English dropdown-ico

Manual Kenwood LZ-701W

18 pages 1.58 mb
Download

Go to site of 18

Summary
  • Kenwood LZ-701W - page 1

    LZ-701W 7-inch WIDE SCREEN MONITOR INSTRUCTION MANUAL MONITEUR GRAND ECRAN 7 pouces MODE D’EMPLOI 7-Zoll BREITBILD MONITOR BEDIENUNGSANLEITUNG 7 inch BREEDBEELDMONITOR GEBRUIKSAANWIJZING MONITOR A SCHERMO AMPIO 7 pollici ISTRUZIONI PER L ’USO MONITOR DE P ANT ALLA P ANORÁMICA DE 7 pulgadas MANUAL DE INSTRUCCIONES MONITOR DE ECRÃ LARGO de 7 po ...

  • Kenwood LZ-701W - page 2

    English 2 Contents Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Switching the Monitor’ s Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Kenwood LZ-701W - page 3

    3 Safety Precautions To prevent injury and/or fire, take the following precautions: • Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition or ground wires, make sure to use automotive-grade wires or other wires with an area of 0.75mm 2 (A WG18) or more to ...

  • Kenwood LZ-701W - page 4

    English 4 Operation Power Tu rning on the power Press the V .SEL button. Tu rning off the power Press the V .SEL button for at least two seconds. Switching the Monitor’ s Picture <When the KTC-V800N or KTC-V800P is connected> Each time you press the V .SEL button, the monitor’ s picture switches as follows: ∞ [TV]: T elevision picture ? ...

  • Kenwood LZ-701W - page 5

    5 Y ou cannot operate when the navigation picture is displayed. <When the KTC-V800N or KTC-V800P is connected> Adjusting the Picture Quality Press the SCRN button, the picture quality adjustment screen to be displayed. Each time you press the SCRN button, the adjustment item can be selected.. Press the [ 2 ] or [ 3 ] button to adjust the valu ...

  • Kenwood LZ-701W - page 6

    Selecting the Channels <When the KTC-V800N or KTC-V800P is connected> Auto Seek Mode (AUTO1) Press the [ 3 ] button to seek for channels up the band. Press the [ 2 ] button to seek for channels down the band. Preset Station Seek Mode (AUTO2) Press the [ 3 ] button to move to the next preset station. Press the [ 2 ] button to move to the last ...

  • Kenwood LZ-701W - page 7

    Selecting the Seek Mode [SEEK MODE] <When the KTC-V800N or KTC-V800P is connected> Y ou can choose from three seek modes: auto seek, preset station seek, and manual seek. Press the [ 2 ] or [ 3 ] button, the mode switches as follows: [AUTO 1]: Auto Seek Mode 5 ∞ [AUTO 2]: Preset Station Seek Mode 5 ∞ [MANU]: Manual Seek Mode Channel Prese ...

  • Kenwood LZ-701W - page 8

    Setting the Remote Sensor On/Off [REMOTE] If this unit also runs when operating other units with different Kenwood remote controls, its remote control function can be turned off. Press the [ 2 ] or [ 3 ] button to switch the function on and off. FM T ransmitter Function [FM-TX] <When the KTC-V800N* or KTC-V800P is connected> Y ou can use the ...

  • Kenwood LZ-701W - page 9

    9 Remote Control Function <Provided with the KTC-V800N/KTC-V800P> Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries 1. Use two "AA" batteries: Slide the cover while pressing downwards to remove it as illustrated. 2. Insert the batteries with the ª and · poles aligned properly foll ...

  • Kenwood LZ-701W - page 10

    English 10 Installation Accessories External view ......... Number of items ........1 1 ........1 2 ........1 3 External view ......... Number of items ........5 4 ........2 5 (Ø4 x 12 mm) (Ø4 x 16 mm) Installation Procedure 1. T o prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery . 2. Make the ...

  • Kenwood LZ-701W - page 11

    11 • Be sure to use the supplied screws for installation. Using screws longer than those supplied may destroy parts inside the unit causing it to smoke. Using screws shorter than those supplied may cause the unit to come looks from the installation bracket. • If you are not going to install the unit using the supplied monitor stand, be sure to ...

  • Kenwood LZ-701W - page 12

    English 12 Installation Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A . Do not install in locations where the entire support is at a di ...

  • Kenwood LZ-701W - page 13

    13 Accessory 3 Accessory 4 (Ø4 x 12 mm) Protective strip Loosen T ighten T ighten Loosen Installation surface IM_W_English_ver.5 02.12.20 1:38 PM Page 13 ...

  • Kenwood LZ-701W - page 14

    English 14 Installation Installation for the Video Box Unit Accessory 5 (Ø4 x 16 mm) IM_W_English_ver.5 02.12.20 1:38 PM Page 14 ...

  • Kenwood LZ-701W - page 15

    15 – + TO MONITOR UNIT VIDEO IN VIDEO OUT POWER PRK SW ACC FM TX +12 V 2 AV INPUT AV OUTPUT 1 AV INPUT ANTENNA Connection Accessory 2 Accessory 1 Ignition wire (Red) ª 12V Parking sensor wire (Green) For the sake of safety , be sure to connect the parking sensor . 2 CAUTION Ignition key switch Car fuse box (Main fuse) ACC Ground wire (Black) · ...

  • Kenwood LZ-701W - page 16

    English 16 Tr oubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM Nothing happens when the buttons are pressed. The computer chip in the unit is not functioning ...

  • Kenwood LZ-701W - page 17

    17 Specifications Specifications subject to change without notice. Monitor Unit Screen size ....................................................................................7.0 inches wide 154.1(W) x 87.05(H) x 177(Diagonal) mm 6-1/16(W) x 3-7/16(H) inch Display system ..............................................................T ransparent TN ...

  • Kenwood LZ-701W - page 18

    LZ-701W(E)_00Cov_m2 02.12.20 1:39 PM Page 2 ...

Manufacturer Kenwood Category Car Stereo System

Documents that we receive from a manufacturer of a Kenwood LZ-701W can be divided into several groups. They are, among others:
- Kenwood technical drawings
- LZ-701W manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood LZ-701W
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood LZ-701W.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood LZ-701W, service manual, brief instructions and user manuals Kenwood LZ-701W. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood LZ-701W.

Similar manuals

A complete manual for the device Kenwood LZ-701W, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood LZ-701W by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood LZ-701W.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood LZ-701W - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood LZ-701W, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood LZ-701W, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood LZ-701W - which should help us in our first steps of using Kenwood LZ-701W
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood LZ-701W
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood LZ-701W in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood LZ-701W?

Use the form below

If you did not solve your problem by using a manual Kenwood LZ-701W, ask a question using the form below. If a user had a similar problem with Kenwood LZ-701W it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)