English dropdown-ico

Manual Fujitsu FI-5015C

90 pages 2.65 mb
Download

Go to site of 90

Summary
  • Fujitsu FI-5015C - page 1

    P3PC-1592-05ENZ0 Operator's Guide fi-5015C Image Scanner ...

  • Fujitsu FI-5015C - page 2

    fi-5015C Image Scanner Operator’s Guide i CONTENTS ■ Regulatory Information ........................................................ iii ■ Note, Liability ............ ............................................................. v ■ Safety Precautions ... .................................... ...................... viii Chapter 1 NAME OF PA ...

  • Fujitsu FI-5015C - page 3

    ii Chapter 4 TROUBLES HOOTING ......... .................................. 53 4.1 Error Indications in the Fu nction Number Display ........ 54 4.2 Troubleshooting .... .................................... ....................... 56 APPENDIX A SCANNER SPECI FICATIONS ............. ........................ AP-1 APPENDIX B Using [Scan] or [Send to] b ...

  • Fujitsu FI-5015C - page 4

    fi-5015C Image Scanner Operator’s Guide iii INTRODUCTION Thank you for purcha sing th e fi-5015C Color Scanner. This document describ es how to han dle fi-5015C and basic operation methods. Before you start using fi- 5015C be sure to thoro ughly read this manual to en sure correct use. This document describe s the basic operation metho ds to perf ...

  • Fujitsu FI-5015C - page 5

    iv Canadian DOC Regulations This digital apparatus does not exceed the Class B limit for radi o noise emissions from digital apparatus set out in the Radio interference Re gulations of the Canadian Dep artment of Communications. This Class B digital apparatus complies with Canadian ICES-003. Le présent appareil numérique n'émet pas de paras ...

  • Fujitsu FI-5015C - page 6

    fi-5015C Image Scanner Operator’s Guide v ■ Note, Liability READ ALL OF THIS MANUAL CAREFULL Y BEFORE USING THIS PRODUCT . IF THIS PRODUCT IS NOT USED CORRECTL Y , UNEXPECTED INJUR Y MA Y BE CAUSED TO USERS OR BYST ANDERS. Also, keep this manual in a safe place so that it can be easily refe rred to during use of this product. While all efforts ...

  • Fujitsu FI-5015C - page 7

    vi How T rademarks Are Indicated In This Manu al References to operating systems (OS) are indicated as follows: Where there is no distinction betw een the dif ferent ve rsions of the abov e operating s ystem, the gen eral term "W indows" is used. All the descriptions in this manual assume the us age of Adobe Acrobat bundled with this prod ...

  • Fujitsu FI-5015C - page 8

    fi-5015C Image Scanner Operator’s Guide vii W arning Indications Used In This Manual Symbols Used In This Manual Screen Examples In This Manual The screen examples in this manual are subject to change without notice in th e interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by ...

  • Fujitsu FI-5015C - page 9

    viii ■ Safety Precautions In the following warnings, "power cable" may refe r to the AC cable connected to the AC adapter collectively . Do not damage the A C cable . Use only specified A C ca bles and connector cables Use this scanner only at the in dicated po wer v oltage . Do not connect to m ultiple-power strips. Do not touch the A ...

  • Fujitsu FI-5015C - page 10

    fi-5015C Image Scanner Operator’s Guide ix Do not install the de vice in loca tions that has oil smoke, steam, humidity , and dust. T urn the scanner OFF if it is damaged. Do not put liquids inside the sc anner . Do not touch the inside of the scanner unless necessary . Do not use the scanner if there is a strange odor . Do not use aer osol spra ...

  • Fujitsu FI-5015C - page 11

    x Do not install the scanne r on unstable surfaces. Do not bloc k the ventilation por ts. Do not place heavy objects or stand on top of the scanner . Firmly i nser t the power plug. A v oid an y contact when scanner is in use. Do not use the scanner immediatel y after mo ving it from a cold place into a warm r oom. Make sure that the scanner is ins ...

  • Fujitsu FI-5015C - page 12

    fi-5015C Image Scanner Operator’s Guide xi Bef ore mo ving the scanner , disconnect the power plug fr om the power out let. Pr otect the scanner from static electricity . Disconnect the power plug fr om th e power outl et when the scanner is not used f or a long period of time . Do not install the scanner in the direct sunlight. Bef ore mo ving t ...

  • Fujitsu FI-5015C - page 13

    xii ...

  • Fujitsu FI-5015C - page 14

    1 fi-5015C Image Scanner Operator’s Guide 1 Chapter 1 NAME OF P ARTS This chapter shows the exterior view and the name of each part to descrive its fu nction. 1.1 Units .......................................................................... .......................................... .. ... 2 1.2 Operator Panel ................................. ...

  • Fujitsu FI-5015C - page 15

    2 1.1 Units 1. Front side Part Function 1. Automatic docu- ment feeder (ADF) Automatically feeds docume nts one by one to the reading position in th e scanner. 2. Side guides Holds the docume nts straight. 3. ADF paper chute Holds the documents to be fed by th e automatic docume nt feeder (ADF). 4. Extension Extended when long documents are set. 5. ...

  • Fujitsu FI-5015C - page 16

    1.1 Units fi-5015C Image Scanner Operator’s Guide 3 NAME OF P AR TS 1 2. Flatbed 3. Backside Part Function 1. Document holding pad Holds the docume nt on Flatbed. 2. Document bed On which the document is set face down. Part Function 1. USB conn ector Connects USB cable to PC. 2. ADF cable connector Connects the cable from ADF. 3. DC inlet Connect ...

  • Fujitsu FI-5015C - page 17

    4 4. Side (ADF side) Part Function 1. Shipping lock Locks the scanning head to prevent the scanner damaged when movi ng or transporting. 1 Unlocked Locked ...

  • Fujitsu FI-5015C - page 18

    1.2 Operator Panel fi-5015C Image Scanner Operator’s Guide 5 NAME OF P AR TS 1 1.2 Operator Panel Part Function 1. Function button Changes the function activated by [Send to] button. 2. Function number display Indicates the function number or erro r status. For detail refer "4.1Error Indications in the Function Number D isplay" on page ...

  • Fujitsu FI-5015C - page 19

    6 ...

  • Fujitsu FI-5015C - page 20

    2 fi-5015C Image Scanner Operator’s Guide 7 Chapter 2 BASIC SCANNER OPERA TIONS This chapter describes how to turn On/Off the scanner, and ho w to load/scan the documents. In this chapter Windows XP screenshots are illustrated. The screens and operations may differ slightly if the OS you are using is not Windows XP. Also, when TWAIN is updated th ...

  • Fujitsu FI-5015C - page 21

    8 2.1 Turning ON/OFF the Scanner 1. Turning the Power On Switch on the Main Power switch located on th e side. Then press [Power] button on the operator Panel. The scanner is turned ON, and the gr een LED on the operator panel lights. During the initialization, the indication of the Function Number Disp lay changes as follows: “8”->"P&q ...

  • Fujitsu FI-5015C - page 22

    2.1 Turning ON/OFF the Scanner fi-5015C Image Scanner Operator’s Guide 9 BASIC SCANNER OPERA TIONS 2 2) Double click the "Printer and Other Hardwa re" icon on the Control panel of your PC. ⇒ The [Printer and Other Hardware] window appears. 3) On the [Printers and Other Hardware] window, double click the [Scanners and Cameras] icon. ? ...

  • Fujitsu FI-5015C - page 23

    10 ⇒ The [fi-5015C P roperties] dialog bo x appears. 5) Click the "Device Set" tab. ⇒ The following panel appears. 2. Click [Power Control] button ⇒ The following scre en is displayed. ...

  • Fujitsu FI-5015C - page 24

    2.1 Turning ON/OFF the Scanner fi-5015C Image Scanner Operator’s Guide 11 BASIC SCANNER OPERA TIONS 2 3. In this screen, • To power on/off the scanner by p ressing the Power button: ⇒ select "Enable power switch". • To power on/off the scanner by connecting or disconnecting the AC cable: ⇒ select "Disable power switch" ...

  • Fujitsu FI-5015C - page 25

    12 2.2 Loading Documents on ADF This section explains how to ch eck the document cond ition and load them on ADF. These opera- tions are very importa nt to avoid paper jam or sc anning error. 2.2.1 Checking document condition Check that the document m eets the following condition. ■ Document Size ■ Document Type The following paper types are re ...

  • Fujitsu FI-5015C - page 26

    2.2 Loading Do cuments on ADF fi-5015C Image Scanner Operator’s Guide 13 BASIC SCANNER OPERA TIONS 2 • Documents that are not square or rectangular • Very thin documents • Photographs Do not use the fo llowing documents: • Paper-clipped or stapled documents • Documents on which the ink is still wet • Documents other than paper such as ...

  • Fujitsu FI-5015C - page 27

    14 HINT When using the ADF, the leadin g edge of all document sheets mu st be evenly aligned. Make sure that curling at the lea ding edge is within the following tolerances: More than 30 m m F eed d ir ec ti on R ead su rf ace To p of the p a p e r L ess th an 3mm F eed d ir ec ti on Read surface Top of the paper L ess th an 5mm ...

  • Fujitsu FI-5015C - page 28

    2.2 Loading Do cuments on ADF fi-5015C Image Scanner Operator’s Guide 15 BASIC SCANNER OPERA TIONS 2 2.2.2 Loading documents on ADF This section explains how to load documents on ADF . 1. Align the edges of the docu ments. 1) Grasp no more than 50 sheets in a stack. 2) Confirm that all the docu ments have the same width. 2. Fan the documents as f ...

  • Fujitsu FI-5015C - page 29

    16 4. Load the documents on the ADF paper chute. 5. Adjust the side guides to the width of t he documents. Move the side guides so that they touch both sid es of the docu ments. If there is any clearance between the side gu ides and the edges of documents, the scanned image may be ske wed. 6. Scan the documents. For how to scan the document, refer ...

  • Fujitsu FI-5015C - page 30

    2.3 Loading Document on Flatbed fi-5015C Image Scanner Operator’s Guide 17 BASIC SCANNER OPERA TIONS 2 2.3 Loading Document on Flatbed 1. Open the docu ment cover. 2. Place the document on the document bed (glass) with f ace down. 3. Position the document so that the upp er-left corner of the documen t is aligned with the reference mark of the do ...

  • Fujitsu FI-5015C - page 31

    18 ■ Document Size Orientation of the docume nt an d how to set Paper size shall be as follows for Portrait scan- ning or Landscape scanning . For Flatbed: Minimum 26 (Width ) x 26 (Length) mm (1 x 1 in.) Maximum 216 (Width ) x 297 (Length) mm (8.5 x 11.7 in.) [Portrait] [Landscape] • Paper Size setting Select Paper Size among A4, A5, B5, Lette ...

  • Fujitsu FI-5015C - page 32

    2.4 Scanning Documents fi-5015C Image Scanner Operator’s Guide 19 BASIC SCANNER OPERA TIONS 2 2.4 Scanning Documents This section explains how to scan document s using ScandAll PRO as an example. 1. Load documents on the scanner. For details about loading documents, refer to "2 .2 Loading Documents on ADF" on page 12 or "2.3 Loadin ...

  • Fujitsu FI-5015C - page 33

    20 6. Set the scan type, paper size (see below), etc., an d click the [OK] button. For details on settings in the [TWAIN Driver] dialog box, re fer to "2.5 How to use the Scan- ner Driver" on page 22 ⇒ You are returned to the [Scan Settings] dialog box. 7. Click the [Scan] button. HINT When you are using TWAIN, you may see the TWAIN Dri ...

  • Fujitsu FI-5015C - page 34

    2.4 Scanning Documents fi-5015C Image Scanner Operator’s Guide 21 BASIC SCANNER OPERA TIONS 2 ⇒ The images of scanned docu ments are displayed on the [ScandAll PRO] window. For details on functions and operations of Sc andAll PRO, refer to the description in the [Help] menu. ...

  • Fujitsu FI-5015C - page 35

    22 2.5 How to use the Scanner Driver ■ TWAIN Scanner Driver TWAIN Scanner Driver is designed for scanning documents with FUJI TSU image scanner fi series by using application software that complies with the TWAIN standard. The following describes th e procedure with examples of Scan dAll PRO for ordinary scanning by using this driver. 1. Procedur ...

  • Fujitsu FI-5015C - page 36

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 23 BASIC SCANNER OPERA TIONS 2 6) Configure settings for scanni ng and click the [OK] button. For details about the settings on this wi ndow, refer to "Settin g Window for TWAIN Scanner Driver" on page 25. ⇒ You are returned to the [Scan Settings] dialog box. 7) ...

  • Fujitsu FI-5015C - page 37

    24 ⇒ The images of scanned documents are disp layed on the [ScandAll PRO] window. With ScandAll PRO, the scanned image will not be displayed when you clear the [Display scanned imag es immediately after scanning] ch eck box in the [Scan Settings] dialog box. 8) Save the scanned ima ges. The scanned image is saved when the [Save to file] check box ...

  • Fujitsu FI-5015C - page 38

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 25 BASIC SCANNER OPERA TIONS 2 2. Setting Window for TWAIN Scanner Driver You can set the TWAIN Scanner Driver on this window. The following describes the main setting items. • For details on each functions, refer to "TWAIN Scanner Driver He lp" (appears by pres ...

  • Fujitsu FI-5015C - page 39

    26 Image Mode Specifies the image type for the scanned documents. [Scan] button Starts scanning documents with the current settings. [Preview] button Documents are scanned preliminar ily before the actual scanning. You can confirm th e image of the documents in the preview window. [Close ] butt on Saves the current settings and closes this window. ...

  • Fujitsu FI-5015C - page 40

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 27 BASIC SCANNER OPERA TIONS 2 [Option...] button You can set up the deta ils of optio nal functions on the window below. [Rotation] tab Select this tab when setting image rotation. [Job/Cache] tab Select this tab when setting cache mode, blank page skipping, etc. [Generic] ...

  • Fujitsu FI-5015C - page 41

    28 ■ ISIS Scanner Driver ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application software that complies with the ISIS standard. The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver. The procedure may vary depending on your application. ...

  • Fujitsu FI-5015C - page 42

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 29 BASIC SCANNER OPERA TIONS 2 5) Select the profile for scanning. • When creating a new profile Select one from al ready existing prof iles and click [Add Profile...] button. ⇒ A new profile will be created based on the profile you select. • When changing the setting ...

  • Fujitsu FI-5015C - page 43

    30 7) Configure settings for scanni ng and click the [OK] button. For details on this dialog bo x, refer to "Configuration Window of ISIS Scanner Driver" on page 31. 8) The [Profile Editor] window appears. Click the [OK] button to return to [New batch] dialog. 9) Load the documents on the scanner. 10) Click the [Scan] button. ⇒ Scanned ...

  • Fujitsu FI-5015C - page 44

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 31 BASIC SCANNER OPERA TIONS 2 2. Configuration Wind ow of ISIS Scanner Driver "Main" tab Mode Selects a color mode suitable for the purpose from the menu. Dots per inch Specifies the number of pixels (dots) per inch. Select a fixed resolutio n from the list (75, ...

  • Fujitsu FI-5015C - page 45

    32 Brightness Sets the brightness of the entire image. Spec ify the brightness as a number within the range of 1 (dark) to 128 (bright). To brighten the entire image, inc rease the value of the setting. To darken the enti re image, decrease the value. Contrast Sets the contrast between light and shadow of the scanned image. Spec ify the contrast as ...

  • Fujitsu FI-5015C - page 46

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 33 BASIC SCANNER OPERA TIONS 2 [Scan Area...] button Opens the Scan Area dialog box. Speci fy scan area for the document size. The size can be set by dragging the frame w ith mouse. Otherwise, enter any value for the setting. ...

  • Fujitsu FI-5015C - page 47

    34 "More" tab Opens [More Settings] window. Used for setting advanced features. Use Advanced DTC This option scans any kind of documents by binary processing to produce data with good scanning quality. Documents containing thin letters, charact ers with the colored background, and co lored charts cannot be scan ned sufficiently clearly by ...

  • Fujitsu FI-5015C - page 48

    2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 35 BASIC SCANNER OPERA TIONS 2 "Gamma" tab Download You can download and use any Gamma pattern. Custom You can specify the numeric values of items such as “Gamma”, “Brightness”, “Con- trast”. "About" tab Displays the version number of IS IS d ...

  • Fujitsu FI-5015C - page 49

    36 2.6 Image Scanning Application This section explains about the bundled "Scand All PRO" image scanning application, which is used as an example to explain the procedures in this manual. ScandAll PRO supports both TWAIN and ISIS drivers. By defining scan settings as profiles, you can customize the settings according to your preference. ...

  • Fujitsu FI-5015C - page 50

    3 fi-5015C Image Scanner Operator’s Guide 37 Chapter 3 MAINTENANCE This chapter describes how to clear the paper jam, perform daily main tenance and cleaning. Do not use aer osol spra ys near the scanner Do not use any aerosol sprays or alcohol based spra ys to clean the scanner . Dust blown up by strong air from the spray may enter the inside of ...

  • Fujitsu FI-5015C - page 51

    38 3.1 How to clear the paper jam When a paper jam occurs while using ADF, follow the procedure below to remove jammed paper. 1) Remove the documents from the ADF paper chute. 2) Open the AD F. . 3) Remove the jam med paper. 4) Close the ADF completely until it clicks. Be careful not to get injured wh en removing jammed documents. Be careful, the A ...

  • Fujitsu FI-5015C - page 52

    3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 39 MAINTENANCE 3 3.2 Cleaning To keep scanner performance stable, clean the scanner and re place the consumable if necessary as follows. 3.2.1 Cleaning Materials For details about the cleaning ma terials, contact the FUJITSU scanner dealer where you pur- chased the scanner. *1) It may take long ...

  • Fujitsu FI-5015C - page 53

    40 3.2.2 Cleaning the Flatbed ■ Cleaning Method 1. Open the docu ment cover. 2. Clean the following locations usin g a so ft, dry cloth moistened with cleaning fluid. • Document holdin g pad - 1 Wipe gently. • Document bed - 2 Wipe lightly. 3. Wait for cleaned parts to dry. 4. Gently close th e document cover. ATTENTION • Detergent for clea ...

  • Fujitsu FI-5015C - page 54

    3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 41 MAINTENANCE 3 3.2.3 Cleaning the ADF Clean the ADF every 1,000 scans. Note that this guideline varies accordi ng to the type of documents you are scanning. For example, it may be n eces sary to clean the ADF more fre quently if documents are scanned when the toner is not sufficiently fixed o ...

  • Fujitsu FI-5015C - page 55

    42 • Pad ASSY Wipe Pad ASSY with the cloth in the direction from bottom to top. • Pick roller unit Wipe the Pick roller unit by moving the cloth from side to side of rollers. Rotate the rollers forward with your finger and repeat the wipin g procedure until all surface of ro ller are cleaned. • Pinch rollers Clean Pinch roller softly not to d ...

  • Fujitsu FI-5015C - page 56

    3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 43 MAINTENANCE 3 4. Open the Flatbed cover and clean th e following locations. ATTENTION The glass surface under the ADF become s hot during the oper ation of the scanner. ...

  • Fujitsu FI-5015C - page 57

    44 3.3 Replacing Consumable 3.3.1 Part number and Replacement cycle The following table lists the consum able used in the scanner. Be su re to keep some consumables in stock. The customer is required to replace consumable periodic ally. Otherwise, the scanner may not func- tion properly. Part nu mber and re commended replacement cycle is, Replaceme ...

  • Fujitsu FI-5015C - page 58

    3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 45 MAINTENANCE 3 3.3.2 Guidelines for Cons umable Replacement Cycle With this product, you can le arn how many times the consumab les are used so that you can estimate the right timing for the replacement. 1. When turning on the power, check that the sca nner is connected to your PC ...

  • Fujitsu FI-5015C - page 59

    46 ⇒ The [fi-5015C Properties] dialog box appears. 5. Click the "Devi ce Set" tab. ⇒ The following panel appears. You can confirm the following information on this panel: • Total number of scans with ADF and Flatbed. • Pad and Pick roller counter (approximate number of scans after resetting the counter) ...

  • Fujitsu FI-5015C - page 60

    3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 47 MAINTENANCE 3 The following message may appear while using the scanner: Replace consumables when this message is displayed. After clicking the [Ignore] button, this messa ge will disappea r and scanning will continue . Please replace the consumable as soon as possible. As a defau ...

  • Fujitsu FI-5015C - page 61

    48 3. Remove the snap-in Pad ASSY by pinching the upper part of the pad clamp as shown in the following photo. 4. Install new Pad ASSY by the revers e procedure of removing. 5. Press the center of the ADF to close it until it clicks. 6. Reset the pad cou nter. 1) Check that the scanner is connected to your PC and turn on the scanner. 2) Open the [S ...

  • Fujitsu FI-5015C - page 62

    3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 49 MAINTENANCE 3 4) Click the "Device Set" tab. 5) After clicking the [Clear] button beside "P ad" in "Page Counter", click the [OK] button. ⇒ The following wind ow appears. Click the [OK] button. The Pad counter returns to "0". ...

  • Fujitsu FI-5015C - page 63

    50 3.3.4 Replacing the Pick roller unit 1. Remove all documents from the ADF pape r chute. 2. Open the ADF. 3. Remo ve the Pick ro ller unit from the scanner. 1) Pinch the fixture with your fi ngers with another hand holding the Pick roller unit. Be careful, the ADF may close and pinch your fingers. ...

  • Fujitsu FI-5015C - page 64

    3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 51 MAINTENANCE 3 2) Pull the Pick roller unit to the fixture‘s side. ⇒ The Pick roller unit is removed downward s. 4. Attach a new Pick roller unit to the sca nner. Attatch a new Pick roller unit to the scanner in reverse order of removing. 1) Set the Pick roller unit inserting ...

  • Fujitsu FI-5015C - page 65

    52 5. Press the center of the ADF to close it until it clicks. 6. Reset the Pick roller counter. 1) Check that the scanner is connected to your PC and turn on the scanner. 2) Open the [Scanners and Cameras] from the control panel of your PC. 3) Open the [Properties] of [fi-501 5C] from the [Scanners and Cameras]. ⇒ The [Properties of fi-5015C] di ...

  • Fujitsu FI-5015C - page 66

    4 fi-5015C Image Scanner Operator’s Guide 53 Chapter 4 TROUBLESHOOTING This chapter describes how to remedy tro ubles and items to check before contacting the agent where you bought the scanner. 4.1 Error Indications in the Function Number Display ............................................ 54 4.2 Troubleshooting ................................ ...

  • Fujitsu FI-5015C - page 67

    54 4.1 Error Indications in the Function Number Display When any error occurs, the operat or panel indicates "U" followed by a number alternately for tem- porary errors, or "E" followed by a numb er for device alarms (permanent error). Temporary errors can be resolved by the operator, but the de vice ala rm requires recovery w o ...

  • Fujitsu FI-5015C - page 68

    4.1 Error Indications in t he Function Number Display fi-5015C Image Scanner Operator’s Guide 55 TR OUBLESHOO TING 4 ■ Device alarms: A number appearing in alternation following the "E" refers to th e follo wing type of device alarms: Indication Meaning Solution E0 Shipping lock error occurred. C onfirm that the shipping lock is relea ...

  • Fujitsu FI-5015C - page 69

    56 4.2 Troubleshooting If a problem occurs, check the following items befo re contacting the manufacturer's authorized ser- vice center. Be careful, the inside of ADF (automatic document feeder) may become hot during th e operation. Symptom Check this item Remedy Scanner does not turn on. Is the main switch turned on? Turn the main swit ch on. ...

  • Fujitsu FI-5015C - page 70

    4.2 Troubleshooting fi-5015C Image Scanner Operator’s Guide 57 TR OUBLESHOO TING 4 * "Multi feed" means that more than 2 papers are fed at the same time. Multi feed* frequently occurs. Does the document satisfy the "Doc- ument Quality" described in Section 2.2.1? Scan the documents by Flatbed. Are the documents set properly in ...

  • Fujitsu FI-5015C - page 71

    58 ...

  • Fujitsu FI-5015C - page 72

    fi-5015C Image Scanner Operator’s Guide AP-1 A APPENDIX A SCANNER SPECIFICA TIONS ■ Basic Specifications Item Specifications Dimension (mm) Width Depth Height 328 (12.9 in.) 447 (17.6 in.) 175 (6.9 in.) Weight(kg)/lb 5.5 (11.7 lbs) Input power Voltage AC100 to 240V Phases Single Frequency 50 / 60Hz Power consump- tion During operation 24W or le ...

  • Fujitsu FI-5015C - page 73

    AP-2 ■ Dimensions Unit: millimeters 175 447 (17.6 in.) (6.88 in.) 175 328 (12.9 in .) (6.88 in.) ...

  • Fujitsu FI-5015C - page 74

    fi-5015C Image Scanner Operator’s Guide AP-3 B APPENDIX B Using [Scan] or [Send to] button ■ Settings on the Personal Computer By setting the link of the application software to t h e [Scan] or [Send to] button, yo u can launch the linked application b y si mply pushing the button. 1. Select [Start]-[Control Panel]. 2. Select [Scanners and Came ...

  • Fujitsu FI-5015C - page 75

    AP-4 5. Select the application with its process, excuted by th e event. For the case of Windows XP, click [Start this program] under [Acti ons] and select the application and process from the menu. 6. Click the [OK] button. If you are using ScandAll PRO, refer to "ScandAll PRO V2.0 User's Guide". HINT The window and op erations may v ...

  • Fujitsu FI-5015C - page 76

    fi-5015C Image Scanner Operator’s Guide AP-5 B ■ Settings on the Scanner • To use the [SCAN] button : You can use this button as is; no special settings are required. ⇒ Simply pressing the [SCAN] button starts the linked application. • To use the [Send to] button : Press the [Functi on] button to change the number on the function numb er ...

  • Fujitsu FI-5015C - page 77

    AP-6 ...

  • Fujitsu FI-5015C - page 78

    fi-5015C Image Scanner Operator’s Guide AP-7 C APPENDIX C GLOSSARY OF TERMS A4 size A standard p aper size. Paper size is 210 x 297 mm. A5 size A standard p aper size. Paper size is 148 x 210 mm. A6 size A standard p aper size. Paper size is 105 x 148 mm. A7 size A standard p aper size. Paper size is 74 x 105 mm. A8 size A standard p aper size. P ...

  • Fujitsu FI-5015C - page 79

    AP-8 A utomatic siz e/skew detection A function that automatically detect s the doc ument s' pag e size and adjust s output dat a to the detected page size. Document skewing is automatically detected and corrected for the output image. Brake r oller A roller that prevents two or more sheet s of pa per from being fed simult aneously into the AD ...

  • Fujitsu FI-5015C - page 80

    fi-5015C Image Scanner Operator’s Guide AP-9 C Default settings Pre-set values for optional menus. Density In this manual, refers to a me asurement of the depth of the display . Dither The process by which a group o f dots is ar ranged to represent a sha de of gray . The pre- determined dot p attern simulates shades of gray . This scanning proces ...

  • Fujitsu FI-5015C - page 81

    AP-10 Equipment Erro r An error that cannot be fixed by the op erator . The operator should call the manufa cturer for service. Err or diffusion High-quality half tone (pseudo-g rayscale) image production based on black-and-wh ite pixel binarization. A pixel's o ptical density and that of adjacent pixels are summed, with black pixels relocated ...

  • Fujitsu FI-5015C - page 82

    fi-5015C Image Scanner Operator’s Guide AP-11 C Flatbed An input device of the scanner , where documents are placed and scan ned. Generally used for scanning pages out of a book, or p aper th at is out of the feeding specification of the ADF . Also used to scan a small volume of document s by manual operation. Gamma A unit of changes of images&ap ...

  • Fujitsu FI-5015C - page 83

    AP-12 IPC preset mode While reading binary images, it is necessary to set th e scanner according to the quality of the sheet to be read. In this mode, these settings can be performed in advance by cor- responding each setting to a p attern number . ISIS (Image Scanner Inte rface Specification) A standard of API (App lication Program Interf ace) or ...

  • Fujitsu FI-5015C - page 84

    fi-5015C Image Scanner Operator’s Guide AP-13 C Mirr or image The read image is symmetrica lly flipped to produce a mirror image o f the original detected in the main scanning d irection. Moire P atterns Recurrent pattern s on scanned images caused by incorrect settings of angle s. Noise remo v al Isolated noise from an image appearing as black s ...

  • Fujitsu FI-5015C - page 85

    AP-14 Photograph mode (White level f o llower OFF) Selecting photograph mode makes brightness and contrast settings e ffective but pre- vents the threshold from bein g set. With photograph mode, the darkness of image corre- sponds to the black-pixel density , making it suitable in scanning ima ges such as photographs having gradations. Pic k roller ...

  • Fujitsu FI-5015C - page 86

    fi-5015C Image Scanner Operator’s Guide AP-15 C Separation r oller A roller that separa tes the sheet s of pap er from each other . Simplex reading mode A mode for scanning only the front side o f the document. Smoothing A process that eliminates "jaggies" from sl anted lines and curves. Irregular convexities are deleted and irregular c ...

  • Fujitsu FI-5015C - page 87

    AP-16 TW AIN (T echnology Without An y Interesting Name) A standard for API (App lication Program Interf ace) or proto col fo r imaging devices (scan- ners, digital camera s, etc.) developed by TW AIN Working Group. In order to use devices that comply with this st andard, it is necessary to inst all driver software based on the same standard. Ultra ...

  • Fujitsu FI-5015C - page 88

    fi-5015C Image Scanner Operator’s Guide IN-1 INDEX A ADF (automatic document feeder) ............ 2 C Checking document condition ................. 12 Cleaning Materials .................................. 39 Cleaner F1 ........................................ 39 Configuration Window of ISIS Scanner Driver ........................................ ...

  • Fujitsu FI-5015C - page 89

    IN-2 U USB connector .............................. ............ 3 Using the (Scan) or (Send to) button ....... . 3 ...

  • Fujitsu FI-5015C - page 90

    z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatso ever for any damages resulting from the use of this scanner a nd procedures described in this manual, profit loss due to defects, and any claims by a third party. z Copying of the contents of this manual in whole or in part and copying of the scan ...

Manufacturer Fujitsu Category Photo Scanner

Documents that we receive from a manufacturer of a Fujitsu FI-5015C can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- FI-5015C manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu FI-5015C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu FI-5015C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu FI-5015C, service manual, brief instructions and user manuals Fujitsu FI-5015C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu FI-5015C.

Similar manuals

A complete manual for the device Fujitsu FI-5015C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu FI-5015C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu FI-5015C.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu FI-5015C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu FI-5015C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu FI-5015C, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu FI-5015C - which should help us in our first steps of using Fujitsu FI-5015C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu FI-5015C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu FI-5015C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu FI-5015C?

Use the form below

If you did not solve your problem by using a manual Fujitsu FI-5015C, ask a question using the form below. If a user had a similar problem with Fujitsu FI-5015C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)