. Check emergency stop switch clip. 2. Check control positions. Possible Cause Correction Clip not inserted in stop switch. Insert clip in stop switch. Control lever not in neutral position. Shift to neutral. Fast idle lever raised (side-mount Leave fast idle lever OFF (p. 18 ). type). 82 ...

  • Honda Outboard Motor BF200A - page 85

    TAKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT START (continued) 3. Check fuel. Possible Cause Out of fuel. Fuel hose not primed. Fuel pump filter or fuel tank filter clogged. Bad fuel; boat stored without treating or draining gasoline, or refueled with bad gasoline. Correction Refuel (p. 67 ), Squeeze priming bulb (p. 31 ). Replace fuel filter ...

  • Honda Outboard Motor BF200A - page 86

    TAKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT START (continued) 4. Check battery. Possible Cause Correction Battery connections loose or connections. corroded. Clean and tighten battery Recharge battery. Battery discharged. ~~~ ~ ~ ~~~~~~~ 5. Check fuses. 1 Fuse(s) burnt out. I Replace fuse(s) (p. 87 ). 6. Remove and inspect spark plugs. Spark ...

  • Honda Outboard Motor BF200A - page 87

    TAKING CARE OF UNEXPECTED PROBLEMS HARD STARTING OR STALLS Correction Possible Cause AFTER STARTING 1. Check control positions. 2. Check fuel. Fast idle lever raised (side-mount type). Fuel hose not primed. Fuel pump filter or fuel tank clogged. Leave fast idle lever OFF (p. 18 ). Squeeze priming bulb (p. 31 ). Replace fuel filters (p. 69 ). Bad fu ...

  • Honda Outboard Motor BF200A - page 88

    TAKING CARE OF UNEXPECTED PROBLEMS HARD STARTING OR STALLS (continued) AFTER STARTING Possible Cause 3. Remove and inspect spark plugs. Spark plugs faulty, fouled or improperly gapped. 4. Take outboard motor to an Fuel system malfunction, fuel authorized Honda Marine dealer, etc. or refer to the shop manual. pump failure, ignition malfunction, Corr ...

  • Honda Outboard Motor BF200A - page 89

    TAKING CARE OF UNEXPECTED PROBLEMS BATTERY WILL NOT CHARGE AND ELECTRIC STARTER WILL NOT OPERATE The battery-charging (ACG) circuit and the electric starter relay circuit are protected by the 10, 15 and 30- ampere main fuses and 150-ampere ACG fuse. If the fuse burns out, the engine will not charge the battery, and the electric starter will not ope ...

  • Honda Outboard Motor BF200A - page 90

    TAKING CARE OF UNEXPECTED PROBLEMS Fuse FUSE (150A) FUSE CASE LID / SPARE FUSE Disconnect the battery cable at the battery negative (-) terminal before replacing the f use. Failure to do so may cause A short circuit. Replacement 1. Stop the engine. 2. Remove the engine cover. 3. Remove the fuse case lid. 4. Remove the old fuse by removing two 5 mm ...

  • Honda Outboard Motor BF200A - page 91

    TAKING CARE OF UNEXPECTED PROBLEMS OIL PRESSURE INDICATOR LIGHT GOES OFF AND ENGINE SPEED IS LIMITED Side-Mount Type Panel-Mount/Top-Mount Types If oil pressure becomes low, the green indicator light will go off, and the engine protection system will limit engine speed. If you are at cruising speed, engine speed will decrease gradually. Oil pressur ...

  • Honda Outboard Motor BF200A - page 92

    TAKING CARE OF UNEXPECTED PROBLEMS OVERHEATING INDICATOR LIGHT COMES ON AND ENGINE SPEED IS LIMITED Side-Mount Type Panel-Mount/Top-Mount Types 90 If the engine overheats, the red indicator light will come on, and the engine will stop in 20 seconds after the engine protection system will limit engine speed. If you are at cruising speed, engine spee ...

  • Honda Outboard Motor BF200A - page 93

    TAKING CARE OF UNEXPECTED PROBLEMS If there is no water flowing from the cooling system indicator, stop the engine, and tilt the outboard motor to inspect the water intake screens. If clogged, clean the water intake screens, return the outboard motor to the running position, restart the engine, and check the cooling system indicator again. If there ...

  • Honda Outboard Motor BF200A - page 94

    TAKING CARE OF UNEXPECTED PROBLEMS 3. Change the engine oil as described on p. 60 - 61 . If there was water in the engine crankcase, or if the used engine oil showed signs of water contamination, then a second engine oil change should be performed after running the engine for half an hour. 4. Remove the spark plugs (p. 64). Operate the starter to e ...

  • Honda Outboard Motor BF200A - page 95

    TECHNICAL INFORMATION Serial Number Locations Record the product identification number and engine serial numbers in the space provided on this page. You will need these numbers when ordering parts, and when making technical or warranty inquiries (p. 103 >. TECHNICAL AND CONSUMER INFORMATION PRODUCT IDENTIFICATION NUMBER 47 STERN BRACKET The prod ...

  • Honda Outboard Motor BF200A - page 96

    TECHNICAL AND CONSUMER INFORMATION Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, b ...

  • Honda Outboard Motor BF200A - page 97

    TECHNICAL AND CONSUMER INFORMATION You may use gasoline containing up to 5% methanol by volume, as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also damage.meta1, rubber, and plastic parts of your fu ...

  • Honda Outboard Motor BF200A - page 98

    TECHNICAL AND CONSUMER INFORMATION Emission Control System Information Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon ...

  • Honda Outboard Motor BF200A - page 99

    TECHNICAL AND CONSUMER INFORMATION Problems That May Affect Emissions If you are aware of any of the following symptoms, have your engine inspected and repaired by your servicing dealer. 0 Hard starting or stalling after starting. 0 Rough idle. 0 Misfiring or backfiring under load. 0 Afterburning (backfiring). Black exhaust smoke or high fuel consu ...

  • Honda Outboard Motor BF200A - page 100

    TECHNICAL AND CONSUMER INFORMATION Star Label A Star label was applied to this outboard motor in accordance with the requirements of the California Air Resources Board. The Star Label means Cleaner Marine Engine This engine has been certified as a: -1 0 0 t The Symbol for Cleaner Marine Engines: Cleaner Air and Water - for healthier lifestyle and e ...

  • Honda Outboard Motor BF200A - page 101

    TECHNICAL AND CONSUMER INFORMATION One Star Low Emission The one-star label identifies engines that meet the Air Resources Board’s 2001 exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted two-stroke engines. These engines are equivalent to the U.S. EPA’s 2006 standards for marine eng ...

  • Honda Outboard Motor BF200A - page 102

    TECHNICAL AND CONSUMER INFORMATION Specifications I Mnnm I Rc')nnA I Description Code 75.8 in 65.7 in 1 70.9 in Overall height 24.6 in (625 mm) Overall width 36.2 in (920 mm) Overall length LA 1 XA 1 XCA 1 XXA I XXCA Type BAEJ 1 BAEJ 1 BAFJ I BAEJ 1 BAFJ "I LVUm (1,670 mm) (1,925 mm) (1,800 mm) Transom height 30.0 in (762 mm) 25.0 in (635 ...

  • Honda Outboard Motor BF200A - page 103

    TECHNICAL AND CONSUMER INFORMATION Specifications MODEL Description Code Type Overall length Overall width Overall height Transom height Weight Rated power Full throttle range Engine type Displacement Spark plug gap (1,670 (1,800 rnrn) (1,925 rnrn) 20.0 in 25.0 in (635 rnrn) 30.0 in (762 rnrn) mrn) 589 Ibs 600 Ibs (272 kg) 611 Ibs (277 kg) (267 kn) ...

  • Honda Outboard Motor BF200A - page 104

    TECHNICAL AND CONSUMER INFORMATION BF200A & BF225A Tune up Spark plug gap See shop manual Intake: 0.22 k 0.02 mm Valve clearance (cold) See shop manual 650 * 50 rpm Idle speed See page 65 0.039-0.043in (1.00-1.10mm) Other specifications No other adjustments needed. Exhaust: 0.30 * 0.02 mm 102 ...

  • Honda Outboard Motor BF200A - page 105

    TECHNICAL AND CONSUMER INFORMATION CONSUMER INFORMATION Honda Publications These publications will give you additional information for maintaining and repairing your outboard motor. You may order them from your Honda marine dealer. Shop Manual This manual covers complete maintenance and overhaul procedures. It is intended to be used by a skilled te ...

  • Honda Outboard Motor BF200A - page 106

    INDEX Alternator (ACG) Indicator ............................................ 28 Anodes ............................................................................ 31 ARE YOU READY TO GET UNDER WAY ? 32 Replacement 73 Battery ............................................................................ 95 BATTERY WILL NOT CHARGE AND ELECTRIC STARTE ...

  • Honda Outboard Motor BF200A - page 107

    INDEX Fast Idle Lever ................................................................ 18 Fuel PRIMING ................................................................... 35 Priming Bulb .............................................................. 3 1 RECOMMENDATIONS ........................................... 68 Pump Filter Inspection and Replac ...

  • Honda Outboard Motor BF200A - page 108

    INDEX Oil Pressue Indicator ...................................................... 29 OIL PRESSURE INDICATOR LIGHT GOES OFF AND ENGINE SPEED IS LIMITED ............... 89 OPERATION ................................................................. 34 OTHER FEATURES ..................................................... 3 1 OUTBOARD MOTOR SAFETY ..... ...

  • Honda Outboard Motor BF200A - page 109

    Tachometer (optional equipment) .................................. 28 TAKING CARE OF UNEXPECTED PROBLEMS ..... 82 TECHNICAL AND CONSUMER INFORMATION ... 93 TECHNICAL INFORMATION .................................... 93 THE IMPORTANCE OF MAINTENANCE ................ 52 Throttle Button Panel-Mount Type ................................................. ...

  • Honda Outboard Motor BF200A - page 110

    t I f I I- I I I I II I 4 3: i i -u- I II ...

  • Honda Outboard Motor BF200A - page 111

    i6 1 m m I a t I 1 t a ...

  • Honda Outboard Motor BF200A - page 112

    0009-ZAZ- lEXOO 009ZAZ 1 E ...

Manufacturer Honda Category Boat

Documents that we receive from a manufacturer of a Honda Outboard Motor BF200A can be divided into several groups. They are, among others:
- Honda technical drawings
- Outboard Motor BF200A manuals
- Honda product data sheets
- information booklets
- or energy labels Honda Outboard Motor BF200A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honda Outboard Motor BF200A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honda Outboard Motor BF200A, service manual, brief instructions and user manuals Honda Outboard Motor BF200A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honda Outboard Motor BF200A.

Similar manuals

A complete manual for the device Honda Outboard Motor BF200A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honda Outboard Motor BF200A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honda Outboard Motor BF200A.

A complete Honda manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honda Outboard Motor BF200A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honda Outboard Motor BF200A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honda Outboard Motor BF200A, that we can find in the current document
3. Tips how to use the basic functions of the device Honda Outboard Motor BF200A - which should help us in our first steps of using Honda Outboard Motor BF200A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honda Outboard Motor BF200A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honda Outboard Motor BF200A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honda Outboard Motor BF200A?

Use the form below

If you did not solve your problem by using a manual Honda Outboard Motor BF200A, ask a question using the form below. If a user had a similar problem with Honda Outboard Motor BF200A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)