English dropdown-ico

Manual Grizzly G1030

26 pages 1.01 mb
Download

Go to site of 26

Summary
  • Grizzly G1030 - page 1

    DUST COLLECTOR MODEL G1030 INSTRUCTION MANUAL COPYRIGHT © 1991 BY GRIZZLY INDUSTRIAL, INC. REG # 3 176 555 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY 1999. PRINTED IN USA ...

  • Grizzly G1030 - page 2

    ...

  • Grizzly G1030 - page 3

    G1030 Dust Collector -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 ADDITIONAL SAFETY INSTRUCTIONS FOR THE DUST COLLECTOR ................4 2 . CIRCUIT REQUIREMENTS CONNECTION TO POWER SUPPLY .................................................. ...

  • Grizzly G1030 - page 4

    -2- G1030 Dust Collector Safety Instructions For Power Tools SECTION 1: SAFETY 7. DON’T FORCE TOOL . It will do the job better and safer at the rate for which it was designed. 8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi ...

  • Grizzly G1030 - page 5

    G1030 Dust Collector -3- 16. REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury. 18. CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or ...

  • Grizzly G1030 - page 6

    -4- G1030 Dust Collector Additional Safety Instructions For The Dust Collector 4. Suspended dust particles in conjunction with an ignition source, may cause an explosion. DO NOT operate the dust collector in areas where explosion risks would be high if dust were dispersed into the area. Areas of high risk include, but are not limited to, areas near ...

  • Grizzly G1030 - page 7

    G1030 Dust Collector -5- SECTION 2: CIRCUIT REQUIREMENTS The motor supplied with the G1030 requires 220V service and cannot be rewired for 110V. Under normal use, the motor draws approxi- mately 18 amps @ 220V. We recommend using a 20 amp circuit breaker or a 30 amp slow-blow fuse for 220V operation. This should be satisfactory for normal use, whil ...

  • Grizzly G1030 - page 8

    -6- G1030 Dust Collector Figure 1. Recommended 220V receptacle. Plug/Receptacle: We recommend using the plug type illustrated in Figure 1 . Contact your local electrical contractor’s supply, a licensed electrician or our service department if you have questions about the configuration for your specific situation. Serious personal injury may occur ...

  • Grizzly G1030 - page 9

    G1030 Dust Collector -7- Grizzly Industrial, Inc. is proud to offer the Model G1030 Dust Collector. These dust collectors are a part of Grizzly’s growing family of fine machin- ery. When used according to the guidelines set forth in this manual, you can expect years of trou- ble-free, enjoyable operation and proof of Grizzly’s commitment to cus ...

  • Grizzly G1030 - page 10

    -8- G1030 Dust Collector Unpacking The Model G1030 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its a ...

  • Grizzly G1030 - page 11

    G1030 Dust Collector -9- Site Considerations When placing the G1030 Dust Collector in your shop, two major considerations should be addressed: working clearances and electrical access and loading. 1. Working Clearances: Be sure to allow your- self sufficient room to safely operate your machines in any foreseeable operation. Consider existing and an ...

  • Grizzly G1030 - page 12

    -10- G1030 Dust Collector SECTION 4: ASSEMBLY Beginning Assembly Assembly of the G1030 is straightforward and can be accomplished quite easily. We have orga- nized the assembly process into logical steps. Please follow them in sequence. You will find that some pre-assembly has been done at the factory. For example, the motor and switch are already ...

  • Grizzly G1030 - page 13

    G1030 Dust Collector -11- Figure 3. Mounting collector to base. Figure 4. Mounting outlet to collector body. Collector Body The collector body includes the fan assembly, switch, motor and power cord which are pre- assembled at the factory. Set the collector body on top of the base plate so the intake portion is near the edge of the base plate and t ...

  • Grizzly G1030 - page 14

    -12- G1030 Dust Collector Collectors The left and right collectors attach to each side of the outlet flange and are later supported by the support bracket assembly. The inside of the col- lectors are funnel shaped and force the air around in a cyclone motion. Make sure that the inside taper (funnel) is facing downward and that the collector inlet f ...

  • Grizzly G1030 - page 15

    G1030 Dust Collector -13- Figure 8. Securing the bag to the collector Collection/Filter Bags bolt through one side of the clamp, then the lock nut, then thread the bolt through the other clamp. Figure 9 Hook the loops of the two upper filter bags over the upper support bracket. Figure 10. There are two collection bags which install onto the bottom ...

  • Grizzly G1030 - page 16

    -14- G1030 Dust Collector SECTION 6: OPERATIONS Please review the safety rules if you are not sure about the risks associated with operating this machine. Turn on the power supply at the main panel if not already on. Press the ON switch and be ready to switch OFF just in case there is a problem. The dust collector should run smoothly and be free of ...

  • Grizzly G1030 - page 17

    G1030 Dust Collector -15- For mobility, the G1030 is mounted on casters and can be moved within close proximity to your woodworking machines. You will need a flexible duct to connect each machine with a collection hood. If you wish to specifically direct air flow while the dust collector is attached to more than one machine, you will need to add a ...

  • Grizzly G1030 - page 18

    -16- G1030 Dust Collector System Grounding Since plastic hose is abundant, relatively inex- pensive, easily assembled, and airtight, it is a very popular material for conveying dust from woodworking machines to the dust collector. We recommend using flexible hose (flex-hose) to connect the woodworking machine to the dust collector. However, plastic ...

  • Grizzly G1030 - page 19

    G1030 Dust Collector -17- SECTION 7: MAINTENANCE Lubrication Impeller Tightening Periodic maintenance will ensure safe operation, long dust collector life, and low overall cost of operation. General ...

  • Grizzly G1030 - page 20

    -18- G1030 Dust Collector SECTION 8: CLOSURE The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1030 Dust Collector. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained servi ...

  • Grizzly G1030 - page 21

    G1030 Dust Collector -19- Design Type ...................................................................................................... Floor Model Specifications: Intake Hole Size ..........................................................................................................6" Intake Adapter Hole Size (1)...................... ...

  • Grizzly G1030 - page 22

    REF PART # DESCRIPTION 1 P1028001 CASTER 2 PFB01 FLANGE BOLT 5 ⁄ 16 "-18 x 1 ⁄ 2 " 3 P1030003 BASE PLATE 4 PS06 PHLP HD SCREW 10-24 x 3 / 8 " 5 P1030005 INLET COVER 6 P1028007 CAP SCREW M6-1 x 19 LH 7 PB09 HEX BOLT 5 ⁄ 16 "-18 x 1 ⁄ 2 " 8 P1028009 SPECIAL WASHER 9 P1029010 TURBO FAN 10 P1028011 COLLECTOR BODY 11 PW0 ...

  • Grizzly G1030 - page 23

    2 ...

  • Grizzly G1030 - page 24

    -22- G1030 Dust Collector Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written war ...

  • Grizzly G1030 - page 25

    10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt Sander ___Mini Jointer ___Other_________ ...

  • Grizzly G1030 - page 26

    FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

Manufacturer Grizzly Category Dust Collector

Documents that we receive from a manufacturer of a Grizzly G1030 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- G1030 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly G1030
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly G1030.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly G1030, service manual, brief instructions and user manuals Grizzly G1030. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly G1030.

Similar manuals

A complete manual for the device Grizzly G1030, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly G1030 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly G1030.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly G1030 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly G1030, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly G1030, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly G1030 - which should help us in our first steps of using Grizzly G1030
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly G1030
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly G1030 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly G1030?

Use the form below

If you did not solve your problem by using a manual Grizzly G1030, ask a question using the form below. If a user had a similar problem with Grizzly G1030 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)